Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Atomistic Investigation of Plastic Deformation and Dislocation Motion in Uranium Mononitride

Uranium mononitride (UN) is a promising advanced nuclear fuel due to its high thermal conductivity and high fissile density. However, many aspects of its mechanical behavior, particularly at reactor-relevant conditions, remain unclear. In this study, molecular dynamics (MD) simulations were employed to investigate the deformation behavior and dislocation motion in UN. We found that the Kocevski potential predicts the principal slip system as $\frac{1}{2}$ $\langle110\rangle${110}, aligning with experimental data. On the other hand, the Tseplyaev potential predicts slip to primarily occur on $\frac{1}{2}$ $\langle110\rangle${111}. MD simulations of stress–strain behavior were used to estimate the nanoindentation hardness, revealing that the Kocevski potential accurately predicts hardness even though it fails to model dynamic plasticity. Complete dislocation mobility functions have been fitted for the edge and screw dislocations in both the thermally activated and phonon-drag regimes. The 300 K linear mobility of the edge dislocation using the Tseplyaev potential was found to be 817 Pa -1 ·s -1 , whereas that of the screw dislocation using the Kocevski potential was found to be 4546 Pa -1 ·s -1 . At intermediate stresses, we observed that the subsonic steady-state motion of the edge dislocation in UN is intermittently interrupted by velocity jumps, reaching the average sound velocity. Finally, the threshold Schmid stress is calculated as 179–197 MPa, which gives an upper-limit estimate of the uniaxial yield stress of polycrystalline UN of 548–603 MPa. These findings, including the fitted dislocation mobility function, provide essential input for future plasticity and dislocation dynamics models of nuclear fuels.

36 MATERIALS SCIENCE↗

Fast Assessment of Metal Performance through Dislocation Physics and Machine Learning

The microstructure of metals is key to their mechanical properties. The types, density, composition and morphology of crystal defects all have pronounced impact on the properties. Changes to the microstructure occurring during processing and use can be very striking. The emerging technology additive manufacturing (AM) has the potential to improve performance by allowing optimized designs, but the process and environments can lead to unusual microscale features whose properties must be understood and characterized to enable higher technological readiness levels and application. Experimentally, an extensive evaluation of mechanical properties of 3D printed metals is a challenge, and anomalous effects related to the AM process add complexity. We present a new machine learning (ML) model predicting mechanical response based on dislocation mediated plasticity simulations. A large set of 3D discrete dislocation dynamics simulations with wide ranges of loading conditions is transformed to preprocessed data ready for training with the ML model. The trained model can predict the mechanical response of Mo30W for a given microstructure evolution, providing key information essential for optimization of AM processing.

Jaehyun Cho↗

Fast Assessment of Metal Performance through Dislocation Physics and Machine Learning

The microstructure of metals is key to their mechanical properties. The types, density, composition and morphology of crystal defects all have pronounced impact on the properties. Changes to the microstructure occurring during processing and use can be very striking. The emerging technology additive manufacturing (AM) has the potential to improve performance by allowing optimized designs, but the process and environments can lead to unusual microscale features whose properties must be understood and characterized to enable higher technological readiness levels and application. Experimentally, an extensive evaluation of mechanical properties of 3D printed metals is a challenge, and anomalous effects related to the AM process add complexity. We present a new machine learning (ML) model predicting mechanical response based on dislocation mediated plasticity simulations. A large set of 3D discrete dislocation dynamics simulations with wide ranges of loading conditions is transformed to preprocessed data ready for training with the ML model. The trained model can predict the mechanical response of Mo30W for a given microstructure evolution, providing key information essential for optimization of AM processing.

Jaehyun Cho↗

In situ electron microscopy studies of electromechanical behavior in metals at the nanoscale using a novel microdevice-based system

Electrically assisted deformation (EAD) is an emerging technique to enhance formability of metals by applying an electric current through them. Despite its increasing importance in manufacturing applications, there is still an unresolved debate on the nature of the fundamental deformation mechanisms underlying EAD, mainly between electroplasticity (non-thermal effects) and resistive heating (thermal effects). This status is due to two critical challenges: (1) a lack of experimental techniques to directly observe fundamental mechanisms of material deformation during EAD, and (2) intrinsic coupling between electric current and Joule heating giving rise to unwanted thermally activated mechanisms. To overcome these challenges, we have developed a microdevice-based electromechanical testing system (MEMTS) to characterize nanoscale metal specimens in transmission electron microscopy (TEM). Our studies reveal that MEMTS eliminates the effect of Joule heating on material deformation, a critical advantage over macroscopic experiments, owing to its unique scale. For example, a negligible change in temperature (<0.02 °C) is predicted at ∼3500 A/mm{sup 2}. Utilizing the attractive features of MEMTS, we have directly investigated potential electron-dislocation interactions in single crystal copper (SCC) specimens that are simultaneously subjected to uniaxial loading and electric current density up to 5000 A/mm{sup 2}. Our in situ TEM studies indicate that for SCC, electroplasticity does not play a key role as no differences in dislocation activities, such as depinning and movement, are observed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Thermal stability of sputter deposited nanomosaic rutile TiO{sub 2}

