Search NASA⌕ Search

SEARCH · Search NASA

Results for “shape function”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

On-line, adaptive state estimator for active noise control

Dynamic characteristics of airframe structures are expected to vary as aircraft flight conditions change. Accurate knowledge of the changing dynamic characteristics is crucial to enhancing the performance of the active noise control system using feedback control. This research investigates the development of an adaptive, on-line state estimator using a neural network concept to conduct active noise control. In this research, an algorithm has been developed that can be used to estimate displacement and velocity responses at any locations on the structure from a limited number of acceleration measurements and input force information. The algorithm employs band-pass filters to extract from the measurement signal the frequency contents corresponding to a desired mode. The filtered signal is then used to train a neural network which consists of a linear neuron with three weights. The structure of the neural network is designed as simple as possible to increase the sampling frequency as much as possible. The weights obtained through neural network training are then used to construct the transfer function of a mode in z-domain and to identify modal properties of each mode. By using the identified transfer function and interpolating the mode shape obtained at sensor locations, the displacement and velocity responses are estimated with reasonable accuracy at any locations on the structure. The accuracy of the response estimates depends on the number of modes incorporated in the estimates and the number of sensors employed to conduct mode shape interpolation. Computer simulation demonstrates that the algorithm is capable of adapting to the varying dynamic characteristics of structural properties. Experimental implementation of the algorithm on a DSP (digital signal processing) board for a plate structure is underway. The algorithm is expected to reach the sampling frequency range of about 10 kHz to 20 kHz which needs to be maintained for a typical active noise control application.

Lim, Tae W.↗

The evolutionary status of the stellar population in the rho Ophiuchi cloud core

This contribution reports the results of an infrared imaging survey aimed at characterizing the stellar populations associated with the three densest star-forming cores in the Ophiuchus molecular cloud complex. The survey has sufficient sensitivity at J, H, and K (at 5 sigma limits of 16.5, 15.4, and 14.2) to provide a complete census of embedded young stellar objects (YSOs) with masses greater than the hydrogen-burning limit, provided that their ages are less than 3 Myr and that they are obscured by no more than approximately 18 mag of visual extinction. Our data suggest (1) a large fraction (greater than 70%) of the sources located within the cores are still surrounded by circumstellar disks and/or envelopes; and (2) the shape of the initial mass function for masses, M less than 1 solar mass, appears to be consistent with that derived from the solar neighborhood. We also report the results of a deeper imaging survey of centimeter continuum sources (14 sources) in these star-forming cores and in the larger Ophiuchus complex (eight sources). A large fraction (11/14) of the radio sources associated with the cores appear to have infrared excesses diagnostic of circumstellar accretion disks and/or infalling circumstellar envelopes. In these cases, the centimeter continuum radiation most likely diagnoses the ionized component of energetic winds or jets which characterizes YSOs during the disk accretion phase. By contrast, of the eight radio sources located outside dense cores, only two show infrared excesses.

Strom, Karen M.↗

Simulations of particle acceleration in parallel shocks: Direct comparison between Monte Carlo and one-dimensional hybrid codes

We have made a direct comparison between two different computer simulations of a plane, parallel, collisionless shock including particle acceleration to energies typical of those of diffuse ions observed at the earth bow shock. Despite the fact that the one-dimensional hybrid and Monte Carlo techniques employ entirely different algorithms, they give surprisingly close agreement in the overall shapes of the complete distribution functions for protons as well as heavier ions. Both methods show that energetic ions emerge smoothly from the background thermal plasma with approximately the same relative injection rate and that the fraction of the incoming plasma's energy flux that is converted into downstream enthalpy flux of the accelerated population (i.e., the acceleration efficiency) is similar in the two cases. The fraction of the downstream proton distribution made up of superthermal particles is quite large, with at least 10% of the energy flux going into protons with energies above 10 keV. In addition, an upstream precursor, produced by backstreaming energetic particles, is present in both shocks, although the Monte Carlo precursor is considerably longer than that produced in the hybrid shock. These results offer convincing evidence that, at least in these ways, the two simulations are consistent in their description of parallel shock structure and particle acceleration, and they lay the groundwork for development of shock models employing a combination of both methods.

