Search NASA⌕ Search

SEARCH · Search NASA

Results for “parameter optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Oxide Removal from the InSb Plate Surface to Produce Lateral Spin Valves

Abstracts: The formation conditions of a smooth and oxide-free surface of InSb semiconductor with the purpose of fabricating lateral spin devices based on it are investigated. The dry etching rate by Ar ions of the surface of the crystalline faces (100) of InSb plates as well as a variation in their roughness depending on the power supplied to ion etching devices are investigated. The degree of oxidation of the semiconductor surface exposed to air after ion cleaning and annealing in molecular hydrogen are evaluated. Based on comparison of the efficiency of spin injection in devices formed with semiconductors subjected to various types of treatment, a conclusion is made about the parameters of optimal preparation of the surface of the InSb wafers for the fabrication of lateral spin devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Connecting Material Properties and Redox Flow Cell Cycling Performance through Zero-Dimensional Models

Improvements in redox flow battery (RFB) performance and durability can be achieved through the development of new active materials, electrolytes, and membranes. While a rich design space exists for emerging materials, complex tradeoffs challenge the articulation of unambiguous target criteria, as the relationships between component selection and cycling performance are multifaceted. Here, we derive zero-dimensional, analytical expressions for mass balances and cell voltages under galvanostatic cycling, enabling direct connections between material/electrolyte properties, cell operating conditions, and resulting performance metrics (e.g., energy efficiency, capacity fade). To demonstrate the utility of this modeling framework, we highlight several considerations for RFB design, including upper bound estimation, active species decay, and membrane/separator conductivity-selectivity tradeoffs. Furthermore, we also discuss modalities for extending this framework to incorporate kinetic losses, distributed ohmic losses, and multiple spatial domains. Importantly, because the mass balances are solved analytically, hundreds of cycles can be simulated in seconds, potentially facilitating detailed parametric sweeps, system optimization, and parameter estimation from cycling experiments. More broadly, this approach provides a means for assessing the impact of cell components that simultaneously influence multiple performance-defining processes, aiding in the elucidation of key descriptors and the identification of favorable materials combinations for specific applications.

25 ENERGY STORAGE↗

High Resolution Aerosol Jet Printed Components with Electrodeposition-Enhanced Conductance

Aerosol Jet Printing (AJP) is one technique of additive manufacturing used in the printing of electronics components. AJP enables the patterning of features at the ~10 μm–100 μm scale based on hardware and print parameters. Additionally, optimization of print conditions enables the printing of high-resolution features with linewidths approaching 10 μm. The aerosol jet printing of electronic parts can be limited by the conductivities which are achievable by Ag nanoparticle inks (typically 15%–25% of bulk Ag). For certain electronics applications, the increased conductivity produces unacceptable loses during operation and methods are needed to increase the conductance of the devices without sacrificing resolution. Here, we report on the AJP of inductor spirals conductor traces of linewidth 50 μm separated by 55 μm gaps. The conductivity of these features is enhanced by electrodeposition of Cu onto the Ag, resulting in a decrease in resistance of 35–45x. Impedance measurements demonstrate that the addition of Cu by electrodeposition to a 27-turn spiral inductor resulted in an inductance of 3.6 μH. Finally, we demonstrate the use of a lift-off process to produce free-standing, flexible, conductive films using AJP.

36 MATERIALS SCIENCE↗

Neural Networks for Supercapacitor Modeling

This software implements a one-dimensional model of a supercapacitor and calibrates it to experimental data. A system of coupled partial differential equation models the salt concentration and the ionic and electronic potentials. The term in the equation modeling the capacitance contains a neural network, whose parameters are optimized to fit the provided experimental data. The software is written in python using the open-source library JAX to calculate the gradients needed for the optimization.

Salazar de Troya, Miquel↗

Out of Distribution Detection with Neural Network Anchoring

This is code to reproduce and build on OOD detection from the paper "Out of Distribution Detection with Neural Network Anchoring". Our goal here is to exploit heteroscedastic temperature scaling as a calibration strategy for out of distribution (OOD) detection. Heteroscedasticity here refers to the fact that the optimal temperature parameter for each sample can be different, as opposed to conventional approaches that use the same value for the entire distribution. To enable this, we propose a new training strategy called anchoring that can estimate appropriate temperature values for each sample, leading to state-of-the-art OOD detection performance across several benchmarks. Using NTK theory, we show that this temperature function estimate is closely linked to the epistemic uncertainty of the classifier, which explains its behavior. In contrast to some of the best-performing OOD detection approaches, our method does not require exposure to additional outlier datasets, custom calibration objectives, or model ensembling. Through empirical studies with different OOD detection settings - far OOD, near OOD, and semantically coherent OOD - we establish a highly effective OOD detection approach.

