Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Diffuse reflection from a stochastically bounded, semi-infinite medium

In order to determine the diffuse reflection from a medium bounded by a rough surface, the problem of radiative transfer in a boundary layer characterized by a statistical distribution of heights is considered. For the case that the surface is defined by a multivariate normal probability density, the propagation probability for rays traversing the boundary layer is derived and, from that probability, a corresponding radiative transfer equation. A solution of the Eddington (two stream) type is found explicitly, and examples are given. The results should be applicable to reflection from the regoliths of solar system bodies, as well as from a rough ocean surface.

Lumme, K.↗

Impact of Morphological Features on the Dielectric Breakdown at SiO{sub 2}/3C-SiC Interfaces

Thin SiO{sub 2} layers were thermally grown onto cubic silicon carbide (3C-SiC) heteroepitaxial layers of different surface roughness and with different types of near-surface epitaxial defects. Localized dielectric breakdown (BD) was studied by electrically stressing the system using Conductive Atomic Force Microscopy (C-AFM), which constitutes a means to directly and simultaneously observe localized dielectric failure as a function of stress time and surface morphology with nanoscale lateral resolution. The BD kinetics was evaluated by fitting the experimental failure ratios as a function of stress time to the failure probability described by Weibull statistics, in turn allowing to distinguish between defect-induced (extrinsic) and intrinsic dielectric BD events. The results give useful information about how morphological features at the 3C-SiC surface influence the BD generation in thermally grown oxides on this polytype.

36 MATERIALS SCIENCE↗

Finishing and Inspection of Model Surfaces for Boundary Layer Transition Tests

Techniques which have been used for finishing and quantitatively specifying surface roughness on boundary-layer-transition models are reviewed. The appearance of a surface as far as roughness is concerned can be misleading when viewed either by the eye or with the aid of a microscope. The multiple-beam interferometer and the wire shadow method provide the best simple means of obtaining quantitative measurements.

Wilkins, Max E.↗

Visual Inspection of Surfaces

This presentation evaluates the parameters that affect visual inspection of cleanliness. Factors tested include surface reflectance, surface roughness, size of the largest particle, exposure time, inspector and distance from sample surface. It is concluded that distance predictions were not great, particularly because the distance at which contamination is seen may depend on more variables than those tested. Most parameters estimates had confidence of 95% or better, except for exposure and reflectance. Additionally, the distance at which surface is visibly contaminated decreases with increasing reflectance, roughness, and exposure. The distance at which the surface is visually contaminated increased with the largest particle size. These variables were only slightly affected the observer.

Hughes, David↗

Turbulent boundary layer over solid and porous surfaces with small roughness

The wind tunnel models and instrumentation used as well as data reduction and error analysis techniques employed are described for an experimental study conducted to measure directly skin friction and obtain profiles of mean velocity, axial and normal turbulence intensity, and Reynolds stress in the untripped boundary on a large diameter axisymmetric body. Results are given for such a body with a (1) smooth, solid surface; (2) a sandpaper roughened, solid surface; (3) a sintered metal, porous surface; (4) a ""smooth'' performated titanium surface; (5) a rough, solid surface made of fine diffusion bonded screening; and (6) a rough, porous surface made of the same screening. The roughness values were in low range (k+ 5 to 7) just above what is normally considered ""hydraulically smooth''. Measurements were taken at several axial locations and tow or normal stream freestream velocities, 45.1 m/sec and 53.5 m/sec.

Kong, F. Y.↗

Synthesis of flat sticky hydrophobic carbon diamond-like films using atmospheric pressure Ar/CH{sub 4} dielectric barrier discharge

An Ar/CH{sub 4} atmospheric pressure dielectric barrier discharge (AP-DBD) was used to synthesize sticky hydrophobic diamond-like carbon (DLC) films on glass surface. The film is formed with plasma treatment duration shorter than 30 s, and water contact angles larger than 90° together with contact angle hysteresis larger than 10° can be achieved. According to Fourier transform infrared spectroscopy and atomic force microscopy analysis, hydrocarbon functional groups are created on the glass substrate, producing coatings with low surface energy (∼35 mJ m{sup −2}) with no modification of the surface roughness. To infer the plasma processes leading to the formation of low energy DLC surfaces, optical emission spectroscopy was used. From the results, a direct relationship between the CH species present in the plasma and the carbon concentration in the hydrophobic layer was found, which suggests that the CH species are the precursors of DLC film growth. Additionally, the plasma gas temperature was measured to be below 350 K which highlights the suitability of using AP-DBD to treat thermo-sensitive surfaces.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Impact of controlled prewetting on part formation in binder jet additive manufacturing

