Search NASA⌕ Search

SEARCH · Search NASA

Results for “diffusion processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Solar Drivers of 11-yr and Long-Term Cosmic Ray Modulation

In the current paradigm for the modulation of galactic cosmic rays (GCRs), diffusion is taken to be the dominant process during solar maxima while drift dominates at minima. Observations during the recent solar minimum challenge the pre-eminence of drift: at such times. In 2009, the approx.2 GV GCR intensity measured by the Newark neutron monitor increased by approx.5% relative to its maximum value two cycles earlier even though the average tilt angle in 2009 was slightly larger than that in 1986 (approx.20deg vs. approx.14deg), while solar wind B was significantly lower (approx.3.9 nT vs. approx.5.4 nT). A decomposition of the solar wind into high-speed streams, slow solar wind, and coronal mass ejections (CMEs; including postshock flows) reveals that the Sun transmits its message of changing magnetic field (diffusion coefficient) to the heliosphere primarily through CMEs at solar maximum and high-speed streams at solar minimum. Long-term reconstructions of solar wind B are in general agreement for the approx. 1900-present interval and can be used to reliably estimate GCR intensity over this period. For earlier epochs, however, a recent Be-10-based reconstruction covering the past approx. 10(exp 4) years shows nine abrupt and relatively short-lived drops of B to < or approx.= 0 nT, with the first of these corresponding to the Sporer minimum. Such dips are at variance with the recent suggestion that B has a minimum or floor value of approx.2.8 nT. A floor in solar wind B implies a ceiling in the GCR intensity (a permanent modulation of the local interstellar spectrum) at a given energy/rigidity. The 30-40% increase in the intensity of 2.5 GV electrons observed by Ulysses during the recent solar minimum raises an interesting paradox that will need to be resolved.

Cliver, E. W.↗
NASA NTRS1993

An extended laser flash technique for thermal diffusivity measurement of high-temperature materials

Knowledge of thermal diffusivity data for high-temperature materials (solids and liquids) is very important in analyzing a number of processes, among them solidification, crystal growth, and welding. However, reliable thermal diffusivity versus temperature data, particularly those for high-temperature liquids, are still far from complete. The main measurement difficulties are due to the presence of convection and the requirement for a container. Fortunately, the availability of levitation techniques has made it possible to solve the containment problem. Based on the feasibility of the levitation technology, a new laser flash technique which is applicable to both levitated liquid and solid samples is being developed. At this point, the analysis for solid samples is near completion and highlights of the technique are presented here. The levitated solid sample which is assumed to be a sphere is subjected to a very short burst of high power radiant energy. The temperature of the irradiated surface area is elevated and a transient heat transfer process takes place within the sample. This containerless process is a two-dimensional unsteady heat conduction problem. Due to the nonlinearity of the radiative plus convective boundary condition, an analytic solution cannot be obtained. Two options are available at this point. Firstly, the radiation boundary condition can be linearized, which then accommodates a closed-form analytic solution. Comparison of the analytic curves for the temperature rise at different points to the experimentally-measured values will then provide the thermal diffusivity values. Secondly, one may set up an inverse conduction problem whereby experimentally obtained surface temperature history is used as the boundary conditions. The thermal diffusivity can then be elevated by minimizing the difference between the real heat flux boundary condition (radiation plus convection) and the measurements. Status of an experimental study directed at measuring the thermal diffusivity of high-temperature solid samples of pure Nickel and Inconel 718 superalloys are presented. Preliminary measurements showing surface temperature histories are discussed.

Shen, F.↗
NASA NTRS1989

Investigation of an excited jet diffusion flame at elevated pressure

Experiments are carried out for studying the relationship between flow structure, flow excitation, and the reaction process in the near field of a low-speed coflowing jet diffusion flame. The effect of axial forcing and increasing pressure on the structure and controllability of the flame is studied to elucidate some of the underlying control mechanisms. The experiments are conducted in a variable-pressure flow facility permitting the study of reacting flows in the 10-1000 kPa (0.1-10 atm) pressure range. The flame is excited by a small-amplitude periodic fluctuation added to the central fuel jet exit velocity. Among the varied excitation frequencies employed, a narrow band is found in which several of the flow instabilities seem to be in coincidence, causing periodic breakup of the flame into a series of distinct eddies. This is called the strongly-coupled state. Effects of excitation frequencies at and above the strongly-coupled range are presented.