Ellison, Donald C.↗

Interactive method for planning constrained, fuel-optimal orbital proximity operations

An interactive graphical method for planning fuel-efficient rendezvous trajectories in the multi-spacecraft environment of the space station is presented. The method allows the operator to compose a multi-burn transfer trajectory between arbitrary initial chaser and target trajectories. The available task time of the mission is limited and the maneuver is subject to various operational constraints, such as departure, arrival, plume impingement and spatial constraints. The maneuvers are described in terms of the relataive motion experienced in a Space-Station centered coordinate system. The optimization method is based on the primer vector and its extension to non-optimal trajectories. The visual feedback of trajectory shapes, operational constraints, and optimization functions, provided by user-transparaent and continuously active background computations, allows the operator to make fast, iterative design changes which rapidly converge to fuel-efficient solutions. The optimization functions are presented. A variety of simple design examples has been presented to demonstrate the usefulness of the method. In many cases the addition of a properly positioned intermediate waypoint resulted in fuel savings of up to 30%. Furthermore, due to the counter-intuitive character of the optimization functions, most fuel-optimal solutions could not have been found without the aid of the optimization tools. Operating the system was found to be very easy, and did not require any previous in-depth knowledge of orbital dynamics or trajectory. The planning tool is an example of operator assisted optimization of nonlinear cost-functions.

Abramovitz, Adrian↗

A theoretical derivation of the dependence of the remotely sensed reflectance of the ocean on the inherent optical properties

An expression for the ratio of the upwelling nadir radiance L(pi, z) and the downwelling scalar irradiance E(sub od)(Z) is derived from the following equation of radiative transfer. This expression is given by RSR(z) = (L(pi, z))/E(sub od) = (f(sub b)(z)b(sub b)(z))/2 pi(k(pi, z) + c(z) - F(sub L)(z)b(sub f)(z)), where b(sub b)(z) is the backscattering coefficient, k(pi, z) is the vertical attenuation coefficient of the nadir radiance, c(z) is the beam attenuation coefficient, and f(sub b)(z) and f(sub L)(z) are shape parameters that depend on the shape of the volume scattering function and the radiance distribution. Successive approximations are subsequently applied to the above exact equation. These are f(sub b)(z) = (2 pi beta(pi - theta(sub m), z)/(b(sub b)(z))), where beta(pi - theta(sub m), z) is the volume scattering function at 180 deg minus the zenith angle of the maximum radiance, and k(pi, z) = am = c(1 - 0.52 b/c - 0.44 (b/c)(exp 2)), where m is a parameter that is numerically equal to the inverse of the average cosine of the asymptotic light field for a medium with the same inherent optical properties, a is the absorption coefficient, and b/c is the single scattering albedo. Together with f(sub L)(z) = 1.05 and application of Gershun's equation, it is shown that for nearly all oceanic cases RSR(z) identical to L(pi, z)/E(sub od)(z) = (Beta(pi - theta(sub m), z))/(a(z)(1 + m(z))).

Zaneveld, J. Ronald V.↗

Potential theoretic methods for far field sound radiation calculations

In the area of computational acoustics, procedures which accurately predict the far-field sound radiation are much sought after. A systematic development of such procedures are found in a sequence of papers by Atassi. The method presented here is an alternate approach to predicting far field sound based on simple layer potential theoretic methods. The main advantages of this method are: it requires only a simple free space Green's function, it can accommodate arbitrary shapes of Kirchoff surfaces, and is readily extendable to three-dimensional problems. Moreover, the procedure presented here, though tested for unsteady lifting airfoil problems, can easily be adapted to other areas of interest, such as jet noise radiation problems. Results are presented for lifting airfoil problems and comparisons are made with the results reported by Atassi. Direct comparisons are also made for the flat plate case.

Hariharan, S. I.↗

Interpretation of Solar Wind Ion Composition Measurements from Ulysses

The ion compositions measured in situ in the solar wind are important since the ion fractions carry information on the plasma conditions in the inner corona. The conditions in the inner corona define the properties of the solar wind plasma flow. Thus, if the ion fraction measurements can be used to unravel some of the plasma parameters in the inner corona, they will provide a valuable contribution to solving the heating and acceleration problem of the solar wind. The ion charge states in the solar wind carry information on electron temperature, electron density and ion flow speed. They are also sensitive to the shape of the electron distribution function. Through carefully modeling the solar wind and calculating the ion fractions predicted for different solar wind conditions, constraints on the electron temperature and ion flow speeds can be placed if the electron density is measured using polarization brightness measurements.

Esser, Ruth↗

Crash-Energy Absorbing Composite Structure and Method of Fabrication

A stand-alone, crash-energy absorbing structure and fabrication method are provided. A plurality of adjoining rigid cells are each constructed of resin-cured fiber reinforcement and are arranged in a geometric configuration. The geometric configuration of cells is integrated by means of continuous fibers wrapped thereabout in order to maintain the cells in the geometric configuration. The cured part results in a net shape, stable structure that can function on its own with no additional reinforcement and can withstand combined loading while crushing in a desired direction.

