Search NASA⌕ Search

SEARCH · Search NASA

Results for “buffer layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Phosphorus transformation response to soil properties changes induced by manure application in a calcareous soil

Management of phosphorus (P) loss in soils with heavy manure application requires improved understanding of the transformation characteristics of soil P. Influences of manure application on the forms and sorption-desorption characteristics of P in surface (0–30 cm) and subsurface (30–60 cm) layer of a calcareous soil were investigated in this paper in a six-year field trial in comparison to chemical fertilizer application. Hedley fractionation and P K-edge X-ray absorption near-edge structure spectroscopy were used to determine the soil P forms. Manure (M) and chemical fertilizer (F) treatments resulted in P accumulation in two soil depths, but the total P accumulation in surface soil with M treatment was significantly lower than F treatment with similar P surplus. Compared to control, M and F treatments were significantly increased the proportion of labile P at both depths. In surface soil, M treatment significantly decreased stable Ca-associated P proportion and increased Fe-associated P and inositol hexakisphosphate proportions. The accumulation and transformation of P in M treatment distinctly decreased P sorption maximun, sorption coefficient and buffer capacity, and increased the degree of P saturation and P desorption relative to F treatment. The soil properties of pH, organic carbon (OC), total nitrogen (TN), Mehlich-3 extractable Ca and Fe, and phytase in surface soil and pH, OC, TN, Mehlich-3 extractable Ca and dehydrogenase in subsurface soil had significant effects on the compositions of soil P (P < 0.05), respectively. Finally, lowered pH due to manure application mainly contributed to P transformation and release in the calcareous soil.

54 ENVIRONMENTAL SCIENCES↗

Synthesis of Hexagonal Boron Nitride Mono layer: Control of Nucleation and Crystal Morphology

Mono layer hexagonal boron nitride (hBN) attracts significant attention due to the potential to be used as a complementary two-dimensional dielectric in fabrication of functional 2D heterostructures. Here we investigate the growth stages of the hBN single crystals and show that hBN crystals change their shape from triangular to truncated triangular and further to hexagonal depending on copper substrate distance from the precursor. We suggest that the observed hBN crystal shape variation is affected by the ratio of boron to nitrogen active species concentrations on the copper surface inside the CVD reactor. Strong temperature dependence reveals the activation energies for the hBN nucleation process of similar to 5 eV and crystal growth of similar to 3.5 eV. We also show that the resulting h-BN film morphology is strongly affected by the heating method of borazane precursor and the buffer gas. Elucidation of these details facilitated synthesis of high quality large area monolayer hexagonal boron nitride by atmospheric pressure chemical vapor deposition on copper using borazane as a precursor.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Embedding ceramic components in metal structures with hybrid directed energy deposition

The combined benefit of both additive and subtractive manufacturing within the same gantry system enables hybrid directed energy deposition to create complex geometries with smooth surface finish and superior dimensional accuracy. Moreover, with layer-by-layer access to the structure during both the addition and subtraction of material, the insertion of components is now possible, assuming the components can survive the high temperatures associated with the subsequent metal deposition. Ceramic inserts are of interest for a variety of reasons including (1) to create complex interwoven ductile/brittle composites for ballistics or high-temperature applications or (2) to integrate high-temperature strain or temperature sensors protected within ceramic substrate subsumed into a larger metal structure. Here, in this work, stainless steel substrates were machined to create an internal cavity for the insertion of a ceramic component. During the investigation of several different over-the-ceramic deposition strategies, components were inserted, and different process sequences were allowed to continue to envelop the inserted ceramic with varying success. Unmelted powder was used to serve both as a thermal buffer and to provide a flush surface upon which the laser cladding could continue. Subsequent depositions were attempted with both dry and wet powder (addition of machining coolant to wet). The wet powder has previously been demonstrated to not significantly impact the mechanical properties of a final structure and provided a thermal barrier to protect the ceramic piece from the extreme temperatures of the final metal deposition. The wetting of the powder provided stability and minimized displacement caused by the powder flow from the laser cladding head. Finally, the use of an oblique angle for laser cladding allowed for the redirection of some fraction of the introduced thermal energy away from the ceramic component and, consequently, improved the survival of the ceramic inserts. With this combination of techniques, ceramic inserts survived full embedding within a 3D-printed stainless steel structure.

