Search NASA⌕ Search

SEARCH · Search NASA

Results for “wind engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Investigation of Innovative Rotor Concepts for the Big Adaptive Rotor Project

The Big Adaptive Rotor (BAR) project is funded by the U.S. Department of Energy (DOE) Wind Energy Technologies Office and has the objective of researching and developing innovative technologies that enable large land-based rotors that have the potential to produce a 10% increase in CF over current technology. The innovative technologies must have a reduction in specific power to at least 150 W/m2 at an International Electrotechnical Commission Class III wind site for a 5-megawatt (MW) or higher rating and maintain a competitive levelized cost of energy (LCOE) compared to current technology. The purpose of this document is to: 1. Identify and classify innovative BAR concepts, 2. Evaluate the concepts in terms of their potential to impact wind plant LCOE and other performance metrics of interest and identify science and engineering challenges that would limit the commercialization of these concepts, and 3. Quantitatively analyze and compare the BAR concepts.

17 WIND ENERGY↗

Reduction of aerodynamic drag and fuel consumption for tractor-trailer vehicles

Wind-tunnel tests were performed on a scale model of a cab-over-engine tractor-trailer vehicle and several modifications of the model. Results from two of the model configurations were compared with full-scale drag data obtained from similar configurations during coast-down tests. Reductions in fuel consumption derived from these tests are presented in terms of fuel quantity and dollar savings per vehicle year, based on an annual driving distance of 160,900 km (100,000 mi.). The projected savings varied from 13,001 (3435) to 25,848 (6829) liters (gallons) per year which translated to economic savings from $3435 to about $6829 per vehicle year for an operating speed of 88.5 km/h (55 mph) and wind speeds near the national average of 15.3 km/h (9.5 mph). The estimated cumulative fuel savings for the entire U.S. fleet of cab-over-engine tractor, van-type trailer combinations ranged from 4.18 million kl (26.3 million bbl) per year for a low-drag configuration to approximately twice that amount for a more advanced configuration.

Muirhead, V. U.↗

NREL Computer Models Integrate Wind Turbines with Floating Platforms (Fact Sheet)

Far off the shores of energy-hungry coastal cities, powerful winds blow over the open ocean, where the water is too deep for today's seabed-mounted offshore wind turbines. For the United States to tap into these vast offshore wind energy resources, wind turbines must be mounted on floating platforms to be cost effective. Researchers at the National Renewable Energy Laboratory (NREL) aresupporting that development with computer models that allow detailed analyses of such floating wind turbines.

17 WIND ENERGY↗

Stochastic Models, Indices & Optimization Algorithms for Pricing & Hedging Reliability Risks in Modern Power Grids: Data Plan - Princeton

We collected and cleaned the synthetic grid data produced by NREL for the Texas and New York synthetic grids. We developed a high dimensional joint stochastic model for load at the zone level, and solar and wind power productions at the asset level, capturing the spatial and temporal dependencies between all the variables, and demonstrated how such a model could be fitted to historical data. We designed and implemented a simulation engine which can produce Monte Carlo scenarios for the hourly day-ahead values of load, and solar and wind power productions at the spatial and temporal resolutions of the historical data used to fit the model. Finally we developed an open-source Python package which can, from an input grid model, efficiently use forecasts and large numbers of Monte Carlo scenarios to provide unit commitment and economic dispatch for each of these scenarios. The high dimensional stochastic model and the subsequent Monte Carlo simulation engine were implemented in the package PGscen and the corresponding UC and ED optimization programs in the package Vatic.

