Search NASA⌕ Search

SEARCH · Search NASA

Results for “finite element methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Influences of Quench Cooling Rate on Microstructure and Corrosion Resistance of Al-Cu-Mg Alloy Based on the End-Quenching Test

To investigate the effects of the quench cooling rate on corrosion resistance of Al-Cu-Mg alloy, an end-quenching test was conducted and the microstructures at different cooling rates were observed by SEM and TEM. Additionally, the corrosion resistance was characterized by an intergranular corrosion test and electrochemical test. Moreover, the finite element method was applied to simulate the end quenching process. The results indicate that the actual end quenching process can be approximated as one-dimensional heat transfer, and the cooling rate varies at different cooling distances. By affecting the microstructures, decreasing the cooling rate leads to a decline in the corrosion properties. Low cooling rates coarsen the constituent particles and grain boundary particles, resulting in a wide precipitation-free zone and an increase in the intensity of corrosion reactions. A high cooling rate concentrates on the intragranular precipitant, which can reduce the pitting depth and represents a conversion from localized corrosion to general corrosion.

36 MATERIALS SCIENCE↗

A robust process-structure model for predicting the joint interface structure in impact welding

The impact welding is gaining popularity in joining of dissimilar metals as any intermetallics are often very thin or discontinous with little to no heat affected zone resulting from the process. This work focuses on a recently developed impact welding technique, known as the Vaporizing Foil Actuator Welding (VFAW), which uses the pressure created from the electrically driven rapid vaporization of a thin metallic conductor to drive the flyer. A typical characteristic of an impact-welded joint is the wavy weld interface which is attributed to the complex interfacial kinematics resulting from the high-speed oblique impact of the metal plates. A numerical simulation framework based on the finite element method (FEM) with Eulerian formalism is developed to model the high-speed impact between the metal plates. The model accounts for the thermomechanical interactions in the process and captures the complex interfacial deformations. A thorough validation of the model is achieved by comparing the wave characteristics obtained from numerical simulations with the experimental results from vaporizing foil actuator welding. The amplitude and wavelength of the interfacial waves and the resulting joint microstructure is shown to be strongly dependent on the process conditions and the specific material system, which is well captured by the model.

42 ENGINEERING↗

Quasi photonic crystal fiber for chemical sensing purpose in the terahertz regime: design and analysis

In this work, a novel quasi-photonic crystal fiber has been proposed, for the first time, in the chemical sensing purpose in the terahertz (THz) regime. Along with the sensing response, power fraction, scattering loss, effective mode area, and V parameter have been numerically computed by the full-vector finite element method with anisotropic circular perfect matched layers. Numerically computed results show that the proposed sensor offers 70.94%, 71.06%, and 72.19% sensing responses for targeted analytes water, ethanol, and benzene respectively at the optical frequency f = 1 THz. Besides, effective mode area of 1.43 × 10{sup 5} µm{sup 2}, 1.48 × 10{sup 5} µm{sup 2} and 1.55 × 10{sup 5} µm{sup 2} have found at the same time for the same analytes. The Q-PCF model proposed in this paper have bright aspects for practical applications in clinical and diagnostic sensing, medical imaging, environmental monitoring purpose and many other fields related to it.

36 MATERIALS SCIENCE↗

Design and Performance Evaluation of Al{sub 2}O{sub 3}-SiC Composite for Direct-Bonded Copper Substrate

A computational material design approach is applied to propose a novel ceramic material for direct-bonded copper (DBC) substrate with enhanced thermal and structural performance. The material design inherently consists of many competing requirements that require careful decisions regarding key trade-offs in terms of material composition, inclusion size, shape, and distribution to achieve the target properties. The alumina-silicon (Al{sub 2}O{sub 3}-SiC) composite, as compared to commercial alumina, used in DBC is found to be the most suitable design among other candidates with improved thermal and structural properties. In order to study the performance characteristics and the effects of the new ceramic composite with improved properties in terms of structural behavior and fatigue life of the DBC substrate, the normal working and extreme thermal cycling conditions were simulated and analyzed using finite element method. The temperature, strain, and localized stress distribution within the substrate at a steady-state condition were analyzed, and the improved Coffin–Manson law was used to calculate the fatigue life of the substrate under extreme thermal cycling conditions. The proposed Al{sub 2}O{sub 3}-SiC composite is found to be more robust than the commercial alumina as DBC substrates considering the thermal–mechanical performance. The fatigue life cycle of the DBC substrate with the proposed material is predicted to be about two times longer than the commercial alumina DBC ceramic under transient thermal cycling test.

