Search NASA⌕ Search

SEARCH · Search NASA

Results for “flow improvers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

On the modelling of scalar and mass transport in combustor flows

Results are presented of a numerical study of swirling and nonswirling combustor flows with and without density variations. Constant-density arguments are used to justify closure assumptions invoked for the transport equations for turbulent momentum and scalar fluxes, which are written in terms of density-weighted variables. Comparisons are carried out with measurements obtained from three different axisymmetric model combustor experiments covering recirculating flow, swirling flow, and variable-density swirling flow inside the model combustors. Results show that the Reynolds stress/flux models do a credible job of predicting constant-density swirling and nonswirling combustor flows with passive scalar transport. However, their improvements over algebraic stress/flux models are marginal. The extension of the constant-density models to variable-density flow calculations shows that the models are equally valid for such flows.

Nikjooy, M.↗

Large Eddy/Reynolds-Averaged Navier-Stokes Simulations of CUBRC Base Heating Experiments

ven with great advances in computational techniques and computing power during recent decades, the modeling of unsteady separated flows, such as those encountered in the wake of a re-entry vehicle, continues to be one of the most challenging problems in CFD. Of most interest to the aerothermodynamics community is accurately predicting transient heating loads on the base of a blunt body, which would result in reduced uncertainties and safety margins when designing a re-entry vehicle. However, the prediction of heat transfer can vary widely depending on the turbulence model employed. Therefore, selecting a turbulence model which realistically captures as much of the flow physics as possible will result in improved results. Reynolds Averaged Navier Stokes (RANS) models have become increasingly popular due to their good performance with attached flows, and the relatively quick turnaround time to obtain results. However, RANS methods cannot accurately simulate unsteady separated wake flows, and running direct numerical simulation (DNS) on such complex flows is currently too computationally expensive. Large Eddy Simulation (LES) techniques allow for the computation of the large eddies, which contain most of the Reynolds stress, while modeling the smaller (subgrid) eddies. This results in models which are more computationally expensive than RANS methods, but not as prohibitive as DNS. By complimenting an LES approach with a RANS model, a hybrid LES/RANS method resolves the larger turbulent scales away from surfaces with LES, and switches to a RANS model inside boundary layers. As pointed out by Bertin et al., this type of hybrid approach has shown a lot of promise for predicting turbulent flows, but work is needed to verify that these models work well in hypersonic flows. The very limited amounts of flight and experimental data available presents an additional challenge for researchers. Recently, a joint study by NASA and CUBRC has focused on collecting heat transfer data on the backshell of a scaled model of the Orion Multi-Purpose Crew Vehicle (MPCV). Heat augmentation effects due to the presence of cavities and RCS jet firings were also investigated. The high quality data produced by this effort presents a new set of data which can be used to assess the performance of CFD methods. In this work, a hybrid LES/RANS model developed at North Carolina State University (NCSU) is used to simulate several runs from these experiments, and evaluate the performance of high fidelity methods as compared to more typical RANS models. .

Salazar, Giovanni↗

Development of a general method for obtaining the geometry of microfluidic networks

In the present study, a general method for geometry of fluidic networks is developed with emphasis on pressure-driven flows in the microfluidic applications. The design method is based on general features of network's geometry such as cross-sectional area and length of channels. Also, the method is applicable to various cross-sectional shapes such as circular, rectangular, triangular, and trapezoidal cross sections. Using constructal theory, the flow resistance, energy loss and performance of the network are optimized. Also, by this method, practical design strategies for the fabrication of microfluidic networks can be improved. The design method enables rapid prediction of fluid flow in the complex network of channels and is very useful for improving proper miniaturization and integration of microfluidic networks. Minimization of flow resistance of the network of channels leads to universal constants for consecutive cross-sectional areas and lengths. For a Y-shaped network, the optimal ratios of consecutive cross-section areas (A{sub i+1}/A{sub i}) and lengths (L{sub i+1}/L{sub i}) are obtained as A{sub i+1}/A{sub i} = 2{sup −2/3} and L{sub i+1}/L{sub i} = 2{sup −1/3}, respectively. It is shown that energy loss in the network is proportional to the volume of network. It is also seen when the number of channels is increased both the hydraulic resistance and the volume occupied by the network are increased in a similar manner. Furthermore, the method offers that fabrication of multi-depth and multi-width microchannels should be considered as an integral part of designing procedures. Finally, numerical simulations for the fluid flow in the network have been performed and results show very good agreement with analytic results.