14 SOLAR ENERGY↗

LORENTZ-FACTOR-ISOTROPIC-LUMINOSITY/ENERGY CORRELATIONS OF GAMMA-RAY BURSTS AND THEIR INTERPRETATION

The bulk Lorentz factor of the gamma-ray burst (GRB) ejecta ({Gamma}{sub 0}) is a key parameter to understanding GRB physics. Liang et al. have discovered a correlation between {Gamma}{sub 0} and isotropic {gamma}-ray energy: {Gamma}{sub 0}{proportional_to}E{sup 0.25}{sub {gamma},iso,52}. By including more GRBs with updated data and more methods to derive {Gamma}{sub 0}, we confirm this correlation and obtain {Gamma}{sub 0} {approx_equal} 91E{sup 0.29}{sub {gamma},iso,52}. Evaluating the mean isotropic {gamma}-ray luminosities L{sub {gamma},iso} of the GRBs in the same sample, we discover an even tighter correlation {Gamma}{sub 0} {approx_equal} 249L{sup 0.30}{sub {gamma},iso,52}. We propose an interpretation to this later correlation. Invoking a neutrino-cooled hyperaccretion disk around a stellar mass black hole as the central engine of GRBs, we derive jet luminosity powered by neutrino annihilation and baryon loading from a neutrino-driven wind. Applying beaming correction, we finally derive {Gamma}{sub 0}{proportional_to}L{sup 0.22}{sub {gamma},iso}, which is consistent with the data. This suggests that the central engine of long GRBs is likely a stellar mass black hole surrounded by a hyper-accreting disk.

79 ASTRONOMY AND ASTROPHYSICS↗

Assessing the Importance of Nonlinearities in the Development of a Substructure Model for the Wind Turbine CAE Tool FAST: Preprint

Design and analysis of wind turbines are performed using aero-servo-elastic tools that account for the nonlinear coupling between aerodynamics, controls, and structural response. The NREL-developed computer-aided engineering (CAE) tool FAST also resolves the hydrodynamics of fixed-bottom structures and floating platforms for offshore wind applications. This paper outlines the implementation of a structural-dynamics module (SubDyn) for offshore wind turbines with space-frame substructures into the current FAST framework, and focuses on the initial assessment of the importance of structural nonlinearities. Nonlinear effects include: large displacements, axial shortening due to bending, cross-sectional transverse shear effects, etc.

17 WIND ENERGY↗

Static and Wind Tunnel Aero-Performance Tests of NASA AST Separate Flow Nozzle Noise Reduction Configurations

This report presents the results of cold flow model tests to determine the static and wind tunnel performance of several NASA AST separate flow nozzle noise reduction configurations. The tests were conducted by Aero Systems Engineering, Inc., for NASA Glenn Research Center. The tests were performed in the Channels 14 and 6 static thrust stands and the Channel 10 transonic wind tunnel at the FluiDyne Aerodynamics Laboratory in Plymouth, Minnesota. Facility checkout tests were made using standard ASME long-radius metering nozzles. These tests demonstrated facility data accuracy at flow conditions similar to the model tests. Channel 14 static tests reported here consisted of 21 ASME nozzle facility checkout tests and 57 static model performance tests (including 22 at no charge). Fan nozzle pressure ratio varied from 1.4 to 2.0, and fan to core total pressure ratio varied from 1.0 to 1.19. Core to fan total temperature ratio was 1.0. Channel 10 wind tunnel tests consisted of 15 tests at Mach number 0.28 and 31 tests at Mach 0.8. The sting was checked out statically in Channel 6 before the wind tunnel tests. In the Channel 6 facility, 12 ASME nozzle data points were taken and 7 model data points were taken. In the wind tunnel, fan nozzle pressure ratio varied from 1.73 to 2.8, and fan to core total pressure ratio varied from 1.0 to 1.19. Core to fan total temperature ratio was 1.0. Test results include thrust coefficients, thrust vector angle, core and fan nozzle discharge coefficients, total pressure and temperature charging station profiles, and boat-tail static pressure distributions in the wind tunnel.

Mikkelsen, Kevin L.↗

Laser Rayleigh Scattering for Flow Density and Condensation Measurements in the Supercooled Mach-14 Free-Stream at AEDC Wind Tunnel No. 9