Binder jetting is an additive manufacturing process that bonds powder through selectively depositing binder by inkjet printing. The part is then extracted and densified by sintering and/or infiltration. The process offers low costs and fast build rates, but properties can be poor due to residual porosity after sintering. The inkjet printing process may contribute to this residual porosity by creating large pores. The droplet kinetic energy ejects some powder particles from the bed and rearranges others. Particle ejection and rearrangement are theorized to create porous regions in binder-jetted parts. In this work, small amounts of moisture are added to the spread powder before printing and the impact on part formation, part properties, and printing parameters measured with varied droplet spacing, droplet velocity, and print frequency. Moisture is added by applying an atomized fluid mixture to the powder between layer spreading and binder printing. The fluid mixture partially evaporates but leaves a stable residue to increase cohesion and enhance imbibition. Moisture addition to the powder increases the range of droplet spacings for line formation while reducing particle ejection, powder rearrangement, and balling in layer and multilayer parts. Excessive moisture addition decreases the effective saturation of printed lines, but saturation in 3D parts is less impacted. Increased surface roughness in the first few layers of a print was also mitigated with prewetting. Finally, high-speed X-ray imaging verified prewetting reduction in particle ejection and rearrangement.

36 MATERIALS SCIENCE↗

Compact Submillimeter-Wave Receivers Made with Semiconductor Nano-Fabrication Technologies

Advanced semiconductor nanofabrication techniques are utilized to design, fabricate and demonstrate a super-compact, low-mass (<10 grams) submillimeter-wave heterodyne front-end. RF elements such as waveguides and channels are fabricated in a silicon wafer substrate using deep-reactive ion etching (DRIE). Etched patterns with sidewalls angles controlled with 1 deg precision are reported, while maintaining a surface roughness of better than 20 nm rms for the etched structures. This approach is being developed to build compact 2-D imaging arrays in the THz frequency range.

Silicon micromachining↗

A Comparative Evaluation of Additive Manufactured Stainless Steel Test Pieces

Stainless steel is used for variety of applications with different grades, alloys, filaments and powders. Additive manufacturing (AM) enables unique design features and refined microstructures. Performance testing on AM parts are needed as input to modeling and accelerated qualification processes. The objective of this work is to determine the effect of surface roughness on corrosion rate for from different manufacturers Preliminary evaluation shows that the 500-hour data set was scattered, and trend analysis are complex, while the 1000h and 1500h test results evaluation show more distinct trends.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Online monitoring of a belt grinding process by using a light scattering method

Industrially ground surfaces often have a characteristic surface topography known as chatter marks. The surface finishing is mainly monitored by optical measurement techniques. In this work, the monitoring of an industrial belt grinding process with a light scattering sensor is presented. Although this technique is primarily applied for parametric surface roughness analysis, here it is shown that it enables also the measurement of the surface topography, i.e., the chatter marks occurring during the belt grinding process. In particular, it is proven that the light scattering method is appropriate to measure online the topography of chatter marks. Furthermore, the frequency analysis of the data reveals that the wavelength of chatter marks strongly depends on process parameters, such as the grinding speed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Influence of Surface Morphology on the Shear-Induced Wear of Alkylsilane Monolayers: Molecular Dynamics Study

Chemisorbed alkylsilane monolayer coatings have been shown to possess favorable lubrication properties; however, film degradation prevents the widespread use of these materials as lubricants in micro- and nanoelectromechanical systems (MEMS/NEMS). In this work, molecular dynamics (MD) simulations are used to provide insight into the conditions that promote the degradation and wear of these materials. This is achieved through removal of interfacial chain-substrate bonds during shear and the examination of the mobility of the resulting free, unbound chains. Specific focus is given to the effects of surface morphology, which has been shown previously to strongly influence frictional forces in monolayer systems. In-plane order of chain attachments is shown to lead to pressure-induced orientational ordering of monolayers, promoting film stability. This behavior is lost as nonideality is introduced into the substrate and chain patterning on the surface becomes disordered. The presence of surface roughness is found to reduce film stability, with localization of wear observed for chain attachment sites nearest the interface of contact. Furthermore, the influence of substrate nonideality on monolayer degradation is shown to diminish as chain length is increased.

