Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrically”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Phase transformation, thermal expansion and electrical conductivity of lanthanum chromite

Graphical abstract: - Highlights: • Orthorhombic and rhombohedral phases co-exist at ≥260 °C and cubic above 1000 °C. • Polymorphic changes with temperature in air and Ar–3%H{sub 2} are observed. • Lattice volume change in Ar–3%H{sub 2} atmosphere corresponds to Cr{sup 4+} → Cr{sup 3+} transition. • Change in valence state of Cr{sup 4+} to Cr{sup 3+} results in lower electrical conductivity. • Experimental evidence is provided for poor densification of LaCrO{sub 3} in air. - Abstract: This paper addresses discrepancies pertaining to structural, thermal and electrical properties of lanthanum chromite. Experimental evidence is provided to support the hypothesis for poor densification in air as well as reduction in electrical conductivity in reducing atmosphere. Sintering condition for the synthesis of LaCrO{sub 3} was optimized to 1450 °C and 10 h. Thermo-analytical (differential scanning calorimetry – DSC) and high temperature X-ray diffraction (HT-XRD) studies show that orthorhombic lanthanum chromite transforms into rhombohedral structure at ∼260 °C and cubic structure above 1000 °C. Co-existence of the structural phases and the variation in each polymorph with temperature in both air and 3%H{sub 2}–Ar atmosphere is reported. Presence and absence of Cr-rich phase at inter-particle neck are observed in oxidizing and reducing atmospheres respectively. The linear thermal expansion co-efficient was calculated to be 10.8 ± 0.2 × 10{sup −6} °C{sup −1} in the temperature range of RT–1400 °C. Electrical conductivity of lanthanum chromite was found to be 0.11 S/cm in air. A decrease in electrical conductivity (0.02 S/cm at 800 °C) of LaCrO{sub 3}, as observed in reducing atmosphere (3%H{sub 2}–Ar), corresponds to lattice volume change as indicated by peak shift in HT-XRD results.

36 MATERIALS SCIENCE↗

Synthesis, thermal expansion and high-temperature electrical conductivity of Co-doped (Y,Ca)FeO{sub 3−δ} with orthorhombic perovskite structure

Highlights: • (Y,Ca)(Fe,Co)O{sub 3−δ} was prepared via citrate-based route with annealing at 1150–1200 °C. • Y{sub 0.9}Ca{sub 0.1}Fe{sub 0.8}Co{sub 0.2}O{sub 3−δ} demonstrates low thermal expansion coefficient of 11.9 ppm K{sup −1}. • Oxides do not react with YSZ and GDC up to 1000 °C and 1100 °C, respectively. • Compounds demonstrate higher electrical conductivity in comparison with Y{sub 0.9}Ca{sub 0.1}FeO{sub 3}. • Pr-doped (Y,Ca)(Fe,Co)O{sub 3−δ} demonstrate both higher electrical conductivity and TEC. - Abstract: Orthorhombic perovskites Y{sub 1−x}Ca{sub x}Fe{sub 1−y}Co{sub y}O{sub 3−δ} (0.1 ≤ x ≤ 0.2, 0.1 ≤ y ≤ 0.2 and x = 0.1, y = 0.3) were synthesized in air by the citrate route at 1150–1300 °C. High-temperature X-ray powder diffraction (HT XRPD) data for Y{sub 0.9}Ca{sub 0.1}Fe{sub 0.8}Co{sub 0.2}O{sub 3−δ} at 25–800 °C showed no phase transition with calculated thermal expansion coefficient (TEC) of 11.9 ppm K{sup −1}. High-temperature electrical conductivity measurements revealed almost composition independent conductivity values of 22–27 S/cm at 900 °C. No chemical interaction of Y{sub 0.8}Ca{sub 0.2}Fe{sub 0.9}Co{sub 0.1}O{sub 3−δ} with (Zr,Y)O{sub 2−x} (YSZ) or (Ce,Gd)O{sub 2−x} (GDC) was observed up to 1000 °C and 1100 °C, respectively. Partial replacement of Y by Pr according to formula Y{sub 0.8−z}Pr{sub z}Ca{sub 0.2}Fe{sub 0.7}Co{sub 0.3}O{sub 3−δ}, 0.1 ≤ z ≤ 0.35, leads to an increase of both electrical conductivity up to 50 S/cm (z = 0.3) at 900 °C and dilatometry measured TEC up to 15.1 ppm K{sup −1}. Moderate values of electrical conductivity in combination with low TEC and stability towards chemical interaction with typical SOFC electrolytes make Co-doped Y{sub 1−x}Ca{sub x}FeO{sub 3−δ} promissing cathode materials for intermediate temperature solid oxide fuel cells (IT-SOFC)