36 MATERIALS SCIENCE↗

Performance of the THS4302 and the Class V Radiation-Tolerant THS4304-SP Silicon Germanium Wideband Amplifiers at Extreme Temperatures

This report discusses the performance of silicon germanium, wideband gain amplifiers under extreme temperatures. The investigated devices include Texas Instruments THS4304-SP and THS4302 amplifiers. Both chips are manufactured using the BiCom3 process based on silicon germanium technology along with silicon-on-insulator (SOI) buried oxide layers. The THS4304-SP device was chosen because it is a Class V radiation-tolerant (150 kRad, TID silicon), voltage-feedback operational amplifier designed for use in high-speed analog signal applications and is very desirable for NASA missions. It operates with a single 5 V power supply [1]. It comes in a 10-pin ceramic flatpack package, and it provides balanced inputs, low offset voltage and offset current, and high common mode rejection ratio. The fixed-gain THS4302 chip, which comes in a 16-pin leadless package, offers high bandwidth, high slew rate, low noise, and low distortion [2]. Such features have made the amplifier useful in a number of applications such as wideband signal processing, wireless transceivers, intermediate frequency (IF) amplifier, analog-to-digital converter (ADC) preamplifier, digital-to-analog converter (DAC) output buffer, measurement instrumentation, and medical and industrial imaging.

Patterson, Richard L.↗

Microphysical, Macrophysical and Radiative Signatures of Volcanic Aerosols in Trade Wind Cumulus Observed by the A-Train

Increased aerosol concentrations can raise planetary albedo not only by reflecting sunlight and increasing cloud albedo, but also by changing cloud amount. However, detecting aerosol effect on cloud amount has been elusive to both observations and modeling due to potential buffering mechanisms and convolution of meteorology. Here through a natural experiment provided by long-tem1 degassing of a low-lying volcano and use of A-Train satellite observations, we show modifications of trade cumulus cloud fields including decreased droplet size, decreased precipitation efficiency and increased cloud amount are associated with volcanic aerosols. In addition we find significantly higher cloud tops for polluted clouds. We demonstrate that the observed microphysical and macrophysical changes cannot be explained by synoptic meteorology or the orographic effect of the Hawaiian Islands. The "total shortwave aerosol forcin", resulting from direct and indirect forcings including both cloud albedo and cloud amount. is almost an order of magnitude higher than aerosol direct forcing alone. Furthermore, the precipitation reduction associated with enhanced aerosol leads to large changes in the energetics of air-sea exchange and trade wind boundary layer. Our results represent the first observational evidence of large-scale increase of cloud amount due to aerosols in a trade cumulus regime, which can be used to constrain the representation of aerosol-cloud interactions in climate models. The findings also have implications for volcano-climate interactions and climate mitigation research.

Yuan, T.↗

Carbon Solubility in Silicon-Iron-Bearing Metals during Core Formation on Mercury

Recent results obtained from the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) spacecraft showed the surface of Mercury has high S abundances (approximately 4 wt%) and low Iron(II) Oxide abundances (less than 2 wt%). Based on these extreme values, the oxygen fugacity of Mercury's surface materials was estimated to be approximately 3 to 7 log(sub 10) units below the IW buffer (Delta IW-3 to Delta IW-7). This highly reducing nature of the planet has resulted in a large core and relatively thin mantle, extending to only approximately 420 km depth (corresponding to a core-mantle boundary pressure of approximately 4-7 GPa) within the planet. Furthermore, MESSENGER results have suggested the presence of carbon on the surface of the planet. Previous experimental results from have also suggested the possibility of a primary floatation crust on Mercury composed of graphite, produced after a global magma ocean event. With these exotic conditions of this compositional end-member planet, it begs the question, what is the core composition of Mercury? Although no definitive conclusion has been reached, previous studies have made advances towards answering this question. Riner et al. and Chen et al. looked at iron sulfide systems and implemented various crystallization and layered core scenarios to try and determine the composition and structure of Mercury's core. Malavergne et al. examined core crystallization scenarios in the presence of sulfur and silicon. Hauck et al. used the most recent geophysical constraints from the MESSENGER spacecraft to model the internal structure of Mercury, including the core, in a iron-sulfur-silicon system. More recently, Chabot et al. conducted a series of metal-silicate partitioning experiments in a iron-sulfur-silicon system. These results showed the core of Mercury has the potential to contain more than 15 wt% silicon. However, with the newest results from MESSENGER's low altitude campaign, carbon is another potential light element that could be incorporated into Mercury's core. The goal of this study is to determine the carbon concentration at graphite saturation in various silicon-iron bearing metals relevant to possible mercurian core compositions. Future experiments will include the addition of sulfur into these metals.

