Search NASA⌕ Search

SEARCH · Search NASA

Results for “module efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Method of differential-phase/absolute-amplitude QAM

A method of quadrature amplitude modulation involving encoding phase differentially and amplitude absolutely, allowing for a high data rate and spectral efficiency in data transmission and other communication applications, and allowing for amplitude scaling to facilitate data recovery; amplitude scale tracking to track-out rapid and severe scale variations and facilitate successful demodulation and data retrieval; 2.sup.N power carrier recovery; incoherent demodulation where coherent carrier recovery is not possible or practical due to signal degradation; coherent demodulation; multipath equalization to equalize frequency dependent multipath; and demodulation filtering.

97 MATHEMATICS AND COMPUTING↗

A 4 x 4 array module of position-sensitive virtual Frisch-grid CdZnTe detectors for gamma-ray imaging spectrometers

Arrays of position-sensitive virtual Frisch-grid CdZnTe (CZT) detectors offer an economical approach to making high efficiency and high energy resolution gamma cameras for spectroscopy and imaging of radioactive sources. There are many application areas for such instruments including gamma-rays astronomy, medical and industrial imaging, nonproliferation and nuclear safeguards. We present the test results from a 4x4 array module coupled to the front-end ASIC. The array houses 16 detectors made of 6x6x20 mm 3 CZT crystals. Each crystal is encapsulated inside an ultrathin polyester shell and furnished with four 5-mm-wide charge-sensing pads placed near the anode on each side of the detector. The pad’s signals are used to measure X-Y coordinates while the cathode signals give the interaction depths (Z coordinates). Combined together the signals provide 3D position information of the interaction points which can be used to correct the detector response non-uniformity. This allows developers to use standard grade (unselected) CZT crystals while retaining high spectroscopic performance comparable with that of the H3D pixelated detectors. The array’s design provides flexibility to replace individual detectors and extend their sizes, potentially increasing upwards of 4 cm in height. We started development of position-sensitive VFG detectors several years ago and today this technology has reached a high-maturity level and is ready to use in practical applications.

3D charge-loss correction↗

Pulse modulated microwave operation on large bore electron cyclotron resonance ion source with cylindrically comb-shaped magnetic fields configuration

In order to enhance efficiency of an electron cyclotron resonance (ECR) plasma for broad and dense ion beam source under the low pressure, the magnetic field configuration is constructed by a pair of comb-shaped magnet which has opposite polarity each other, and which cylindrically surrounds the plasma chamber. By using the pulse microwave mode operation, we aim at generation of plasma with parameters that cannot be achieved at the continuous microwave (cw) mode. The maximum beam current is obtained in the experimental condition of the pulse width 100-200 {mu}s at the duty ratio 40%-50%. According to probe measurements of the ECR plasma, it is found the electron density in the pulse mode is larger than that in the cw mode, while the electron temperatures in the pulse mode were lower than that in the cw mode. These indirect evidences cause to enhance ion beams in the pulse mode operation, and then suggest a spread of operation windows for plasma parameters suitable to production of molecular or cluster ions.

43 PARTICLE ACCELERATORS↗

Simultaneous photonic generation of multiple chirp and unchirp microwave waveform with frequency multiplying capability for optical beam forming system

A photonic technique based on the Mach–Zehnder Modulator and the dual parallel Mach–Zehnder modulator is proposed for the simultaneous generation of multiple chirp and unchirp microwave waveform with frequency multiplying capability for efficient beam steering applications. There is provision to obtain a single chirp signal of a particular center frequency and chirp rate from a multiple chirp signal without any alternation in the experimental setup. In the proposed methodology, the PIN photodetector is used for the detection of 12 GHz unchirp microwave waveform showing the frequency doubling characteristics and the balance photodetector is used for the detection of multiple chirp signal with frequency components 6, 12, and 18 GHz. The same experimental setup is used to generate dual linear chirp microwave signal of 12 GHz center frequency. This can be achieved by adjusting the bias voltage of the phase modulator. Time bandwidth product and bandwidth of the signal are 18.33 and 410 MHz, respectively. This technique is tunable in frequency, but the generation of higher frequency microwave signals is limited by the speed and bandwidth of the Mach–Zehnder Modulator and photodetector. The novelty of our proposed scheme is that we are going to drive MZM by chirp RF signal to multiply the chirp rate in manifold. To the best of our knowledge the effect of chirp microwave signal on photonic highly steerable beam forming system has not yet been studied experimentally in past, which we are targeting under this paper. It is expected that the range of beam steering performance should be improved substantially as compared to previously reported results.