Thiagarajan, Jayaraman↗

Cylindrical battery design app

Software that delivers optimal design parameters and performance predictions for cylindrical cells, which can range in size from microbatteries to EV batteries, is developed. The software utilizes machine learning and includes a graphical user interface to enable rapid prototyping and to accelerate energy storage research, development, and manufacturing. The Cylindrical battery design V1.0 comprises of three types of cylindrical batteries, Microbattery (Primary), Microbattery (Secondary) and 18650/21700/xxxxx Cylindrical battery. The software was developed in MATLAB. The software has the capability to output the cell design with the capacity ranges from several mAh to several million Ah.

Xiao, Jie↗

Discrete event performance prediction of speculatively parallel temperature-accelerated dynamics

Due to its unrivaled ability to predict the dynamical evolution of interacting atoms, molecular dynamics (MD) is a widely used computational method in theoretical chemistry, physics, biology, and engineering. Despite its success, MD is only capable of modeling time scales within several orders of magnitude of thermal vibrations, leaving out many important phenomena that occur at slower rates. The Temperature Accelerated Dynamics (TAD) method overcomes this limitation by thermally accelerating the state-to-state evolution captured by MD. Due to the algorithmically complex nature of the serial TAD procedure, implementations have yet to improve performance by parallelizing the concurrent exploration of multiple states. Here we utilize a discrete event-based application simulator to introduce and explore a new Speculatively Parallel TAD (SpecTAD) method. We investigate the SpecTAD algorithm, without a full-scale implementation, by constructing an application simulator proxy (SpecTADSim). Finally, following this method, we discover that a nontrivial relationship exists between the optimal SpecTAD parameter set and the number of CPU cores available at run-time. Furthermore, we find that a majority of the available SpecTAD boost can be achieved within an existing TAD application using relatively simple algorithm modifications.

97 MATHEMATICS AND COMPUTING↗

Advancing continuous enzymatic hydrolysis for improved biomass saccharification

Background: A deployable, continuous enzymatic hydrolysis (CEH) process can address cost and commercialization risks associated with second-generation (Gen2) biorefinery sugar/lignin/ethanol production while contributing to energy supply and security. Developments in commercial enzymatic hydrolysis formulations targeting Gen2 pretreated biomass such as deacetylated mechanically refined (DMR) biomass necessitate a reassessment of the existing hybrid simultaneous saccharification and fermentation (SSF) approach. Notably, the practice of "finishing hydrolysis" in SSF has become problematic with the introduction of oxidative enzymes, such as lytic polysaccharide monooxygenases (LPMOs), into commercial cellulase formulations as these require specific redox conditions and cofactor. Moreover, continuous SSF has not been demonstrated at commercial scale, limiting deployment and the associated economic benefits to farmers, producers, and support industries. Results: Continuous enzymatic hydrolysis (CEH) was demonstrated at bench scale to enable optimal saccharification performance of deacetylated mechanically refined (DMR) pretreated biomass. Diafiltration was demonstrated to retain pretreated biomass solids and enzymes for continuous reaction while removing solubilized product sugars in situ. A significant breakthrough afforded by the CEH process is its ability to achieve equivalent endpoint conversions with approximately 50% lower enzyme loading. Yields of glucose and xylose were increased ~ 15% and ~ 4%, respectively, over batch hydrolysis. Unlike SSF using yeast or Zymomonas, CEH allows precise optimization of pH, temperature, oxygen tension, LPMO mediator concentration, and removal of end-product inhibitors. Conclusions: Advanced CEH holds promise as a transformational, process-intensified, and cost-effective method for producing soluble clarified biomass sugars and insoluble lignin-rich streams. Enhancing saccharification performance, optimizing operating parameters, and employing membrane filtration will help overcome existing challenges and enable the efficient production of valuable biomaterials from lignocellulosic biomass.

