Search NASA⌕ Search

SEARCH · Search NASA

Results for “dynamical model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Engine identification for adaptive control

An attempt to obtain a dynamic model for a turbofan gas turbine engine for the purpose of adaptive control is described. The requirements for adaptive control indicate that a dynamic model should be identified from data sampled during engine operation. The dynamic model identified was of the form of linear differential equations with time varying coefficients. A turbine engine is, however, a highly nonlinear system, so the identified model would be valid only over a small area near the operating point, thus requiring frequent updating of the coefficients in the model. Therefore it is necessary that the identifier use only recent information to perform its function. The identifier selected minimized the square of the equation errors. Known linear systems were used to test the characteristics of the identifier. It was found that the performance was dependent on the number of data points used in the computations and upon the time interval over which the data points were obtained. Preliminary results using an engine deck for the quiet, clean, shorthaul experimental engine indicate that the identified model predicts the engine motion well when there is sufficient dynamic information, that is when the engine is in transient operation.

Leonard, R. G.↗

Recovering the phase and amplitude of X-ray FEL pulses using neural networks and differentiable models

Dynamics experiments are an important use-case for X-ray free-electron lasers (XFELs), but time-domain measurements of the X-ray pulses themselves remain a challenge. Shot-by-shot X-ray diagnostics could enable a new class of simpler and potentially higher-resolution pump-probe experiments. Here, we report training neural networks to combine low-resolution measurements in both the time and frequency domains to recover X-ray pulses at high-resolution. Critically, we also recover the phase, opening the door to coherent-control experiments with XFELs. The model-based generative neural-network architecture can be trained directly on unlabeled experimental data and is fast enough for real-time analysis on the new generation of MHz XFELs.

42 ENGINEERING↗

Design an optimum safety policy for personnel safety management - A system dynamic approach

Personnel safety management (PSM) ensures that employee's work conditions are healthy and safe by various proactive and reactive approaches. Nowadays it is a complex phenomenon because of increasing dynamic nature of organisations which results in an increase of accidents. An important part of accident prevention is to understand the existing system properly and make safety strategies for that system. System dynamics modelling appears to be an appropriate methodology to explore and make strategy for PSM. Many system dynamics models of industrial systems have been built entirely for specific host firms. This thesis illustrates an alternative approach. The generic system dynamics model of Personnel safety management was developed and tested in a host firm. The model was undergone various structural, behavioural and policy tests. The utility and effectiveness of model was further explored through modelling a safety scenario. In order to create effective safety policy under resource constraint, DOE (Design of experiment) was used. DOE uses classic designs, namely, fractional factorials and central composite designs. It used to make second order regression equation which serve as an objective function. That function was optimized under budget constraint and optimum value used for safety policy which shown greatest improvement in overall PSM. The outcome of this research indicates that personnel safety management model has the capability for acting as instruction tool to improve understanding of safety management and also as an aid to policy making.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Modeling microbial dynamics in heterogeneous environments: Growth on soil carbon sources

We have developed a new hybrid model to study how microbial dynamics are affected by the heterogeneity in the physical structure of the environment. The modeling framework can represent porous media such as soil. The individual based biological model can explicitly simulate microbial diversity, and cell metabolism is regulated via optimal allocation of cellular resources to enzyme synthesis, control of growth rate by protein synthesis capacity, and shifts to dormancy. This model was developed to study how microbial community functioning is influenced by local environmental conditions and by the functional attributes of individual microbes. Different strategies for acquisition of carbon from polymeric cellulose were investigated. Bacteria that express membrane-associated hydrolase had different growth and survival dynamics in soil pores than bacteria that release extracellular hydrolases. The kinetic differences may suggest different functional roles for these two classes of microbes in cellulose utilization. Our model predicted an emergent behavior in which co-existence led to higher cellulose utilization efficiency and reduced stochasticity. Microbial community dynamics were simulated at two spatial scales: micro-pores that resemble 6-20 {micro}m size portions of the soil physical structure and in 111 {micro}m size soil aggregates with a random pore structure. Trends in dynamic properties were very similar at these two scales, implying that micro-scale studies can be useful approximations to aggregate scale studies when local effects on microbial dynamics are studied.

54 ENVIRONMENTAL SCIENCES↗

Recursive dynamics for geared robot manipulators

The authors consider the dynamical modeling of robot manipulators whose joint actuators consist of motors driving the joints through gears. The dynamical models for such manipulators are significantly more complex than those for direct drive manipulators. The authors develop recursive O(n) inverse and forward dynamics algorithms as well as recursive O(n2) algorithms for the computation of the mass matrix for geared manipulators. It is shown that, despite the added complexity of the dynamical models for geared manipulators, the algorithms closely resemble the corresponding algorithms for direct drive manipulators, and that the additional algorithmic or computational complexity is relatively insignificant. As a consequence, with little additional cost, existing direct drive algorithms can be easily extended to handle the effects of gearing at the joints.

