New techniques in geochemical analysis
Thin layer and gas chromatography, Mossbauer and atomic absorption spectrometry, fission track analysis, X-ray fluorescence spectroscopy, and other methods employed in geochemistry
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Thin layer and gas chromatography, Mossbauer and atomic absorption spectrometry, fission track analysis, X-ray fluorescence spectroscopy, and other methods employed in geochemistry
Kapton polyimide oxidizes at significant rates (4.3x10(-24) gram/incident oxygen atom) when exposed in low Earth orbit to the ram atomic oxygen flux. Ion beam sputter deposited thin films of Al2O3 and SiO2 as well as a codeposited mixture of predominantly SiO2 with a small amount of polytetrafluoroethylene were evaluated and found to be effective in protecting Kapton from oxidation in both laboratory plasma ashing tests as well as in space on board shuttle flight STS-8. A protective film of or = 96 percent SiO2 and or = 4 percent polytetrafluoroethylene was found to be very flexible compared to the pure metal oxide coatings and resulted in mass loss rates that were 0.2 percent of that of the unprotected Kapton. The optical properties of Kapton for wavelengths investigated between 0.33 and 2.2 microns were not significantly altered by the presence of the coatings or changed by exposure of the coated Kapton to the low Earth orbital ram environment.
Marangoni flow was induced in a thin disk of molten tin with an atomically clean surface by heating it from below in an ultra high vacuum apparatus. The radial distribution of temperature was measured and no temperature oscillations were observed. Strong mechanical disturbances introduced at a Marangoni number of about 4300 died out quickly with time indicating that the system was stable. Mathematical models indicate that strong flows in a two cell structure exist under the conditions studied, and that the velocity profile in the cell near the surface is of the boundary layer type which varies rapidly with depth.
Glass and glass ceramic samples exposed to the low earth orbit environment for approximately 5.5 years on the Long Duration Exposure Facility (LDEF) were found to display limited degradation in optical transmission. Commercial optical quality fused silica samples display decreases in transmission in the 200 to 400 nm wavelength region, and this degradation appears to be a consequence of surface contamination. The contamination, found only on internal surfaces of samples, was measured by medium energy backscattering spectrometry and found to be primarily carbon. Additional thin film contamination by a species with atomic mass near 64, which was present at the level of about 8 x 10 exp 14/sq. cm has not been identified. These observations are consistent with the interpretation that organic binders used in the black absorbing paint (Chem Glaze Z-306) inside the sample holding tray were concentrated in the vicinity of the samples and photolytically cracked by solar UV radiation. The resulting decomposition products were deposited on the interior sample surface and gave rise to the optical transmission loss. No detectable contamination was observed on the external or space exposed surface of the samples. No measurable damage was detected which could be attributed to the direct action of gamma or UV radiation on the glass samples. These results emphasize the need for special precautions in the preparation of spacecraft carrying precision optical components on long duration missions.
Dynamical aspects of a drop drastically flattened by acoustic radiation stress are considered. Its static equilibrium has been studied, starting with a dislike shape and modeling the sound field and the associated radiation stress according to this geometry. It is suggested that, at low viscosity, the ripples are capillary waves generated by the parametric instability excited by the membrane vibration, which is driven by the sound pressure. Atomization occurs whenever the membrane becomes so thin that the vibration is sufficiently intense. Buckling occurs when an existent equilibrium is unstable to a radial oscillation of the membrane because of the Bernoulli effect. The radiation stress at the rim of the flattened drop is also destabilizing and leads to horizontal expansion and subsequent breakup.
The deformation and break-up are studied of a liquid drop in levitation through the radiation pressure. Using high-speed photography ripples are observed on the central membrane of the drop, atomization of the membrane by emission of satellite drops from its unstable ripples, and shattering of the drop after upward buckling like an umbrella, or after horizontal expansion like a sheet. These effects are captured on video. The ripples are theorized to be capillary waves generated by the Faraday instability excited by the sound vibration. Atomization occurs whenever the membrane becomes so thin that the vibration is sufficiently intense. The vibration leads to a destabilizing Bernoulli correction in the static pressure. Buckling occurs when an existent equilibrium is unstable to a radial (i.e., tangential) motion of the membrane because of the Bernoulli effect. Besides, the radiation stress at the rim of the drop is a suction stress which can make equilibrium impossible, leading to the horizontal expansion and the subsequent break-up.