Kellas, Sotiris↗

Explosive Fracturing of an F-16 Canopy for Through-Canopy Crew Egress

Through-canopy crew egress, such as in the Harrier (AV-8B) aircraft, expands escape envelopes by reducing seat ejection delays in waiting for canopy jettison. Adverse aircraft attitude and reduced forward flight speed can further increase the times for canopy jettison. However, the advent of heavy, high-strength polycarbonate canopies for bird-strike resistance has not only increased jettison times, but has made seat penetration impossible. The goal of the effort described in this paper was to demonstrate a method of explosively fracturing the F-16 polycarbonate canopy to allow through-canopy crew ejection. The objectives of this effort were to: 1. Mount the explosive materials on the exterior of the canopy within the mold line, 2. Minimize visual obstructions, 3. Minimize internal debris on explosive activation, 4. Operate within less than 10 ms, 5. Maintain the shape of the canopy after functioning to prevent major pieces from entering the cockpit, and 6. Minimize the resistance of the canopy to seat penetration. All goals and objectives were met in a full-scale test demonstration. In addition to expanding crew escape envelopes, this canopy fracture approach offers the potential for reducing system complexity, weight and cost, while increasing overall reliability, compared to current canopy jettison approaches. To comply with International Traffic in Arms Regulations (ITAR) and permit public disclosure, this document addresses only the principles of explosive fracturing of the F-16 canopy materials and the end result. ITAR regulations restrict information on improving the performance of weapon systems. Therefore, details on the explosive loads and final assembly of this canopy fracture approach, necessary to assure functional performance, are not included.

Bement, Laurence J.↗

Use of Dual-wavelength Radar for Snow Parameter Estimates

Use of dual-wavelength radar, with properly chosen wavelengths, will significantly lessen the ambiguities in the retrieval of microphysical properties of hydrometeors. In this paper, a dual-wavelength algorithm is described to estimate the characteristic parameters of the snow size distributions. An analysis of the computational results, made at X and Ka bands (T-39 airborne radar) and at S and X bands (CP-2 ground-based radar), indicates that valid estimates of the median volume diameter of snow particles, D(sub 0), should be possible if one of the two wavelengths of the radar operates in the non-Rayleigh scattering region. However, the accuracy may be affected to some extent if the shape factors of the Gamma function used for describing the particle distribution are chosen far from the true values or if cloud water attenuation is significant. To examine the validity and accuracy of the dual-wavelength radar algorithms, the algorithms are applied to the data taken from the Convective and Precipitation-Electrification Experiment (CaPE) in 1991, in which the dual-wavelength airborne radar was coordinated with in situ aircraft particle observations and ground-based radar measurements. Having carefully co-registered the data obtained from the different platforms, the airborne radar-derived size distributions are then compared with the in-situ measurements and ground-based radar. Good agreement is found for these comparisons despite the uncertainties resulting from mismatches of the sample volumes among the different sensors as well as spatial and temporal offsets.

Liao, Liang↗

Global Gravity Wave Variances from Aura MLS: Characteristics and Interpretation

The gravity wave (GW)-resolving capabilities of 118-GHz saturated thermal radiances acquired throughout the stratosphere by the Microwave Limb Sounder (MLS) on the Aura satellite are investigated and initial results presented. Because the saturated (optically thick) radiances resolve GW perturbations from a given altitude at different horizontal locations, variances are evaluated at 12 pressure altitudes between 21 and 51 km using the 40 saturated radiances found at the bottom of each limb scan. Forward modeling simulations show that these variances are controlled mostly by GWs with vertical wavelengths z 5 km and horizontal along-track wavelengths of y 100-200 km. The tilted cigar-shaped three-dimensional weighting functions yield highly selective responses to GWs of high intrinsic frequency that propagate toward the instrument. The latter property is used to infer the net meridional component of GW propagation by differencing the variances acquired from ascending (A) and descending (D) orbits. Because of improved vertical resolution and sensitivity, Aura MLS GW variances are 5?8 times larger than those from the Upper Atmosphere Research Satellite (UARS) MLS. Like UARS MLS variances, monthly-mean Aura MLS variances in January and July 2005 are enhanced when local background wind speeds are large, due largely to GW visibility effects. Zonal asymmetries in variance maps reveal enhanced GW activity at high latitudes due to forcing by flow over major mountain ranges and at tropical and subtropical latitudes due to enhanced deep convective generation as inferred from contemporaneous MLS cloud-ice data. At 21-28-km altitude (heights not measured by the UARS MLS), GW variance in the tropics is systematically enhanced and shows clear variations with the phase of the quasi-biennial oscillation, in general agreement with GW temperature variances derived from radiosonde, rocketsonde, and limb-scan vertical profiles.

