Search NASA⌕ Search

SEARCH · Search NASA

Results for “FAILURE MODES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Finite Element Modeling of the Phase Change in Thermally-Grown SiO 2 in SiC Systems for Gas Turbines

The operating lifetimes of SiC-based components in combustion environments are directly linked to the adhesion of the protective environmental barrier coating (EBC) layer. One of the major known failure modes for EBCs is the formation of a thick SiO 2 thermally grown oxide (TGO), which decreases coating adhesion and encourages eventual coating spallation. The effect of the TGO thickness under Yb 2 Si 2 O 7 EBCs on silicon carbide was investigated using finite element models (FEMs) with various interfacial architectures and SiO 2 TGO thicknesses. Further, the FEMs incorporated a user-defined material to simulate the volume contraction of the TGO during the silica phase transformation from β-cristobalite to α-cristobalite upon cooling from the stress-free state at 1350°C to room temperature. Systems with and without a silicon bond coating intermediary layer were assessed. It was shown that the TGO phase transformation stress (1.6–1.7 GPa) dominated the increase in stress in the TGO and EBC layers. Furthermore, it was found that stress increase in the TGO was independent of TGO thickness and interface geometry. These results indicate that stabilization of the TGO to mitigate the phase transformation could dramatically improve the performance of SiC-base components with EBCs.

36 MATERIALS SCIENCE↗

Joint strength in high speed friction stir spot welded DP 980 steel

High speed friction stir spot welding was applied to 1.2 mm thick DP 980 steel sheets under different welding conditions, using PCBN tools. The range of vertical feed rates used during welding was 2.5 mm – 102 mm per minute, while the range of spindle speeds was 2500 – 6000 rpm. Extended testing was carried out for five different sets of welding conditions, until tool failure. These welding conditions resulted in vertical welding loads of 3.6 – 8.2 kN and lap shear tension failure loads of 8.9 – 11.1 kN. PCBN tools were shown, in the best case, to provide lap shear tension fracture loads at or above 9 kN for 900 spot welds, after which tool failure caused a rapid drop in joint strength. Joint strength was shown to be strongly correlated to bond area, which was measured from weld cross sections. Failure modes of the tested joints were a function of bond area and softening that occurred in the heat-affected zone.

DP980↗

Effect of Topology on Transient Dynamic and Shock Response of Polymeric Lattice Structures

Architected cellular materials, such as lattice structures, offer potential for tunable mechanical properties for dynamic applications of energy absorption and impact mitigation. In this work, the static and dynamic behavior of polymeric lattice structures was investigated through experiments on octet-truss, Kelvin, and cubic topologies with relative densities around 8%. Here, dynamic testing was conducted via direct impact experiments (25–70 m/s) with high-speed imaging coupled with digital image correlation and a polycarbonate Hopkinson pressure bar. Mechanical properties such as elastic wave speed, deformation modes, failure properties, particle velocities, and stress histories were extracted from experimental results. At low impact velocities, a transient dynamic response was observed which was composed of a compaction front initiating at the impact surface and additional deformation bands whose characteristics matched low strain-rate behavior. For higher impact velocities, shock analysis was carried out using compaction wave velocity and Eulerian Rankine–Hugoniot jump conditions with parameters determined from full-field measurements.

36 MATERIALS SCIENCE↗

Fabrication, structure and mechanical properties of indium nanopillars

Solid and hollow cylindrical indium pillars with nanoscale diameters were prepared using electron beam lithography followed by the electroplating fabrication method. The microstructure of the solid-core indium pillars was characterized by scanning micro-X-ray diffraction, which shows that the indium pillars were annealed at room temperature with very few dislocations remaining in the samples. The mechanical properties of the solid pillars were characterized using a uniaxial microcompression technique, which demonstrated that the engineering yield stress is {approx}9 times greater than bulk and is {approx}1/28 of the indium shear modulus, suggesting that the attained stresses are close to theoretical strength. Microcompression of hollow indium nanopillars showed evidence of brittle fracture. This may suggest that the failure mode for one of the most ductile metals can become brittle when the feature size is sufficiently small.