Vander Kaaden, Kathleen E.↗

Guided Optimization of Phase-Unstable III–V Compositionally Graded Buffers by Cathodoluminescence Spectrum Imaging

Compositionally graded buffers (CGBs) are essential components of high-efficiency III-V inverted metamorphic solar cells, and high-quality CGBs with low defect densities are a requirement for high device efficiencies. Here, we use plan-view and cross-sectional cathodoluminescence spectrum imaging (CLSI) to investigate the effect of growth conditions on the microstructure of Al y Ga 1-x-y In x AS CGBs with x In > 0.30. CLSI reveals significant compositional fluctuation in these materials that correlates with the distribution of threading dislocations in the CGBs. Threading dislocations are observed to collect in regions between abrupt transitions in emission energy, implying that concomitant strain fluctuations in these regions restrict dislocation motion. Thus, the compositional fluctuation leads to elevated threading dislocation densities that degrade CGB quality. We also correlate compositional fluctuation in the CGB with compositional fluctuation in subsequently grown device layers. The effectiveness of specific growth conditions at suppressing compositional fluctuation and limiting threading dislocation density is evaluated. CGBs grown at high temperatures with high Al content exhibit the lowest defect densities. The use of a high V/III ratio suppresses compositional fluctuation and defect density. In conclusion, these insights lead directly to improvements in the efficiency of metamorphic Ga 1-x In x As solar cells grown on AlyGa 1-x-y In x As CGBs.

14 SOLAR ENERGY↗

Model of temperature, evaporation, and productivity in elevated experimental algae raceways and comparison with commercial raceways

Elevated Experimental Raceways (EERs) have been used at many research sites in the United States to evaluate algal biomass productivity. This paper develops temperature and evaporation models for EERs and then evaluates whether the temperature profile and resultant productivity in an EER is representative of large-scale commercial raceways. Open water surface evaporation and temperature models with shading algorithms were programmed in Python and calibrated with temperature and evaporation data from the EERs in the Regional Algal Feedstock Testbed (RAFT) experiments at the University of Arizona. The final calibrated model for EERs was named the EERTEM (Elevated Experimental Raceway Temperature and Evaporation Model). The energy balance algorithms in the Biomass Assessment Tool (BAT model) were also added to the Python code and used to develop temperature simulations of standard commercial paddlewheel raceways. A comparison of BAT and EERTEM simulations indicated that EER temperature fluctuations are not representative of in ground commercial paddlewheel raceways, primarily due to the buffering effect of soil heat flux in commercial raceways. With the different temperature profiles, biomass productivities of three algae species in the EERs were compared to productivities in commercial raceways. Differences in productivity between EERTEM and BAT model temperature profiles were observed when the maximum daytime temperature of one raceway was in the optimal growth range but the temperature of the other raceway exceeded or was below the optimal growth range.