36 MATERIALS SCIENCE↗

Unsteady three-dimensional Navier-Stokes simulations of turbine rotor-stator interaction

Fluid flows within turbomachinery tend to be extremely complex. Understanding such flows is crucial to efforts to improve current turbomachinery designs, and the computational approach can be used to great advantage in this regard. This study presents a finite-difference, unsteady, thin-layer Navier-Stokes approach to calculating the flow within an axial turbine stage. The relative motion between the stator and rotor airfoils is made possible with the use of patched grids that move relative to each other. The calculation includes end-wall and tip-leakage effects. Results in the form of time-averaged surface pressures, pressure amplitudes (corresponding to the pressure fluctuation in time), near-surface velocity vectors, and pressure contours in the passage areas are presented. The numerical results are compared with experimental data wherever possible, and the agreement between the two is found to be good.

Rai, Man Mohan↗

Method and system to maintain electrolyte stability for all-iron redox flow batteries

Methods and systems are provided which maintain the positive and negative electrolyte pH and stability of a redox flow battery through the use of electrochemical rebalancing cells. The electrochemical cells may be activated by applying an electrical load to affect changes to the pH of the electrolytes. The use of the electrochemical cells improves long term performance stability redox flow batteries by decreasing and/or eliminating Fe(OH)3 precipitation formation.

25 ENERGY STORAGE↗

Method and system to maintain electrolyte stability for all-iron redox flow batteries

Methods and systems are provided which maintain the positive and negative electrolyte pH and stability of a redox flow battery through the use of electrochemical rebalancing cells. The electrochemical cells may be activated by applying an electrical load to affect changes to the pH of the electrolytes. The use of the electrochemical cells improves long term performance stability redox flow batteries by decreasing and/or eliminating Fe(OH)3 precipitation formation.

25 ENERGY STORAGE↗

Solving the Hele–Shaw flow using the Harrow–Hassidim–Lloyd algorithm on superconducting devices: A study of efficiency and challenges

The development of quantum processors for practical fluid flow problems is a promising yet distant goal. Recent advances in quantum linear solvers have highlighted their potential for classical fluid dynamics. In this study, we evaluate the Harrow–Hassidim–Lloyd (HHL) quantum linear systems algorithm (QLSA) for solving the idealized Hele–Shaw flow. Our focus is on the accuracy and computational cost of the HHL solver, which we find to be sensitive to the condition number, scaling exponentially with problem size. This emphasizes the need for preconditioning to enhance the practical use of QLSAs in fluid flow applications. Moreover, we perform shots-based simulations on quantum simulators and test the HHL solver on superconducting quantum devices, where noise, large circuit depths, and gate errors limit performance. Error suppression and mitigation techniques improve accuracy, suggesting that such fluid flow problems can benchmark noise mitigation efforts. Finally, our findings provide a foundation for future, more complex application of QLSAs in fluid flow simulations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Simulation of Channel Flow with Square Ribs for Blanket First-Wall Cooling: Geometry-Specific Tuning of k-ω Model Using Adjoint Method

Cooling of the plasma-facing first wall is challenging in the design of blanket components because of the high heat flux (on the order of 𝑀𝑊/𝑚2) from the plasma, especially when a low thermal mass medium like helium is chosen as the coolant. Therefore, heat transfer enhancement in which the convective heat transfer rate is augmented by the addition of turbulence-promoting structures becomes a key initiative for providing sufficient cooling capability with helium. Previously, computational fluid dynamics simulations had been performed on pipe flows with different transverse and longitudinal ribbed geometries at Oak Ridge National Laboratory to compare the enhancement performance among different ribbed geometries. Rib shape morphing had been conducted to obtain an optimized rib profile. In the work presented here, the adjoint method is adopted in the ANSYS Fluent solver for turbulence model augmentation, and the Generalized k-ω (GEKO) turbulence model is employed because of its ability of tuning the turbulence model. The Nusselt number and pressure drop obtained from the channel flow with bottom ribbed wall experiments are used as the targets. Sensitivity analysis provides information as guidance to improve the turbulence model accuracy. The augmented GEKO model is tuned for the studied ribbed channel geometry and flow conditions, providing improved predictive accuracy within this context. Extension to other configurations offers potential but may require additional tuning and validation.