99 GENERAL AND MISCELLANEOUS↗

Growth of high-quality SrTiO{sub 3} films using a hybrid molecular beam epitaxy approach

A hybrid molecular beam epitaxy approach for atomic-layer controlled growth of high-quality SrTiO{sub 3} films with scalable growth rates was developed. The approach uses an effusion cell for Sr, a plasma source for oxygen, and a metal-organic source (titanium tetra isopropoxide) for Ti. SrTiO{sub 3} films were investigated as a function of cation flux ratio on (001) SrTiO{sub 3} and (LaAlO{sub 3}){sub 0.3}(Sr{sub 2}AlTaO{sub 6}){sub 0.7} (LSAT) substrates. Growth conditions for stoichiometric insulating films were identified. Persistent (>180 oscillations) reflection high-energy electron diffraction oscillation characteristic of layer-by-layer growth were observed. The full widths at half maximum of x-ray diffraction rocking curves were similar to those of the substrates, i.e., 34 arc sec on LSAT. The film surfaces were nearly ideal with root mean square surface roughness values of less than 0.1 nm. The relationship between surface reconstructions, growth modes, and stoichiometry is discussed.

36 MATERIALS SCIENCE↗

Characterization of electroless nickel-phosphorus plating for ultracold-neutron storage

Electroless nickel plating is an established industrial process that provides a robust and relatively low-cost coating suitable for transporting and storing ultracold neutrons (UCN). Using roughness measurements and UCN-storage experiments we characterized UCN guides made from polished aluminum or stainless-steel tubes plated by several vendors. All electroless nickel platings were similarly suited for UCN storage with an average loss probability per wall bounce of 2.8 • 10 -4 to 4.1 • 10 -4 for energies between 90 neV and 190 neV, or a ratio of imaginary to real Fermi potential η of 1.7 • 10 -4 to 3.3 • 10 -4 . Measurements at different elevations indicate that the energy dependence of UCN losses is well described by the imaginary Fermi potential. Some special considerations are required to avoid an increase in surface roughness during the plating process and hence a reduction in UCN transmission. Increased roughness had only a minor impact on storage properties. In conclusion, based on these findings we chose a vendor to plate the UCN-production vessel that will contain the superfluid-helium converter for the new TRIUMF UltraCold Advanced Neutron (TUCAN) source, achieving acceptable UCN-storage properties with η = 3.5(5)•10 -4 .

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

SmaggIce Version 1.8

SmaggIce version 1.8 is a set of software tools for geometrical modeling of, and generation of grids that conform to, both clean and iced airfoils. Ice shapes, especially those that include rough surfaces, pose difficulty in generating high-quality grids that are essential for predicting airflows by use of computational fluid dynamics. SmaggIce version 1.8 contains software tools needed to overcome this difficulty. For a given airfoil, it allows the user to define the flow domain, decompose the domain into blocks, generate grids, merge gridded blocks, and control the density and smoothness of each grid. Among the unique features of version 1.8 is a thin C-shaped block, called a "viscous sublayer block," which is wrapped around an iced airfoil and its wake line and serves as a means to generate highly controlled grids near the rough ice surface. Users can modify block boundary shapes using control points of non-uniform rational B-spline (NURBS) curves. Concave ice regions can be smoothed during geometrical modeling or creation of the viscous sublayer block.

