Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structured Programming”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Large scale optimization using ASTROS: An overview

Interest in interdisciplinary systems is widespread around the world. A number of structural optimization systems are being developed and tested. Some examples are listed here. ASOP, FASTOP, and TSO are programs developed for the Air Force Flight Dynamics Laboratory during the seventies. These programs established the feasibility of integrating various disciplines. The program 'STARS' is basically a structural optimization system developed by the Royal Aircraft Establishment (RAE) in England. At present, it is being enhanced to include aeroelasticity. 'LAGRANGE' is an optimization system developed by MBB in Germany. ELFINI is a similar system developed in France. It is being marketed in the U.S. as well as other countries. The Automated STRuctural Optimization System (ASTROS) was developed for the Flight Dynamics Directorate of Wright Laboratory. The ASTROS system is described in viewgraph form.

Venkayya, Vipperia B.↗

Laser power beaming system analyses

The successful demonstration of the PAMELA adaptive optics hardware and the fabrication of the BTOS truss structure were identified by the program office as the two most critical elements of the NASA power beaming program, so it was these that received attention during this program. Much of the effort was expended in direct program support at MSFC, but detailed technical analyses of the AMP deterministic control scheme and the BTOS truss structure (both the JPL design and a spherical one) were prepared and are attached, and recommendations are given.

Zeiders, Glenn W., Jr.↗

Flight Dynamics Laboratory overview

The Flight Dynamics Laboratory (FDL) is one of four Air Force Wright Aeronautical Laboratories (AFWAL) and part of the Aeronautical Systems Division located at Wright-Patterson AFB, Ohio. The FDL is responsible for the planning and execution of research and development programs in the areas of structures and dynamics, flight controls, vehicle equipment/subsystems, and aeromechanics. Some of the areas being researched in the four FDL divisions are as follows: large space structures (LSS) materials and controls; advanced cockpit designs; bird-strike-tolerant windshields; and hypersonic interceptor system studies. Two of the FDL divisions are actively involved in programs that deal directly with LSS control/structures interaction: the Flight Controls Division and the Structures and Dynamics Division.

Sandford, Thaddeus↗

A Scheme for finding the Front Boundary of an Interplanetary Magnetic Cloud

We developed a scheme for finding the front boundary of an interplanetary magnetic cloud (MC) based on criteria that depend on the possible existence of any one or all of six specific solar wind features. The features that the program looks for, within +/- 2 hours of a preliminarily determined time for the front boundary, estimated either by visual inspection or by an automatic MC identification scheme, are: (1) a sufficiently large directional discontinuity in the interplanetary magnetic field (IMF), (2) existence of a magnetic hole, (3) a significant proton plasma beta drop, (4) a significant proton temperature drop, (5) a marked increase in the IMF's intensity, and (6) a significant decrease in a normalized root-mean-square deviation (RMS)of the magnetic field - where the scheme was tested using 5, 10, 15, and 20 minute averages of the relevant physical quantities, in order to find the optimum average (and RMS) to use. Other criteria, besides these six, were examined and dismissed as not reliable, e.g., plasma speed. The scheme was developed specifically for aiding in forecasting the strength and timing of a geomagnetic storm due to the passage of an interplanetary MC in real-time, but can be used in post ground-data collection for imposition of consistency in choosing a MC's front boundary. The scheme has been extensively tested, first using 80 bona fide MCs over about 9 years of WIND data, and also for 121 MC-like structures as defined by a program that automatically identifies such structures over the same period. Optimum limits for various parameters in the scheme were found by statistical studies of the WIND MCs. The resulting limits can be user-adjusted for other data sets, if desired. Final testing of the 80 MCs showed that for 50 percent of the events the boundary estimates occurred within +/-10 minutes of visually determined times, 80 percent occurred within +/-30 minutes, and 91 percent occur within +/-60 minutes, and three or more individual boundary tests were passed for 88 percent of the total MCs. The scheme and its testing will be described.

Lepping, Ronald P.↗

Probabilistic Structural Analysis Theory Development

The objective of the Probabilistic Structural Analysis Methods (PSAM) project is to develop analysis techniques and computer programs for predicting the probabilistic response of critical structural components for current and future space propulsion systems. This technology will play a central role in establishing system performance and durability. The first year's technical activity is concentrating on probabilistic finite element formulation strategy and code development. Work is also in progress to survey critical materials and space shuttle mian engine components. The probabilistic finite element computer program NESSUS (Numerical Evaluation of Stochastic Structures Under Stress) is being developed. The final probabilistic code will have, in the general case, the capability of performing nonlinear dynamic of stochastic structures. It is the goal of the approximate methods effort to increase problem solving efficiency relative to finite element methods by using energy methods to generate trial solutions which satisfy the structural boundary conditions. These approximate methods will be less computer intensive relative to the finite element approach.