36 MATERIALS SCIENCE↗

Experimental tests of stereological estimates of grain boundary populations

We present experimental validation of a method for estimating three-dimensional (3-D) relative numerical populations of grain boundaries from measurements of individual two-dimensional (2-D) cross-sections. Such numerical populations are relevant to network topology and the modeling of intergranular failure modes in grain boundary engineered materials, and are distinct from geometrical population measures such as area per volume. We examine 3-D reconstructions of stainless steel and copper, with varying populations of twin-related boundaries, generated by serial-section electron backscatter diffraction and high-energy X-ray diffraction microscopy. We show that 2-D length fractions, 2-D number fractions and 3-D number fractions are all distinct quantities when grain boundary type is correlated with grain boundary size. We also demonstrate that the last quantity may be reliably inferred from the first two, provided the experimental spatial resolution is much finer than the grain size, eliminating the need to use 3-D experimental methods to access at least some information about 3-D network properties. Many of the {Sigma}3 boundaries are extremely complex, with highly re-entrant shapes that can intersect a sample plane many times, giving a false impression of multiple separate boundaries.

36 MATERIALS SCIENCE↗

Mapping local deformation behavior in single cell metal lattice structures

The deformation behavior of metal lattice structures is extremely complex and challenging to predict, especially since strain is not uniformly distributed throughout the structure. Understanding and predicting the failure behavior for these types of light-weighting structures is of great interest due to the excellent scaling of stiffness- and strength-to weight ratios they display. Therefore, there is a need to perform simplified experiments that probe unit cell mechanisms. This study reports on high resolution mapping of the heterogeneous structural response of single unit cells to the macro-scale loading condition. Two types of structures, known to show different stress-strain responses, were evaluated using synchrotron radiation micro-tomography while performing in-situ uniaxial compression tests to capture the local micro-strain deformation. These structures included the octet-truss, a stretch-dominated lattice, and the rhombic-dodecahedron, a bend-dominated lattice. The tomographic analysis showed that the stretch- and bend-dominated lattices exhibit different failure mechanisms and that the defects built into the structure cause a heterogeneous localized deformation response. Also shown here is a change in failure mode for stretch-dominated lattices, where there appears to be a transition from buckling to plastic yielding for samples with a relative density between 10 and 20%. In conclusion, the experimental results were also used to inform computational studies designed to predict the mesoscale deformation behavior of lattice structures. Here an equivalent continuum model and a finite element model were used to predict both local strain fields and mechanical behavior of lattices with different topologies.

36 MATERIALS SCIENCE↗

High compressive energy absorption and shape recovery behavior of additively manufactured textile-inspired cylindrical braided metamaterials

Mechanical metamaterials (MMs) are engineered structures with unique mechanical properties that arise from their unique spatial arrangement or lattice-like structure. The most commonly designed MMs such as honeycomb and re-entrant auxetics are prone to failure at the sharp corners and weak joints due to the increased stress concentration under deformation. To mitigate this challenge, braided MM structures involving intertwining threads of nylon—forming curved unit cells—have been studied. These textile-inspired cylindrical braided metamaterials (CBMMs) with contrasting unit cells, namely diamond and regular CBMMs, were fabricated by 3D printing. The layer-by-layer deposited structure built by fused filament fabrication delivered an assembly of overlapped threads that are fused at the contact point. To understand deformation behavior of these MMs, finite element models were developed for various load scenarios including quasi-static compression, cyclic and creep loads at room temperature. Stress distribution, deformation mechanisms, and failure modes were analyzed and validated by experiments to analyze the geometries and associated performance. The diamond CBMMs showed stress softening at 30 % compressive strain, withstanding a load of ∼440 N, whereas the regular CBMMs at 50 % strain experienced ∼250 N. The diamond CBMMs delivered higher creep resistance under sustained load and better energy absorption under cyclic loading than the regular CBMMs. The latter, however, exhibited 94 % shape recovery in contrast to 88 % recovery in former prototype during their first cyclic load. In conclusion, this study helps design mechanical lightweight devices that endure significant sustained load and exhibit enhanced energy absorption and shape recovery characteristics in cyclic loading.

Creep↗

Influence of fiber inclination angle on bond-slip behavior of different alkali-activated composites under dynamic and quasi-static loadings

This study investigates the influence of inclination angle (0° and 45°) on the interfacial bond-slip behavior of macro steel fibers (straight, hooked end-deformed and length-deformed) and length-deformed polypropylene fibers reinforced in fly-ash and metakaolin based alkali-activated composites (AACs) under quasi-static and dynamic loadings. AACs demonstrate superior peak bond strength and toughness compared to cement composites regardless of fiber type and loading rate. Results also show that straight steel fiber exhibits a complete pullout in AACs. The amount of deformation of the fibers (deformation ratio) determined the failure type at different inclination angle and loading rate, thus governing the peak load and energy absorption. Depending on the fiber orientation, premature fiber rupture or matrix cracking is observed under dynamic loading in AACs due to matrix brittleness. The fiber failure modes in dynamic pullout are no different from those observed in the quasi-static pullout in AACs.