Xu, Tracy [ORNL] (ORCID:0009000193700887)↗

Modeling the temporal dynamics of nonstructural carbohydrate pools in forest trees

Trees store carbohydrates, in the form of sugars and starch, as reserves to be used to power both future growth as well as to support day-to-day metabolic functions. These reserves are particularly important in the context of how trees cope with disturbance and stress—for example, as related to pest outbreaks, wind or ice damage, and extreme climate events. In this project, we measured the size of carbon reserves in forest trees, and determined how quickly these reserves are used and replaced—i.e., their “turnover time”. Our work was conducted at Harvard Forest, a temperate deciduous forest in central Massachusetts. Through field sampling, laboratory-based chemical analyses, and allometric modeling, we scaled these measurements up to whole-tree NSC budgets. We used these data to test and improve computer simulation models of carbon flow through forest ecosystems. Our modeling focused on the mathematical representation of these stored carbon reserves, and we examined the sensitivity of model performance to different model structures. This project contributes to DOE’s goal to improve next-generation models of the earth system, and to understand the impacts of climate change on terrestrial ecosystems.

59 BASIC BIOLOGICAL SCIENCES↗

Efficiency of an AMTEC recirculating test cell, experiments and projections

The alkali metal thermal to electric converter (AMTEC) is an electrochemical device for the direct conversion of heat to electrical energy with efficiencies potentially near Carnot. The future usefulness of AMTEC for space power conversion depends on the efficiency of the devices. Systems studies have projected from 15 to 35 percent thermal to electric conversion efficiencies, and one experiment has demonstrated 19 percent efficiency for a short period of time. Recent experiments in a recirculating test cell (RTC) have demonstrated sustained conversion efficiencies as high as 10.2 percent early in cell life and 9.7 percent after maturity. Extensive thermal and electrochemical analysis of the cell during several experiments demonstrated that the efficiency could be improved in two ways. First, the electrode performance could be improved. The electrode for these tests operated at about one third the power density of state of the art electrodes. The low power density was caused by a combination of high series resistance and high mass flow resistance. Reducing these resistances could improve the efficiency to greater than 10 percent. Second, the cell thermal performance could be improved. Efficiencies greater than 14 percent could be realized through reducing the radiative thermal loss. Further improvements to the efficiency range predicted by systems studies can be accomplished through the development and use of an advanced condenser with improved reflectivity, close to that of a smooth sodium film, and the series connecting of individual cells to further reduce thermal losses.

Underwood, M. L.↗

Sensorimotor Adaptability Training Improves Motor and Dual-Task Performance

The overall objective of our project is to develop a sensorimotor adaptability (SA) training program designed to facilitate recovery of functional capabilities when astronauts transition to different gravitational environments. The goal of our current study was to determine if SA training using variation in visual flow and support surface motion produces improved performance in a novel sensory environment and demonstrate the retention characteristics of SA training.

Bloomberg, J.J.↗

Space Propulsion Design and Analysis

This software provides an improved methodology for predicting launcher base pressure and heat loads for RSRM (Reusable Solid Rocket Motor) launchers by accounting for complex anisotropic stress/strains and variable turbulent Prandtl and Schmidt numbers. A "building block" approach to turbulence model development, and validation has been applied for improved missile/launcher base region analysis. Modifications to existing kappa - epsilon turbulence models and application of scalar variance models are incorporated into a RANS-based method for aeropropulsive flow modeling, directly related to base flow methodology. (RANS stands for Reynolds-averaged Navier-Stokes.) The models are applied in a RANS solver framework and can improve analysis of other complex flow fields. The enhanced models provide a more accurate predictive capability for improving the design and analysis of RSRM launcher configuration. The kappa - epsilon model enhancements have been shown to improve the capability for predicting turbulence effects in base blow environments. The scalar variance models have been assessed over a wide range of flow configurations to improve prediction of turbulent scalar mixing.