Burnside, O. H.↗

Preliminary design procedure for insulated structures subjected to transient heating

Minimum-mass designs were obtained for insulated structural panels loaded by a general set of inplane forces and a time dependent temperature. Temperature and stress histories in the structure are given by closed-form solutions, and optimization of the insulation and structural thicknesses is performed by nonlinear mathematical programming techniques. Design calculations are described to evaluate the structural efficiency of eight materials under combined heating and mechanical loads: graphite/polyimide, graphite/epoxy, boron/aluminum, titanium, aluminum, Rene 41, carbon/carbon, and Lockalloy. The effect on design mass of intensity and duration of heating were assessed. Results indicate that an optimum structure may have a temperature response well below the recommended allowable temperature for the material.

Adelman, H. M.↗

Analysis and sizing of Mars aerobrake structure

A cone-sphere aeroshell structure for aerobraking into Martian atmosphere is studied. Using this structural configuration, a space frame load-bearing structure is proposed. To generate this structure efficiently and to perform a variety of studies of several configurations, a mesh generator that utilizes only a few configurational parameters is developed. A finite element analysis program that analyzes space frame structures was developed. A sizing algorithm that arrives at a minimum mass configuration was developed and integrated into the finite element analysis program. A typical 135-ft-diam aerobrake configuration was analyzed and sized. The minimum mass obtained in this study using high modulus graphite/epoxy composite material members is compared with the masses obtained from two other aerobrake structures using lightweight erectable tetrahedral truss and part-spherical truss configurations. Excellent agreement for the minimum mass was obtained with the three different aerobrake structures. Also, the minimum mass using the present structure was obtained when the supports were not at the base but at about 75 percent of the base diameter.

Raju, I. S.↗

Characterization of Al-Cu-Mg-Ag Alloy RX226-T8 Plate

Aluminum-copper-magnesium-silver (Al-Cu-Mg-Ag) alloys that were developed for thermal stability also offer attractive ambient temperature strength-toughness combinations, and therefore, can be considered for a broad range of airframe structural applications. The current study evaluated Al-Cu-Mg-Ag alloy RX226-T8 in plate gages and compared performance with sheet gage alloys of similar composition. Uniaxial tensile properties, plane strain initiation fracture toughness, and plane stress tearing resistance of RX226-T8 were examined at ambient temperature as a function of orientation and thickness location in the plate. Properties were measured near the surface and at the mid-plane of the plate. Tensile strengths were essentially isotropic, with variations in yield and ultimate tensile strengths of less than 2% as a function of orientation and through-thickness location. However, ductility varied by more than 15% with orientation. Fracture toughness was generally higher at the mid-plane and greater for the L-T orientation, although the differences were small near the surface of the plate. Metallurgical analysis indicated that the microstructure was primarily recrystallized with weak texture and was uniform through the plate with the exception of a fine-grained layer near the surface of the plate. Scanning electron microscope analysis revealed Al-Cu-Mg second phase particles which varied in composition and were primarily located on grain boundaries parallel to the rolling direction. Fractography of toughness specimens for both plate locations and orientations revealed that fracture occurred predominantly by transgranular microvoid coalescence. Introduction High-strength, low-density Al-Cu-Mg-Ag alloys were initially developed to replace conventional 2000 (Al-Cu-Mg) and 7000 (Al-Zn-Cu-Mg) series aluminum alloys for aircraft structural applications [1]. During the High Speed Civil Transport (HSCT) program, improvements in thermal stability were demonstrated for candidate aircraft wing and fuselage skin materials through the addition of silver to Al-Cu-Mg alloys based on Al 2519 chemistry [2]. Thermal stability of the resulting Al-Cu-Mg-Ag alloys, C415-T8 and C416-T8, was due to co-precipitation of the thermally stable . (AlCu) and ' (Al2Cu) strengthening phases [1-4]. The strength and toughness behavior was investigated for these alloys produced as 0.090-inch thick rolled sheet in the T8 condition and after various thermal exposures. The mechanical properties were shown to be competitive with conventional aircraft alloys, 2519-T8 and 2618-T8 [2]. During the Integral Airframe Structure (IAS) program, advanced aluminum alloys were examined for use in an integrally stiffened airframe structure where the skin and stiffeners would be machined from plate and extruded frames would be mechanically attached (see Figure 1) [5]. Advantages of integrally stiffened structure include reduced part count, and reduced assembly times compared to conventional built-up airframe structure. The near-surface properties of a thick plate are of significance for a machined integrally stiffened airframe structure since this represents the skin location. Properties measured at the mid-plane of the plate are more representative of the stiffener web. RX226 was developed to exploit strength-toughness improvements and thermal stability benefits of Al-Cu-Mg-Ag alloys in plate gages. This study evaluated the microstructure and properties of three gages of plate produced in the T8 condition.