Laser Rayleigh scattering was used to investigate clusters in the free-stream flow at Arnold Engineering Development Center’s Tunnel 9 (T9). The facility was run at Mach-14, with a pure-N2 flow medium, and at several total pressures and temperatures. Using an excimer laser operating at 248 nm, the Rayleigh instrument imaged scattering from the focused laser beam in the free-stream. As a wind-tunnel flow is accelerated, it cools and approaches the condensation boundary. As a precursor to condensation, small clusters of molecules are first formed, but the individual clusters are too small to be spatially resolved in typical images of the beam. Thus clusters effectively add a spatially smooth background signal to the pure diatomic-molecule Rayleigh signal. The main result of the present work is that clustering was not significant. After correcting for interference by small particles imbedded in the T9 flow, cluster scattering was unobservable or smaller than one standard deviation (1-sigma) of the uncertainties for almost all tunnel runs. The total light scattering level was measured to be 1.05 +/- 0.15 (1-sigma) of the expected diatomic scattering, when averaged over the entire usable data set. This result included flow conditions that were supercooled to temperatures of ~ 20 K, about 25 K below the condensation limit of ~ 45 K. Thus the Mach-14 nozzle flow is essentially cluster-free for many supercooled conditions that might be used to extend the facility operating range to larger Reynolds numbers.

Herring, Gregory C.↗

Comparison of ground and flight test results using a modified F106B aircraft

Two aft underwing nacelles housing afterburning J85 engines were added to an F106 to study exhaust nozzles in flight at Mach numbers up to 1.3. Installation effects were determined for several nozzles by comparing flight data to data from an isolated wind tunnel model. Reynolds number effects were studied at subsonic flight speeds for nozzles intended for use with afterburning turbofan engines. A wide range of Reynolds number was obtained by flying the F106 over a range of altitude and by using 5 and 22% wind tunnel models of the F106. A contoured nozzle had a boattail drag as low as that of a longer circular arc nozzle over the Reynolds number range studied.

Wilcox, F. A.↗

Comparison of heating rate calculations with experimental data on a modified Shuttle orbiter at Mach 6

Heating-rate calculations from an 'engineering' code and a 'benchmark' Navier-Stokes code are compared with experimental wind tunnel data obtained on a 'modified' 0.0075-scale Shuttle orbiter at a Mach number of 6 and a freestream Reynolds number of 1.9 x 10 to the 6th/m. Comparisons are presented along the windward symmetry plane, in a circumferential direction around the body, and along the wing leading edge at angles of attack of 30 and 40 deg. Both codes provide accurate predictions of the heating rate over most of the body, but because the run time for the engineering code is relatively short, it is an ideal tool for both parametric and design studies.

Hamilton, H. H., II↗

Hypersonic research engine project. Phase 2: Structures and cooling development

The structures assembly model (SAM) was installed, and wind tunnel systems were checked out. The first run, with hydrogen cooling and SAM inserted in the wind tunnel stream (M = 7.7, P sub TOTAL = 900 psia, T sub TOTAL = 2500 deg R), was accomplished. The condition of the SAM after the run was satisfactory, with no visible signs or data indications of overheating or overloading.

Jilly, L. F.↗

Full-scale aerodynamic characteristics of a propellar installed on a small twin-engine aircraft wing panel

Full-scale measurements of shaft thrust and torque were made. Wind-tunnel speeds and blade angles were set for full-scale flight conditions. Excellent quality measurements were obtained of the thrust coefficient, the power coefficient, and the propeller efficiency for various values of the advance ratio and the blade incidence angle at 3/4-blade radius. A conventional propeller theory found in the literature was applied to the present results. Although thrust, power, and efficiency were somewhat overpredicted, the advance ratio for maximum efficiency was predicted quite accurately. It was found that, for some conditions, spinner drag could be significant. A simple correction that was based on the spinner base pressure substantially accounted for the changes in efficiency that resulted from this cause.