36 MATERIALS SCIENCE↗

Structural, electrical and multiferroic properties of La-doped mullite Bi{sub 2}Fe{sub 4}O{sub 9} thin films

Highlights: • Chemical solution deposited La-doped Bi{sub 2}Fe{sub 4}O{sub 9} thin film. • Structural, electrical and multiferroic properties were investigated. • La-doped Bi{sub 2}Fe{sub 4}O{sub 9} exhibited enhanced electrical and multiferroic properties. - Abstract: Thin films of (Bi{sub 2−x}La{sub x})Fe{sub 4}O{sub 9} (x = 0 and x = 0.05) were prepared on Pt(1 1 1)/Ti/SiO{sub 2}/Si(1 0 0) substrates by using a chemical solution deposition method to investigate structural, microstructural, electrical and multiferroic properties. Both the thin films were crystallized in mullite type phases with orthorhombic structures containing no secondary and impurity phases, which was confirmed by X-ray diffraction and Raman spectroscopy studies. The (Bi{sub 1.95}La{sub 0.05})Fe{sub 4}O{sub 9} thin film exhibited improved electrical and multiferroic properties at room-temperature. The leakage current density of the (Bi{sub 1.95}La{sub 0.05})Fe{sub 4}O{sub 9} thin film was one order of magnitude lower than that of the Bi{sub 2}Fe{sub 4}O{sub 9} thin film. Furthermore, in the thin film form, (Bi{sub 2−x}La{sub x})Fe{sub 4}O{sub 9} exhibited better stability against electrical breakdowns and enhanced multiferroic properties.

36 MATERIALS SCIENCE↗

Effects of sulfurization time and H{sub 2}S concentration on electrical properties of Cu{sub 2}ZnSnS{sub 4} films prepared by sol–gel method

Highlights: • Cu{sub 2}ZnSnS{sub 4} (CZTS) films were prepared by sol–gel method following sulfurization. • The sulfurization time and H{sub 2}S concentration have the effects on the electrical properties. • The tin loss is increased with the increasing of the sulfurization time. • The secondary phases like ZnS make the electrical properties worse. • The CZTS films sulfurized at 5% H{sub 2}S for 90 min had the best electrical properties. - Abstract: Cu{sub 2}ZnSnS{sub 4} (CZTS) thin films have been successfully deposited by a sol–gel method and sulfurization process. The properties of the films were investigated by varying sulfurization time and H{sub 2}S concentration. X-ray diffraction and Raman spectra analyses revealed the formation of CZTS films with a tetragonal type kesterite structure. With increasing the sulfurization time and H{sub 2}S concentration, the intensity of the kesterite (1 1 2) peak became sharper. The stoichiometric ratios of the CZTS films were different from the precursors, which was due to Sn loss during the sulfurization process. The electrical resistivity and mobility of the films increased while the carrier concentration decreased with increasing the sulfurization time. The CZTS thin films sulfurized at 5% H{sub 2}S concentration for 90 min had the best opto-electrical properties with E{sub g} of 1.41 eV, resistivity of 3.64 Ω cm, carrier concentration of 1.11 × 10{sup 18} cm{sup −3} and mobility of 1.54 cm{sup 2}/(V s) at room temperature for PV application.