Strawa, Anthony W.↗
DOE OSTI2023

Parallel simulation via SPPARKS of on-lattice kinetic and Metropolis Monte Carlo models for materials processing

Abstract SPPARKS is an open-source parallel simulation code for developing and running various kinds of on-lattice Monte Carlo models at the atomic or meso scales. It can be used to study the properties of solid-state materials as well as model their dynamic evolution during processing. The modular nature of the code allows new models and diagnostic computations to be added without modification to its core functionality, including its parallel algorithms. A variety of models for microstructural evolution (grain growth), solid-state diffusion, thin film deposition, and additive manufacturing (AM) processes are included in the code. SPPARKS can also be used to implement grid-based algorithms such as phase field or cellular automata models, to run either in tandem with a Monte Carlo method or independently. For very large systems such as AM applications, the Stitch I/O library is included, which enables only a small portion of a huge system to be resident in memory. In this paper we describe SPPARKS and its parallel algorithms and performance, explain how new Monte Carlo models can be added, and highlight a variety of applications which have been developed within the code.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Commissioning of Robotic Inspection and Automated Analysis System for Assay of Gas Diffusion Piping - 19500

Robotic, in-pipe, nondestructive assay (NDA) is a revolutionary and important means for measuring, analyzing, and reporting radioactive holdup deposits in enrichment piping. This innovation promises vast advantages for efficiency, safety, and cost savings. Payoff, however, lies in utilization much more than innovation. Crossing that threshold from a technical capability to an everyday tool occurs only after rigorous commissioning, adoption, and infusion. This must meet the highest standard, and there can be no compromise. Certification of a new NDA technology must meet the highest standards for quality, safety, and efficacy. Prior to this work, there was no precedent of procedure and method for certification of a robotic methodology for this purpose. The best of robotics had not certified NDA. The best of NDA had not certified robotics. Hence, a great deal of discovery, resourcefulness, and collaboration contributed to this success. This paper chronicles the first-of-kind chartering, co-development, testing, documentation, and site integration that certified this trailblazing in-pipe, robotic NDA. Commissioning had to demonstrate and certify end-to-end NDA automation from robot traversal to computer analysis to report generation of contaminated process piping at the Portsmouth, Ohio gaseous diffusion facility. This was a rigorous campaign of tests, evaluations, and documentation. Highlights included multiple tests in four elevated pipes exercised the gamut of NDA and robotic capabilities. Each of the four test pipes presented a unique loading of U-235. The tests demonstrated operations in both 30- inch and 42-inch diameter pipes with varying lengths and terminated by a variety of valves and fittings. Tests in a fifth pipe at floor level demonstrated deployment and applicability for pipes at this ground height and robot recognition of another fitting type. All operations, calibration, deployment, auto-reporting, and analysis were handled by Portsmouth site personnel. These tests concluded a series of component-level acceptance tests which certified all constituent technologies and operational features. Test metrics included comparison of reported to ground truth results and assessment of data quality from quality assurance and replicate measurement comparison. Beyond the radiometry associated with any NDA method, this unique commissioning path exercised and evaluated all the robotic features that are intrinsic to automation. These include odometry, geometric modeling, autonomy, remote launch and recovery, and end-to-end data flow. Each of these required verification and certification. These evaluations were first-of-kind for the decommissioning community, requiring innovation and resourcefulness in their own right. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Coalescence dynamics of prismatic dislocation loops due to vacancy supersaturation

Recovery processes in metals with a high defect concentration are at the heart of a structural alloy's usability in engineering applications. However, such processes take place via nonconservative mechanisms mediated by point defect diffusion and are governed by their interactions with the underlying microstructure. Indeed, one of the main challenges in studying recovery processes is their intrinsic multiscale complexity, which often negates the direct use of experimental techniques. Here, in this Research Letter, we study the mechanism of dislocation loop coalescence in metals by simulating the interaction dynamics between vacancies and prismatic loops using a stochastic framework that seamlessly bridges point defect kinetics with dislocation mechanics. Our simulations reveal two fundamental discoveries: first, that climb processes are governed by local fluctuations that are not captured by continuum elastodiffusion models, and, second, that prismatic loops create internal traps for vacancies, leading to the formation of rings around the perimeter of the loops that affect how coalescence takes place. Our results show an excellent agreement with in situ experimental observations of loop coalescence in Fe under irradiation.