Barlow, P. R.↗

Global Reference Atmospheric Model (GRAM) Advancements and Additions

Introduction:The Global Reference Atmospheric Model (GRAM) is one of the most widely used engineering models of the atmosphere. GRAM development and maintenance has been led by NASA Marshall Space Flight Center (MSFC). The NASA Science Mission Directorate (SMD) has provided funding support to upgrade the GRAMs since Fiscal Year 2018. NASA Langley Research Center has been working with MSFC on the upgrades.This presentation will provide details regarding the upgrades that have been made to the existing GRAMs, the development of new GRAMs, as well as the ongoing objectives, tasks, and milestones re-lated to the GRAM upgrades funded by NASA SMD. GRAM: The GRAMs are engineering-oriented atmospheric models that estimate mean values and statistical variations of the atmospheric properties for numerous planetary destinations.They provide mean values and variability for any point in the atmosphere as well as seasonal, geographic, and altitude variations. GRAM outputs include atmospheric density, temperature, pressure, winds, and chemical composition along a user-defined path.Theyhave been widely used by the engineering community because of their ability to create realistic dispersions. GRAMs have been integrated into high fidelity flight dynamic simulations of launch, entry, descent and landing (EDL), aerobraking and aerocapture. MSFC has been developing and updating GRAMs since 1974; GRAMs are currently available for Earth, Mars, Venus, Neptune, and Titan. GRAM Upgrade Status: Code Moderization.The planetary GRAMs are being rearchitected from Fortran to a common object-ori-entedC++ framework called the GRAM Suite. This new architecture creates a common GRAM library of data models and utilities. The first C++ releases of the existing planetary GRAMs (Mars, Venus, Neptune, and Titan-GRAM) in the GRAM Suite are straight conversions from the latest Fortran version. Model Upgrades.The focus of the model upgrade task is to improve the atmosphere models in the existing GRAMs and to establish a foundation for developing GRAMs for additional destinations. The GRAM ephemerishas been upgraded to the NASA Navigation and Ancillary Information Facility (NAIF) SPICE toolkit (version N0066). The calculation of the speed of sound has also been improved in the GRAMs. The GRAM team has received updated Mars General Circulation Model (MGCM) datasets from NASA Ames Research Center. Mars Global Ionosphere-Thermosphere Model (M-GITM) data is being obtained toreplace the Mars Thermospheric General Circulation Model (MTGCM) data in legacy Mars-GRAM. M-GITM and updated MGCM data will be incorporated into a future GRAM Suite release.Twoprojects that will improve the atmospheric model data in the GRAMs have been funded by the GRAM team since Fiscal Year 2020. Sanjay Limaye and Patrick Fry at the University of Wisconsin are reanalyzing the Venus Express radio occultation observations and analyzing the Akatsukiradio occultation observations.This will lead tothe calculation of number density, temperature, and pressure profiles for the 40-90 km altitude range. Kunio Sayanagi, Justin Garland, and Ryan McCabeat Hampton University are developing empirical global models for Venus,Jupiter, Saturn, Uranus, Neptune, and Titan that incorporates the latest data available for each of these planetary destinations. Upgraded GRAM Releases. GRAM Suite Version 1.0 was released in May 2020 and contains the rearchitected Neptune-GRAM, including the common GRAM framework and planet–specific code. GRAM Suite Version 1.1 was released in September 2020 and addedthe rearchitected Titan-GRAM to the GRAM Suite. A User Guide and Programmer’s Manualarereleased with all GRAMs. The rearchitected Mars and Venus-GRAMs will be released in upcomingversions of the GRAM Suite. New GRAM Releases. New GRAMs have been de-veloped for Uranus and Jupiter. Uranus-GRAM is based on an individual profile generated by Gary Allen (ARC) from Voyager 2 occultation data and will be released in GRAM Suite Version 1.2. Jupiter-GRAM is based on individual profile produced from Al Seiff’s Ju-piter model[1].Jupiter-GRAM will be released in GRAM Suite Version 1.3. Saturn-GRAM is currently under development and will be released in a future version of the GRAM Suite. Conclusions: GRAMs are vital and frequently used toolsets. Releases of the GRAM Suite, upgrades of the existing planetary GRAMs, and development of new planetary GRAMs are ongoing. NASA SMD funding has been essential to addressing current limitations and accomplishing GRAM developmental goals. Continua-tion ofSMD fundingwill ensure the development, up-grades, and maintenance of the GRAMs. References: [1] Seiff, A., et al. (1998) JGR, 103, 22,857-22,889. Acknowledgments: The authors gratefully acknowledge support from the NASA SMD

atmospheric models↗

Centrifuge modeling and numerical analysis on lateral performance of mono-bucket foundation for offshore wind turbines

The lateral loading performance of the mono-bucket foundation for offshore wind turbines is investigated in this study through a series of centrifuge tests and numerical analysis. Six mono-bucket models are considered to assess the influences of aspect ratio under the ultimate condition. The FE model is validated against the centrifuge test results, and the failure mechanism of the foundation is revealed. The parametric study and sensitivity analysis of the soil parameters are performed in the numerical simulations. A modified theoretical calculation method is proposed to estimate the ultimate lateral capacity of the suction bucket foundation by solving the limit equilibrium equations. A correction term is added in the calculation using the “m” method. The position of the rotation center is calculated, demonstrating a better accuracy compared to the previously reported geometric method. The modified calculation method is verified against the field test, the centrifuge test, and the laboratory test. The method is proved to be applicable in estimating the lateral performance of the mono-bucket foundation in a general form. Finally, this study aims to provide well-documented data and design references for practical engineers.