36 MATERIALS SCIENCE↗

Charging needs for electric semi-trailer trucks

Battery-electric vehicles provide a pathway to decarbonize heavy-duty trucking, but the market for heavy-duty battery-electric semi-trailer trucks is nascent, and specific charging requirements remain uncertain. We leverage large-scale vehicle telematics data (>205 million miles of driving) to estimate the charging behaviors and infrastructure requirements for U.S. battery-electric semi-trailer trucks within three operating segments: local, regional, and long-haul. We model two types of charging - mid-shift (fast) and off-shift (slow) - and show that off-shift charging at speeds compatible with current light-duty charging infrastructure (i.e., =350 kW) can supply 35% to 77% of total energy demand for local and regional trucks with =300-mile range. Megawatt-level speeds are required for mid-shift charging, which make up 44% to 57% of energy demand for long-haul trucks with =500-mile range. However, demand shifts from mid-shift to off-shift charging as the range for battery-electric trucks increases and when off-shift charging is widely available. Finally, we observe geographic trends in charging demand, finding that local trucks have greater demand within urban areas, whereas long-haul trucks have more demand along rural interstate corridors. As the range for battery-electric trucks increases, we show that charging demand shifts from rural to urban locations due to observed vehicle dwell tendencies.

33 ADVANCED PROPULSION SYSTEMS↗

Operational optimization for multi-functional charging station with electric and hydrogen-powered vehicles

The rapid adoption of electric vehicles (EVs) and hydrogen fuel cell vehicles (HFCVs), combined with global efforts to reduce carbon emissions, has accelerated the development of EV charging and hydrogen refueling stations. In response to this demand, this paper introduces the concept of Multi-Functional Charging Station (MFCS) that integrates power generation, EV charging, battery swapping, and hydrogen refueling. A comprehensive operational model is developed for the MFCS that couples electricity and hydrogen conversion and storage technologies to enhance infrastructure utilization and improve overall system efficiency. The model also considers multiple revenue streams, including participation in energy and ancillary markets. To validate the effectiveness of the proposed model and evaluate its performance, a series of numerical experiments are conducted with different charger numbers, different electricity purchase limits, and different charger allocations. Numerical results demonstrate that shared charger configurations can lead to 8.11 % improvement in operational profit by improving resource utilization and reducing the number of depleted batteries at the end of operations compared to allocated charger setups. By varying the number of chargers, sensitivity analysis identifies diminishing marginal returns beyond about 45 chargers, suggesting it as an optimal sizing point under current settings. The integration of electricity and hydrogen conversion is also explored under scenarios with limited external electricity purchases. In conclusion, these findings indicate that optimizing charger allocation and energy management can significantly enhance station productivity and profitability, ultimately supporting the broader adoption of electrified and hydrogen-based transportation solutions.

Charging station↗

Refueling infrastructure planning in intercity networks considering route choice and travel time delay for mixed fleet of electric and conventional vehicles

The range anxiety has been a major factor that affects the market acceptance of electric vehicles. Even with the recent development of battery technologies, a lack of charging stations and range anxiety are still significant concerns, specifically for intercity trips. This calls for more investments in building charging stations and advancing battery technologies to increase the market share of electric vehicles and improve sustainability. This study suggests a configuration for plug-in electric vehicle charging infrastructure to support long-distance intercity trips of electric vehicles at the network level. A model is proposed to minimize the total system cost including infrastructure investment (building charging stations/spots) and travel time delays (charging time, waiting time in the queue, and detour time to access charging stations). This study fills existing gaps in the literature by capturing realistic patterns of travel demand and considering flow-dependent charging delays at charging stations. Furthermore, the proposed model, which is formulated as a mixed-integer program with nonlinear constraints, solves the optimization problem at the network level. At the network level, impacts of charging station locations on the traffic assignment problem with a mixed fleet of electric and conventional vehicles need to be considered. To this end, a traffic assignment module is integrated with a simulated annealing algorithm. The numerical experiments show a satisfactory application of the model for a full-scale case study (intercity network in Michigan). The solution quality and efficiency of the proposed solution algorithm are evaluated against those of an enumeration approach for a small case study. The results suggest that even for the current market share and charging stations’ setting, a significant investment is needed to support intercity trips without range anxiety issues and with acceptable delays. Additionally, through sensitivity analyses, the required infrastructure and battery investments to support intercity trips with acceptable delays are established for hypothetical increased market shares and battery size in the future.

