Search NASA⌕ Search

SEARCH · Search NASA

Results for “Composite testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Exploratory investigation of two resin-matrix composites subjected to arc-tunnel heating

Flexture and short beam shear specimens of a graphite epoxy and a graphite polymimide composite material were tested in an arc tunnel environment. The materials were subjected to seven heating rates from 12.5 to 308 kW/sw m for test times from 5 to 1000 seconds. The temperature response of the specimens was measured and the strength degradation caused by the various heating environments was determined.

Pittman, C. M.↗
NASA NTRS1979

Low-velocity impact damage in graphite-fiber reinforced epoxy laminates

An experimental investigation was conducted to identify the failure mechanisms and to understand damage propagation in compression-loaded composite structures. The tests were conducted on several laminates of different ply orientation with thickness that ranged from 0.56 to 0.75 cm. The panels were damaged by 1.27-cm-diameter aluminum spheres propelled normal to the specimen surface at velocities ranging from 30 m/s to 140 m/s. Results indicate that there is significant internal laminate damage due to low-velocity impact with no surface damage. The internal damage consists of delamination and intraply cracking. Three damage propagation modes were identified as causing specimen failure; which are delamination, axial load-lateral deformation coupling, and local shear failure.

Rhodes, M. D.↗
NASA NTRS1980

Influence of quality control variables on failure of graphite/epoxy under extreme moisture conditions

Tension tests on graphite/epoxy composites were performed to determine the influence of various quality control variables on failure strength as a function of moisture and moderate temperatures. The extremely high and low moisture contents investigated were found to have less effect upon properties than did temperature or the quality control variables of specimen flaws and prepreg batch to batch variations. In particular, specimen flaws were found to drastically reduce the predicted strength of the composite, whereas specimens from different batches of prepreg displayed differences in strength as a function of temperature and extreme moisture exposure. The findings illustrate the need for careful specimen preparation, studies of flaw sensitivity, and careful quality control in any study of composite materials.

Clements, L. L.↗
NASA NTRS1982

Fatigue and fracture research in composite materials

The fatigue, fracture, and impact behavior of composite materials are investigated. Bolted and bonded joints are included. The solutions developed are generic in scope and are useful for a wide variety of structural applications. The analytical tools developed are used to demonstrate the damage tolerance, impact resistance, and useful fatigue life of structural composite components. Standard tests for screening improvements in materials and constituents are developed.

T. Kevin O'Brien↗
NASA NTRS1982

Effects of simulated lightning on composite and metallic joints

The effects of simulated lightning strikes and currents on aircraft bonded joints and access/inspection panels were investigated. Both metallic and composite specimens were tested. Tests on metal fuel feed through elbows in graphite/epoxy structures were evaluated. Sparking threshold and residual strength of single lap bonded joints and sparking threshold of access/inspection panels and metal fuel feed through elbows are reported.

Howell, W. E.↗
NASA NTRS1983

Hygrothermomechanical evaluation of transverse filament tape epoxy/polyester fiberglass composites

The static and cyclic load behavior of transverse filament tape (TFT) fiberglass/epoxy and TFY fiberglass/polyester composites, intended for use in the design of low-cost wind turbine blades, are presented. The data behavior is also evaluated with respect to predicted properties based on an integrated hygrothermomechanical response theory. Experimental TFT composite data were developed by the testing of laminates made by using composite layups typical of those used for the fabrication of TFT fiberglass wind turbine blades. Static properties include tension, compression, and interlaminar shear strengths at ambient conditions and at high humidity/elevated temperature conditions after a 500 hour exposure. Cyclic fatigue data were obtained using similar environmental conditions and a range of cyclic stresses. The environmental (temperature and moisture) and cyclic load effects on composite strength degradation are subsequently compared with the predictions obtained by using the composite life/durability theory. The results obtained show that the predicted hygrothermomechanical environmental effects on TFT composites are in good agreement with measured data for various properties including fatigue at different cyclic stresses.