36 MATERIALS SCIENCE↗
NASA NTRS1977

Laser-zone growth in a Ribbon-To-Ribbon (RTR) process. Silicon sheet growth development for the large area silicon sheet task of the low cost silicon solar array project

The Ribbon-to-Ribbon (RTR) approach to silicon ribbon growth is investigated. An existing RTR apparatus is to be upgraded to its full capabilities and operated routinely to investigate and optimize the effects of various growth parameters on growth results. A new RTR apparatus was constructed to incorporate increased capabilities and improvements over the first apparatus and to be capable of continuous growth. New high power lasers were implemented and this led to major improvements in growth velocity -- 4 inch/min. growth has been demonstrated. A major step in demonstration of the full feasibility of the RTR process is reported in the demonstration of RTR growth from CVD polyribbon rather than sliced polyribbon ingots. Average solar cell efficiencies of greater than 9% and a best cell efficiency of 11.7% are reported. Processing was shown to provide a substantial improvement in material minority carrier diffusion length. An economic analysis is reported which treats both the polyribbon fabrication and RTR processes.

Gurtler, R. W.↗
NASA NTRS1994

An extended source for CN jets in Comet P/Halley

We examined radial intensity profiles of CN jets in comparison with the diffuse, isotropic component of the CN coma of Comet P/Halley. All images were bias-subtracted, flat-fielded, and continuum-subtracted. We calculated the diffuse profiles by finding the azimuthal mean of the coma least contaminated by jets yielding profiles similar to those of vectorial and Haser models of simple photodissociation. We found the jet profiles by calculating a mean around a Gaussian-fitted center in r-theta space. There is an unmistakable difference between the profiles of the CN jets and the profiles of the diffuse CN. Spatial derivatives of these profiles, corrected for geometrical expansion, show that the diffuse component is consistent with a simple photodissociation process, but the jet component is not. The peak production of the jet profile occurs 6000 km from the nucleus at a heliocentric distance of 1.4 AU. Modeling of both components of the coma indicate results that are consistent with the diffuse CN photochemically produced, but the CN jets need an additional extended source. We found that about one-half of the CN in the coma of Comet P/Halley originated from the jets, the rest from the diffuse component. These features, along with the width of the jet being approximately constant, are consistent with a CHON grain origin for the jets.

Klavetter, James Jay↗
NASA NTRS1994

Mathematical Model for the Mineralization of Bone

A mathematical model is presented for the transport and precipitation of mineral in refilling osteons. One goal of this model was to explain calcification 'halos,' in which the bone near the haversian canal is more highly mineralized than the more peripheral lamellae, which have been mineralizing longer. It was assumed that the precipitation rate of mineral is proportional to the difference between the local concentration of calcium ions and an equilibrium concentration and that the transport of ions is by either diffusion or some other concentration gradient-dependent process. Transport of ions was assumed to be slowed by the accumulation of mineral in the matrix along the transport path. The model also mimics bone apposition, slowing of apposition during refilling, and mineralization lag time. It was found that simple diffusion cannot account for the transport of calcium ions into mineralizing bone, because the diffusion coefficient is two orders of magnitude too low. If a more rapid concentration gradient-driven means of transport exists, the model demonstrates that osteonal geometry and variable rate of refilling work together to produce calcification halos, as well as the primary and secondary calcification effect reported in the literature.

Martin, Bruce↗
NASA NTRS1994

Mathematical Model for the Mineralization of Bone

A mathematical model is presented for the transport and precipitation of mineral in refilling osteons. One goal of this model was to explain calcification 'halos,' in which the bone near the haversian canal is more highly mineralized than the more peripheral lamellae, which have been mineralizing longer. It was assumed that the precipitation rate of mineral is proportional to the difference between the local concentration of calcium ions and an equilibrium concentration and that the transport of ions is by either diffusion or some other concentration gradient-dependent process. Transport of ions was assumed to be slowed by the accumulation of mineral in the matrix along the transport path. ne model also mimics bone apposition, slowing of apposition during refilling, and mineralization lag time. It was found that simple diffusion cannot account for the transport of calcium ions into mineralizing bone, because the diffusion coefficient is two orders of magnitude too low. If a more rapid concentration gradient-driven means of transport exists, the model demonstrates that osteonal geometry and variable rate of refilling work together to produce calcification halos, as well as the primary and secondary calcification effect reported in the literature.