42 ENGINEERING↗

Joint routing of conventional and range-extended electric vehicles in a large metropolitan network

Range-extended electric vehicles combine the higher efficiency and environmental benefits of battery-powered electric motors with the longer mileage and autonomy of conventional internal combustion engines. This combination is particularly advantageous for time-constrained delivery routing in dense urban areas, where battery recharging along routes can be too time-consuming to economically justify the use of all-electric vehicles. However, switching from electric to conventional fossil fuel modes also results in higher costs and emissions and lower efficiency. This paper analyzes this heterogeneous vehicle routing problem and describes two solution methods: an exact branch-price-and-cut algorithm and an iterated tabu search metaheuristic. From a methodological perspective, we find that the exact algorithm consistently obtains tight lower bounds that also serve to certify the metaheuristic solutions as near-optimal. From a policy standpoint, we examine a large-scale real-world case study concerning parcel deliveries in the Chicago metropolitan area and quantify various operational metrics including energy costs and vehicle miles traveled. We find that by deploying roughly 20% of range -extended vehicles with a modest all-electric range of 33 miles, parcel distributors can save energy costs by up to 17% while incurring less than 0.5% increase in vehicle miles traveled. Increasing the range to 60 miles further reduces costs by only 4%, which can alternatively be achieved by decreasing the average service time by 1 minute or increasing driver working time by 1 hour. In conclusion, our study reveals several key areas of improvement on which vehicle manufacturers, distributors, and policy makers can focus their attention.

33 ADVANCED PROPULSION SYSTEMS↗

The impact of tribology on energy use and CO 2 emission globally and in combustion engine and electric cars

Growing concerns over energy and environmental sustainability have lately sparked worldwide interest in more efficient and cleaner transportation systems and industrial activities. Friction roughly consumes one-fifth of all energy used worldwide. One-third of all energy used in transportation goes to overcome friction. At the same time, the fruits of decades of dedicated research on all-electric vehicles powered by advanced batteries are paving the way toward a much cleaner and sustainable transportation future. In this article, we provide a short overview of what are the energy efficiency and environmental impacts of current transportation, industrial, and residential systems and how much of that efficiency is adversely affected by friction and wear losses in moving mechanical parts and components. We also touch upon recent advances in new materials, lubricants, and design changes that could reduce energy losses by 18–40%, mainly resulting from friction and wear. The savings would be up to 8.7% of the total global energy use and 1.4% of the gross national products (GNP). Finally, we calculate the energy consumption and friction losses in battery-powered electric passenger cars and show the benefit of electric cars where the total energy use is in average 3.4 times lower compared to combustion engine powered cars. The CO 2 emissions are 4.5 times higher for a combustion engine car compared to an electric car when the electricity comes from renewable energy sources. Moving from fossil to renewable energy sources may cut down the energy losses due to friction in energy production by more than 60%.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Consumer behaviour and environmental education in the field of waste electrical and electronic toys: A Spanish case study