36 MATERIALS SCIENCE↗

Ultrasonic fingerprint sensor using a piezoelectric micromachined ultrasonic transducer array integrated with complementary metal oxide semiconductor electronics

This paper presents an ultrasonic fingerprint sensor based on a 24 × 8 array of 22 MHz piezoelectric micromachined ultrasonic transducers (PMUTs) with 100 μm pitch, fully integrated with 180 nm complementary metal oxide semiconductor (CMOS) circuitry through eutectic wafer bonding. Each PMUT is directly bonded to a dedicated CMOS receive amplifier, minimizing electrical parasitics and eliminating the need for through-silicon vias. The array frequency response and vibration mode-shape were characterized using laser Doppler vibrometry and verified via finite element method simulation. The array's acoustic output was measured using a hydrophone to be ∼14 kPa with a 28 V input, in reasonable agreement with predication from analytical calculation. Pulse-echo imaging of a 1D steel grating is demonstrated using electronic scanning of a 20 × 8 sub-array, resulting in 300 mV maximum received amplitude and 5:1 contrast ratio. Because the small size of this array limits the maximum image size, mechanical scanning was used to image a 2D polydimethylsiloxane fingerprint phantom (10 mm × 8 mm) at a 1.2 mm distance from the array.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

State of the art in electromagnetic modeling for the Compact Linear Collider

SLAC's Advanced Computations Department (ACD) has developed the parallel 3D electromagnetic time-domain code T3P for simulations of wakefields and transients in complex accelerator structures. T3P is based on state-of-the-art Finite Element methods on unstructured grids and features unconditional stability, quadratic surface approximation and up to 6th-order vector basis functions for unprecedented simulation accuracy. Optimized for large-scale parallel processing on leadership supercomputing facilities, T3P allows simulations of realistic 3D structures with fast turn-around times, aiding the design of the next generation of accelerator facilities. Applications include simulations of the proposed two-beam accelerator structures for the Compact Linear Collider (CLIC) - wakefield damping in the Power Extraction and Transfer Structure (PETS) and power transfer to the main beam accelerating structures are investigated.

43 PARTICLE ACCELERATORS↗

Predicting Fracture Toughness of TRIP 800 using Phase Properties Characterized by In-Situ High Energy X-Ray Diffraction

TRansformation Induced Plasticity (TRIP) steel is a typical representative of 1st generation advanced high strength steel (AHSS) which exhibits a combination of high strength and excellent ductility due to its multiphase microstructure. In this paper, we study the crack propagation behavior and fracture resistance of a TRIP 800 steel using a microstructure-based finite element method with the various phase properties characterized by in-situ high energy Xray diffraction (HEXRD) technique. Uniaxial tensile tests on the notched TRIP 800 sheet specimens were also conducted, and the experimentally measured tensile properties and R-curves (Resistance curves) were used to calibrate the modeling parameters and to validate the overall modeling results. The comparison between the simulated and experimentally measured results suggests that the micromechanics based modeling procedure can well capture the overall complex crack propagation behaviors and the fracture resistance of TRIP steels. The methodology adopted here may be used to estimate the fracture resistance of various multiphase materials.

36 MATERIALS SCIENCE↗

Acoustic beam splitting in two-dimensional phononic crystals using self-collimation effect

We propose two models of self-collimation-based beam splitters in phononic crystals. The finite element method is used to investigate the propagation properties of acoustic waves in two-dimensional phononic crystals. The calculated results show that the efficiency of the beam splitter can be controlled systematically by varying the radius of the rods or by changing the orientation of the square rods in the line defect. The effect of changing the side length of the square rods on acoustic wave propagation is discussed. The results show that the total transmission/reflection range decreases/increases as the side length increases. We also find that the relationship between the orientation of the transflective point and the side length of the square rods is quasi-linear.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Numerical—experimental analysis of two floor platform designs for auxiliary construction truck

In an auxiliary construction truck, the permanent deformations created by impact of rocks against the floor platform during the daily work generate the premature failure and need for replacement of the platform floor. This article shows the process followed in the analysis of two floor platforms for auxiliary construction trucks. This analysis has been carried out by means of the methodology developed in collaboration with truck manufacturer (ZAMARBU S.L) and the research group “New Technologies Applied on Vehicles and Road Safety” (VEHIVIAL) of the University of Zaragoza. The methodology applied in the floor platform development has been based on the application of numerical techniques by means of the finite element method (FEM) with explicit integration of dynamic equilibrium equation and the validation of the numerical results by means of experimental test. Applied load cases correspond to the impact of a sphere of 50, 150, and 250 kg. These load cases reproduce the impact caused by stones falling on the floor platform, which are the most restrictive for the floor design, because the vehicle’s rigidity and resistance against torsion and bending are provided for the chassis. The results of the analysis served to demonstrate the efficiency of the methodology developed for the optimization of the floor platform for auxiliary construction truck, getting an innovative floor platform design that improves the current models.