Martin, Bruce↗
DOE OSTI2019

Evaluation of Superconducting Properties and Diffusion Behavior of Ex Situ and In Situ Bulk MgB{sub 2} Materials with Ni Coating

Ex situ and in situ bulk MgB{sub 2} superconducting materials have successfully been produced by the simple amorphous boron and nano-amorphous boron powders with the processes of ball milling, pressing, and annealing. The superconducting properties and diffusion behavior of MgB{sub 2} samples after nickel (Ni) coating process have been characterized and compared to the microstructure and performance of uncoated (bare) MgB{sub 2} bulk sample. One surface of MgB{sub 2} superconductor sample was coated with a thin Ni layer of about 50 − 60μm thickness using vapor deposition techniques in versatile high vacuum coater, then every sample was annealed at temperatures between 923 and 1123 K for 1 h. The role of annealing temperature on physical, electrical, superconducting, and structural characterizations of bare and Ni-coated ex situ/in situ MgB{sub 2} bulk superconductors has been studied using X-ray diffraction and dc electrical resistivity versus temperature measurements. Finally, the Ni diffusion coefficients (D{sub Ni} = D{sub 0}exp(E/k{sub B}T)) are calculated in the temperature range to calculate the required minimum activation energy value for the Ni atoms/ions into the ex situ MgB{sub 2} crystal structure for the first time.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2010

The Landsat Data Continuity Mission Operational Land Imager (OLI) Radiometric Calibration

The Operational Land Imager (OLI) on the Landsat Data Continuity Mission (LDCM) has a comprehensive radiometric characterization and calibration program beginning with the instrument design, and extending through integration and test, on-orbit operations and science data processing. Key instrument design features for radiometric calibration include dual solar diffusers and multi-lamped on-board calibrators. The radiometric calibration transfer procedure from NIST standards has multiple checks on the radiometric scale throughout the process and uses a heliostat as part of the transfer to orbit of the radiometric calibration. On-orbit lunar imaging will be used to track the instruments stability and side slither maneuvers will be used in addition to the solar diffuser to flat field across the thousands of detectors per band. A Calibration Validation Team is continuously involved in the process from design to operations. This team uses an Image Assessment System (IAS), part of the ground system to characterize and calibrate the on-orbit data.

Markham, Brian L.↗
NASA NTRS1992

Co diffusion and growth of buried single-crystal CoSi2 in Si(111) by endotaxy

At a growth temperature of 800 C, Co deposited on a Si capping layer exhibits oriented growth on buried CoSi2 grains on Si(111), a process referred to as endotaxy. This occurs preferentially to surface nucleation of CoSi2, provided the thickness of the Si cap is less than a critical value of about 100 nm for deposition rates of 0.003-0.01 nm/s. The steady-state process is modeled using known values of the Co diffusion coefficient and solid solubility in Si, allowing some conclusions to be drawn regarding parameters relevant to CoSi2 epitaxy. Using this technique, single-crystal continuous layers of CoSi2 can be formed under a high-quality Si capping layer.

Fathauer, R. W.↗
DOE OSTI2021

Experimental and numerical study of the effects of solution concentration and temperature on concrete under external sulfate attack

The work reports on an experimental programme, conducted to validate comprehensively our previously proposed coupled chemo-transport model for external sulfate attack on concrete. Specifically, the effects of the concentration of sulfate solution and temperature on the distribution of sulfate ions in concrete are experimentally investigated and used to demonstrate the accuracy of the modeling framework. Further, the profile of aluminate depletion and the leaching depth numerically are investigated. For all cases the model predictions are in good agreement with the experimental results, showing increases of the concentration of sulfate ions in concrete with higher concentrations of sulfate solution and higher temperatures. It is concluded that higher sulfate solution concentration and temperature enhance the processes involved in the external sulfate attack on concrete, namely diffusion of sulfate ions and their chemical reactions with concrete. It is found that these parameters affect the external sulfate attack predominantly via the chemical reaction process.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Estimates of climate system properties incorporating recent climate change