Lark, R. L.↗
NASA NTRS1982

Influence of quality control variables on failure of graphite/epoxy under extreme moisture conditions

Tension tests on graphite/epoxy composites were performed to determine the influence of various quality control variables on failure strength as a function of moisture and moderate temperatures. The extremely high and low moisture contents investigated were found to have less effect upon properties than did temperature or the quality control variables of specimen flaws and prepreg batch to batch variations. In particular, specimen flaws were found to drastically reduce the predicted strength of the composite, whereas specimens from different batches of prepreg displayed differences in strength as a function of temperature and extreme moisture exposure. The findings illustrate the need for careful specimen preparation, studies of flaw sensitvity, and careful quality control in any study of composite materials. Previously announced in STAR as N80-33493

Clements, L. L.↗
NASA NTRS1982

Development of an advanced composite aileron for the L-1011 transport aircraft

Significant improvements in structural efficiency can be achieved by the utilization of advanced composites for construction of aircraft secondary structures. Careful evaluation of alternate designs and materials for the L-1011 advanced composite inboard aileron has led to the selection of several unique material combinations and easily manufactured structural configurations. The advanced composite aileron is a direct replacement for the metal aileron with a weight savings of 23 percent. Due to the configurational simplicity of the components within the composite aileron, and because it contains 50 percent fewer parts and fasteners than the metal aileron, it is predicted that the composite aileron will be cost competitive with the metal aileron in a production environment. Structural analysis of the composite aileron, in conjunction with the design data, concept verification, and ground tests, indicates that the composite aileron design meets or exceeds structural requirements.

Griffin, C. F.↗
NASA NTRS1983

Thermal and mechanical properties of advanced, high temperature ceramic-composite insulation

It is found that the mechanical properties of fibrous refractory composite insulation (FRCI) can be improved if a higher calcination temperature is used before final processing. The results also reveal that a higher density FRCI containing 60 wt pct aluminoborosilicate fibers will exhibit minimal surface recession at 1480 C in a convective-heating environment. Another finding is that the material performance in the convective-heating environment is limited by the coating and the temperature capability of its emittance agent. A table is included giving the coating compositions used with the composite insulation and tested in the convectively heated environment at a surface temperature of 1480 C.

Leiser, D. B.↗
NASA NTRS1983

The NASA F-106B Storm Hazards Program

During the NASA LRC Storm Hazards Program, 698 thunderstorm precipitations were made from 1980 to 1983 with an F-106B aircraft in order to record direct lightning strike data and the associated flight conditions. It was found that each of the three composite fin caps tested experienced multiple lightning attachments with only minor cosmetic damage. The maximum current level was only 20 ka, which is well below the design standard of 200 ka; however, indications are that the current rate of rise standard has been approached and may be exceeded in a major strike. The peak lightning strike rate occurred at ambient temperatures between -40 and -45 C, while most previously reported strikes have occurred at or near the freezing level. No significant operational difficulties or major aircraft damage resulting from the thunderstorm penetrations have been found.

Neely, W. R., Jr.↗
NASA NTRS1983

Microtektite discovered in Beijing

The discovery, testing, and chemical composition of tiny vitreous spheres are discussed. These spheres, found in China, are thought to be microtektites. A method for determining the age of these spheres is mentioned.

Dingrong, L.↗
NASA NTRS1984

Flywheel containment and safety considerations

Flywheel safety and containment design technology are discussed. The effects of axial loading resulting from composite rotor burst tests are considered. Analysis of the radial burst problem is also included.

Coppa, A. P.↗
NASA NTRS1985

Application of Gr/PMR-15 to commercial aircraft

Following from early experience with polyimides on the SST program and Shuttle aft flap studies the Boeing Company is now working on collaborative programs with its principal nacelle suppliers to pursue the development of Gr/PMR-15 nacelle components. Two programs are currently in effect. The first program is directed specifically towards the flight test and service evaluation at the earliest possible date of a 747 nacelle core cowl structure. The second program seeks to firmly establish the producibility and cost of a 757 thrust reverser C duct in a production environment. The near term objectives of these programs include: (1) the comparison of estimated cost and weight of Gr/PMR-15 versus metal structure, (2) the engine test of representative composite structure, (3) the preliminary design and analysis of the C duct structure, and (4) the preparation of cost data and time schedules for the development and producibility program. In addition to powerplant structure, the propulsion ducting system has shown to be a strong candidate for Gr/PMR-15 application. Currently, the Boeing 747 Organization is evaluating the use of PMR-15 matrix composites to replace nearly 800 lbs of titanium ducting per airplane.

