Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel performance analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

Effects of fuel type and equivalence ratios on the flickering of triple flames

An experimental study has been conducted in axisymmetric, co-flowing triple flames with different equivalence ratios of the inner and outer reactant streams (2<{phi}{sub in}<3 and 0{<=}{phi}{sub out}<0.7). Different fuel combinations, like propane/propane, propane/methane or methane/methane in the inner and outer streams respectively, have been used in the experiments. The structures of the triple flames have been compared for the different fuel combinations and equivalence ratios. The conditions under which triple flames exhibit oscillation have been identified. During the oscillation, the non-premixed flame and the outer lean premixed flame flicker strongly, while the inner rich premixed flame remains more or less stable. The flickering frequency has been evaluated through image processing and fast Fourier transform (FFT) of the average pixel intensity of the image frames. It is observed that, for all the fuel combinations, the frequency decreases with the increase in the outer equivalence ratio, while it is relatively invariant with the change in the inner equivalence ratio. However, an increase in the inner equivalence ratio affects the structure of the flame by increasing the heights of the inner premixed flame and non-premixed flame and also enlarges the yellow soot-laden zone at the tip of the inner flame. A scaling analysis of the oscillating flames has been performed based on the measured parameters, which show a variation of Strouhal number (St) with Richardson number (Ri) as St {proportional_to} Ri{sup 0.5}. The fuel type is found to have no influence on this correlation. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Numerical Investigation of a Central Fuel Property Hypothesis Under Boosted Spark-Ignition Conditions

In the present work, a central fuel property hypothesis (CFPH), which states that fuel properties are sufficient to provide an indication of a fuel’s performance irrespective of its chemical composition, was numerically investigated. In particular, the objective of the study was to determine whether Research Octane Number (RON) and Motor Octane Number (MON), as fuel properties, are sufficient to describe a fuel’s knock-limited performance under boosted spark-ignition (SI) conditions within the framework of CFPH. To this end, four TPRF-bioblendstock surrogates having different compositions but matched RON (=98) and MON (=90), were first generated using a non-linear regression model based on artificial neural network (ANN). Additionally, three unconventional bioblendstocks were included in the analysis: di-isobutylene (DIB), isobutanol, and Anisole. Skeletal reaction mechanisms were generated for the TPRF-DIB, TPRF-isobutanol, and TPRF-anisole blends from a detailed kinetic mechanism. Thereafter, numerical simulations were performed for the fuel surrogates using the skeletal mechanisms and a virtual cooperative fuel research (CFR) engine model, under a representative boosted operating condition. In the computational fluid dynamics (CFD) model, the G-equation approach was employed to track the turbulent flame front and the well-stirred reactor model combined with the multi-zone binning strategy was used to capture auto-ignition in the end-gas. In addition, laminar flame speed (LFS) was tabulated for each blend as a function of pressure, temperature, and equivalence ratio a priori, and the lookup tables were used to prescribe laminar flame speed as an input to the G-equation model. Parametric spark timing sweeps were performed for each fuel blend to determine the corresponding knock-limited spark advance (KLSA) and 50% burn point (CA50) at the respective KLSA timing. It was observed that despite same RON, MON, and engine operating conditions, the TPRF-anisole blend exhibited markedly different knock-limited performance from the other three blends. This deviation from the octane index (OI) expectation was shown to be caused by differences in laminar flame speed. However, it was found that relatively large fuel-specific differences in LFS (>20%) would have to be present to cause any appreciable deviation from the OI framework. Otherwise, RON and MON would still be robust enough to predict a fuel’s knock-limited performance.

42 ENGINEERING↗

AGR-1 Data Qualification Report

ABSTRACT Projects for the very high temperature reactor (VHTR) Technology Development Office (TDO) program provide data in support of Nuclear Regulatory Commission licensing of the VHTR. Fuel and materials to be used in the reactor are tested and characterized to quantify performance in high temperature and high fluence environments. The VHTR program has established the NGNP Data Management and Analysis System (NDMAS) to ensure that VHTR data are (1) qualified for use, (2) stored in a readily accessible electronic form, and (3) analyzed to extract useful results. This document focuses on the first NDMAS objective. It describes the data streams associated with the first Advanced Gas Reactor experiment (AGR-1), the processing of these data within NDMAS, and reports the qualification status of the data. Data qualification activities within NDMAS for specific types of data are determined by the data qualification category assigned by the data generator. They include: (1) capture testing, to confirm that the data stored within NDMAS are identical to the raw data supplied, (2) accuracy testing, to confirm that the data are an accurate representation of the system or object being measured, and (3) documentation that the data were collected under an NQA-1 or equivalent quality assurance program. The NDMAS database processing and qualification status of the following five data streams is reported in this document: 1. Fuel fabrication data. All data have been processed into the NDMAS database and qualified (1,819 records). 2. Fuel irradiation data. Data from all 13 AGR-1 reactor cycles have been processed into the NDMAS database and tested. Of these, 85% have been qualified and 15% have failed NDMAS accuracy testing. 3. FPMS data. Reprocessed (January 2010) data from all 13 AGR-1 reactor cycles have been processed into the database and capture tested. Final qualification of these data will be recorded after QA approval of an Engineering Calculations and Analysis Report currently in review. 4. ATR Operating Conditions Data. Data for all AGR-1 cycles have been stored and capture tested. These data, which come from outside the VHTR program, are assumed to be qualified by ATR quality control procedures. 5. Neutronics and Thermal Modeling Data. NDMAS processing is in progress. These data will not be qualified by NDMAS.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Methodology and Determination of Field of View of Neutron and Gamma Detectors in the Atucha Spent Fuel Storage Pool