For historical reasons the hole count, an important performance test for the Analytical Electron Microscope (AEM), is somewhat arbitrary yielding different numbers for different investigators. This was not a problem a decade ago when AEM specimens were often bathed with large fluxes of stray electrons and hard x rays. At that time the presence or absence of a thick Pt second condenser (C2) aperture could be detected by a simple comparison of the x-ray spectrum taken 'somewhere in the hole' with a spectrum collected on a 'typical thickness' of Mo or Ag foil. A high hole count of about 10-20% indicated that the electron column needed modifications; whereas a hole count of 1-2% was accepted for most AEM work. The absolute level of the hole count is a function of test specimen atomic number, overall specimen shape, and thin-foil thickness. In order that equivalent results may be obtained for any AEM in any laboratory in the world, this test must become standardized. The hole-count test we seek must be as simpl and as nonsubjective as the graphite 0.344nm lattice-line-resolution test. This lattice-resolution test spurred manufacturers to improve the image resolution of the TEM significantly in the 1970s and led to the even more stringent resolution tests of today. A similar phenomenon for AEM instruments would be welcome. The hole-count test can also indicate whether the spurious x-ray signal is generated by high-energy continuum x rays (bremsstrahlung) generated in the electron column (high K-line to L-line ratio) or uncollimated electrons passing through or around the C2 aperture (low K/L ratio).
Metalorganic vapor phase epitaxy (MOVPE) of GaSb/InGaAsSb multilayer thin films and fabrication of bias-selectable dual band photodetectors are reported. For the dual band photodetectors the short wavelength detector, or the upper p- GaSb/n-GaSb junction photodiode, is placed optically ahead of the long wavelength one, or the lower photodiode. The latter is based on latticed-matched In0.13Ga0.87As0.11Sb0.89 with bandgap near 0.6 eV. Specifically, high quality multilayer thin films are grown sequentially from top to bottom as p+-GaSb/p-GaSb/n-GaSb/n-InGaAsSb/p-InGaAsSb/p-GaSb on undoped p-type GaSb substrate, and as n-GaSb/p-GaSb/p-InGaAsSb/n-InGaAsSb/n-GaSb on Te-doped n-type GaSb substrate respectively. The multilayer thin films are characterized by optical microscope, atomic force microscope (AFM), electron microprobe analyses etc. The photodiode mesa steps are patterned by photolithography with wet chemical etching and the front metallization is carried out by e-beam evaporation with Pd/Ge/Au/Ti/Au to give ohmic contact on both n- and p-type Sb based layer surfaces. Dark I-V measurements show typical diode behavior for both the upper and lower photodiodes. The photoresponsivity measurements indicate that both the upper and lower photodiodes can sense the infrared illumination corresponding to their cutoff wavelengths respectively, comparable with the simulation results. More work is underway to bring the long wavelength band to the medium infrared wavelength region near 4 micrometers.
The capacity of chemically-assisted focused ion beam (fib) etching systems to undertake direct and highly anisotropic erosion of thin and thick gold (or other high atomic number [Z])coatings on x-ray mask membranes/substrates provides new levels of precision, flexibility, simplification and rapidity in the manufacture of mask absorber patterns, allowing the fast prototyping of high aspect ratio, high-resolution masks for deep x-ray lithography.
The atomic and electronic structures at interfaces in thin films are typically different from the bulk and are vitally important in determining the physical properties of thin films. The interface between SrVO{sub 3}, chosen as a prototype for vanadium-based perovskite materials in this work, and LaAlO{sub 3} substrate is investigated by scanning transmission electron microscopy, electron energy-loss spectroscopy, and theoretical multi-electron calculations. Extra electrons have been detected on the interface layer by comparing the energy-loss near-edge structures of V-L{sub 3,2} edges to those from the film far from the interface. Monochromated EELS and theoretical calculations for SrVO{sub 3}, VO{sub 2}, and V{sub 2}O{sub 3} support this conclusion. The extra electrons appear to originate from a change in the local bonding configuration of V at the La-O terminated substrate surface as determined by Z-contrast imaging.
A porous membrane provides enhanced filtration of pollutants and particles by coating the membrane with conformal thin films of doped titanium dioxide via atomic layer deposition or, alternatively, sequential infiltration synthesis. The membrane can either be organic or inorganic, and the doping of the membrane, usually with nitrogen, is an important feature that shifts the optical absorption of the TiO2 from the UV range into the visible-light range. This enables the use of lower energy light, including sunlight, to activate the photocatalytic function of the film. The coating described in the present invention is compatible with virtually any porous membrane and allows for precise tuning of the pore size with molecular precision. The present invention presents a new coating process and chemical structure that provides catalytic activity, strongly enhanced by light, to both mitigate fouling and break down various organic pollutants in the process stream.
Atomic movement under application of external stimuli (i.e., electric field or mechanical stress) in oxide materials has not been observed due to a lack of experimental methods but has been well known to determine the electric polarization. Here, we investigated atomic movement arising from the ferroelectric response of BiFeO 3 thin films under the effect of an electric field and stress in real time using a combination of switching spectroscopy, time-resolved X-ray microdiffraction, and in situ stress engineering. Under an electric field applied to a BiFeO 3 film, the hysteresis loop of the reflected X-ray intensity was found to result from the opposing directions of displaced atoms between the up and down polarization states. An additional shift of atoms arising from the linearly increased dielectric component of the polarization in BiFeO 3 was confirmed through gradual reduction of the diffracted X-ray intensity. The electric-fieldinduced displacement of oxygen atoms was found to be larger than that of Fe atom for both ferroelectric switching and increase of the polarization. In conclusion, the effect of external stress on the BiFeO 3 thin film, which was controlled by applying an electric field to the highly piezoelectric substrate, showed smaller atomic shifts than for the case of applying an electric field to the film, despite the similar tetragonality.