42 ENGINEERING↗

Sierra/SolidMechanics 4.56 Capabilities In Development

This user's guide documents capabilities in Sierra/SolidMechanics which remain "in-development" and thus are not tested and hardened to the standards of capabilities listed in Sierra/SM 4.56 User's Guide. Capabilities documented herein are available in Sierra/SM for experimental use only until their official release. These capabilities include, but are not limited to, novel discretization approaches such as peridynamics and the reproducing kernel particle method (RKPM), numerical fracture and failure modeling aids such as the extended finite element method (XFEM) and J-integral, explicit time step control techniques, dynamic mesh rebalancing, as well as a variety of new material models and finite element formulations.

97 MATHEMATICS AND COMPUTING↗

Sierra/SolidMechanics 4.52 Capabilities in Development

This user's guide documents capabilities in Sierra/SolidMechanics which remain "in-development" and thus are not tested and hardened to the standards of capabilities listed in Sierra/SM 4.52 User's Guide. Capabilities documented herein are available in Sierra/SM for experimental use only until their official release. These capabilities include, but are not limited to, novel discretization approaches such as peridynamics and the reproducing kernel particle method (RKPM), numerical fracture and failure modeling aids such as the extended finite element method (XFEM) and J-integral, explicit time step control techniques, dynamic mesh rebalancing, as well as a variety of new material models and finite element formulations.

97 MATHEMATICS AND COMPUTING↗

Numerical Simulation of Bulging Deformation for Wide-Thick Slab Under Uneven Cooling Conditions

In the present work, the bulging deformation of a wide-thick slab under uneven cooling conditions was studied using finite element method. The non-uniform solidification was first calculated using a 2D heat transfer model. The thermal material properties were derived based on a microsegregation model, and the water flux distribution was measured and applied to calculate the cooling boundary conditions. Based on the solidification results, a 3D bulging model was established. The 2D heat transfer model was verified by the measured shell thickness and the slab surface temperature, and the 3D bulging model was verified by the calculated maximum bulging deflections using formulas. The bulging deformation behavior of the wide-thick slab under uneven cooling condition was then determined, and the effect of uneven solidification, casting speed, and roll misalignment were investigated.

36 MATERIALS SCIENCE↗

The inverse problems of wing panel manufacture processes

It is shown that inverse problems of steady-state creep bending of plates in both the geometrically linear and nonlinear formulations can be represented in a variational formulation. Steady-state values of the obtained functionals corresponding to the solutions of the problems of inelastic deformation and springback are determined by applying a finite element procedure to the functionals. Optimal laws of creep deformation are formulated using the criterion of minimizing damage in the functionals of the inverse problems. The formulated problems are reduced to the problems solved by the finite element method using MSC.Marc software. Currently, forming of light metals poses tremendous challenges due to their low ductility at room temperature and their unusual deformation characteristics at hot-cold work: strong asymmetry between tensile and compressive behavior, and a very pronounced anisotropy. We used the constitutive models of steady-state creep of initially transverse isotropy structural materials the kind of the stress state has influence. The paper gives basics of the developed computer-aided system of design, modeling, and electronic simulation targeting the processes of manufacture of wing integral panels. The modeling results can be used to calculate the die tooling, determine the panel processibility, and control panel rejection in the course of forming.

36 MATERIALS SCIENCE↗

Intrinsic delay of permeable base transistor

Permeable base transistors (PBTs) fabricated by vacuum deposition or solution process have the advantages of easy fabrication and low power operation and are a promising device structure for flexible electronics. Intrinsic delay of PBT, which characterizes the speed of the transistor, is investigated by solving the three-dimensional Poisson equation and drift-diffusion equation self-consistently using finite element method. Decreasing the emitter thickness lowers the intrinsic delay by improving on-current, and a thinner base is also preferred for low intrinsic delay because of fewer carriers in the base region at off-state. The intrinsic delay exponentially decreases as the emitter contact Schottky barrier height decreases, and it linearly depends on the carrier mobility. With an optimized emitter contact barrier height and device geometry, a sub-nano-second intrinsic delay can be achieved with a carrier mobility of ∼10 cm{sup 2}/V/s obtainable in solution processed indium gallium zinc oxide, which indicates the potential of solution processed PBTs for GHz operations.