A domain structure based on the rutile lattice with a large density of (1/2)<011>{l_brace}011{r_brace}-type stacking faults is found in sputter deposited TiO{sub 2} films [J. Vac. Sci. Technol. A 24, 2054 (2006)]. The thermal stability of nanomosaic rutile at moderate temperature is reported here. Films are annealed at 973 K for 0.25-15 h, characterized by x-ray diffraction. A Johnson-Mehl-Avrami-Kolmogorov analysis indicates impeded crystallite growth. A dislocation-locking mechanism is proposed for this behavior. Partial dislocations with (1/2)<011> Burgers vectors that bound the stacking faults glide on intersecting {l_brace}011{r_brace} slip planes and react to produce sessile stair rod dislocations. Without the high temperature required for dislocation climb, (1/2)<011>{l_brace}011{r_brace}-type faults inherent to nanomosaic rutile provide thermal stability against massive crystallite growth.

36 MATERIALS SCIENCE↗

Rapid trench initiated recrystallization and stagnation in narrow Cu interconnect lines

Understanding and ultimately controlling the self-annealing of Cu in narrow interconnect lines has remained a top priority in order to continue down-scaling of back-end of the line interconnects. Recently, it was hypothesized that a bottom-up microstructural transformation process in narrow interconnect features competes with the surface-initiated overburden transformation. Here, a set of transmission electron microscopy images which captures the grain coarsening process in 48 nm lines in a time resolved manner is presented, supporting such a process. Grain size measurements taken from these images have demonstrated that the Cu microstructural transformation in 48 nm interconnect lines stagnates after only 1.5 h at room temperature. This stubborn metastable structure remains stagnant, even after aggressive elevated temperature anneals, suggesting that a limited internal energy source such as dislocation content is driving the transformation. As indicated by the extremely low defect density found in 48 nm trenches, a rapid recrystallization process driven by annihilation of defects in the trenches appears to give way to a metastable microstructure in the trenches.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A nanoscale duplex precipitation approach for improving the properties of Fe-base alloys

The precipitate size and number density are important factors for tailoring the mechanical behaviors of nanoscale precipitate-hardened alloys. However during thermal aging, the precipitate size and number density change leading to either poor strength or high strength but significantly reduced ductility. Here we demonstrate, by producing nanoprecipitates with unusual duplex structures in a composition-optimized multicomponent precipitation-hardened alloy, a unique approach to improve the stability of the alloy against the effects of thermal aging and consequently change in the mechanical properties. Our study provides compelling experimental evidence that these nanoscale precipitates consist of a duplex structures with a Cu-enriched bcc core that is partially encased by a B2-ordered Ni(Mn,Al) phase. This duplex structure enables the precipitate size and number density to be independently optimized, provides a more complex obstacle for dislocation movement due to the ordering and an additional interphase interface, and yields a high yield strength alloy without sacrificing the ductility.

Zhang, Zhongwu↗

Mechanics of point defect diffusion near dislocations and grain boundaries: A chemomechanical framework

Diffusion of point defects during irradiation is simulated via a two-way coupling between mechanical stress and defect diffusion in iron. This diffusion is based on a modified chemical potential that includes not only the local concentration of radiation-induced defects, but also the influence of the residual stress field from both the microstructure (i.e. dislocations or grain boundaries) and the eigenstrain caused by the defects themselves. Defect flux and concentration rates are derived from this chemical potential using Fick’s first and second laws. Mean field rate theory is incorporated to model the annihilation of Frenkel pairs, and increased annihilation near grain boundaries is included based on the elastic energy of each grain boundary. Mechanical equilibrium is coupled with diffusion by computing eigenstrain from point defects and adding this to the total strain. Intrinsic stresses associated with the dislocations and grain boundaries are calculated using dislocation and disclination mechanics. Through this two-way-coupled model, regions of low concentration are seen near grain boundaries, and sink efficiency is calculated for different types of microstructure. Furthermore, the results show that the two-way mechanical coupling has a strong influence on sink efficiency for dislocation loops. The results also suggest that misorientation is a poor metric for determining sink efficiency, with sink density and elastic energy being much more informative.