09 BIOMASS FUELS↗

Design and characterization of microstrip patch antennas for high-T c superconducting terahertz emitters

We designed and characterized a microstrip pattern of planar patch antennas compatible with a cuprate high- T c superconducting terahertz emitter. Antenna parameters were optimized using an electromagnetic simulator. We observed repeatable sub-terahertz emissions from each mesa fabricated on identical Bi 2 Sr 2 CaCu 2 O 8+δ base crystals in a continuous frequency range of 0.35–0.85 THz. Although there was no significant output power enhancement, a plateau behavior at a fixed frequency was observed below 40 K, indicating moderate impedance matching attributable to the ambient microstrip pattern. A remarkably anisotropic polarization at an axial ratio of up to 16.9 indicates a mode-locking effect. Our results enable constructing compactly assembled, monolithic, and broadly tunable superconducting terahertz sources.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Improving high temperature resilience of fiber sensor embedded smart components through laser shock peening

This study explores the use of laser shock peening (LSP) to enhance material properties and high-temperature performance of fiber-sensor-fused smart parts fabricated by additive manufacturing (AM) methods. Using embedded fiber sensors as distributed strain gauges, the study demonstrates that LSP can induce compressive strains of up to 130 µε on fiber embedded 1-mm below metal surfaces. The electron backscatter diffraction (EBSD) analysis shows that, with optimized LSP parameters, the metallic matrix undergoes substantial microstructural refinement, resulting in denser structures. Thermal cycling tests showed that the LSP process can increase fiber slippage temperatures by more than 50 °C. This work shows that the LSP process is an effective room-temperature process for enhancing both surface quality and increasing fiber slippage threshold under both thermal and mechanical stress.

Zhong, Shuda [University of Pittsburgh, PA (United↗

Small-angle X-ray scattering characteristics of mouse brain: Planar imaging measurements and tomographic imaging simulations

Small-angle x-ray scattering (SAXS) imaging can differentiate tissue types based on their nanoscale molecular structure. However, characterization of the coherent scattering cross-section profile of relevant tissues is needed to optimally design SAXS imaging techniques for a variety of biomedical applications. Reported measured nervous tissue x-ray scattering cross sections under a synchrotron source have had limited agreement. We report a set of x-ray cross-section measurements obtained from planar SAXS imaging of 1 mm thick mouse brain (APP/PS1 wild-type) coronal slices using an 8 keV laboratory x-ray source. Two characteristic peaks were found at 0.96 and 1.60 nm -1 attributed to myelin. The peak intensities varied by location in the slice. We found that regions of gray matter, white matter, and corpus callosum could be segmented by their increasing intensities of myelin peaks respectively. Measured small-angle x-ray scattering cross sections were then used to define brain tissue scattering properties in a GPU-accelerated Monte Carlo simulation of SAXS computed tomography (CT) using a higher monochromatic x-ray energy (20 keV) to study design trade-offs for noninvasive in vivo SAXS imaging on a small-animal head including radiation dose, signal-to-noise ratio (SNR), and the effect of skull presence on the previous two metrics. Simulation results show the estimated total dose to the mouse head for a single SAXS-CT slice was 149.4 mGy. The pixel SNR was approximately 30.8 for white matter material whether or not a skull was present. In this early-stage proof-of-principle work, we have demonstrated our brain cross-section data and simulation tools can be used to assess optimal instrument parameters for dedicated small-animal SAXS-CT prototypes.

59 BASIC BIOLOGICAL SCIENCES↗

Assessment of BOLD and GenBank – Their accuracy and reliability for the identification of biological materials

Taxonomic identification of biological materials can be achieved through DNA barcoding, where an unknown “barcode” sequence is compared to a reference database. In many disciplines, obtaining accurate taxonomic identifications can be imperative (e.g., evolutionary biology, food regulatory compliance, forensics). The Barcode of Life DataSystems (BOLD) and GenBank are the main public repositories of DNA barcode sequences. In this study, an assessment of the accuracy and reliability of sequences in these databases was performed. To achieve this, 1) curated reference materials for plants, macro-fungi and insects were obtained from national collections, 2) relevant barcode sequences (rbcL, matK, trnH-psbA, ITS and COI) from these reference samples were generated and used for searching against both databases, and 3) optimal search parameters were determined that ensure the best match to the known species in either database. While GenBank outperformed BOLD for species-level identification of insect taxa (53% and 35%, respectively), both databases performed comparably for plants and macro-fungi (~81% and ~57%, respectively). Results illustrated that using a multi-locus barcode approach increased identification success. This study outlines the utility of the BLAST search tool in GenBank and the BOLD identification engine for taxonomic identifications and identifies some precautions needed when using public sequence repositories in applied scientific disciplines.