36 MATERIALS SCIENCE↗

DEM analysis of the effect of interface transition zone on dynamic splitting tensile behavior of high-strength concrete based on multi-phase model

Highlights: • Crushable aggregates with the real geometry shape are generated by using clump-cluster method. • Flat-Joint Model is adopted as the constitutive law. • The tensile strength is almost not affected by ITZ strength when its strength exceeds 0.8 times that of mortar. • A modified formula that can reflect the functional relationship between the ITZ strength and the TDIF is proposed. The tensile strength is one of the main parameters in the design of concrete structures and has an important influence on the cracking performance and durability of concrete materials. As the weak region in concrete, the strength of the interface transition zone (ITZ) directly affects the dynamic mechanical response of concrete. Meanwhile, considering that the tensile performance of concrete is far weaker than its compressive performance, the study of the strength of ITZ is of great significance to the dynamic tensile fracture characteristics and mechanical properties of concrete. In this paper, a method combining 3D scanning technology and Clump-Cluster was proposed to generate a real geometry shape model of crushable aggregate. On this basis, the 3D discrete element model (DEM) of high-strength concrete was constructed using the Flat-Joint Model (FJM). The effects of the ITZ strength on the failure mode, number of microcracks, tensile strength and strain rate effect of high-strength concrete under strain rates from 0.01/s to 100/s were studied by splitting tensile test. The simulation results indicate that the number of microcracks generated decreases with the increase of ITZ strength, and the proportion of ITZ cracks decreases obviously. When the ITZ strength exceeds the critical value of 0.8 times that of mortar, the tensile strength is almost not affected by ITZ strength. In addition, based on the numerical simulation results, a modified formula that can reflect the functional relationship between the ITZ strength and the dynamic increasing factor of the concrete tensile strength (TDIF) is proposed, and the rationality of the TDIF modified formula is verified.

36 MATERIALS SCIENCE↗

Predicting Tensile Stretchability of Trimmed AA6111-T4 Sheets

An integrated manufacturing process simulation framework has been developed to predict the trimmed edge tensile stretchability of AA6111-T4 sheets by incorporating the burr geometry, damage, and plastic strain from trimming simulations into subsequent tensile stretchability simulations. The influence of the trimming die clearances on the predicted tensile stretching ductility (stretchability) is studied and quantitatively compared with experimental measurements. Stretchability is found to decrease with increasing cutting clearances, and simulation results have successfully captured experimentally observed edge crack initiation and failure mode variations for different trimming clearances. Subsequent computational sensitivity studies reveal that while deburring of previously trimmed edges has little influence on tensile stretchability, removal of trimmed edge initial plastic strain may significantly enhance the subsequent trimmed edge stretchability.

Aluminum alloys↗

Discrete element modelling of flexible membrane boundaries for triaxial tests

The discrete element modelling of triaxial tests plays a critical role in unveiling fundamental properties of particulate materials, but the numerical implementation of a flexible membrane boundary for the testing still imposes problems. Here, in this work, a robust algorithm was proposed to reproduce a flexible membrane boundary in triaxial testing. The equivalence of strain energy enables the particle-scale parameters representing the flexible membrane to be directly determined from the real geometric and material parameters of the membrane. Then the proposed flexible membrane boundary was implemented in the context of discrete element simulation of triaxial testing and was validated with laboratory experiments. Furthermore, comparisons of triaxial tests with flexible and rigid boundaries were performed from macro-scale to meso-scale. Lastly, the results show that the boundary condition has limited influences on the stress-strain behaviour but a relatively large impact on the volumetric change, the failure mode, the distribution of contact forces, and the fabric evolution of particles in the specimen during triaxial testing.

42 ENGINEERING↗

Transverse impact by RCCs on S-glass and Kevlar® FRC strips

This study aims to isolate interactions between plies and tows and reveal fundamental physics involved in transverse impact on fiber-reinforced composite (FRC) structures. Composite strips were sectioned from large panels and characterized by optical photography, three-dimensional synchrotron X-ray computed tomography, and scanning electron microscopy (SEM). Each strip was impacted perpendicularly by a right circular cylinder (RCC) projectile at a velocity ranging from ~ 150 to 600 m/s. The global strip behavior, as well as localized deformation and failure of the strip near the projectile corner, were both captured by high-speed optical imaging. S-Glass FRC strips were observed to fail in tension ahead of the RCC projectiles’ flat surfaces while Kevlar® FRC strips fractured at the projectile corners. The concept of critical velocity region previously used for impact on yarns was introduced to define different failure modes of each composite strip type. The strip damage extent was found to increase with the impact velocity and reach the maximum at the upper limit of the critical velocity region. Above the critical velocity region, the damage extent decreased with impact velocity. Wave propagations and load histories in the composite strips during impact were quantified and compared with Smith’s theory. Finally, critical velocities of single fibers, yarns, and composite strips and ballistic limits of single-ply and multi-ply composite panels were compared to provide insight into the design of impact-resistant fabrics and composites.