36 MATERIALS SCIENCE↗

In situ study on radiation response of tungsten manufactured by laser powder bed fusion

Tungsten (W) produced by laser powder bed fusion (LPBF) was examined by in situ Krypton (Kr) ion irradiation at 400 °C up to 2.52 displacements per atom (dpa) to investigate its radiation response. Dislocation loops with identical Burgers vectors form aligned raft structures, inducing significant grain misorientation accumulation. Defect saturation was observed beyond 0.36 dpa, marked by constant loop density and raft spacing. WO 3 nanoparticles are found in the as-printed matrix and served as efficient defect sinks. Dislocation loops were absorbed at the W/WO 3 interface, facilitating defect annihilation and suppressing defect accumulation. In conclusion, these findings highlight the role of LPBF microstructure and oxide interfaces in mediating radiation-induced defect evolution, offering insights for designing radiation tolerant W-based materials.

Defect sink↗

He Transport and Fate of Tempered Martensitic Steels: Summary of Recent TEM Observations

As an extension of prior work, we summarize recent observations made on a He-implanted tempered martensitic steel (TMS), F82H mod 3, irradiated in the HFIR, in both as-tempered (AT) and cold-worked (CW) conditions. A novel implantation technique was used to uniformly inject He into 3-mm diameter TEM discs to depths ranging from ≈ 5-8 µm. The He is generated by two-step transmutation reactions in Ni contained in a NiAl coating layer adjacent to paired 3 mm TEM discs. NiAl layers from 1 to 4 μm thick produced He/dpa ratios between 5 and 40 appm/dpa. The irradiations were at temperatures of 300, 400 and 500°C from 3.9 to 9 dpa and 90 to 380 appm He. Electron transparent samples were prepared by a cross-sectional thinning technique that allowed investigating microstructural evolution over a range of implantation depths. Irradiation of the AT alloy to 9 dpa at 500°C and 380 appm He resulted in relatively large, faceted cavities, that are likely voids, along with a much higher density of smaller He bubbles. The cavities were most often aligned in pearl necklace like strings, presumably due to their formation on pre-existing dislocations. A finer distribution of cavities was also present on precipitate interfaces, lath and grain boundaries. Nine dpa irradiations that produced 190 appm He resulted in a somewhat more random distribution and lower density of smaller matrix cavities; but lower He levels had a less noticeable effect on bubbles in the lath and precipitate boundaries. Corresponding irradiations of the CW F82H produced a larger number of smaller cavities. Irradiation of the AT alloy to 3.9 dpa and 90 ppm He at 400°C produced a similar cavity population to that observed at 500°C at 190 appm He, while the corresponding cavities at 500°C are slightly larger and more numerous at 380 appm He. The cavity strings were less obvious for the 400°C irradiations, and the bubble distribution appeared to be more random. No cavities were observed in the case of the 300°C irradiations. Overall the cavity number densities compare favorably with those previously reported, but details, including size distributions, are still under investigation. Dislocation structures were complex and varied greatly as a function of irradiation dose and temperature, and will be more thoroughly characterized in the next phase of the work.

Edwards, Danny J.↗

Dynamic phases, pinning, and pattern formation for driven dislocation assemblies

We examine driven dislocation assemblies and show that they can exhibit a set of dynamical phases remarkably similar to those of driven systems with quenched disorder such as vortices in superconductors, magnetic domain walls, and charge density wave materials. These phases include pinned-jammed, fluctuating, and dynamically ordered states, and each produces distinct dislocation patterns as well as specific features in the noise fluctuations and transport properties. Lastly, our work suggests that many of the results established for systems with quenched disorder undergoing plastic depinning transitions can be applied to dislocation systems, providing a new approach for understanding pattern formation and dynamics in these systems.

