Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermal diffusivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Transport properties of ions

The strong long-range interactions between (among) charged species require the inclusion of higher order contributions to the transport properties (viscosity, thermal conductivity, diffusion) of ionized gases than are required for neutral gases. These higher order contributions have been rewritten so that they are given in terms of universal functions which can be tabulated. Tables which provide for the rapid calculation of some higher order contributions to the transport properties of both ions and electrons are given. Some results which are useful for calculating the higher order contributions to the transport properties of mixtures of ions are also given. These results are applied to the ionic species in air at high temperatures.

Biolsi, Louis↗

Muon motion in titanium hydride

Motional narrowing of the transverse-field muon spin rotation signal was observed in gamma-TiH(x) for x = 1.83, 1.97, and 1.99. An analysis of the data for TiH1.99 near room temperature indicates that the mechanism responsible for the motion of the muon out of the octahedral site is thermally activated diffusion with an attempt frequency comparable to the optical vibrations of the lattice. Monte Carlo calculations to simulate the effect of muon and proton motion upon the muon field-correlation time were used to interpret the motional narrowing in TiH1.97 near 500 K. The interpretation is dependent upon whether the Bloembergen, Purcell, and Pound (BPP) theory or an independent spin-pair relaxation model is used to obtain the vacancy jump rate from proton NMR T1 measurements. Use of BPP theory shows that the field-correction time can be obtained if the rate of motion of the muon with respect to the rate of the motion for the protons is decreased. An independent spin-pair relaxation model indicates that the field-correlation time can be obtained if the rate of motion for the nearest-neighbor protons is decreased.

Kempton, J. R.↗

Vapor concentration measurement with photothermal deflectometry

Theoretical and experimental results for using the photothermal deflection technique to measure vapor species concentration, while minimizing the disturbance of the transport (material) parameters due to vapor heating, are developed and described. In contrast to common practice, the above constraints require using a pump-beam duty cycle of less than 50 percent. The theoretical description of the shortened heating time is based on a step-function formulation of the pumping cycle. The results are obtained as closed-form solutions of the energy equation for many chopping cycles until steady state is reached, by use of a Green's-function method. The Euler formulation of the Fermat principle is used to calculate the deflection angle. The equations are expanded to include the effects of vapor velocity on both the temperature and temperature gradient profiles. The effects of finite (unfocused) pump and probe beams and thermal (Soret) diffusion are also accounted for. Excellent agreement between theory and experiment is obtained.

Banish, R. Michael↗

A slow positron beam generator for lifetime studies

A slow positron beam generator using well-annealed polycrystalline tungsten moderators and a Na-22 positron source was developed. A 250 micro c source, deposited on a 2.54 micron thick aluminized mylar, is sandwiched between two (2.54 cm x 2.54 cm x 0.0127 cm) tungsten pieces. Two (2.54 cm x 2.54 cm x t cm) test polymer films insulate the two tungsten moderator pieces from the aluminized mylar source holder (t=0.00127 to 0.0127). A potential difference of 10 to 100 volts--depending on the test polymer film thickness (t)--is applied between the tungsten pieces and the source foil. Thermalized positrons diffusing out of the moderator pieces are attracted to the source foil held at an appropriate potential below the moderator pieces. These positrons have to pass through the test polymer films before they can reach the source foil. The potential difference between the moderator pieces and the aluminized mylar is so adjusted as to force the positrons to stop in the test polymer films. Thus the new generator becomes an effective source of positrons for assaying thin polymer films for their molecular morphology.

Singh, Jag J.↗

On the two-dimensional modelling of horizontal CVD reactors and its limitations

In order to clarify under what conditions two-dimensional theoretical models can realistically account for the actual growth rate distribution in horizontal CVD reactors, a systematic numerical study was performed, and the results were compared with published experimental data for the MOCVD of gallium arsenide. Three models of increasing complexity were studied. It is shown that two-dimensional models can produce realistic predictions only for reactors with large width-to-height (aspect) ratios, that are operated at subcritical Rayleigh number,i.e., under dominant forced flow conditions. But even then, depending on the carrier gas, thermal (Soret) diffusion must be included in the model. Furthermore, velocity corrections for finite aspect ratios must be made, and buoyancy effects can be significant in the entrance region. On the other hand, the results are relatively insensitive to axial diffusion, temperature dependence of transport properties (versus averaged properties), and an assumed Poiseuille velocity profile (versus a rigorous solution of the velocity field). Yet, boundary layer approximations are prone to give unrealistic results at the low Reynolds numbers typical for CVD operations.