Lach, Cynthia L.↗

Ground test of large flexible structures

Many future mission models require large space (LSS) which have accurate surfaces and/or the capability of being accurately aligned. If ground test approaches which will provide adequate confidence of the structrual performance to the program managers are not developed, many viable structural concepts may never be utilized. The size and flexibility of many of the structural concepts will preclude the use of the current ground test methods because of the adverse effects of the terrestrial environment. The challenge is to develop new test approaches which will provide confidence in the capability of LSS to meet performance requirements prior to flight. The activities on ground testing of LSS are described. Since some of the proposed structural systems cannot be tested in entirety, a coordinated ground test analytical model program is required to predict structural performance in space. Several concepts of ground testing under development are addressed.

Wada, Ben K.↗

The evolution of the FIGARO data reduction system

The Figaro data reduction system originated at Caltech around 1983. It was based on concepts being developed in the U.K. by the Starlink organization, particularly the use of hierarchical self-defining data structures and the abstraction of most user-interaction into a set of 'parameter system' routines. Since 1984 it has continued to be developed at AAO, in collaboration with Starlink and Caltech. It was adopted as Starlink's main spectroscopic data reduction package, although it is by no means limited to spectra; it has operations for images and data cubes and even a few (very specialized) for four-dimensional data hypercubes. It continued to be used at Caltech and will be used at the Keck. It is also in use at a variety of other organizations around the world. Figaro was originally a system for VMS Vaxes. Recently it was ported (at Caltech) to run on SUN's, and work is underway at the University of New South Wales on a DecStation version. It is hoped to coordinate all this work into a unified release, but coordination of the development of a system by organizations covering three continents poses a number of interesting administrative problems. The hierarchical data structures used by Figaro allow it to handle a variety of types of data, and to add new items to data structures. Error and data quality information was added to the basic file format used, error information being particularly useful for infrared data. Cooperating sets of programs can add specific sub-structures to data files to carry information that they understand (polarimetry data containing multiple data arrays, for example), without this affecting the way other programs handle the files. Complex instrument-specific ancillary information can be added to data files written at a telescope and can be used by programs that understand the instrumental details in order to produce properly calibrated data files. Once this preliminary data processing was done the resulting files contain 'ordinary' spectra or images that can be processed by programs that are not instrument-specific. The structures holding the instrumental information can then be discarded from the files. Much effort has gone into trying to make it easy to write Figaro programs; data access subroutines are now available to handle access to all the conventional items found in Figaro files (main data arrays, error information, quality information etc), and programs that only need to access such items can be very simple indeed. A large number of Figaro users do indeed write their own Figaro applications using these routines. The fact that Figaro programs are written as callable subroutines getting information from the user through a small set of parameter routines means that they can be invoked in numerous ways; they are normally linked and run as individual programs (called by a small main routine that is generated automatically), but are also available linked to run under the ADAM data acquisition system and there is an interface that lets them be called as part of a user-written Fortran program. The long-term future of Figaro probably depends to a large extent on how successfully it manages the transition from being a VMS-only system to being a multi-platform system.

Shortridge, K.↗

BGRID: A block-structured grid generation code for wing sections

The operation of the BGRID computer program is described for generating block-structured grids. Examples are provided to illustrate the code input and output. The application of a fully implicit AF (approximation factorization)-based computer code, called TWINGB (Transonic WING), for solving the 3D transonic full potential equation in conservation form on block-structured grids is also discussed.

Chen, H. C.↗

Program design by a multidisciplinary team

The use of software engineering aids in the design of a structural finite-element analysis computer program for the STAR-100 computer is described. Nested functional diagrams to aid in communication among design team members were used, and a standardized specification format to describe modules designed by various members was adopted. This is a report of current work in which use of the functional diagrams provided continuity and helped resolve some of the problems arising in this long-running part-time project.

Voigt, S.↗

Roll diffusion bonding of titanium alloy panels

Roll diffusion bonding technique is used for fabricating T-stiffened panel assemblies from titanium alloy. The single unit fabrication exhibits excellent strength characteristics under tensile and compressive loads. This program is applied to structures in which weight/strength ratio and integral construction are important considerations.

Bennett, J.↗