42 ENGINEERING↗

Small Reactors in Microgrids: Technology Modeling and Selection (Net-Zero Microgrid Program Project Report)

This report demonstrates the capabilities of the net-zero microgrid (NZM) Xendee platform for modeling an SR module with electricity, heat extraction and thermal storage in microgrids configurations. The model effectively captures the most important technical and economic considerations for SR technology specific analysis: cost and operational characteristics of SR technology and financial costs and incentives. The model can analyze multiple scenarios to establish metrics for cost-competitive and zero-carbon microgrids connected to the grid or completely isolated. The model is fully integrated within the Xendee platform for modeling and analysis of clean energy microgrids with storage and generation from renewable energy sources. The model captures the capabilities, constraints, and nuances of SR by incorporating parameters related to plant economics, design efficiency and performance, plant operation and component and fuel lifespan. The cost and operational parameters modeled in the SR module are specific to the technology selected for integration in the microgrid. Cost parameters recognize advanced nuclear technology for modular production and installation based on economies of scale from factory manufacture and related commissioning, and cost reduction through technology maturation—first-of-a-kind (FOAK) and nth-of-a-Kind (NOAK). The cost parameters include installation, operations and maintenance (O&M), fuel refueling cycle, and reactor life. Installation cost reflects economies of scale due to unit sizing at scale and colocation. O&M economies of scale for both fixed- and variable-cost fuel life-cycle costs are incurred at every refueling interval, with separate front- and back-end fuel costs, as well as waste-handling and disposition costs. This report investigates key characteristics of different SR technologies suitable for microgrid applications, including design principles, sizing, coolant properties, temperature ratings, fuel structures, and life-cycle considerations. This also includes fuel technologies applicable to these SR systems, alongside strategies for nuclear-waste and spent-fuel management and approaches to address safety, security, and proliferation challenges. Four primary groups of SR technologies are examined: water-cooled, liquid-metal-cooled, high-temperature gas-cooled, and molten-salt-cooled systems. In this report, an initial guideline for technology selection is established, aligning the characteristics of the technologies with the requirements of microgrids. The selection of technology in a microgrid is influenced by various factors, including financial capacity, location and accessibility, demand type and characteristics, reliability and resilience requirements, area constraints, and the lifespan of the microgrid. The types of electrical and non-electrical applications within the microgrid also play a significant role in technology selection. The characteristics of SRs, such as their smaller size, modularity, transportability, long refueling interval, improved safety features, ability to operate in autonomous or semi-autonomous mode, and provision of high-grade heat, are particularly appealing for microgrids. Furthermore, a list of considerations for implementing SRs in microgrids is outlined. The SR model is created to be continuously improved with the acquisition of actual data on investment and operational costs, experience with supply chains, production at scale, and field deployments. In the near term, performance data on applications in microgrids will become available from lessons learned from laboratory tests, such as those planned for the Microreactor Applications Research Validation and Evaluation Project (MARVEL), led by Idaho National Laboratory (INL). The SR model incorporates scenario data and known SR design specifications, enabling technoeconomic analysis for SR deployment in microgrids. It specifically considers the distinctive attributes of SRs as generators in technoeconomic studies. SRs can be modeled and analyzed with generation from renewable-energy sources, energy storage, and flexible loads over a range of functionality and applications. This offers a comprehensive tool for feasibility studies, scenario development, and sensitivity analysis for “what-if” consideration of any range of assumptions about SRs in microgrids and other aggregations of distributed-energy resources, including virtual power plants.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The Effect of EGR on Knock Suppression, Efficiency, and Emissions in a Stoichiometric

Exhaust gas recirculation (EGR) is widely employed on internal combustion engines for NOx reduction and knock suppression. In this study a comprehensive analysis was performed to determine the effect of EGR on efficiency, emissions, and knock suppression of stoichiometric, spark ignited, natural gas engines. Tests were conducted using a single cylinder, variable compression ratio, cooperative fuel research (CFR) engine at 900 RPM, engine load of 800 kPa indicated mean effective pressure (IMEP), and stoichiometric conditions. The tests were performed using a custom EGR system capable of providing a range of EGR displacement rates from 0% to 40% of the intake charge at engine power levels between 1.5 and 3.5 kW. The experimental measurements included the variance of EGR rate, compression ratio, boost pressure, and location of 50% mass fraction burned (CA50). CA50 was controlled with ignition timing using a Woodward Large Engine Control Module. The use of EGR was found to expand the knock limit, while reducing NOx emissions and increasing engine efficiency as much as 4.5% through increased compression ratio and power density. The highest EGR rate that demonstrated beneficial gains on the CFR engine was 23%; the optimal EGR rate was found to be 19%.