17 WIND ENERGY↗

Simulation investigation of the effect of the NASA Ames 80-by 120-foot wind tunnel exhaust flow on light aircraft operating in the Moffett field trafffic pattern

A preliminary study of the exhaust flow from the Ames Research Center 80 by 120 Foot Wind Tunnel indicated that the flow might pose a hazard to low-flying light aircraft operating in the Moffett Field traffic pattern. A more extensive evaluation of the potential hazard was undertaken using a fixed-base, piloted simulation of a light, twin-engine, general-aviation aircraft. The simulated aircraft was flown through a model of the wind tunnel exhaust by pilots of varying experience levels to develop a data base of aircraft and pilot reactions. It is shown that a light aircraft would be subjected to a severe disturbance which, depending upon entry condition and pilot reaction, could result in a low-altitude stall or cause damage to the aircraft tail structure.

Streeter, Barry G.↗

Global Reference Atmospheric Model and Trace Constituents

Global Reference Atmospheric Model (GRAM-99) is an engineering-level model of the Earth's atmosphere. It provides both mean values and perturbations for density, temperature, pressure, and winds, as well as monthly- and geographically-varying trace constituent concentrations. From 0-27 km, thermodynamics and winds are based on National Oceanic and Atmospheric Administration Global Upper Air Climatic Atlas (GUACA) climatology. Above 120 km, GRAM is based on the NASA Marshall Engineering Thermosphere (MET) model. In the intervening altitude region, GRAM is based on Middle Atmosphere Program (MAP) climatology that also forms the basis of the 1986 COSPAR Intemationa1 Reference Atmosphere (CIRA). MAP data in GRAM are augmented by a specially-derived longitude variation climatology. Atmospheric composition is represented in GRAM by concentrations of both major and minor species. Above 120 km, MET provides concentration values for N2, O2, Ar, O, He, and H. Below 120 km, species represented also include H2O, O3, N2O, CO, CH, and CO2. Water vapor in GRAM is based on a combination of GUACA, Air Force Geophysics Laboratory (AFGL), and NASA Langley Research Center climatologies. Other constituents below 120 km are based on a combination of AFGL and h4AP/CIRA climatologies. This report presents results of comparisons between GRAM Constituent concentrations and those provided by the Naval Research Laboratory (NRL) climatology of Summers (NRL,/MR/7641-93-7416, 1993). GRAM and NRL concentrations were compared for seven species (CH4, CO, CO2, H2O, N2O, O2, and O3) for months January, April, July, and October, over height range 0-115 km, and latitudes -90deg to + 90deg at 10deg increments. Average GRAM-NRL correlations range from 0.878 (for CO) to 0.975 (for O3), with an average over all seven species of 0.936 (standard deviation 0.049).

Justus, C.↗

Lewis Structures Technology, 1988. Volume 3: Structural Integrity Fatigue and Fracture Wind Turbines HOST

The charter of the Structures Division is to perform and disseminate results of research conducted in support of aerospace engine structures. These results have a wide range of applicability to practioners of structural engineering mechanics beyond the aerospace arena. The specific purpose of the symposium was to familiarize the engineering structures community with the depth and range of research performed by the division and its academic and industrial partners. Sessions covered vibration control, fracture mechanics, ceramic component reliability, parallel computing, nondestructive evaluation, constitutive models and experimental capabilities, dynamic systems, fatigue and damage, wind turbines, hot section technology (HOST), aeroelasticity, structural mechanics codes, computational methods for dynamics, structural optimization, and applications of structural dynamics, and structural mechanics computer codes.

Source record↗