Jain, A.↗

Incorporating Handling Qualities Analysis into Rotorcraft Conceptual Design

This paper describes the initial development of a framework to incorporate handling qualities analyses into a rotorcraft conceptual design process. In particular, the paper describes how rotorcraft conceptual design level data can be used to generate flight dynamics models for handling qualities analyses. Also, methods are described that couple a basic stability augmentation system to the rotorcraft flight dynamics model to extend analysis to beyond that of the bare airframe. A methodology for calculating the handling qualities characteristics of the flight dynamics models and for comparing the results to ADS-33E criteria is described. Preliminary results from the application of the handling qualities analysis for variations in key rotorcraft design parameters of main rotor radius, blade chord, hub stiffness and flap moment of inertia are shown. Varying relationships, with counteracting trends for different handling qualities criteria and different flight speeds are exhibited, with the action of the control system playing a complex part in the outcomes. Overall, the paper demonstrates how a broad array of technical issues across flight dynamics stability and control, simulation and modeling, control law design and handling qualities testing and evaluation had to be confronted to implement even a moderately comprehensive handling qualities analysis of relatively low fidelity models. A key outstanding issue is to how to 'close the loop' with an overall design process, and options for the exploration of how to feedback handling qualities results to a conceptual design process are proposed for future work.

Analysis into Rotorcraft↗

Using Dynamic Interface Modeling and Simulation to Develop a Launch and Recovery Flight Simulation for a UH-60A Blackhawk

Joint Shipboard Helicopter Integration Process (JSHIP) is a Joint Test and Evaluation (JT&E) program sponsored by the Office of the Secretary of Defense (OSD). Under the JSHDP program is a simulation effort referred to as the Dynamic Interface Modeling and Simulation System (DIMSS). The purpose of DIMSS is to develop and test the processes and mechanisms that facilitate ship-helicopter interface testing via man-in-the-loop ground-based flight simulators. Specifically, the DIMSS charter is to develop an accredited process for using a flight simulator to determine the wind-over-the-deck (WOD) launch and recovery flight envelope for the UH-60A ship/helicopter combination. DIMSS is a collaborative effort between the NASA Ames Research Center and OSD. OSD determines the T&E and warfighter training requirements, provides the programmatics and dynamic interface T&E experience, and conducts ship/aircraft interface tests for validating the simulation. NASA provides the research and development element, simulation facility, and simulation technical experience. This paper will highlight the benefits of the NASA/JSHIP collaboration and detail achievements of the project in terms of modeling and simulation. The Vertical Motion Simulator (VMS) at NASA Ames Research Center offers the capability to simulate a wide range of simulation cueing configurations, which include visual, aural, and body-force cueing devices. The system flexibility enables switching configurations io allow back-to-back evaluation and comparison of different levels of cueing fidelity in determining minimum training requirements. The investigation required development and integration of several major simulation system at the VMS. A new UH-60A BlackHawk interchangeable cab that provides an out-the-window (OTW) field-of-view (FOV) of 220 degrees in azimuth and 70 degrees in elevation was built. Modeling efforts involved integrating Computational Fluid Dynamics (CFD) generated data of an LHA ship airwake and integrating a real-time ship motion model developed based on a batch model from Naval Surface Warfare Center. Engineering development and integration of a three degrees-of-freedom (DOF) dynamic seat to simulate high frequency rotor-dynamics dependent motion cues for use in conjunction with the large motion system was accomplished. The development of an LHA visual model in several different levels of resolution and an aural cueing system in which three separate fidelity levels could be selected were developed. VMS also integrated a PC-based E&S simFUSION system to investigate cost effective IG alternatives. The DIMSS project consists of three phases that follow an approved Validation, Verification and accreditation (VV&A) process. The first phase will support the accreditation of the individual subsystems and models. The second will follow the verification and validation of the integrated subsystems and models, and will address fidelity requirements of the integrated models and subsystems. The third and final phase will allow the verification and validation of the full system integration. This VV&A process will address the utility of the simulated WOD launch and recovery envelope. Simulations supporting the first two stages have been completed and the data is currently being reviewed and analyzed.

Sweeney, Christopher↗

Testing Dynamic Simulation Models for Different Types of Advanced Pumped Storage Hydro Units

A major task of the U.S. Department of Energy (DOE)-sponsored project “Modeling and Analysis of Value of Advanced Pumped Storage Hydropower in the U.S.” was to develop new dynamic simulation models to represent advanced pumped storage hydro (PSH) technologies. This report describes the testing that was performed to demonstrate the performance of these simulation models and illustrates how these models can now be used in analyses required for investigations into applications of these technologies.