MLS (MICROWAVE LIMB SOUNDER)↗

Analysis-Driven Design Optimization of a SMA-Based Slat-Cove Filler for Aeroacoustic Noise Reduction

Airframe noise is a significant component of environmental noise in the vicinity of airports. The noise associated with the leading-edge slat of typical transport aircraft is a prominent source of airframe noise. Previous work suggests that a slat-cove filler (SCF) may be an effective noise treatment. Hence, development and optimization of a practical slat-cove-filler structure is a priority. The objectives of this work are to optimize the design of a functioning SCF which incorporates superelastic shape memory alloy (SMA) materials as flexures that permit the deformations involved in the configuration change. The goal of the optimization is to minimize the actuation force needed to retract the slat-SCF assembly while satisfying constraints on the maximum SMA stress and on the SCF deflection under static aerodynamic pressure loads, while also satisfying the condition that the SCF self-deploy during slat extension. A finite element analysis model based on a physical bench-top model is created in Abaqus such that automated iterative analysis of the design could be performed. In order to achieve an optimized design, several design variables associated with the current SCF configuration are considered, such as the thicknesses of SMA flexures and the dimensions of various components, SMA and conventional. Designs of experiment (DOE) are performed to investigate structural response to an aerodynamic pressure load and to slat retraction and deployment. DOE results are then used to inform the optimization process, which determines a design minimizing actuator forces while satisfying the required constraints.

Scholten, William↗

Track Structure and the Quality Factor for Space Radiation Cancer Risk

A major risk from exposure to space radiation is the induction of cancer and it is from estimates of this risk that the maximum career flight times of NASA space crew members are restricted by a permissible exposure limit. For the purpose of demonstrating compliance with the career limit, NASA has developed a cancer risk projection model for exposure-induced fatal cancer, in which the formulation and numerical values of the quality factor (QFNASA) are substantially different from those of the quality factor (Q) or radiation weighting factor (wR) routinely applied for radiation protection on earth. The quality factor is used to account for the increased effectiveness of radiations of high linear energy transfer (LET), compared to the effectiveness of low-LET γ-rays derived from epidemiological studies of the atomic-bomb survivors. The need for a special approach for space radiation is dictated by the special characteristics of the charged particles from solar radiation and especially the charged particles of high energy and charge (HZE) in galactic cosmic rays (GCR). This article considers aspects of radiation track structure in relation to the relative biological effectiveness (RBE) of HZE particles and the quality factor used for space radiation. The NASA quality factor (QFNASA) is composed of two terms, which can be interpreted as broadly representing the low- and the high-ionization-density components of the HZE particle tracks. These are discussed in turn as they relate to available experimental evidence on the biological effectiveness of such components. Also briefly described are subsequent published proposals for a reformulation of the quality factor to relate more directly to the acute γ-ray exposures from the atomic bombs and for further refinement of the parameter values (and their uncertainties) that determine the shape of the quality factor function. Other recent developments are also mentioned.

Mullenax, Carol A.↗

Preliminary Study of Heat Pipe Turbine Vane Cooling in the NASA N+3 Reference Engine

This paper investigates the effects of implementing Heat Pipe Turbine Vane (HPTV) cooling in the NASA N+3 engine. The HPTV can be thought of as a heat pipe in the shape of a turbine vane, functioning as both an aerodynamic body and heat exchanger. The heat-absorbing section of the HPTV remains fixed in the vanes of the high pressure turbine (HPT), while the heat-rejecting section can be placed in any stage of the low pressure turbine (LPT) as well as the bypass stream. The optimal location of the condensing (heat-rejecting) section is shown to be in the bypass stream for both HPT stages. The thrust specific fuel consumption increased by 0.2%, which is mainly attributed to the elimination of air cooling in the second stage HPT vanes combined with the transfer of energy from the main gas path to elsewhere in the cycle. Air cooling is also eliminated in the first stage HPT vanes, but this cooling air is nonchargeable. A preliminary design is proposed and shown to demonstrate the desired performance and operates below all the heat flux limitations in the first stage HPT . The design in the second stage HPT exceeds a limiting phenomenon but is expected to be remedied by changing the working fluid.