Highlights: • Consumption/disposal habits of waste electrical and electronic toys. • Environmental education as a key factor to improve WEEE management. • Three environmental education actions to increase the collection of waste toys. - Abstract: This paper reports on a project focused on obtaining the current consumption and disposal habits of electrical and electronic toys from a survey aimed at parents of children of nine pre- and primary schools. In addition, it is also focused on identifying the most effective way of transmitting environmental information to parents and children to promote the collection of electrical and electronic toys at their end-of-life. The study was implemented in a Spanish municipality. With regard to the consumption habits, aspects related to the amount of toys that children receive annually and percentage of those which are electrical and electronic toys have been obtained and classified according to the family size. Results from Chi-squared analysis and Ordinal Logistic Regression show that there is a statistically significance relationship among these variables. Regarding disposal habits, aspects related to the reasons and way for discarding electrical and electronic toys, time that toys are kept at home or the willingness to rent or buy second hand e-toys have been obtained. What really attracts attention is that, apart from consumers who donate the toy to family or social associations, 67.1% of consumers discard them along with other waste fractions in domestic bins, whereas only 32.9% do so at recycling points, as Directive 2012/19/EU requires. To increase this percentage, three environmental education actions (distinguishing from each other by the way used to transmit the environmental information: paper, audiovisual or personal communication) have been designed, applied and evaluated their efficiency according to the amount of waste toys collected.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

pyEF: A Python Framework for QM and QM/MM Atom-Wise Electric Field Analysis

We introduce pyEF, a software package for computing molecular electric fields, electrostatic interaction energies, and electrostatic potentials from quantum mechanical (QM) atom-centered multipole expansions with atom-wise decomposable contributions. We demonstrate the computational efficiency and accuracy of this QM-derived electric field evaluation tool through several tests. To assess the influence of the underlying QM method and charge partitioning scheme on these electrostatic quantities, we analyze over 250 configurations of an acetone solute molecule in five solvents of variable polarity. We find that electric field calculations are highly sensitive to the choice of charge partitioning method. Even among real-space charge schemes, acetone Stark tuning rates differ by up to a factor of 2. Benchmarking computed solvent dipole moments against experimental bulk values, we conclude that the CM5, ADCH, and Hirshfeld-I charge schemes most reliably capture solvent electrostatics and therefore provide a more faithful foundation for computing electric fields. When constructed from these real-space charges, electric fields are nearly insensitive to basis set size and monotonically increase in magnitude with higher Fock exchange. We also demonstrate efficient convergence of QM electrostatics when more distant molecules are represented solely by MM point charges, reducing computational overhead. Leveraging these findings, we demonstrate the use of pyEF to deduce environmental effects on a transition metal complex from a Ga 4 L 6 12– nanocage and quantify the dominant role of organic linkers in orchestrating electrostatic preorganization.

electric fields↗

Pulsed Electrical Stimulation Enhances Body Fluid Transport for Collagen Biomineralization

Mechanical loads from physiologic activities such as walking and running generate bioelectricity in bones. By mimicking bioelectricity, external electrical stimulations have also been used therapeutically to stimulate bone-forming cells and, thus, to promote bone regeneration. However, little is known about the physicochemical mechanism(s) by which electrical stimulations drives calcium phosphate mineralization of collagen. Here, we showed that, during in vitro collagen mineralization in the absence of cells, application of pulsed electrical stimulation significantly enhanced the transport of ionic body fluid components through a micrometer-scale channel (~100–200 μm gap space between the inner surfaces of tube-like collagen scaffolds and a cathode placed inside the collagen scaffolds). The enhanced transport of ionic precursors increased diffusion of the charged precursors from the channel to the inner collagen surface, where bone mineralization was otherwise restricted. The results indicate that pulsed electrical signals can locally accelerate the nucleation of calcium phosphate nanocrystals in or on collagen, allowing us to better control the spatial distribution of the nanocrystals at the microscale. Finally, the findings from this study provide insights into the utilization of electrical stimulation for applications such as facilitating bone-fracture healing and designing better bone-specific biomaterials.