36 MATERIALS SCIENCE↗

Overcoming diffusion-related limitations in semiconductor defect imaging with phonon-plasmon-coupled mode Raman scattering

Carrier diffusion is of paramount importance in many semiconductor devices, such as solar cells, photodetectors, and power electronics. Structural defects prevent such devices from reaching their full performance potential. Although a large carrier diffusion length indicates high material quality, it also implies increased carrier depletion by an individual extended defect (for instance, a dislocation) and obscures the spatial resolution of neighboring defects using optical techniques. For commonly utilized photoluminescence (PL) imaging, the spatial resolution is dictated by the diffusion length rather than by the laser spot size, no matter the spot is at or below the diffraction limit. We show how Raman imaging of the LO phonon-plasmon-coupled mode can be used to recover the intrinsic spatial resolution of the optical system, and we demonstrate the effectiveness of the technique by imaging defects in GaAs with diffraction-limited optics, achieving a 10-fold improvement in resolution. Furthermore, by combining Raman and PL imaging, we can independently and simultaneously determine the spatial dependence of the electron density, hole density, radiative recombination rate, and non-radiative recombination rate near a dislocation-like defect, which has not been possible using other techniques.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Towards Ab-Initio Simulations of Crystalline Defects at the Exascale Using Spectral Quadrature Density Functional Theory

Defects in crystalline solids play a crucial role in determining properties of materials at the nano, meso- and macroscales, such as the coalescence of vacancies at the nanoscale to form voids and prismatic dislocation loops or diffusion and segregation of solutes to nucleate precipitates, phase transitions in magnetic materials via disorder and doping. First principles Density Functional Theory (DFT) simulations can provide a detailed understanding of these phenomena. However, the number of atoms needed to correctly simulate these systems is often beyond the reach of many widely used DFT codes. The aim of this article is to discuss recent advances in first principles modeling of crystal defects using the spectral quadrature method. The spectral quadrature method is linear scaling with respect to the number of atoms, permits spatial coarse-graining, and is capable of simulating non-periodic systems embedded in a bulk environment, which allows the application of appropriate boundary conditions for simulations of crystalline defects. In this article, we discuss the state-of-the-art in ab-initio modeling of large metallic systems of the order of several thousand atoms that are suitable for utilizing exascale computing resourses.

36 MATERIALS SCIENCE↗

Steps in Solution Growth: Revised Gibbs-Thomson Law, Turbulence and Morphological Stability

Two groups of new phenomena revealed by AFM and high resolution optical interferometry on crystal faces growing from solutions will be discussed. 1. Spacing between strongly polygonized spiral steps with low less than 10(exp -2) kink density on lysozyme and K- biphtalate do not follow the Burton-cabrera-Frank theory. The critical length of the yet immobile first Short step segment adjacent to a pinning defect (dislocation, stacking fault) is many times longer than that following from the step free energy. The low-kink density steps are typical of many growth conditions and materials, including low temperature gas phase epitaxy and MBE. 2. The step bunching pattern on the approx. 1 cm long { 110) KDP face growing from the turbulent solution flow (Re (triple bonds) 10(exp 4), solution flow rate approx. 1 m/s) suggests that the step bunch height does not increase infinitely as the bunch path on the crystal face rises, as is usually observed on large KDP crystals. The mechanism controlling the maximal bunch width and height is based on the drag of the solution depleted by the step bunch down thc solution stream. It includes splitting, coagulation and interlacing of bunches

Chernov, A. A.↗

Combined effect of injected interstitials and He implantation, and cavities inside dislocation loops in high purity Fe-Cr alloys

High purity Fe-Cr alloys with Cr content ranging from 3 to 14 wt% were irradiated by self-ions at 500 °C in dual-beam mode up to 157 displacements per atom (dpa), 17 appm He/dpa. Transmission electron microscopy (TEM) on focused ion beam foils revealed the depth distribution of irradiation induced cavities and dislocation loops. A detailed quantitative analysis of cavity microstructure was performed on Fe14%Cr, while Fe(3, 5, 10, 12)%Cr were analyzed qualitatively. A homogeneous distribution of small cavities were observed up to the damage peak. From surface to the damage peak, cavity number density increased almost linearly. The cavity microstructure changed drastically at and after the damage peak, where the size increased and number density decreased. Most notably, the microstructure consisted of a striking mixture of heterogeneously nucleated cavities inside dislocation loops and freely nucleated cavities in the matrix. Further, the depth-dependent void swelling increased continuously along the damage depth. This contrasts with most ion irradiation results where suppression of void swelling occurs adjacent to the damage peak due the injected interstitial effect. We hypothesize a plausible mechanism of the observed swelling variation based on a combined effect of the injected interstitials and helium implantation near the damage peak by comparing the results with those in pure iron irradiated under same conditions. This synergistic effect may develop cavity microstructures which do not necessarily reflect microstructures expected due to injected interstitial effect and can be easily wrongly interpreted. The depth dependent dislocation loop microstructure was studied qualitatively in Fe14%Cr sample. Up to the damage peak, a complex dense network of dislocations formed due to the interaction/impingement of the dislocation loops. Individually resolvable loops were only observed after the damage peak, where their association with cavities was noted. Furthermore helium also induced heterogeneous cavity nucleation on dislocations constituting a grain boundary and on pre-existing dislocation lines.