Khawam, George↗

Growth mechanism of ZnO low-temperature homoepitaxy

The authors report on the growth mechanism of ZnO homoepitaxy at the low-temperature range of 500 deg. C, which is unavailable to obtain high-quality ZnO films in heteroepitaxy. One typical set of ZnO films were grown on (0001) ZnO substrates by molecular-beam epitaxy: a standard structure without buffer and two buffered structures with high-temperature (HT) homobuffer and low-temperature (LT) homobuffer. As a result, the LT homobuffered structure had the outstanding material properties: the surface roughness is 0.9 nm, the full width at half maximum of x-ray rocking curve is 13 arcsec, and the emission linewidth of donor-bound excitons is 2.4 meV. In terms of the theoretical interpretation of the experimentally obtained electron mobilities, it was found that the LT homobuffered structure suffers less from the dislocation scattering and the ionized-impurity scattering compared to the HT homobuffered structure. It is proposed that, in the ZnO low-temperature homoepitaxy, the LT homobuffer plays a key role in inducing the complete termination of dislocations in the homointerface and suppressing the outdiffusion of contaminants and point defects on the ZnO surface, which results in the formation of smooth wetting layer on the homointerface.

36 MATERIALS SCIENCE↗

Visible photoelectrochemical water splitting into H 2 and O 2 in a dye-sensitized photoelectrosynthesis cell

A hybrid strategy for solar water splitting is exploited here based on a dye-sensitized photoelectrosynthesis cell (DSPEC) with a mesoporous SnO 2 /TiO 2 core/shell nanostructured electrode derivatized with a surface-bound Ru(II) polypyridyl-based chromophore–catalyst assembly. The assembly, [(4,4’-(PO 3 H 2 ) 2 bpy) 2 Ru(4-Mebpy-4’-bimpy)Ru(tpy)(OH 2 )] 4+ ([RuaII-RubII-OH 2 ] 4+ , combines both a light absorber and a water oxidation catalyst in a single molecule. It was attached to the TiO 2 shell by phosphonate-surface oxide binding. The oxide-bound assembly was further stabilized on the surface by atomic layer deposition (ALD) of either Al 2 O 3 or TiO 2 overlayers. Illumination of the resulting fluorine-doped tin oxide (FTO)|SnO 2 /TiO 2 |-[Ru a II -Ru b II -OH 2 ] 4+ (Al 2 O 3 or TiO 2 ) photoanodes in photoelectrochemical cells with a Pt cathode and a small applied bias resulted in visible-light water splitting as shown by direct measurements of both evolved H 2 and O 2 . The performance of the resulting DSPECs varies with shell thickness and the nature and extent of the oxide overlayer. Use of the SnO 2 /TiO 2 core/shell compared with nanoITO/TiO 2 with the same assembly results in photocurrent enhancements of ~5. In conclusion, systematic variations in shell thickness and ALD overlayer lead to photocurrent densities as high as 1.97 mA/cm 2 with 445-nm, ~90-mW/cm 2 illumination in a phosphate buffer at pH 7.

36 MATERIALS SCIENCE↗

Final Closure of the Maxey Flats Low-Level Radioactive Waste Disposal Site - 16088

This paper describes the final closure remedy for the former Maxey Flats Low-Level Radioactive Waste Disposal Site (MFDS), the challenges presented at the site due to the condition of the disposal facility and waste, and their resolution through comprehensive geo-synthetic design. The MFDS is an inactive landfill located in Kentucky on a ridge surrounded by a buffer zone. Historically, waste disposal occurred without reducing voids or without compacting the placed waste. Settlement and water management issues led to releases of radioactive contamination into surrounding waters, resulting in the closure of the facility in 1977. The final closure remedy consists of 1) development and implementation oversight of a sump abandonment design to ensure no direct pathways for infiltrating water to contact the waste and 2) development and implementation oversight of the Final Closure Period (FCP) cap design. Challenges successfully addressed by the FCP scope included: Abandon sumps to minimize storm water migrating into the waste; Address potential existing groundwater waste interaction; Maximum use of on-site cap construction materials; Design cap to fit very restricted site footprint; Assess and address potential isolated differential settlement; Maximize passive storm water management; Provide alternative site access during construction. The FCP remedy and resultant design satisfies these challenges through use of layers of geo-grid-reinforced soil and geo-synthetic materials, contours and slopes that minimize the quantities of construction materials while maximizing the use of available material, probabilistic subsidence modeling, an integrated storm water management system ensuring the slow release of storm water into receiving streams, and a dedicated construction haul road system. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