59 BASIC BIOLOGICAL SCIENCES↗

Fabrication and Performance Evaluation of Double-Sided Copper Nanowire Arrays as Thermal and Electrical Interfacial Layers

Reducing contact interface thermal and electrical resistances is in great demand across various industries, particularly in the semiconductor industry. This study introduces an approach using double-sided copper nanowire (Cu NW) arrays on copper sheets as both thermal and electrical interfacial layers, designed to effectively accommodate the topographical inconsistencies between contact surfaces. Further, experimental outcomes reveal a significant reduction in thermal contact resistance (TCR), with a value of 2.5 mm 2 K W –1 , thereby exceeding the efficiency of reported nanostructural thermal interface materials (TIMs). Additionally, when utilized as an electrical interfacial layer, these double-sided Cu NWs arrays dramatically reduced electrical contact resistance (ECR), outperforming traditional conductive grease in applications necessitating separable bonding, though showing comparable performance to costly silver-based conductive epoxies required for permanent, inseparable bonds. The promising results of the double-sided Cu NWs arrays in reducing both TCR and ECR, confirmed by finite element simulation, highlight their substantial potential in advancing TIMs and electrical interconnection applications across various sectors.

42 ENGINEERING↗

Measuring Local Electric Fields and Local Charge Densities at Electrode Surfaces Using Graphene-Enhanced Raman Spectroscopy (GERS)-Based Stark-Shifts

Here, we report spectroscopic measurements of the local electric fields and local charge densities at electrode surfaces using graphene-enhanced Raman spectroscopy (GERS) based on the Stark-shifts of surface-bound molecules and the G band frequency shift in graphene. Here, monolayer graphene is used as the working electrode in a three-terminal potentiostat while Raman spectra are collected in situ under applied electrochemical potentials using a water immersion lens. First, a thin layer (1 Å) of copper(II) phthalocyanine (CuPc) molecules are deposited on monolayer graphene by thermal evaporation. GERS spectra are then taken in an aqueous solution as a function of the applied electrochemical potential. The shifts in vibrational frequencies of the graphene G band and CuPc are obtained simultaneously and correlated. The upshifts in the G band Raman mode are used to determine the free carrier density in the graphene sheet under these applied potentials. Of the three dominant peaks in the Raman spectra of CuPc (i.e., 1531, 1450, and 1340 cm –1 ), only the 1531 cm –1 peak exhibits Stark-shifts and can, thus, be used to report the local electric field strength at the electrode surface under electrochemical working conditions. Between applied electrochemical potentials from -0.8 V to 0.8 V vs NHE, the free carrier density in the graphene electrode spans a range from -4 × 10 12 cm –2 to 2 × 10 12 cm –2 . Corresponding Stark-shifts in the CuPc peak around 1531 cm –1 are observed up to 1.0 cm –1 over a range of electric field strengths between -3.78 × 10 6 and 1.85 × 10 6 V/cm. Slightly larger Stark-shifts are observed in a 1 M KCl solution, compared to those observed in DI water, as expected based on the higher ion concentration of the electrolyte. Based on our data, we determine the Stark shift tuning rate to be 0.178 cm –1 / (10 6 V/cm), which is relatively small due to the planar nature of the CuPc molecule, which largely lies perpendicular to the electric field at this electrode surface. Computational simulations using density functional theory (DFT) predict similar Stark shifts and provide a detailed atomistic picture of the electric field-induced perturbations to the surface-bound CuPc molecules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrical Conductivity and Sound Velocities of Talc Under High Pressure and High Temperature Conditions and Application to the Subducting Cocos Plate