36 MATERIALS SCIENCE↗

A Numerical Study of Cracks Appearance on Tungsten Surface After High Intense Pulsed Ion Beam Irradiation

Due to the outstanding physical properties, Tungsten has been proposed for use in the divertor of future fusion devices. However, tungsten shall face strong particle bombardment from the plasma, which causes severe damage to the material. The purpose of this work is to build such an accurate analytical model which can predict the damages in target material like crack production and propagation after high intense pulsed ion beam irradiation. Hence, a two-dimensional finite element method is used to study the effect of high intense pulsed ion beam on tungsten surface numerically. To judge temperature and stress distribution in material, thermal conduction model is combined with non-linear fracture mechanics model and J-Integral parameter is used as a criterion to judge the crack propagation. Simulation results reveal that different crack heights and sizes can affect the results and there is a critical depth for crack propagation. The model gives good results to real experimental observations and has potential applications for different intense pulsed electron/plasma beams and different target materials as well.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Finite element solution of MHD power-law fluid with slip velocity effect and non-uniform heat source/sink

The laminar steady boundary layer flow of an incompressible MHD Power-law fluid past a continuously moving surface is investigated numerically. The study involves the influence of surface slip and non-uniform heat source/sink on the flow and heat transfer. The governing boundary layer flow equations are transformed into non-dimensional, non-linear coupled ordinary differential equations with the help of suitable similarity transformations. The Galerkin finite element method is implemented to crack the resulting system. The impact of different involved physical parameters is exhibited on the dimensionless velocity profile, temperature distributions and rate of heat transfer in graphical and tabular forms for pseudoplastic and dilatant fluids. The local Nusselt number is found to be the decreasing function of slip parameter, temperature and space-dependent heat sink parameter whereas it increases with increasing values of temperature and space dependent heat source parameter. The problem has important application in attaining the sustainable heat transfer rate for the cooling of fluids, especially in heat exchangers used frequently in chemical industry, in order to increase the trustworthiness of a system, as it removes high heat loads from these systems.

97 MATHEMATICS AND COMPUTING↗

Smoothed boundary method for simulating incompressible flow in complex geometries

Simulating flow through porous media with explicit considerations of complex microstructures is very challenging using conventional sharp-interface methods because of the difficulties in generating meshes conformal to complex geometries. In this work, a diffuse interface embedded boundary method known as the Smoothed Boundary Method (SBM) is utilized to facilitate simulations of fluid dynamics involving complex geometries. In diffuse-interface methods, the geometry is described by a domain parameter. The SBM allows the straightforward reformulation of the time-dependent Navier-Stokes equations in terms of this domain parameter, using only algebraic identities. Thus, enforcing the appropriate boundary conditions at the irregular embedded boundary is greatly simplified. Adaptive mesh refinement is used to increase the accuracy of the diffuse interface method by allowing thinner interfacial thickness to be used in the domain parameter. Here, the SBM-formulated Navier-Stokes equations are solved with the Finite Difference Method on refined mesh systems. Sharp-interface Finite Element Method simulations using the commercial software COMSOL on body-conforming meshes are also provided for comparison. Favorable agreement between the two methods is observed. Since it is no longer necessary for the mesh to conform to the complex geometry, the grid system for the SBM simulations can be generated rapidly and without additional manual interventions, making the entire simulation process more expedient.

36 MATERIALS SCIENCE↗

High Order Finite Elements S{sub N} Transport in X-Y Geometry on Meshes with Curved Surfaces

Radiation hydrodynamics is useful to model astrophysics, ICF, and glass manufacturing. A large amount of research has been conducted to understand how to solve hydrodynamics equations using high-order finite elements. Researchers at LLNL have developed a general high-order FEM library, Modular Finite Element Methods (MFEM), to enable this research. The BLAST code uses MFEM to evolve the Lagrangian hydrodynamics equations, resulting in meshes with higher order curved surfaces. Our research focuses on the requirements for high order finite element solutions of the radiation transport equation with the eventual goal of studying the complete high-order radiation hydrodynamics solution methodology. For this research we used MFEM to develop a proof-of-concept code that solves the high order finite element transport equations in Cartesian coordinates on meshes with curved surfaces. We have solved several test problems to assess the behavior of our method. (authors)

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