Vickerman, Mary B.↗

Experimental and theoretical investigations on the adherent behaviors of high viscosity liquid: The effect of surface topography

Wetting test and classical molecular dynamics (MD) simulations were employed to investigate the adherent behaviors of hydroxyl-terminated polybutadiene (HTPB), a typical high viscosity liquid widely used as a binder in rocket motor propellants, onto the copper (Cu) surfaces with different topographies. Experimental data show that the microstructures protruding above the substrate surfaces can be ‘sensed’ by the HTPB droplet, which has been indicated by the smaller contact angles and higher interface tension for this specific liquid on the rough surfaces (featured with sinusoidal structures or square pillars) than that on the smooth surface. Simulation results reveal the atomic details of spreading process of HTPB chains, with diverse diffusion propensities presented on different surfaces. The HTPB droplet spreads widely on the smooth surface, exhibiting a roughly isotropic trend. On the contrary, the state of this high viscosity liquid on the sinusoidal-structured surface is featured by wide contact diffusion along the run of groove, but relatively restricted extension in the direction perpendicular to the groove, as a result of the barriers exerted by the nearest neighbouring peaks. The existence of nanoscale pillars increases the exterior surface area of Cu substrate, therefore the HTPB chains can penetrate deep to envelop the peripheries of the pillars, forming abundant direct contacts with Cu surface and producing a highest HTPB–Cu interaction energy, which well accords with the experimental results about the adherent strength of HTPB.

Wu, Chunya↗

Assessment of Transition Modeling Capability in OVERFLOW with Emphasis on Swept-Wing Configurations

In preparation for comparisons with data obtained from the recently concluded experiments in the National Transonic Facility at the NASA Langley Research Center on the new common research model with natural laminar flow (CRM-NLF), an assessment of the current transition modeling capability in the NASA OVERFLOW 2.2o code has been carried out. A combination of the available experimental data and linear stability analysis is used to evaluate the accuracy and robustness of these models for selected swept-wing type configurations, with significant crossflow. An additional goal for this work involves providing a comparative assessment of the relevant transition models in the context of a single flow solver and identifying model limitations as well as the potential for future improvements that would help strengthen the physical basis of such transition models. Included in this investigation is an assessment of the sensitivities of the underlying transition models to grid resolution (wall-normal, as well as streamwise and spanwise) and the values of extra input parameters such as the level of surface roughness and freestream turbulence variables. The flow configurations targeted in this assessment include the NASA NLF(2)-0415 swept-wing configuration, the sickle-shaped wing introduced by the Technical University of Braunschweig, and the wing-body configuration of the CRM model from the fourth and fifth AIAA CFD Drag Prediction Workshops.

Freestream velocity↗

Characterization of Polyamide Thin Films by Atomic Force Microscopy

This study directly compares the mechanical behavior of novel molecular layer deposition (MLD) and analogous interfacial polymerization (IP) polyamide thin films in environments relevant to reverse osmosis (RO) membrane operation. The elastic modulus of the films was determined using atomic force microscopy (AFM) in dry, hydrated, and chlorinated states. Surface roughness characteristics were also obtained given their potential influence on AFM modulus measurements. The much smoother MLD films demonstrated a statistically higher modulus in all states as compared to their IP counterparts. The MLD films maintained a modulus ~3X and ~5X greater than that of IP films after hydration and chlorination, respectively. Such differences in behavior may be due to the higher density and correspondingly lower void content of the MLD films. Results from this study provide a rationale for future development of MLD for fabrication of polyamide films for incorporation in RO membranes.

atomic force microscopy↗

Transition Experiments on Blunt Bodies with Isolated Roughness Elements in Hypersonic Free Flight

Smooth titanium hemispheres with isolated three-dimensional (3D) surface roughness elements were flown in the NASA Ames hypersonic ballistic range through quiescent CO2 and air environments. Global surface intensity (temperature) distributions were optically measured and thermal wakes behind individual roughness elements were analyzed to define tripping effectiveness. Real-gas Navier-Stokes calculations of model flowfields, including laminar boundary layer development in these flowfields, were conducted predict key dimensionless parameters used to correlate transition on blunt bodies in hypersonic flow. For isolated roughness elements totally immersed within the laminar boundary layer, critical roughness Reynolds numbers for flights in air were found to be higher than those measured for flights in CO2, i.e., it was easier to trip the CO2 boundary layer to turbulence. Tripping effectiveness was found to be dependent on trip location within the subsonic region of the blunt body flowfield, with effective tripping being most difficult to achieve for elements positioned closest to the stagnation point. Direct comparisons of critical roughness Reynolds numbers for 3D isolated versus 3D distributed roughness elements for flights in air showed that distributed roughness patterns were significantly more effective at tripping the blunt body laminar boundary layer to turbulence.

Reda, Daniel C.↗