Talc is expected to be an important water carrier in Earth's upper mantle, and understanding its electrical and seismic properties under high pressure and temperature conditions is required to detect possible talc-rich regions in subduction zones imaged using geophysical observations. Here, we conducted acoustic and electrical experiments on natural talc aggregates at relevant pressure-temperature conditions. Compressional wave velocity (V p ) was measured using ultrasonic interferometry in a Paris-Edinburgh press at pressures up to 3.4 GPa and temperatures up to 873 K. Similar Vp values are obtained regardless of the initial crystallographic preferred orientation of the samples, which can be explained by talc grain reorientation during the experiment, with the (001) plane becoming perpendicular to the uniaxial compression axis. Electrical conductivity of the same starting material was determined using impedance spectroscopy in a multi-anvil press up to 6 GPa and 1263 K. Two conductivity jumps are observed, at ∼860–1025 K and ∼940–1080 K, depending on pressure, and interpreted as talc dehydroxylation and decomposition, respectively. Electrical anisotropy is observed at low temperature and decreases with increasing pressure (∼10 at 1.5 GPa and ∼2 at 3.5 GPa). Comparison of acoustic and electrical results with geophysical observations in central Mexico supports the presence of a talc-bearing layer atop the subducted Cocos plate.

Cocos plate↗

Bounding the costs of electric vehicle managed charging—supply curves for scenarios from 2025 to 2050

As electric vehicle (EV) adoption increases, the resulting EV battery charging will increase demand on the electric power grid. Through EV managed charging (EVMC) programs, charging can be shifted in time to support electric grid reliability and reduce electricity costs. EVMC can offer an alternative to additional supply-side generation, but the costs of EVMC implementation must be understood to evaluate the cost-benefits of EVMC. This paper presents bottom-up, forward-looking (from 2025 through 2050) estimates of the incremental costs associated with different EVMC dispatch mechanisms available to electric utilities. The costs of enabling EVMC for a range of customer participation levels are presented in the form of supply curves, which provide per-EV costs for a targeted level of participation. The largest drivers of cost variation are assumptions about future charging flexibility paradigms described in four scenarios. These supply curves can be used to quantify the expected costs of EVMC programs and enable comparison with supply-side or other demand flexibility alternatives.

25 ENERGY STORAGE↗

Combined effect of Debye plasma environment and external electric field on hydrogen atom

We consider weakly coupled plasmas, characterized by Debye-Huckel model potential, and an external electric field along z-axis. Due to plasma environment the energy levels of atom are shifted up, bound states are merged to continuum. For external electric field the excited energy levels also split up; degenerate energy eigenvalues become nondegenerate. In the presence of external electric field, energy levels are shifted up and down, except ground state. The ground state energy value is shifted only down. Therefore, it is very interesting to study the combined effect of plasmas and external electric field on a simple atom (hydrogen). To calculate the energy levels and the corresponding states, we expand the wave function in terms of linear combination of the basis functions. The basis is generated by hydrogenic wave functions. Here, we estimate various plasma surroundings and electric field strengths. We observe converged results for the basis size 45, with angular momentum states up to eight.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Optical emission from a small scale model electric arc furnace in 250-600 nm region

Optical emission spectroscopy has been for long proposed for monitoring and studying industrial steel making processes. Whereas the radiative decay of thermal excitations is always taking place in high temperatures needed in steel production, one of the most promising environment for such studies are electric arc furnaces, creating plasma in excited electronic states that relax with intense characteristic emission in the optical regime. Unfortunately, large industrial scale electric arc furnaces also present a challenging environment for optical emission studies and application of the method is not straightforward. To study the usability of optical emission spectroscopy in real electric arc furnaces, we have developed a laboratory scale DC electric arc furnace presented in this paper. With the setup, optical emission spectra of Fe, Cr, Cr{sub 2}O{sub 3}, Ni, SiO{sub 2}, Al{sub 2}O{sub 3}, CaO, and MgO were recorded in the wavelength range 250-600 nm and the results were analyzed with the help of reference data. The work demonstrates that using characteristic optical emission, obtaining in situ chemical information from oscillating plasma of electric arc furnaces is indeed possible. In spite of complications, the method could possibly be applied to industrial scale steel making process in order to improve its efficiency.

36 MATERIALS SCIENCE↗