Koritarov, Vladimir↗

Space Station - A focus for the development of structural dynamics scale model technology for large flexible space structures

The paper discusses the scale model technology being developed at the NASA Langley Research Center in support of the development of structural dynamic prediction methods for large flexible space structures. Space Station is used as a focus. The Dynamic Scale Model Technology (DSMT) Program is described; results of the effect of scaling Space Station components are presented; and supporting scale model technology development activities are described and results presented. The conceptual design of a hybrid-scale Pathfinder model for developing test techniques and suspension methods is also discussed, and a summary of the broad application of the scale model technology being developed is presented.

Letchworth, Robert↗

System risk quantification and decision making support using functional modeling and dynamic Bayesian network

Risk-informed decision-making requires a probabilistic assessment of the likelihood of success of control action, given the system status. This paper presents a systematic state transition modeling approach integrating dynamic probabilistic risk assessment with a decision-making process using a dynamic Bayesian network (DBN) coupled with functional modeling. A functional model designed with multilevel flow modeling (MFM) technique was used to build a system state structure inferred by energy, mass, and information flow so that one can verify the developed model with respect to system functionality. The MFM model represents the causal relationship among the nodes, which captures the structure of process parameters and control units. Each node may have multiple possible states, and the DBN structured by the MFM model represents the time-domain transitions among the defined states. Furthermore, the MFM-DBN integrated state transition modeling is a white-box approach that allows one to draw the system's risk profile by updating the system states and supports the decisions probabilistically with physical inference. An example of a simple heating system has been used to illustrate this process, including decision-making support based on quantitative risk profile. For demonstrating its applicability to a complex system operational decision making, a case study of station blackout accident scenario leading to the seal loss of coolant accident in a nuclear power plant is presented. The proposed approach effectively provided the risk profile along time for each option so that the operators can make the best decision, which minimizes the plant risk.

42 ENGINEERING↗

Modeling Crabbing Dynamics in an Electron-Ion Collider

A local crabbing scheme requires π/2 (mod π) horizontal betatron phase advances from an interaction point (IP) to the crab cavities on each side of it. However, realistic phase advances generated by sets of quadrupoles, or Final Focusing Blocks (FFB), between the crab cavities located in the expanded beam regions and the IP differ slightly from π/2. To understand the effect of crabbing on the beam dynamics in this case, a simple model of the optics of the Medium Energy Electron-Ion Collider (MEIC) including local crabbing was developed using linear matrices and then studied numerically over multiple turns (1000 passes) of both electron and proton bunches. The same model was applied to both local and global crabbing schemes to determine the linear-order dynamical effects of the synchro-betatron coupling induced by crabbing.

43 PARTICLE ACCELERATORS↗

A Learn-To-Fly Approach for Adaptively Tuning Flight Control Systems

A method is presented for adaptively tuning feedback control gains in a ight control sys- tem to achieve desired closed-loop performance. The method combines efficient parameter estimation for identifying closed-loop dynamics models, with online nonlinear optimization for sequentially perturbing and updating control gains to improve performance. Prior in- formation on stability and control derivatives is not needed, nor is any knowledge about the control system architecture. Following convergence, the optimized control gains (with uncertainties), the open-loop dynamics model, and the closed-loop dynamics model are available. The method is demonstrated for tuning a longitudinal stability augmentation system using a realistic nonlinear ight dynamics simulation of the NASA FASER airplane. Convergence was attained using five piloted maneuvers that spanned approximately one minute of ight test time. Although demonstrated for a relatively simple case, the method is general and can be applied to other aircraft, axes, performance metrics, and control systems.

Grauer, Jared A.↗

Uncertainty analysis of vegetation distribution in the northern high latitudes during the 21st century with a dynamic vegetation model: Uncertainty Analysis of Vegetation Distribution