Ouazzani, Jalil↗

Results of examination of silvered Teflon from the Long Duration Exposure Facility

A significant effort to determine the effects of low earth orbit (LEO) exposure on silver backed fluorinated ethylene-propylene (FEP) blankets from the Long Duration Exposure Facility (LDEF) was performed, and the results of this investigation are described. Extensive measurements of surface, optical, chemical, and mechanical properties were conducted. Effects of contamination and erosion rates of the FEP layer were determined. Specific results are reported on solar absorptance, thermal emittance, diffuse reflectance, cross sectional microphotography, secondary ion mass spectroscopy, electron scattering for chemical analysis, scanning electron microscopy, percent elongation, and tensile strength. These measurements show the effects of two distinctly different exposure environments, solar exposure, and simultaneous atomic oxygen (AO) and solar exposure.

Rousslang, Ken↗

Mass spectrometer use in a large chamber

The early satellites were somewhat insensitive to contamination produced during the construction and testing phases. The On-Orbit lifetime was such that contamination effects went either unnoticed or unrecognized. With today's On-Orbit lifetimes approaching 10+ years, contamination has become a paramount concern. The scientific payloads have increased in complexity and sensitivity. The ability to clean a contaminated sensor has greatly diminished. This requires better pumping systems and methods for improved monitoring. The conversion from diffusion pumped thermal vacuum chambers to cryo pumped chambers with the use of Misner traps and selective cold traps has reduced contamination. Witness samples supply a record of the condensates that remain after a testing cycle, but impart no knowledge of the contaminant migration during the cycle that may be a month in duration. Due to a customer's request that mass spectrometry be used during the testing of their spacecraft, a consultant was contracted to install a mass spectrometer to determine the feasibility of the instrument. The equipment and methodology described will start with the original system and its evolution to GE's present system.

Chuvala, Tom↗

Design, analysis, and fabrication of oxide-coated iridium/rhenium combustion chambers

Iridium-coated rhenium (Ir/Re) combustion chambers provide high temperature, oxidation-resistant operation for radiation-cooled liquid-fueled rocket engines. A 22-N (5-lb(sub f)) chamber has been operated for 15 hours at 2200 C (4000 F) using nitrogen tetroxide/monomethyl hydrazine (NTO/MMH) propellant, with negligible internal erosion. The oxidation resistance of these chambers could be further increased by the addition of refractory oxide coatings, providing longer life and/or operation in more oxidizing and higher temperature environments. The oxide coatings would serve as a thermal and diffusion barrier for the iridium coating, lowering the temperature of the iridium layer while also preventing the ingress of oxygen and egress of iridium oxides. This would serve to slow the failure mechanisms of Ir/Re chambers, namely the diffusion of rhenium to the inner surface and the oxidation of iridium. Such protection could extend chamber lifetimes by tens or perhaps hundreds of hours, and allow chamber operation on stoichiometric or higher mixture ratio oxygen/hydrogen (O2/H2) propellant. Extensive thermomechanical, thermochemical, and mass transport modeling was performed as a key material/structure design tool. Based on the results of these analyses, several 22-N oxide-coated Ir/Re chambers were fabricated and delivered to NASA Lewis Research Center for hot-fire testing.

Jang, Q.↗

A Balloon-Borne Cloud Condensation Nuclei Counter

A balloon-borne instrument was constructed for observations of vertical profiles of cloud condensation nucleus (CCN) concentrations, active at 1% supersaturation. Droplet concentration in the static thermal-gradient diffusion chamber is deduced from the amount of scattered laser light detected by a photodetector. The photodetector is calibrated using a video camera and computer system to count the number of droplets produced from NaCl aerosol. Preliminary data are available from nine early morning profiles obtained at Laramie, Wyoming, between June 1995 and January 1997. To complement the CCN measurements, instruments that measure condensation nuclei (CN) and aerosols with diameter greater than 0.30 micrometers (D(sub 0.3) were also included on the balloon package. CCN concentrations exhibited a general decrease from the surface to the top of the boundary layers, were generally uniform through well-mixed layers, and show variability above well-mixed layers. In general, the structure of the CCN profile appears to be closely related to the structure in the CN and D(sub 0.3) profiles. Summer profiles generally have CCN concentration greater than 200/cu cm up to 500 mbar, whereas winter profiles are less than 200/cu cm at all levels.