59 BASIC BIOLOGICAL SCIENCES↗

From lapis lazuli to ultramarine blue: investigating Cennino Cennini’s recipe using sulfur K-edge XANES

As one of the most desired and expensive artists’ materials throughout history, there has long been interest in studying natural lapis lazuli. The traditional method of extracting the blue component, lazurite, from lapis lazuli, as outlined in Cennini’s Il Libro dell’Arte , involves a lengthy purification process: (1) finely grind the rock; (2) mix with pine rosin, gum mastic, and beeswax; (3) massage in water to collect the lazurite. Repeating the process produces several grades of the pigment, typically referred to as ultramarine blue. Here, we investigate the sulfur environment within the aluminosilicate framework of lazurite during its extraction from lapis lazuli. The sulfur XANES fingerprint from samples taken at the different stages in Cennini’s extraction method were examined. All spectra contain a strong absorption peak at 2483 eV, attributable to sulfate present in the lazurite structure. However, intensity variations appear in the broad envelope of peaks between 2470 and 2475 eV and the pre-peak at 2469.1 eV, indicating a variation in the content of trisulfur (S 3 –˙ ) radicals. By studying the effect of each step of Cennini’s process, this study elucidates the changes occurring during the extraction and the variability within different grades of the precious coloring material. The increasing application of XANES to the study of artist’s materials and works of art motivated extending the research to assess the possibility of X-ray induced damage. Direct comparison of micro-focused and unfocused beam experiments suggests an increase of the S 3 –˙ radicals with prolonged exposure. Furthermore, analysis indicates that induced damage follows first-order kinetics, providing a first assessment on the acceptable amount of radiation exposure to define the optimal acquisition parameters to allow safe analyses of lapis lazuli and ultramarine pigments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Field and Model Data Associated with the Manuscript “Drivers of Streamflow Intermittency in Humid Regions: 1. Evaluating Above- and Below-ground Controls of Flow Persistence in a Forested Catchment”

This package contains field data, modeling files, and scripts supporting the investigation of the drivers of streamflow intermittency in a forested catchment. It includes the field data collected from electrical resistivity tomography (ERT) surveys, ground penetrating radar (GPR), continuous self-potential (SP) monitoring, electromagnetic (EM) imaging, groundwater and stilling well. In addition, it contains the data and results of the coupled water- and electrical-flow model developed using the COMSOL Multiphysics and Advanced Terrestrial Simulator (ATS), as well as software files and Jupyter notebooks used to process the data and generate figures in the manuscript submitted for peer review. The data archive is organized in the following directories: 1) Climate Includes hourly precipitation and daily evapotranspiration time series (2024 – 2025) provided as CSV files, alongside a text file detailing dataset units. 2) Coupled_model Contains two subfolders: Synthetic and Field_Application subfolder. Synthetic subfolder contains the ATS XML input script (can be opened using any code editor) for the four synthetic hydrological cases tested (Connected and gaining, Connected and losing, Disconnected and losing, and dry stream). It also includes other experimental cases to test the influence of precipitation and concentration gradient. For each synthetic case, the flow model simulation is executed using the ATS XML scripts and the included Python script (generate_data_set.py) to convert ATS output to COMSOL-ready input. COMSOL Multiphysics template (.mph can be opened with the commercial software COMSOL and requires a license) is executed using the ATS output data to simulate the potential field. It also includes the Synthetic_model_plot.ipynb (can be opened using any code editor) to visualize the SP result and generate manuscript figures. The data subfolder contains mesh files to run both the ATS (.exo and .stl files can be viewed using Paraview; .h5 files can be opened using HDFView software and h5py Python package) and COMSOL models. Field_Application subfolder contains two subfolders: ES_MDA_inversion and Final_Model. ES_MDA_inversion contains the Python script (.py can be opened using any code editor) and SP observation data used to run the Ensemble Smoother with Multiple Data Assimilation (ES-MDA) inversion sequence to get the optimal model parameters. The Final_model subfolder contains the ATS XML input scripts, data files, output data for the two SP sites. The same workflow steps outlined for the Synthetic subfolder apply here. It also contains the Jupyter notebook (Plot_final_calib.ipynb) to visualize the results of the modeled SP, stream-groundwater exchange and moisture content. 3) Discharge Includes the electrical conductivity (EC) time series (provided as CSV files) from salt slug injections. It also includes the Jupyter notebook (Discharge_process.ipynyb) used to estimate discharge. All discharge measurements collated into rating_curve_processed.csv 4) EM Contains the CSV file of the EM data from the DUALEM-42, including spatial coordinates (x, y, z), apparent conductivity, and in-phase measurements at 2 m coil separations for horizontal coplanar (HCP) and perpendicular (PRP) geometries. 5) ERT Contains raw resistivity data (provided as CSV files), spatial location of each of the electrodes (provided as CSV files), and files used for the resistivity inversion (.resipy can be opened with the open-source ResIPy software). 6) GPR Includes GPR field datasets collected at 100 MHz and 250 MHz antenna frequencies, along with the processing/interpretation project file (GPR_process.gpz can be viewed using EKKO_Project 6, a commercial software by Sensors & Software that requires a license). 7) Slug_test Includes the slug test data at all the groundwater wells provided as CSV files, as well as the Jupyter notebook (Slug_test.ipynb) for calculating hydraulic conductivity. 8) SP Contains the SP data collected in field at the two SP sites (one in the perennial reach and the other in the intermittent reach), provided as DAT files. 9) Well_data Contains two subfolders: 1) Raw, which provides unprocessed pressure, electrical conductivity and temperature timeseries downloaded from the loggers in all the groundwater and stilling wells, and 2) Processed, which contains sorted, QA/QC timeseries data for each well. The data archive also contains data_process.ipynb, a Jupyter notebook used for field data analysis and generating figures (plotting well, SP, climate, and discharge data, as well as calculating head gradient at sites with nested groundwater wells). It also includes DTW.ipynb, a Jupyter notebook containing the code for the dynamic time warping (DTW) with sliding window to evaluate SP signal synchronicity.