Bayliff, Scott↗

The Effect of EGR on Knock Suppression, Efficiency, and Emissions in a Stoichiometric, Spark Ignited, Natural Gas Engine

Exhaust gas recirculation (EGR) is widely employed on internal combustion engines for NOx reduction and knock suppression. In this study a comprehensive analysis was performed to determine the effect of EGR on efficiency, emissions, and knock suppression of stoichiometric, spark ignited, natural gas engines. Tests were conducted using a single cylinder, variable compression ratio, cooperative fuel research (CFR) engine at 900 RPM, engine load of 800 kPa indicated mean effective pressure (IMEP), and stoichiometric conditions. The tests were performed using a custom EGR system capable of providing a range of EGR displacement rates from 0% to 40% of the intake charge at engine power levels between 1.5 and 3.5 kW. The experimental measurements included the variance of EGR rate, compression ratio, boost pressure, and location of 50% mass fraction burned (CA50). CA50 was controlled with ignition timing using a Woodward Large Engine Control Module. The use of EGR was found to expand the knock limit, while reducing NOx emissions and increasing engine efficiency as much as 4.5% through increased compression ratio and power density. The highest EGR rate that demonstrated beneficial gains on the CFR engine was 23%; the optimal EGR rate was found to be 19%.

Cooperative Fuel Research Engine, Exhaust Gas Reci↗

New Packing Structure of Concentration Solar Receiver

This paper presents a solution to the temperature issue in High Concentration Photovoltaic (HCPV) module device by using different thermal conductive material and packing structure. In general, the open-circuited voltage of a device reduces with the increase of temperature and therefore degrades its efficiency. The thermal conductive material we use in this paper, silicon, has a high thermal conductive coefficient (149 W/m{center_dot}K) and steady semiconductor properties which are suitable for the application of solar receiver in HCPV module. Solar cell was soldered on a metal-plated Si substrate with a thicker SiO{sub 2} film which acts as an insulating layer. Then it was mounted on an Al-based plate to obtain a better heat dissipating result.

36 MATERIALS SCIENCE↗

Occupancy Simulation in Three Residential Research Houses

Three houses of similar floor plan are being compared for energy consumption. The first house is a typical builder house of 2400 ft2 (223 m2) in east Tennessee. The second house contains retrofits available to a home owner such as energy efficient appliances, windows and HVAC, as well as an insulated attic which contains HVAC duct work. The third house was built using optimum-value framing construction with photovoltaic modules and solar water heating. To consume energy researchers have set up appliances, lights, and plug loads to turn on and off automatically according to a schedule based on the Building America Research Benchmark Definition. As energy efficiency continues to be a focus for protecting the environment and conserving resources, experiments involving whole house energy consumption will be done. In these cases it is important to understand how to simulate occupancy so that data represents only house performance and not human behavior. The process for achieving automated occupancy simulation will be discussed. Data comparing the energy use of each house will be presented and it will be shown that the third house used 66% less and the second house used 36% less energy than the control house in 2010. The authors will discuss how energy prudent living habits can further reduce energy use in the third house by 23% over the average American family living in the same house.

Boudreaux, Philip R↗

Recycling the Energy of Indoor Light: Highly Efficient Organic Photovoltaics via a Ternary Strategy