High-efficiency single-junction p-i-n GaAs solar cell on roll-to-roll epi-ready flexible metal foils for low-cost photovoltaics

We demonstrate the fabrication and characterization of high-efficiency, single-junction p-i-n GaAs solar cells, on flexible metal foil with epi-ready buffer via roll-to-roll fabrication. Single-junction p-i-n GaAs solar cells were fabricated using metal–organic chemical vapor deposition (MOCVD). Furthermore, an efficiency greater than 13% was obtained at 1 sun, which is the highest reported efficiency on GaAs photovoltaics directly deposited on metal tapes. This exceeds our previously reported study showcasing 11.5% efficiency on single-junction p-n solar cell structure. Improved morphology of p-i-n structure compared with p-n is explained by atomic force microscopy (AFM), scanning electron microscopy (SEM), and helium ion microscopy (HIM) measurements. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) analysis showed reduced Zn diffusion in p-i-n cell compared with the p-n cell. We attribute the improvement in efficiency of p-i-n cells on flexible metal tapes to the quality of the junction, surface morphology, controlled diffusion of species within the active layers, and increase in absorption due to the optimized intrinsic layer thickness.

14 SOLAR ENERGY↗

Fission product distribution in irradiated safety-tested and as-irradiated AGR-2 TRISO particles

In this work, two tristructural isotropic (TRISO)-coated nuclear fuel particles were examined by electron probe microanalysis (EPMA) as part of the Advanced Gas Reactor program. The compacts’ average irradiation temperatures ranged from approximately 1260 to 1290 °C. One particle was examined in the as-irradiated condition, while the other was subject to 1600 °C post-irradiation safety testing. This study was undertaken to test a newly-developed EPMA technique to determine fission product masses in TRISO particles on a layer-by-layer basis, and to compare fission product distributions between an as-irradiated and safety-tested particle. Fission product concentration profiles were collected along two radii in each particle, with measured concentrations used to compute the fission product mass in each TRISO particle layer. These measured masses were then compared to those predicted from ORIGEN modeling calculations. Data collected from these measurements show that for these two particles, masses determined via EPMA were within ± 20% of the calculated masses for the rare-earth elements, Mo, Zr, Cs, I, and Pd. Elements that tend to be less homogeneously distributed include Sr, Te, Eu, Ag, and possibly Ba. Measured Ag masses differed by more than 40% from the calculated mass. Lanthanides other than Eu remain primarily within the fuel kernel in the as-irradiated particle but in the safety-tested particle these element masses were divided approximately equally between the kernel and kernel periphery. In both particles, the majority of Sr and Eu accumulated in the carbon-rich kernel periphery, although in the safety-tested particle, Sr and Eu accumulated farther from the fuel kernel than occurred with irradiation alone. A greater mass fraction of mobile elements, such as Cs and I accumulated in the buffer and IPyC in the safety-tested particle as compared to the as-irradiated particle. When fully developed and tested, this mass balance approach to TRISO particle analysis has the potential to provide insight into fuel behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

TCDD induces dermal accumulation of keratinocyte-derived matrix metalloproteinase-10 in an organotypic model of human skin