This study aims to assess how high-latitude vegetation may respond under various climate scenarios during the 21st century with a focus on analyzing model parameters induced uncertainty and how this uncertainty compares to the uncertainty induced by various climates. The analysis was based on a set of 10,000 Monte Carlo ensemble Lund-Potsdam-Jena (LPJ) simulations for the northern high latitudes (45oN and polewards) for the period 1900–2100. The LPJ Dynamic Global Vegetation Model (LPJ-DGVM) was run under contemporary and future climates from four Special Report Emission Scenarios (SRES), A1FI, A2, B1, and B2, based on the Hadley Centre General Circulation Model (GCM), and six climate scenarios, X901M, X902L, X903H, X904M, X905L, and X906H from the Integrated Global System Model (IGSM) at the Massachusetts Institute of Technology (MIT). In the current dynamic vegetation model, some parameters are more important than others in determining the vegetation distribution. Parameters that control plant carbon uptake and light-use efficiency have the predominant influence on the vegetation distribution of both woody and herbaceous plant functional types. The relative importance of different parameters varies temporally and spatially and is influenced by climate inputs. In addition to climate, these parameters play an important role in determining the vegetation distribution in the region. The parameter-based uncertainties contribute most to the total uncertainty. The current warming conditions lead to a complexity of vegetation responses in the region. Temperate trees will be more sensitive to climate variability, compared with boreal forest trees and C3 perennial grasses. This sensitivity would result in a unanimous northward greenness migration due to anomalous warming in the northern high latitudes. Temporally, boreal needleleaved evergreen plants are projected to decline considerably, and a large portion of C3 perennial grass is projected to disappear by the end of the 21st century. In contrast, the area of temperate trees would increase, especially under the most extreme A1FI scenario. As the warming continues, the northward greenness expansion in the Arctic region could continue.

54 ENVIRONMENTAL SCIENCES↗

Launch Vehicle Dynamics Demonstrator Model

The effect of vibration on launch vehicle dynamics was studied. Conditions included three modes of instability. The film includes close up views of the simulator fuel tank with and without stability control.

[Division] Vibration and Dynamics↗

Dynamics and control of a continuum model for a solar power system

An approach for modeling dynamic equations of motion of a plate attached with rigid bodies is presented. The equations of motion are developed using the principle of virtual work. Lagrange multipliers are used as interaction forces and/or moments to maintain prescribed constraints which is the basis of the interconnection between the plate and rigid bodies. The overall approach is unique in the sense that a continuous model described by a family of partial differential equations is established. An approximate formulation by using variational method is established yielding a solution compatible with the assumed degree of approximation. The formulation is useful particularly when parametric study of dynamic response for a satellite power system is desired. As an example, an approximate governing equation of algebraic eigenvalue problem is given for a dual microwave power transmission system. Controller design is discussed.

Juang, J. N.↗

Phase field dislocation dynamics (PFDD) modeling of non-Schmid behavior in BCC metals informed by atomistic simulations

Body-Centered Cubic (BCC) metals exhibit anomalous mechanical properties such as twinning/anti-twinning and tension/compression asymmetry, which are attributed to asymmetric behavior of screw dislocations. Unlike Face-Centered Cubic (FCC) metals, the Critical Resolved Shear Stress (CRSS) of BCC metals deviates from the Schmid law. Here, we use a mesoscale modeling approach called Phase Field Dislocation Dynamics (PFDD) to understand the critical factors that control this non-Schmid behavior and reproduce atomistic predictions of the CRSS (Peierls stress). All inputs to the PFDD model are obtained from Molecular Statics (MS) simulations. Multiple pathways for modeling the non-Schmid behavior are investigated by incorporating the representative dislocation properties into different energy terms in the PFDD model. One way to understand non-Schmid behavior is to incorporate stress components projected on inclined planes into the external energy term within PFDD. Alternatively, we propose that non-Schmid behavior can also be accounted for by considering the variation of the {110} unstable stacking fault energy and the dislocation core width as a function of the applied tensorial stress field. The CRSS predicted using PFDD modeling is in excellent agreement with MS predictions.

36 MATERIALS SCIENCE↗

Model-based Dynamic Control of Speculative Forays in Parallel Computation

In simulations running in parallel, the processors would have to synchronize with other processors to maintain correct global order of computations. This can be done either by blocking computation until correct order is guaranteed, or by \textit{speculatively} proceeding with the best guess (based on local information) and later correcting errors if/as necessary. Since the gainful lengths of speculative forays depend on the dynamics of the application software and hardware at runtime, an online control system is necessary to dynamically choose and/or switch between the blocking and speculative strategies. In this paper, we formulate the reversible speculative computing in large-scale parallel computing as a dynamic linear feedback control (optimization) system model and evaluate its performance in terms of time and cost savings as compared to the traditional (forward) computing. We illustrate with an exact analogy in the form of vehicular travel under dynamic, delayed route information. The objective is to assist in making the optimal decision on what computational approach is to be chosen, by predicting the amount of time and cost savings (or losing) under different environments represented by different parameters and probability distribution functions. We consider the cases of Gaussian, exponential and log-normal distribution functions. The control system is intended for incorporating into speculative parallel applications such as optimistic parallel discrete event simulations to decide at runtime when and to what extent speculative execution can be performed gainfully.

Perumalla, Kalyan↗