Gas Turbine↗

Preliminary Study of Heat Pipe Turbine Vane Cooling in the NASA N+3 Reference Engine

This investigates the effects of implementing Heat Pipe Turbine Vane (HPTV) cooling in the NASA N+3 engine. The HPTV can be thought of as a heat pipe in the shape of a turbine vane, functioning as both an aerodynamic body and heat exchanger. The heat-absorbing section of the HPTV remains fixed in the vanes of the high pressure turbine (HPT), while the heat-rejecting section can be placed in any stage of the low pressure turbine (LPT) as well as the bypass stream. The optimal location of the condensing (heat-rejecting) section is shown to be in the bypass stream for both HPT stages. The thrust specific fuel consumption increased by 0.2%, which is mainly attributed to the elimination of air cooling in the second stage HPT vanes combined with the transfer of energy from the main gas path to elsewhere in the cycle. Air cooling is also eliminated in the first stage HPT vanes, but this cooling air is nonchargeable. A preliminary design is proposed and shown to demonstrate the desired performance and operates below all the heat flux limitations in the first stage HPT . The design in the second stage HPT exceeds a limiting phenomenon but is expected to be remedied by changing the working fluid.

Gas Turbine↗

Bio-stasis: A Strategy for Survivability and Payload Cost Reduction in Long-duration Space Missions

As humans proceed with long-term space voyages, involving flights with lasting duration of months or years, “adaptation to space” will eventually lead to hard realities resultant physiological and psychological conditions must be realistically estimated and considered before it occurs. It is obvious that humans in their lifespan cannot adopt to spaceflight environment by reversible modification of their complex biochemical reactions and physiological functions without jeopardizing sustainable homeostasis shaped by multiple generations during evolution. In this case Nature offers an evolutionary proven alternative strategy- a coordinative adjustment of metabolism in order to survive. Incorporation of this metabolic adjustment strategy along with the relevant life support system into space flight architecture would protect humans during long term space flight from many irreversible physiological alterations and may dramatically reduce overall cost of space missions. In addition to the harmful space radiation and prolonged weightlessness, incorporation of this strategy may also benefit by solving other major medical unknowns in interplanetary flight such as isolation and psychological stress which still remains a risk. It is one of the priorities of NASA and other space agencies to figure out not only how to keep long-distance travelers alive and in good cognitive health but also how to return them to normal life on Earth with a minimum rehabilitation period after prolonged exposure to space. Presently re-adaptation of astronauts to Earth conditions and recovery from spaceflight exposure may take many months and years and, in some cases, require medical intervention. Therefore, recognizing physiological adjustment of the energy-regulating system as a viable life support strategy for human space exploration beyond LEO is essential.

Bio-stasis;↗

Tracing the Cosmic Energy Flow with Parker Solar Probe: Universal Processes

Heliophysics is inherently interdisciplinary, born from multiple subjects to understand how the Sun interacts with its surrounding environment. Heliophysicists and Astrophysicists seldom exchange ideas since the scientific infrastructure partitions research areas by spatial location in the cosmos. Parker Solar Probe (PSP) is sending back puzzling information in regions we have never been before, presenting an opportunity to search for answers in non-traditional ways that are inherently cross-disciplinary. The fundamental processes that govern the physics of the universe, such as wave-particle interactions, turbulence, magnetic reconnection, and shocks, are mechanisms to study cosmic energy flow. We present PSP observations that may enable us to assess the universality of these fundamental processes in – and across boundaries of –various space and astrophysical regimes. Specifically, we focus on the exotic shapes of proton velocity distribution functions and subsequent evolution leading to multi-scale wave generation and particle acceleration. We welcome ideas, tools, and methodologies from all disciplines to understand the systems of systems governing our universe.

J L Verniero↗

PREDICTION OF SURFACE SETTLEMENT DUE TO THE DISPLACEMENT OF SOFT ZONES

In areas composed of coastal plain sediments, soft zones subjected to partial overburden may be present in the subsurface. During or after a seismic event, these soft zones may be compressed. The resulting displacement due to the deformation of the soft zones will propagate to the ground surface and cause the surface to settle. This paper presents a method to predict the settlement at the surface due to the propagation of the displacement from the soft zones. This method is performed by discretizing the soft zones into multiple clusters of finite sub-areas or subspaces. Settlement profile at the ground surface due to the displacement of each sub-area or subspace is computed assuming the shape is a normal distribution function. Settlement due to the displacement of the soft zones can then be approximated by adding the settlements computed for all the sub-areas or subspaces. This method provides a simple and useful tool for the prediction of the settlement profile and the results are consistent with those obtained from the finite difference analysis.

58 GEOSCIENCES↗