The epidermis of skin is the first line of defense against the environment. A three dimensional model of human skin was used to investigate tissue-specific phenotypes induced by the environmental contaminant, 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD). Continuous treatment of organotypic cultures of human keratinocytes with TCDD resulted in intracellular spaces between keratinocytes of the basal and immediately suprabasal layers as well as thinning of the basement membrane, in addition to the previously reported hyperkeratinization. These tissue remodeling events were preceded temporally by changes in expression of the extracellular matrix degrading enzyme, matrix metalloproteinase-10 (MMP-10). In organotypic cultures MMP-10 mRNA and protein were highly induced following TCDD treatment. Q-PCR and immunoblot results from TCDD-treated monolayer cultures, as well as indirect immunofluorescence and immunoblot analysis of TCDD-treated organotypic cultures, showed that MMP-10 was specifically contributed by the epidermal keratinocytes but not the dermal fibroblasts. Keratinocyte-derived MMP-10 protein accumulated over time in the dermal compartment of organotypic cultures. TCDD-induced epidermal phenotypes in organotypic cultures were attenuated by the keratinocyte-specific expression of tissue inhibitor of metalloproteinase-1, a known inhibitor of MMP-10. These studies suggest that MMP-10 and possibly other MMP-10-activated MMPs are responsible for the phenotypes exhibited in the basement membrane, the basal keratinocyte layer, and the cornified layer of TCDD-treated organotypic cultures. Our studies reveal a novel mechanism by which the epithelial–stromal microenvironment is altered in a tissue-specific manner thereby inducing structural and functional pathology in the interfollicular epidermis of human skin. - Highlights: • TCDD causes hyperkeratosis and basement membrane changes in a model of human skin. • TCDD induces MMP-10 expression in organotypic cultures of human keratinocytes. • Keratinocyte-expressed MMP-10 accumulates in the dermal compartment. • Keratinocyte K14 promoter-driven TIMP-1 expression ablates TCDD-induced phenotypes.

60 APPLIED LIFE SCIENCES↗

Persistent Expression Changes of Fibrosis-Related Genes in the Lung Tissues of Rats Exposed to Lunar Dust Particles

The Moon's surface is covered by a layer of fine, potential reactive dust. Lunar dust contain about 1‐2% of very fine respirable dust (less than 3 micrometers). The habitable area of any lunar landing vehicle and outpost would inevitably be contaminated with lunar dust that could pose a health risk. The purpose of the study is to evaluate the toxicity of Apollo moon dust in rodents to assess the health risk of dust exposures to humans. One of the particular interests in the study is to evaluate dust‐induced changes of the expression of fibrosis‐related genes, and to identify specific signaling pathways involved in lunar dustinduced toxicity. F344 rats were exposed for 4 weeks (6h/d; 5d/wk) in nose‐only inhalation chambers to concentrations of 0 (control air), 2.1, 6.8, 21, and 61 milligrams per cubic meters of lunar dust. Five rats per group were euthanized at 1 day, 1 week, 1 month, and 3 months after the last inhalation exposure. The bronchoalveolar lavage fluid (BALF) was collected by lavaging with phosphate‐buffered saline (PBS). A zymosan‐induced luminolbased chemiluminescence assay was used to assess the activity of BAL cells. The lavaged lung tissue was snap frozen in LN2 and total RNA was isolated using the Qigen RNeasy kit. The expression of 84 fibrosisrelated genes were analyzed using the RT2 Profiler PCR Array technique. The expression of 18 genes of interest were further measured using real‐time PCR technique in all the samples. 10 out of 18 genes of interest showed persistently significant expression changes in the local lung tissue exposed to lunar dust, indicating a prolonged proinflammatory response. The expressions of several of these genes were dose‐ and time‐dependent and were significantly correlated with other pathological parameters. The potential signaling pathways and upstream regulators were further analyzed using IPA pathway analysis tool based on the gene expression data. The data presented in this study, for the first time, explore the molecular mechanisms of lunar dust induced toxicity, contributing not only the risk assessment for future space exploration, but also understandings of the dust‐induced toxicity in humans on earth.

Zhang, Ye↗

Determination of lattice parameters, strain state and composition in semipolar III-nitrides using high resolution X-ray diffraction