Postlewaite, J.↗
NASA NTRS1986

Delamination growth in composite materials

The Double Cantilever Beam (DCB) and the End Notched Flexure (ENF) specimens are employed to characterize MODE I and MODE II interlaminar fracture resistance of graphite/epoxy (CYCOM 982) and graphite/PEEK (APC2) composites. Sizing of test specimen geometries to achieve crack growth in the linear elastic regime is presented. Data reduction schemes based upon beam theory are derived for the ENF specimen and include the effects of shear deformation and friction between crack surfaces on compliance, C, and strain energy release rate, G sub II. Finite element (FE) analyses of the ENF geometry including the contact problem with friction are presented to assess the accuracy of beam theory expressions for C and G sub II. Virtual crack closure techniques verify that the ENF specimen is a pure Mode II test. Beam theory expressions are shown to be conservative by 20 to 40 percent for typical unidirectional test specimen geometries. A FE parametric study investigating the influence of delamination length and depth, span, thickness and material properties on G sub II is presented. Mode I and II interlaminar fracture test results are presented. Important experimental parameters are isolated, such as precracking techniques, rate effects, and nonlinear load-deflection response. It is found that subcritical crack growth and inelastic materials behavior, responsible for the observed nonlinearities, are highly rate-dependent phenomena with high rates generally leading to linear elastic response.

Gillespie, J. W., Jr.↗
NASA NTRS1983

Critical joints in large composite aircraft structure

A program was conducted at Douglas Aircraft Company to develop the technology for critical structural joints of composite wing structure that meets design requirements for a 1990 commercial transport aircraft. The prime objective of the program was to demonstrate the ability to reliably predict the strength of large bolted composite joints. Ancillary testing of 180 specimens generated data on strength and load-deflection characteristics which provided input to the joint analysis. Load-sharing between fasteners in multirow bolted joints was computed by the nonlinear analysis program A4EJ. This program was used to predict strengths of 20 additional large subcomponents representing strips from a wing root chordwise splice. In most cases, the predictions were accurate to within a few percent of the test results. In some cases, the observed mode of failure was different than anticipated. The highlight of the subcomponent testing was the consistent ability to achieve gross-section failure strains close to 0.005. That represents a considerable improvement over the state of the art.

Nelson, W. D.↗
NASA NTRS1987

Optical strain measuring techniques for high temperature tensile testing

A number of optical techniques used for the analysis of in-plane displacements or strains are reviewed. The application would be for the high temperature, approximately 1430 C (2600 F), tensile testing of ceramic composites in an oxidizing atmosphere. General descriptions of the various techniques and specifics such as gauge lengths and sensitivities are noted. Also, possible problems with the use of each method in the given application are discussed.

Gyekenyesi, John Z.↗
NASA NTRS1986

The application of cast SiC/Al to rotary engine components

A silicon carbide reinforced aluminum (SiC/Al) material fabricated by Dural Aluminum Composites Corporation was tested for various components of rotary engines. Properties investigated included hardness, high temperature strength, wear resistance, fatigue resistance, thermal conductivity, and expansion. SiC/Al appears to be a viable candidate for cast rotors, and may be applicable to other components, primarily housings.

Stoller, H. M.↗
NASA NTRS1991

Overview of European and other non-US/USSR/Japan launch vehicle and propulsion technology programs

The following subject areas are covered: majority of propulsion technology development work is directly related to the ESA's Ariane 5 program and heavily involves SEP (Societe Europeenne de Propulsion) in all areas; Hermes; advanced work on magnetic bearings for turbomachinery; electric propulsion using Cs and Xe propellants done by SEP in France, MBB ERNO in West Germany, and by Culham Lab in UK; successfully tested fired H/O composite nozzle exit cone on 3rd stage of Ariane; turbine blades made of composites to allow increase in gas temperature and improvement in efficiency; combined cycle (turboramjet-rocket) engine analysis work done by Hyperspace; and ESA advanced program studies.

Rice, Eric E.↗