We investigated the optical properties of amorphous and crystalline zinc tin oxide (ZTO) thin films grown on SiO{sub 2}/Si substrates with varying compositions via a co-sputtering deposition method at room temperature. The co-sputtering targets consist of SnO{sub 2} and ZnO. By varying the relative power ratio of the two targets, we demonstrate the ability to control the Sn and Zn composition of the resulting ZTO thin films. The ratio of [Sn]/([Sn] + [Zn]) atomic compositions was estimated at 11%, 29%, 42%, 54%, and 60%. Using a 600 °C annealing process, the as-grown amorphous ZTO films were transformed into crystalline ZTO films. The dielectric functions were obtained based on the measured ellipsometric angles, ψ and Δ. We determined the dielectric functions, absorption coefficients, and optical gap energies of ZTO thin films with varying compositions. The dielectric functions, absorption coefficients, and optical gap energies of amorphous and crystalline Zn{sub 2}SnO{sub 4} thin films were obtained at 29 at. % of Sn. Subgap states at 1.6 eV (A) and 2.8 eV (B) of ZnSnO alloys and Zn{sub 2}SnO{sub 4} films were found in the imaginary part of the dielectric function spectra. The subgap state intensities were reduced via a nitrogen gas annealing. Possible origins of the observed subgap states will be discussed.
We have enhanced hole injection and lifetime in organic light-emitting diodes (OLEDs) by incorporating the isomeric metal phthalocyanine, CuMePc, as a hole injection enhancer. The OLED devices containing CuMePc as a hole injection layer (HIL) exhibited higher luminous efficiency and operational lifetime than those using a CuPc layer and without a HIL. The effect of CuMePc thickness on device performance was investigated. Atomic force microscope (AFM) studies revealed that the thin films were smooth and uniform because the mixture of CuMePc isomers depressed crystallization within the layer. This may have caused the observed enhanced hole injection, indicating that CuMePc is a promising HIL material for highly efficient OLEDs.
The element composition modification is experimentally studied in PZT thin films obtained via the RF magnetron sputtering with variable working gas pressure. The experimental data were interpreted through the statistic simulation of thermalization and diffusion of sprayed Pb, Zr, and Ti atoms during the ion-plasma deposition of PZT thin films. The simulation data are shown to adequately describe (within the limits of 5%) the change in element composition at various pressures of the gas environment. The study conducted enables one to produce PZT thin films with a set element composition, which is essential for optimizing the electric and physical properties of solid solutions at the morphotropic phase boundary.
Using angle-dependent x-ray magnetic circular dichroism, we have measured magnetic hysteresis loops at the Co L2,3 edges of oxide-doped Co80Pt20 thin films. The magnetocrystalline anisotropy energy (MAE) of the Co atoms, which is the main source of the magnetocrystalline anisotropy of the CoPt magnetic grains, has been determined directly from these element-specific hysteresis loops. When the oxide volume fraction (OVF) is increased from 16.6% to 20.7%, the Co MAE has been found to decrease from 0.117 meV/atom to 0.076 meV/atom. While a larger OVF helps one to achieve a smaller grain size, it reduces the magnetocrystalline anisotropy, as demonstrated unambiguously from the direct Co MAE measurements. Our results suggest that those Co80Pt20:oxide films with an OVF between 19.1% and 20.7% are suitable candidates for high-density magnetic recording.
Low Earth orbital atomic oxygen is capable of eroding most polymeric materials typically used on spacecraft. Solar array blankets, thermal control polymers, and carbon fiber matrix composites are readily oxidized to become thinner and less capable of supporting the loads imposed upon them. Protective coatings have been developed that are durable to atomic oxygen to prevent oxidative erosion of the underlying polymers. However, the details of the surface roughness, coating defect density, and coating configuration can play a significant role as to whether or not the coating provides long duration atomic oxygen protection. Identical coatings on different surface roughness surfaces can have drastically different durability results. Examples and analysis of the causes of resultant differences in atomic oxygen protection are presented. Implications based on in-space experiences, ground laboratory testing, and computational modeling indicate that thin film vacuum-deposited aluminum protective coatings offer much less atomic oxygen protection than sputter-deposited silicon dioxide coatings.
We discuss how artificial engineered thin films consisting of (LaSr)(MnV)O 3 matrix and columnar nanocomposites oxides are deposited on single-crystal LaAlO 3 (111) substrates by using La 2/3 Sr 1/3 MnO 3 and V 2 O 3 targets. The epitaxial grown (LaSr)(MnV)O 3 thin-film matrix is embedded with self-assembled MnO and V 2 O 3 columns with a few nanometers in size. The atomic structure, chemistry, and electronic properties of columnar nanocomposite are determined and the bonding between the matrix and nanopillars is identified by using atomically resolved scanning transmission electron microscopy and electron energy loss spectroscopy.