Abstract. Historical time series of surface temperature and ocean heat content changes are commonly used metrics to diagnose climate change and estimate properties of the climate system. We show that recent trends, namely the slowing of surface temperature rise at the beginning of the 21st century and the acceleration of heat stored in the deep ocean, have a substantial impact on these estimates. Using the Massachusetts Institute of Technology Earth System Model (MESM), we vary three model parameters that influence the behavior of the climate system: effective climate sensitivity (ECS), the effective ocean diffusivity of heat anomalies by all mixing processes (Kv), and the net anthropogenic aerosol forcing scaling factor. Each model run is compared to observed changes in decadal mean surface temperature anomalies and the trend in global mean ocean heat content change to derive a joint probability distribution function for the model parameters. Marginal distributions for individual parameters are found by integrating over the other two parameters. To investigate how the inclusion of recent temperature changes affects our estimates, we systematically include additional data by choosing periods that end in 1990, 2000, and 2010. We find that estimates of ECS increase in response to rising global surface temperatures when data beyond 1990 are included, but due to the slowdown of surface temperature rise in the early 21st century, estimates when using data up to 2000 are greater than when data up to 2010 are used. We also show that estimates of Kv increase in response to the acceleration of heat stored in the ocean as data beyond 1990 are included. Further, we highlight how including spatial patterns of surface temperature change modifies the estimates. We show that including latitudinal structure in the climate change signal impacts properties with spatial dependence, namely the aerosol forcing pattern, more than properties defined for the global mean, climate sensitivity, and ocean diffusivity.

Libardoni, Alex G.↗
DOE OSTI2021

Estimating the Diffusion Coefficient of Lithium in Graphite: Extremely Fast Charging and a Comparison of Data Analysis Techniques

Galvanostatic intermittent titration experiments were performed in three-electrode cells to characterize the effect of C/2, 2-C and 4-C charge rates on the observed lithium diffusion coefficient. As part of the data analysis process, we compared the classic Weppner-Huggins analysis of polarization data with a newer (Wang et al.) analysis method for depolarization data. At low values of x in Li x C 6 , both analysis methods showed the same general trend in the apparent lithium diffusion coefficient, 4-C > 2-C > C/2. The two techniques differed in the magnitude of the estimated diffusion coefficient by about a factor of 100. The observed increase in diffusion coefficient does not last over a large compositional range. Since the estimates from the method of Weppner and Huggins may contain artifacts due to the use of particulate electrodes and high charge rates, the method of Wang et al. may produce better values.

25 ENERGY STORAGE↗
DOE OSTI2022

Bilayer hybrid graphite anodes via freeze tape casting for extreme fast charging applications

Extreme fast charging (XFC) of lithium-ion batteries is critical for continuous market adoption of electric vehicles. However, mass transport limitations and sluggish kinetics lead to lithium plating in graphite anodes under fast charging conditions. One approach to address the mass transport limitation in graphite is to design low-tortuosity electrodes to enhance ionic transport. In this study, a bilayer hybrid structured electrode with directionally aligned channels was developed via freeze tape casting, which enables faster lithium ion diffusion through the graphite electrode. A scalable roll-to-roll process was designed in which slurry can be cast on any substrates for simple processing. Additionally, electrochemical impedance spectroscopy measurements indicated that the bilayer hybrid coating had both low tortuosity and short diffusion pathways, enabling XFC charging. Rate testing for the bilayer hybrid electrode indicated superior performance over the other coatings, exhibiting a ~20% improvement in the charge capacity compared with the conventional coating at 5C and 10 min total charging time. The bilayer hybrid electrode also demonstrated a 10% improvement in capacity retention compared with the conventional electrode after 1000 cycles at XFC conditions. This study demonstrates freeze tape casting as a scalable way to fabricate low-tortuosity electrodes for XFC applications.

25 ENERGY STORAGE↗
NASA NTRS1980

The effects of titanium impurities in N/+//P silicon solar cells

Microscopic and electrical measurements were performed to explain the degradation mechanisms associated with the presence of titanium impurities in silicon. The measurements included X-ray topography, transmission electron microscopy, and deep level transient spectroscopy, before and after processing. The results indicated the presence of TiO2 precipitates, the density of which increased after phosphorus diffusion. A majority carrier trapping level was observed in the wafers before processing. It was concluded that 10% of the Ti in the N(+)/P silicon solar cells formed electrically active centers which caused degradation of the cell junction. 14% of the remaining Ti precipitated out as TiO2, forming electrically active defects, which also caused junction degradation.

Salama, A. M.↗