Sinha, Neeraj↗

Improvements to an Explicit Algebraic Stress Model for Turbulent Jet Mixing Predictions

Modifications to key coefficients in a k − E based explicit algebraic stress model (EASM) are examined with the objective of improving the prediction of turbulent jet flows. The pressure strain coefficient, C2 and the turbulent diffusion coefficients, σk and σE were investigated. For a series of benchmark subsonic jets at heated and unheated conditions, lowering C2 from the default value of 0.36 to 0.10 resulted in a significant improvement in the jet mixing, when compared to experimental data. Changing σk and σE from default values of 1.00 and 1.4489, respectively, to 0.50 and 0.7244, respectively, improved the initial mixing rate, while reducing the farfield mixing rate and the peak turbulent kinetic energy along the centerline. A high-speed mixing layer was also investigated for performance of baseline and modified EASM coefficients, with similar results as for the jet cases. A flat plate boundary layer was briefly examined to determine the effects of changing the coefficients on the turbulent skin friction coefficient. The change to the pressure strain coefficient, C2 = 0.10 is recommended for future EASM calculation of jets flow; however, it is also recommended that the diffusion coefficients remain at their default values.

Turbulent Mixing↗

Predicting the potentials, solubilities and stabilities of metal-acetylacetonates for non-aqueous redox flow batteries using density functional theory calculations

New active materials are needed to improve the performance and reduce the cost of non-aqueous redox flow batteries (RFBs) for grid-scale energy storage applications. Efforts to develop better performing materials, which have largely been empirical, would benefit from a better understanding of relationships between structural, electronic and RFB-relevant functional properties. This paper focuses on metal-acetylacetonates, a class of metal coordination complexes that has shown promise for use in RFBs, and describes correlations between their experimentally measured standard potentials, solubilities, and stabilities (cycle lifes), and selected chemical, structural and electronic properties determined from Density Functional Theory (DFT) calculations. The training set consisted of 16 complexes including 5 different metals and 11 different substituents on the acetylacetonate ligand. Standard potentials for those compounds were calculated and are in good agreement with experimentally measured results. A predictive equation based on the solvation energies and dipole moments, two easily computed properties, reasonably modeled the experimentally determined solubilities. Importantly, we were able to identify a descriptor for the stability of acetylacetonates. The experimentally determined stability, quantified as the cycle life to a given degree of degradation, correlated with the percentage of the highest occupied (HOMO) or lowest unoccupied molecular orbital (LUMO) on the metal of the complex. This percentage is influenced by the degree of ligand innocence (irreducibility), and complexes with the most innocent ligands yielded the most stable redox reactions. To this end, VO(acetylacetonate)(2) and Fe(acetylacetonate)(3), with nearly 80% of the HOMO and LUMO on the metal, possessed the most stable oxidation and reduction half-reactions, respectively. The structure-function relationships and correlations presented in this paper could be used to predict new, highly soluble and stable complexes for RFB applications.

Kucharyson, J. F.↗

Evaluation of Turbulence Models for Unsteady Flows of an Oscillating Airfoil

Unsteady flowfields of a two-dimensional oscillating airfoil are calculated using an implicit, finite-difference, Navier Stokes numerical scheme. Five widely used turbulence models are used with the numerical scheme to assess the accuracy and suitability of the models for simulating the retreating blade stall of helicopter rotor in forward flight. Three unsteady flow conditions corresponding to an essentially attached flow, light-stall, and deep-stall cases of an oscillating NACA 0015 wing experiment were chosen as test cases for computations. Results of unsteady airloads hysteresis curves, harmonics of unsteady pressures, and instantaneous flowfield patterns are presented. Some effects of grid density, time-step size, and numerical dissipation on the unsteady solutions relevant to the evaluation of turbulence models are examined. Comparison of unsteady airloads with experimental data show that all models tested are deficient in some sense and no single model predicts airloads consistently and in agreement with experiment for the three flow regimes. The chief findings are that the simple algebraic model based on the renormalization group theory (RNG) offers some improvement over the Baldwin Lomax model in all flow regimes with nearly same computational cost. The one-equation models provide significant improvement over the algebraic and the half-equation models but have their own limitations. The Baldwin-Barth model overpredicts separation and underpredicts reattachment. In contrast, the Spalart-Allmaras model underpredicts separation and overpredicts reattachment.