ATS↗

On the direct ink write (DIW) 3D printing of styrene-butadiene rubber (SBR)-based adhesive sealant

Direct Ink Writing (DIW) utilizes a wide range of ink formulations to produce desirable 3D-printed structures and properties. Styrene-butadiene rubber (SBR) is an attractive candidate for 3D printing owing to its commercial availability, rheology, excellent mechanical properties, good impact resilience, and chemical stability. The SBR-based sealant was 3D printed in a DIW process, even in an ambient environment. The rheological behavior was assessed and correlated with optimized printing parameters. Important physico-chemical properties of the 3D-printed material were reported showing excellent properties as an elastomer. Finally, this work should expand the potential applications of existing rubber-based materials in additive manufacturing.

36 MATERIALS SCIENCE↗

Thermal contact conductance as a method of rectification in bulk materials

A thermal rectifier that utilizes thermal expansion to directionally control interfacial conductance between two contacting surfaces is presented. The device consists of two thermal reservoirs contacting a beam with one rough and one smooth end. When the temperature of reservoir in contact with the smooth surface is raised, a similar temperature rise will occur in the beam, causing it to expand, thus increasing the contact pressure at the rough interface and reducing the interfacial contact resistance. However, if the temperature of the reservoir in contact with the rough interface is raised, the large contact resistance will prevent a similar temperature rise in the beam. As a result, the contact pressure will be marginally affected and the contact resistance will not change appreciably. Owing to the decreased contact resistance of the first scenario compared to the second, thermal rectification occurs. A parametric analysis is used to determine optimal device parameters including surface roughness, contact pressure, and device length. Modeling predicts that rectification factors greater than 2 are possible at thermal biases as small as 3 K. Lastly, thin surface coatings are discussed as a method to control the temperature bias at which maximum rectification occurs.

36 MATERIALS SCIENCE↗

Plasma Processing to Reduce Field Emission in LCLS-II 1.3 GHz SRF Cavities

Plasma cleaning for LCLS-II 9-cell 1.3 GHz cavities is under study at Fermilab. Starting from ORNL method, we have developed a new technique for plasma ignition using HOMs. Plasma processing is being applied to contaminated and field emitting cavities, here are discussed the first results in terms of Q and radiation vs E measured before and after treatment. Further studies are ongoing to optimize plasma parameters and to acquire statistics on plasma cleaning effectiveness.

43 PARTICLE ACCELERATORS↗