Delene, David J.↗

Mass Transfer Cooling Near The Stagnation Point

A simplified analysis is made of mass transfer cooling, that is, injection of a foreign gas, near the stagnation point for two-dimensional and axisymmetric bodies. The reduction in heat transfer is given in terms of the properties of the coolant gas and it is shown that the heat transfer may be reduced considerably by the introduction of a gas having appropriate thermal and diffusive properties. The mechanism by which heat transfer is reduced is discussed.

Roberts, Leonard↗

Modular Aquatic Simulation System 1D

MASS1 simulates open channel hydrodynamics and transport in branched channel networks, using cross-section averaged forms of the continuity, momentum, and convection diffusion equations. Thermal energy transport (temperature), including meteorological influences is supported. The thermodynamics of total dissolved gas (TDG) can be directly simulated. MASS1 has been developed over the last 20 years. It is currently being used on DOE projects that require MASS1 to beopen source. Hence, the authors would like to distribute MASS1 in source form.

Source record↗

Measurement techniques of thermoelectric devices and modules

Thermoelectric (TE) energy conversion devices are designed based on measured material transport properties. Although an ideal device efficiency can be calculated using the figure of merit, zT, the actual efficiency of a thermoelectric module is smaller and must be measured. TE device performance testing techniques and procedures are reviewed with a focus on energy conversion efficiency. One of the areas that attract less attention in the literature is the transition from basic thermoelectric materials research to the production of modules and devices. The effects of interface layers, diffusion barriers, thermal insulations, and heat sinks are reviewed. Finally, device performance from single couples to standard modules and long-term reliability are discussed.

Wang, Hsin↗

The Strategic Benefit of Self Shielded Boxes for Storage and Disposal of Metallic Uranic Material-18141

Sellafield Ltd, on behalf of the Nuclear Decommissioning Authority (NDA), is responsible for the management of a number of facilities whose inventories include a range of metallic uranic material. Additional fuel and fuel bearing materials exist in the NDA estate, some of which are similar to the Sellafield-managed inventory and others present different management challenges. Whilst UK Government policy directs that some of these materials are assets and are therefore managed with eventual future use in mind, there remains a large quantity of material, principally either out-of-scope for reprocessing or which derives from legacy facilities, which is likely to be disposed of to a future Geological Disposal Facility (GDF). The majority of this material is stored under wet conditions to facilitate dose shielding and heat dissipation and will therefore require removal from wet storage, consolidation and conditioning, prior to transfer to GDF. In order to accelerate high hazard and risk reduction by sooner retrieval of legacy material from wetted storage, one of the legacy storage facilities has led technical work to develop the design of Self Shielded Boxes (SSBs) and to substantiate their use for interim storage of the materials in question. Use of the SSBs would represent a change of strategy on the Sellafield Site: historically, timescales for retrieval of material have been reliant upon a waste treatment and storage/disposal route being available. SSBs provide the opportunity to retrieve uranic materials from aging legacy storage facilities for immediate buffer storage, by decoupling the timing of retrieval from the availability of an onward route. An understanding was required of the scope for defining optimal routes for each metallic uranic fuel and fuel bearing material group for safe transport and storage commensurate with current final disposal assumptions and risks, taking into account international best practice. A study is underway to understand options for transfer of material into SSBs, buffer/interim storage locations, treatment/conditioning processes and transport to the GDF. This work forms the basis of a prioritised road-map for the development of routes for study material groups aligned with ongoing and existing planned technical work, which is a pre-requisite to strategy development. The ultimate output of the study will be identification of full life cycle management strategies for metallic uranic material from an enterprise perspective. The combination of this strategic work and ongoing technical work will underpin a series of decisions to divert sub-groups of uranic material away from currently assumed baseline routes in support of earliest practicable hazard and risk reduction. Hence, each decision will reduce the scope of a placeholder future uranic fuel treatment capability, which will diminish the associated British Pound 1 bn capital cost. To date, a technical case for interim storage of uranic material in SSBs has been substantiated for around two thirds of the study materials. The requirement for a new strategy at Sellafield was driven by technical development of SSBs in response to the needs of one programme, but this prompted the study into the potential utilisation of SSBs in order to derive benefit for the wider enterprise and across the NDA estate. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Exploring the Use of Muon Momentum for Detection of Nuclear Material Within Shielded Spent Nuclear Fuel Dry Casks