36 MATERIALS SCIENCE↗

High Carrier Lifetimes in Epitaxial Germanium-Tin/Al(In)As Heterostructures with Variable Tin Compositions

Group IV-based germanium-tin (Ge1-ySny) compositional materials have recently shown great promise for infrared detection, light emission and ultra-low power transistors. High carrier lifetimes are desirable for enhancing the detection limit and efficiency of photodetectors, low threshold current density in lasers, and low tunneling barrier height by lowering defects and dislocations at the heterointerface of a source and a channel. Here, carrier lifetimes in epitaxial germanium (Ge) and variable tin (Sn) compositional Ge1-ySny materials were experimentally determined on GaAs substrates using the contactless microwave photoconductive decay (u-PCD) technique at an excitation wavelength of 1500 nm. Sharp (2 x 2) reflection high energy electron diffraction patterns and low surface roughness were observed from the surface of the Ge0.97Sn0.03 epilayer. X-ray rocking curves from Ge0.97Sn0.03 and Ge0.94Sn0.06 layers demonstrated the pseudomorphic and lattice-matched growth on AlAs and In0.12Al0.88As buffers, respectively, further substantiated by reciprocal space maps and abrupt heterointerfaces evident from the presence of Pendellosung oscillations. High effective carrier lifetimes of 150 ns to 450 ns were measured for Ge1-ySny epilayers as a function of Sn composition, surface roughness, growth temperature, and layer thickness. The observed increase in the carrier lifetime with an increasing Ge layer thickness and a reducing surface roughness, by incorporating Sn, were explained. The enhancement of the carrier lifetime with an increasing Sn concentration was achieved by controlling the defects with lattice-matched Ge0.94Sn0.06/In0.12Al0.88As heterointerfaces or the pseudomorphic growth of Ge0.94Sn0.06 on GaAs. Therefore, our monolithic integration of variable Sn alloy compositional Ge1-ySny materials with high carrier lifetimes opens avenues to realize electronic and optoelectronic devices.

carrier lifetimes↗

Development of “GaSb-on-silicon” metamorphic substrates for optoelectronic device growth

The epitaxial development and characterization of metamorphic “GaSb-on-silicon” buffers as substrates for antimonide devices is presented. The approach involves the growth of a spontaneously and fully relaxed GaSb metamorphic buffer in a primary epitaxial reactor, and use of the resulting “GaSb-on-silicon” wafer to grow subsequent layers in a secondary epitaxial reactor. The buffer growth involves four steps—silicon substrate preparation for oxide removal, nucleation of AlSb on silicon, growth of the GaSb buffer, and finally capping of the buffer to prevent oxidation. This approach on miscut silicon substrates leads to a buffer with negligible antiphase domain density. The growth of this buffer is based on inducing interfacial misfit dislocations between an AlSb nucleation layer and the underlying silicon substrate, which results in a fully relaxed GaSb buffer. A 1 μm thick GaSb layer buffer grown on silicon has ~9.2 × 10 7 dislocations/cm 2 . The complete lack of strain in the epitaxial structure allows subsequent growths to be accurately lattice matched, thus making the approach ideal for use as a substrate. Here we characterize the GaSb-on-silicon wafer using high-resolution x-ray diffraction and transmission electron microscopy. The concept’s feasibility is demonstrated by growing interband cascade light emitting devices on the GaSb-on-silicon wafer. The performance of the resulting LEDs on silicon approaches that of counterparts grown lattice matched on GaSb.

36 MATERIALS SCIENCE↗

Micropipe Dissociation through Thick n+ Buffer Layer Growth

Thick (> 25 {mu}m) 4H n+ epitaxial layer growth was performed on 4H n+ substrates utilizing chlorine containing etch chemistries in a hot wall CVD system. Optimization of the n+ epitaxial layer growth was achieved by varying C/Si ratio and N2 flow. Desired epitaxial layers have doping levels > 5x1018 cm-3, epitaxial surface roughness <10 nm on a 20x20 {mu}m area and overall micropipe density reduction. To confirm the conversion of micropipes into closed core screw dislocations, microscopic examination of the epitaxial and wafer surfaces was carried out after KOH etching. Grazing incidence x-ray topography (XRT) as well as cross sectional XRT and microscopy were also performed. The cross sectional evaluation showed that the dissociation of the micropipes occurs very close to the epitaxy/wafer interface.

36 MATERIALS SCIENCE↗