42 ENGINEERING↗

Anisotropic thermal-conductivity degradation in the phase-field method accounting for crack directionality

Dynamic loads applied to metals may lead to brittle or ductile fracture depending on the imposed strain rates, material properties, and specimen geometry. With an increase in the applied velocity, brittle to ductile failure mode transition may also be observed. Furthermore, at high strain rates, ductile fracture may be preceded by shear bands, which are narrow bands of intense plastic deformation, typically accompanied by a significant rise in temperature. Reliable models are needed to predict the response of metals subject to dynamic loads. In particular, capturing the interplay between heat conduction and crack propagation using the phase-field fracture method is still an open research field. To accurately capture the heat transfer physics across crack surfaces, damage models degrading thermal-conductivity are necessary. While isotropic thermal-conductivity degradation models were proposed, they may lead to errors as they are indifferent to crack directionality. In our current work, a new anisotropic approach is proposed in which thermal-conductivity, which depends on the phase-field gradient, is degraded solely across the crack. Here, it is shown that this approach improves the near-field approximation of temperature and heat flux compared with isotropic degradation, when taking the discontinuous crack solutions as reference. Additionally, the anisotropic degradation approach is implemented in a unified dynamic fracture model and a couple of examples demonstrate the viability of this approach.

42 ENGINEERING↗

Scaling open-weight large language models for hydropower regulatory information extraction: A systematic analysis

Information extraction from regulatory and technical documents using large language models (LLMs) involves practical trade-offs between extraction quality and computational cost. We evaluate eight open-weight LLMs spanning 0.6B–70B parameters on hydropower licensing documents and report deployment-oriented evidence under a unified extraction schema and evaluation protocol. Across the model set, we observe clear scale-dependent trends in both baseline extraction quality and the effectiveness of reflective reasoning (self-checking) under our fixed-prompt, no-augmentation setting. Mid-scale models often provide a favorable balance of accuracy and efficiency, whereas the smallest models show limited or inconsistent gains from the reasoning variants tested. Larger models achieve the highest overall F1 scores but incur substantially greater compute and infrastructure requirements. We further find that reliability failure modes can distort conventional metrics in this domain: in particular, high recall can coincide with systematic extraction errors when models fabricate values for fields that are absent from the source text, underscoring the importance of conservative null handling and evidence-grounded evaluation. Overall, our study provides a reproducible resource–performance comparison for open-weight LLM-based extraction in hydropower regulatory documentation and offers practical guidance for model selection under different deployment constraints.

Evaluation protocol↗

Mechanical vulnerability and resistance to snapping and uprooting for Central Amazon tree species

We report high descending winds generated by convective storms are a frequent and a major source of tree mortality disturbance events in the Amazon, affecting forest structure and diversity across a variety of scales, and more frequently observed in western and central portions of the basin. Soil texture in the Central Amazon also varies significantly with elevation along a topographic gradient, with decreasing clay content on plateaus, slopes and valleys respectively. In this study we investigated the critical turning moments ( M crit - rotational force at the moment of tree failure, an indicator of tree stability or wind resistance) of 60 trees, ranging from 19.0 to 41.1 cm in diameter at breast height ( DBH ) and located in different topographic positions, and for different species, using a cable-winch load-cell system. Our approach used torque as a measure of tree failure to the point of snapping or uprooting. This approach provides a better understanding of the mechanical forces required to topple trees in tropical forests, and will inform models of wind throw disturbance. Across the topographic positions, size controlled variation in M crit was quantified for cardeiro ( Scleronema mincranthum (Ducke) Ducke), mata-matá ( Eschweilera spp.), and a random selection of trees from 19 other species. Our analysis of M crit revealed that tree resistance to failure increased with size (DBH and ABG) and differed among species. No effects of topography or failure mode were found for the species either separately or pooled. For the random species, total variance in M crit explained by tree size metrics increased from an R 2 of 0.49 for DBH alone, to 0.68 when both DBH and stem fresh wood density (SWD) were included in a multiple regression model. This mechanistic approach allows the comparison of tree vulnerability induced by wind damage across ecosystems, and facilitates the use of forest structural information in ecosystem models that include variable resistance of trees to mortality inducing factors. Furthermore, our results indicate that observed topographic differences in wind throw vulnerability are likely due to elevational differences in wind velocities, rather than by differences in soil-related factors that might effect M crit .