A ternary approach in organic photovoltaics (OPV) is simple and reliable to effectively tune the optical, electrical and morphological properties of the photoactive layer for high efficiency as well as long-term stability under 1 sun. However, there have been few papers reporting spectra and weak illumination compared to outdoor light. In this study, by using two compatible 16 structures, we demonstrate a simultaneous modulation of light absorption and molecular donor polymers (PM7 and PM7 D1) with slightly-different band gaps and similar chemical packing under ambient conditions, which resulted in efficient indoor OPVs exhibiting power conversion efficiency (PCE) over 20% under 1000 lux of warm white light-emitting diode (2900 K). From morphological analysis, we infer that PM7 serves to seed nucleation of PM7 D1 in the ternary blend, templating its crystallization and alignment along the PM7 backbone. Such templating effect leads to increased domain spacing and relative degree of crystallinity (rDoC) compared to those of each binary system. We further show that higher rDoC helps suppress both bimolecular and trap-assisted recombination of photogenerated charges in the ternary devices. As a result, the complementary absorption and synergistic molecular assembly of the two donor polymers enhance the short-circuit current density as to increase the average PCEs from 9.6 to 10.3% under 1 sun and from 18.7 to 20.0% under 1000 lux. We envision that our strategy of incorporating both a planar and a flexible donor polymer with similar chemical structures can be generally applicable to attain a high performance ternary OPV under both 1 sun and indoor light.

14 SOLAR ENERGY↗

Maximizing selectivity: An analysis of isoporous membranes

Membranes are compelling candidates for many separation-based industrial processes. However, all synthetic membranes are subject to well-recognized permeability-selectivity trade-offs that hinder their use in advanced applications. Having uniform nanoscale pore size, isoporous nanofiltration and ultrafiltration membranes have attracted wide research interest. However, quantitative analysis of isoporous membrane performance is lacking - particularly at module and system-level scales. In this study, an analytical model is built to investigate how membrane pore-size distribution affects the solute separation efficiency (i.e., rejection and selectivity). The model accounts for convective hindrance as well as concentration polarization and explores effects on separation from the solute-to-pore-size ratio and percent recovery (i.e., fraction of feed flow that passes through the membrane). At the module level, our analysis suggests that a notably sharper rejection vs. solute size curve can be obtained as the pore-size distribution becomes narrower. Additionally, as the recovery increases, the rejection of a solute is maintained at a high level using isoporous membranes while the rejection drops rapidly for membranes that possess a disperse pore-size distribution. Furthermore, in the separation of mixed solutes, isoporous membranes achieve a large selectivity with a modest loss of permeability. Overall, this study elaborates the unique role that isoporous membranes play within the permeability-selectivity trade-off relations and identifies the most exciting opportunities for their future applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Spectral dispersion of the linewidth enhancement factor and four wave mixing conversion efficiency of an InAs/GaAs multimode quantum dot laser

The spectral dependence of the linewidth enhancement factor (αH-factor) of a multimode InAs/GaAs quantum dot laser is analyzed. Amplified spontaneous and high-frequency modulation methods are used to experimentally retrieve the αH-factor of each longitudinal mode below and above the threshold. A dispersion of the αH-factor is unlocked across the entire optical spectrum, which is further illustrated in the context of four wave mixing experiments. The results show that the induced conversion efficiency is increased at lasing wavelengths where the linewidth enhancement is lower. These results highlight the importance of carefully monitoring the linewidth enhancement factor in quantum dot lasers especially for frequency combs and mode-locking applications in future optical communication systems.

Ding, Shihao (ORCID:0000000346416944)↗

Solar Thermochemical Fuel Production via a Novel Low Pressure, Magnetically Stabilized, Non-volatile Iron Oxide Looping Process (University of Florida)

The UF Solar Fuels team has developed a modular reactor at the 10kW scale for the thermochemical conversion of H 2 O and CO 2 to H 2 and CO, respectively, using concentrated solar energy to drive high-temperature redox reactions. Various materials, including ferrites, doped and mixed metal ferrites, and ceria, were investigated and reported on. Ceria was chosen as the reactive material, with thermogravimetric and bench-scale analysis concurring with literature review and pointing towards reasonable kinetics and stability at temperatures on the order of 1500°C. A combined radiation, conduction, and species reaction/mass transport model was developed, utilizing Monte Carlo ray tracing, Lattice Boltzmann, and random walk particle tracking for the respective components to direct development and optimization of the reactor. With experimental data used for reaction rates, the model showed a path to efficiencies >20%, which could be market competitive with current PV-hydrolysis hydrogen generation systems. Economic analysis of a larger-scale plant (100kW modular system with cost performed at 500 modules) has been performed, assuming 0.5% and 10% internal rate of return. Without compression costs, H 2 production cost using this is technology at 12 USD/kg H 2 and 17 USD/kg H 2 for realized efficiencies of 20% and 15%, respectively.