In group-III-nitride heterostructures with semipolar or nonpolar crystal orientation, anisotropic lattice and thermal mismatch with the buffer or substrate lead to a complex distortion of the unit cells, e.g., by shearing of the lattice. This makes an accurate determination of lattice parameters, composition, and strain state under assumption of the hexagonal symmetry impossible. In this work, we present a procedure to accurately determine the lattice constants, strain state, and composition of semipolar heterostructures using high resolution X-ray diffraction. An analysis of the unit cell distortion shows that four independent lattice parameters are sufficient to describe this distortion. Assuming only small deviations from an ideal hexagonal structure, a linear expression for the interplanar distances d{sub hkl} is derived. It is used to determine the lattice parameters from high resolution X-ray diffraction 2ϑ-ω-scans of multiple on- and off-axis reflections via a weighted least-square fit. The strain and composition of ternary alloys are then evaluated by transforming the elastic parameters (using Hooke's law) from the natural crystal-fixed coordinate system to a layer-based system, given by the in-plane directions and the growth direction. We illustrate our procedure taking an example of (112{sup ¯}2) Al{sub κ}Ga{sub 1−κ}N epilayers with Al-contents over the entire composition range. We separately identify the in-plane and out-of-plane strains and discuss origins for the observed anisotropy.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Hydroforming of elliptical cavities

Activities of the past several years in developing the technique of forming seamless (weldless) cavity cells by hydroforming are summarized. An overview of the technique developed at DESY for the fabrication of single cells and multicells of the TESLA cavity shape is given and the major rf results are presented. The forming is performed by expanding a seamless tube with internal water pressure while simultaneously swaging it axially. Prior to the expansion the tube is necked at the iris area and at the ends. Tube radii and axial displacements are computer controlled during the forming process in accordance with results of finite element method simulations for necking and expansion using the experimentally obtained strain-stress relationship of tube material. In cooperation with industry different methods of niobium seamless tube production have been explored. The most appropriate and successful method is a combination of spinning or deep drawing with flow forming. Several single-cell niobium cavities of the 1.3 GHz TESLA shape were produced by hydroforming. They reached accelerating gradients E acc up to 35 MV/m after buffered chemical polishing (BCP) and up to 42 MV/m after electropolishing (EP). More recent work concentrated on fabrication and testing of multicell and nine-cell cavities. Several seamless two- and three-cell units were explored. Accelerating gradients E acc of 30–35 MV/m were measured after BCP and E acc up to 40 MV/m were reached after EP. Nine-cell niobium cavities combining three three-cell units were completed at the company E. Zanon. These cavities reached accelerating gradients of E acc = 30–35 MV/m. One cavity is successfully integrated in an XFEL cryomodule and is used in the operation of the FLASH linear accelerator at DESY. Additionally the fabrication of bimetallic single-cell and multicell NbCu cavities by hydroforming was successfully developed. Several NbCu clad single-cell and double-cell cavities of the TESLA shape have been fabricated. The clad seamless tubes were produced using hot bonding or explosive bonding and subsequent flow forming. The thicknesses of Nb and Cu layers in the tube wall are about 1 and 3 mm respectively. The rf performance of the best NbCu clad cavities is similar to that of bulk Nb cavities. The highest accelerating gradient achieved was 40 MV/m. The advantages and disadvantages of hydroformed cavities are discussed in this paper.

36 MATERIALS SCIENCE↗

Redeposition in plasma-assisted atomic layer deposition: Silicon nitride film quality ruled by the gas residence time

The requirements on the material properties and growth control of silicon nitride (SiN{sub x}) spacer films in transistors are becoming ever more stringent as scaling of transistor structures continues. One method to deposit high-quality films with excellent control is atomic layer deposition (ALD). However, depositing SiN{sub x} by ALD has turned out to be very challenging. In this work, it is shown that the plasma gas residence time τ is a key parameter for the deposition of SiN{sub x} by plasma-assisted ALD and that this parameter can be linked to a so-called “redeposition effect”. This previously ignored effect, which takes place during the plasma step, is the dissociation of reaction products in the plasma and the subsequent redeposition of reaction-product fragments on the surface. For SiN{sub x} ALD using SiH{sub 2}(NH{sup t}Bu){sub 2} as precursor and N{sub 2} plasma as reactant, the gas residence time τ was found to determine both SiN{sub x} film quality and the resulting growth per cycle. It is shown that redeposition can be minimized by using a short residence time resulting in high-quality films with a high wet-etch resistance (i.e., a wet-etch rate of 0.5 nm/min in buffered HF solution). Due to the fundamental nature of the redeposition effect, it is expected to play a role in many more plasma-assisted ALD processes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