The inspection of the storage containers that house used nuclear fuel is an important issue facing the nuclear industry; currently, there are limited options available to provide for even minimal inspections. During the long storage life of the fuel, intermediate handling and transportation activities may take place that can create concerns regarding fuel integrity (safety) and continuity of knowledge (safeguards and security). Accidents and natural disasters also contribute to this concern. The reliable and safe management of used nuclear fuel is among the critical tasks to be addressed for the advancement of fission-based nuclear energy in the United States and elsewhere. Since the early 1950's, when the first nuclear power plant began to produce electricity, approximately 65,000 metric tons of used nuclear fuel have been generated in the United States. The postponement of the opening of a permanent repository until 2048 will lead to increased used fuel accumulation at reactor sites. A rapid increase in storage installations with more than 9,000 casks storing {approx}420,000 assemblies is anticipated by 2050 even if no new nuclear power plants are built. After used nuclear fuel has been placed inside a cask, the cask is sealed, not allowing for visual inspection. Conventional methods, e.g., x-rays, are limited in that they cannot penetrate dense, well-shielded objects. More sophisticated techniques, such as penetrating neutrons or proton radiography, require the use of an expensive accelerator. Efforts by Ziock et al. using neutron and gamma-ray imagers concluded that '...the signatures are deemed insufficient to uniquely identify individual casks of the same type...'. It was found that the gamma-ray and neutron images were dominated by diffusion and thermalization effects resulting from the large amount of shielding. One promising mode of inspection would use cosmic-ray muons. These muons are naturally generated, are able to penetrate dense materials, and are incident from all directions above the horizon. Tomography performed using these muons could potentially provide efficient, inexpensive, remote assessment of used nuclear fuel. However, current muon applications are limited in that they have not included momentum measurement. If momentum measurement could be incorporated, that would represent a big step forward because it would allow more accurate estimation of the muon observables, e.g., scattering variance. This approach has the potential to reconstruct the contents of a cask with improved resolution and identify partial defects, fuel assemblies, and individual fuel rods.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Forced convection and transport effects during hyperbaric laser chemical vapor deposition

This work explores mass transport processes during HP-LCYD, including the transverse forced-flow of precursor gases through a nozzle to enhance fiber growth rates. The use of laser trapping and suspension of nano-scale particles in the precursor flow is also described, providing insights into the nature of the gas flow, including jetting from the fiber tip and thermodiffusion processes near the reaction zone. The effects of differing molecular-weight buffer gases is also explored in conjunction with the Soret effect, and it is found that nucleation at the deposit surface (and homogeneous nucleation in the gas phase) can be enhanced/ retarded, depending on the buffer gas molecular weight. To demonstrate that extensive microstructures can be grown simultaneously, three-dimensional fiber arrays are also grown in-parallel using diffractive optics--without delatory effects from neighboring reaction sites.

36 MATERIALS SCIENCE↗

Soot Deposit Properties in Practical Flames

Soot deposition from hydrocarbon flames was investigated in order to evaluate the evolution of the deposits during the transient process of heating an object that starts with a cold metal surface that is exposed to a flame. The study focused on the fire/metal surface interface and the critical issues associated with the specification of the thermal boundaries at this interface, which include the deposition of soot on the metal surface, the chemical and physical properties of the soot deposits and their subsequent effect on heat transfer to the metal surface. A laboratory-scale device (metallic plates attached to a water-cooled sampling probe) was designed for studying soot deposition in a laminar ethylene-air premixed flame. The metallic plates facilitate the evaluation of the deposition rates and deposit characteristics such as deposit thickness, bulk density, PAH content, deposit morphology, and thermal properties, under both water-cooled and uncooled conditions. Additionally, a non-intrusive Laser Flash Technique (in which the morphology of the deposit is not modified) was used to estimate experimental thermal conductivity values for soot deposits as a function of deposition temperature (water-cooled and uncooled experiments), location within the flame and chemical characteristics of the deposits. Important differences between water-cooled and uncooled surfaces were observed. Thermophoresis dominated the soot deposition process and enhanced higher deposition rates for the water-cooled experiments. Cooler surface temperatures resulted in the inclusion of increased amounts of condensable hydrocarbons in the soot deposit. The greater presence of condensable material promoted decreased deposit thicknesses, larger deposit densities, different deposit morphologies, and higher thermal conductivities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