14 SOLAR ENERGY↗

Optics-based approach to thermal management of photovoltaics: Selective-spectral and radiative cooling

For commercial one-sun solar modules, up to 80% of the incoming sunlight may be dissipated as heat, potentially raising the temperature 20-30 °C higher than the ambient. In the long term, extreme self-heating erodes efficiency and shortens lifetime, thereby dramatically reducing the total energy output. Therefore, it is critically important to develop effective and practical (and preferably passive) cooling methods to reduce operating temperature of photovoltaic (PV) modules. In this paper, we explore two fundamental (but often overlooked) origins of PV self-heating, namely, sub-bandgap absorption and imperfect thermal radiation. The analysis suggests that we redesign the optical properties of the solar module to eliminate parasitic absorption (selective-spectral cooling) and enhance thermal emission (radiative cooling). Comprehensive opto-electro-thermal simulation shows that the proposed techniques would cool one-sun terrestrial solar modules up to 10 °C. As a result, this self-cooling would substantially extend the lifetime for solar modules, with corresponding increase in energy yields and reduced levelized cost of electricity.

14 SOLAR ENERGY↗

Habit–Dependent Vapor Growth Modulates Arctic Supercooled Water Occurrence

We present an analysis of long-term data collected at Utqiagvik, Alaska, to explore the impacts of cloud processes on the probability of finding supercooled water given cloud temperature, P(L|T), in the topmost unseeded liquid-bearing layers. P(L|T) has local minima at temperatures around –6°C and –15°C. Simulations using habit-evolving ice microphysics models suggest that these minima are the result of efficient vapor growth by non-isometric habits found at these temperatures. Here, we conclude that habit-dependent vapor growth of ice crystals modulates the macrophysical occurrence of supercooled water in polar clouds, the effect of which should be included in model parametrizations to avoid biases and/or error compensation. Our methodology is adaptable for spherical ice treatments implemented in models (example parametrizations provided), amenable for use with satellite measurements to give global impartial observational targets for model evaluations, and may allow empirical characterization of bulk responses to seeding and possibly secondary ice effects.

54 ENVIRONMENTAL SCIENCES↗

Proline- and Arginine-Rich Peptides as Flexible Allosteric Modulators of Human Proteasome Activity

Proline- and arginine-rich peptide PR11 is an allosteric inhibitor of 20S proteasome. We modified its sequence inter alia by introducing HbYX, RYX, or RHbX C-terminal extensions (Hb, hydrophobic moiety; R, arginine; Y, tyrosine; X, any residue). Consequently, we were able to improve inhibitory potency or to convert inhibitors into strong activators: the former with an aromatic penultimate Hb residue and the latter with the HbYX motif. The PR peptide activator stimulated 20S proteasome in vitro to efficiently degrade protein substrates, such as α-synuclein and enolase, but also activated proteasome in cultured fibroblasts. The positive and negative PR modulators differently influenced the proteasome conformational dynamics and affected opening of the substrate entry pore. The resolved crystal structure showed PR inhibitor bound far from the active sites, at the proteasome outer face, in the pocket used by natural activators. Overall, our studies indicate the opportunity to tune proteasome activity by allosteric regulators based on PR peptide scaffold.

60 APPLIED LIFE SCIENCES↗

All-optical Time-resolved Measurement of Laser Energy Modulation in a Relativistic Electron Beam

Hamiltonian light-front theory has been proposed as a promising method for solving bound states problems in quantum field theory a long time ago, see, e.g., the review article[1] for its various advantages compared to the traditional instant-form theories. Recently the Basis Light-Front Quantization (BLFQ) approach [2, 3] has been developed as a nonperturbative approach to solve Hamiltonian light-front quantum field theory. Numerical efficiency is a key advantage of this approach. The basic idea of BLFQ is to represent the theory in an optimal basis which respects many symmetries of the theory and thus minimizes the dimensionality of the Hamiltonian for a fixed precision. Specifically, the BLFQ approach employs a plane wave basis in the light-front longitudinal direction and a 2D harmonic oscillator basis in the transverse directions. In previous work [3] this approach has been applied to evaluate the anomalous magnetic moment of electrons which are confined in an external trap with an extrapolation to the zero trap limit. In this work we extend and improve this approach in several aspects including the direct evaluation of a free electron system. This article is organized as follows: In Sec. 2 we discuss the key extensions and improvements made in this work over Ref [3]; in Sec. 3 we present the numerical results for the electron anomalous magnetic moment evaluated in different harmonic oscillator bases and compare to the perturbation theory result. Finally we conclude and give an outline for future works in Sec. 4.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