54 ENVIRONMENTAL SCIENCES↗

Investigating ceramic breeder pebble beds thermomechanics evolution using novel pressure mapping technology

Ceramic breeder pebble beds undergo complex thermomechanical interactions during blanket operation due to stress build-up and relaxation under the effects of confined thermal expansion, thermal cycling, and creep. Understanding the evolution of such processes can aid in guiding blanket design/assembly, breeder materials developments, predicting performance and possible failure modes. This study introduces experimental techniques that enable us to create an environment in which the pebble bed stresses are organically generated as a result of relevant temperature gradients and magnitudes that allows us to observe the combined thermomechanical interaction effects. A novel non-intrusive in-situ tactile pressure sensing technology is used to generate real-time contact pressure maps revealing the spatial and temporal stress evolution with emphasis on understanding the roles that each of the thermo-mechanical forces play in dictating the pebble bed’s equilibrium conditions. Two types of bed-wall contact pressure drop were recorded: (1) within the subsequent cycles due to pebbles irreversible rearrangements, and (2) within the cycle itself as a result of creep/stress-relaxation. Consequently, by the fourth cycle, the contact pressure drops to negligible values and remains stable. This stability is attributed to two modes of self-regulation: (1) stress self-regulation as a result of pressure rise and fall due to thermal expansion and creep/thermal cycling, respectively, and (2) temperature self-regulation due to the locally enhanced thermal conductivity in the core region of the bed accompanied by deteriorated interface conductance. These two mechanisms are desirable as they lower the probability of the events of pebbles crushing and thermal runaways under high temperatures/stresses and poor heat extraction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Calibers: A Bandwidth Calendaring Paradigm for Science Workflows

Many scientific workflows require large data transfers between distributed instrument facilities, storage and computing resources. To ensure that these resources are maximally utilized, R&E networks connecting these resources must ensure that an inherently unpredictable network behaves predictably. In practice, this amounts to the per-application over-provisioning of network resources in an attempt to guarantee that adequate throughput is provided to users. This often results in resource under-utilization over time. One promising solution is the use of deadlines and bandwidth calendaring. In this approach, "fair" resource allocation is replaced with deadline-based resource allocation. However, these approaches often suffer from issues in efficiently regulating resource allocation and failure modes. Therefore, our solution, Calibers, approaches bandwidth calendaring and deadline-awareness in a different way. Calibers uses shaping, metering, and pacing at the edge of the network and end-system to provide participating clients the ability to schedule bandwidth reservations without having to worry about network noise from non-participating clients. Calibers can also fail back to the fair resource allocation of underlying transport protocols if necessary. For example, if a non-participating flow somehow enters the core of the network, or a sudden network change causes the available bandwidth to be exceeded, the underlying transport protocol congestion avoidance implementation will be able to handle the congestion as it normally would. Furthermore, Calibers provides a novel simulation method and resource allocation algorithm.

97 MATHEMATICS AND COMPUTING↗

Data requirements for improving the Quantitative Risk Assessment of liquid hydrogen storage systems

Quantitative Risk Assessment (QRA) supports the development of risk-informed safety codes and standards which are employed to enable the safe deployment of hydrogen technologies essential to decarbonize the transportation sector. System reliability data is a necessary input for rigorous QRA. Here, the lack of reliability data for bulk liquid hydrogen (LH 2 ) storage systems located on site at fueling stations limits the use of QRAs. In turn, this hinders the ability to develop the necessary safety codes and standards that enable worldwide deployment of these stations. Through a QRA-based analysis of a LH 2 storage system, this work focuses on identifying relevant scenario and probability data currently available and ascertaining future data collection requirements regarding risks specific to liquid hydrogen releases. The work developed consists of the analysis of a general bulk LH 2 storage system design located at a hydrogen fueling station. Failure Mode and Effect Analysis (FMEA) and traditional QRA modeling tools such as Event Sequence Diagrams (ESD) and Fault Tree Analysis (FTA) are employed to identify, rank, and model risk scenarios related to the release of LH 2 . Based on this analysis, scenario and reliability data needs to add LH 2 -related components to QRA are identified with the purpose of improving the future safety and risk assessment of these systems.

08 HYDROGEN↗