Srinivasan, G. R.↗

Hot-Film and Hot-Wire Anemometry for a Boundary Layer Active Flow Control Test

Unsteady active flow control (AFC) has been used experimentally for many years to minimize bluff-body drag. This technology could significantly improve performance of rotorcraft by cleaning up flow separation. It is important, then, that new actuator technologies be studied for application to future vehicles. A boundary layer wind tunnel was constructed with a 1ft-x-3ft test section and unsteady measurement instrumentation to study how AFC manipulates the boundary layer to overcome adverse pressure gradients and flow separation. This unsteady flow control research requires unsteady measurement methods. In order to measure the boundary layer characteristics, both hot-wire and hot-film Constant Temperature Anemometry is used. A hot-wire probe is mounted in the flow to measure velocity while a hot-film array lays on the test surface to measure skin friction. Hot-film sensors are connected to an anemometer, a Wheatstone bridge circuit with an output that corresponds to the dynamic flow response. From this output, the time varying flow field, turbulence, and flow reversal can be characterized. Tuning the anemometers requires a fan test on the hot-film sensors to adjust each output. This is a delicate process as several variables drastically affect the data, including control resistance, signal input, trim, and gain settings.

Control Test↗

Characterizing NWP Model Errors Using Doppler-Lidar Measurements of Recurrent Regional Diurnal Flows: Marine-Air Intrusions into the Columbia-River Basin

Ground-based Doppler-lidar instrumentation provides atmospheric wind data at dramatically improved accuracies and spatial/temporal resolutions. These capabilities have provided new insights into atmospheric flow phenomena, but they also should have a strong role in NWP model improvement. Insight into the nature of model errors can be gained by studying recurrent atmospheric flows, here a regional summertime diurnal sea breeze and subsequent marine-air intrusion into the arid interior of Oregon-Washington, where these winds are an important windenergy resource. These marine intrusions were sampled by three scanning Doppler lidars in the Columbia-River Basin as part of the Second Wind Forecast Improvement Project (WFIP2), using data from summer 2016. Lidar time-height cross sections of wind speed identified eight days when the diurnal-flow cycle, (peak wind speeds at midnight, afternoon minima) was obvious and strong. Eight-day composite time-height cross sections of lidar wind speeds are used to validate those generated by the operational NCEP-HRRR model. HRRR simulated the diurnal wind cycle, but produced errors in the timing of onset and significant errors due to a premature nighttime demise of the intrusion flow, producing low-bias errors of 6 m s-1 . Day-to-day and in the composite, whenever a marine intrusion occurred, HRRR made these same errors. The errors occurred under a range of gradient wind conditions indicating that they resulted from the misrepresentation of physical processes within a limited region around the measurement locations. Because of their generation within a limited geographical area, field-measurement programs can be designed to find and address the sources of these NWP errors.

Banta, Robert M.↗

A model for simulating adaptive, dynamic flows on networks: Application to petroleum infrastructure

Simulation models can greatly improve decisions meant to control the consequences of disruptions to critical infrastructures. We describe a dynamic flow model on networks purposed to inform analyses by those concerned about consequences of disruptions to infrastructures and to help policy makers design robust mitigations. We conceptualize the adaptive responses of infrastructure networks to perturbations as market transactions and business decisions of operators. We approximate commodity flows in these networks by a diffusion equation, with nonlinearities introduced to model capacity limits. To illustrate the behavior and scalability of the model, we show its application first on two simple networks, then on petroleum infrastructure in the United States, where we analyze the effects of a hypothesized earthquake.

02 PETROLEUM↗