In this paper we seek to create a model by determining the field of view (FOV) of a detector (i.e. which assemblies contribute to the detector response) in the Atucha-I spent fuel pool. The FOV is determined by solving the adjoint transport equation using the 3-D, parallel PENTRAN (Parallel Environment Neutral-particle TRANsport) Sn code, with the detector cross section as the adjoint source. If this adjoint function is coupled with the source spectrum, then the contribution to the detector from each assembly can be determined. First, the reactor criticality was modeled using the MCNP5 (Monte Carlo N-Particle) Monte Carlo code in order to determine the power distribution in each assembly. Using the power distribution data, the assemblies were divided and homogenized into 8 axial and 3 radial zones for burnup analysis. Depletion calculations were performed for each zone using the ORIGEN-ARP (Automatic Rapid Processing) utility from the SCALE 5.1 (Standardized Computer Analyses for Licensing Evaluation) code package. Spent fuel pool and detector were modeled in 2-D in PENTRAN as the detector plus 3 fuel assemblies along both x and y axes. Using the resulting adjoint function combined with the source spectrum, they have determined the FOVs of the fission chamber neutron detector that was used at Atucha, and concluded that 2 assemblies along x and y axes are needed for both cases (i.e. the 4 adjacent assemblies plus the next surrounding 12). For the neutron detector, 88% of the response comes from the nearest 4 assemblies, with 99% from the nearest 16. Results for a uniformly sensitive gamma detector indicate that 2 assemblies in both directions are also needed, with 89% of the response coming from the adjacent assemblies. A Monte Carlo calculation using MCNP was performed to benchmark the neutron result, giving a similar result (87% MCNP vs. 88% PENTRAN). Based on these studies, we have developed a database of FOVs as a function of burnup and decay conditions for different detector types, and a methodology/algorithm which uses this database to analyze the response of a detector placed in a spent fuel pool with the aim of detecting gross defects.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Open-Hole Testing of Resin Infused Carbon Composite Laminates to Facilitate Damage Growth and Failure Analysis Tools for Structural Design

In manufacturing of carbon-fiber reinforced composite aircraft structures, resin infusion offers a highly repeatable process for manufacturing structural components with resin content control, low labor requirements, and complex curvatures. To further understand the structural capabilities of res-in infused composites (RIC), this study – as part of the NASA-led Hi-Rate Composite Aircraft Manufacturing project efforts – performed open hole tension (OHT) and open hole compression (OHC) testing on RIC laminates. This testing provides information on the damage morphology and growth characteristics of RICs, which fuels the development and evaluation of analysis tools for progressive damage growth and failure responses. X-ray computed tomography (XCT) was implemented on each OHC and OHT specimen prior to mechanical testing to identify preexisting damage and/or defects. Two OHT and OHC specimens were loaded monotonically to failure and an additional OHT and OHC specimen were loaded intermittently at defined conditions and XCT scanned after each run. From the data obtained in this study, damage mechanisms leading to failure were identified, damage morphology and size were assessed, and damage initiation and failure loads were measured.

HiCAM↗

Study of Jet-Propulsion System Comprising Blower, Burner, and Nozzle

A study was made of the performance of a jet-propulsion system composed of an engine-driven blower, a combustion chamber, and a discharge nozzle. A simplified analysis is made of this system for the purpose of showing in concise form the effect of the important design variables and operating conditions on jet thrust, thrust horsepower, and fuel consumption. Curves are presented that permit a rapid evaluation of the performance of this system for a range of operating conditions. The performance for an illustrative case of a power plant of the type under consideration id discussed in detail. It is shown that for a given airplane velocity the jet thrust horsepower depends mainly on the blower power and the amount of fuel burned in the jet; the higher the thrust horsepower is for a given blower power, the higher the fuel consumption per thrust horsepower. Within limits the amount of air pumped has only a secondary effect on the thrust horsepower and efficiency. A lower limit on air flow for a given fuel flow occurs where the combustion-chamber temperature becomes excessive on the basis of the strength of the structure. As the air-flow rate is increased, an upper limit is reached where, for a given blower power, fuel-flow rate, and combustion-chamber size, further increase in air flow causes a decrease in power and efficiency. This decrease in power is caused by excessive velocity through the combustion chamber, attended by an excessive pressure drop caused by momentum changes occurring during combustion.

FUEL CONSUMPTION↗

Effect of hydrophilic treatment of microporous layer on fuel cell performance

The gas diffusion layer in a polymer electrolyte fuel cell is the component primarily responsible for effective water management under a wide variety of conditions. The incorporation of hydrophilic alumosilicate fibers in the microporous layer leads to an improvement in the fuel cell performance associated with a decrease in the mass transport resistance especially under high RH operation. This improvement in performance is obtained without sacrificing performance under low RH conditions. The alumosilicate fibers create domains that wick liquid water away from the catalyst layer. The improved mass transport performance is corroborated by AC impedance and neutron radiography analysis and is consistent with an increase in the average pore diameter inside the microporous layer.

30 DIRECT ENERGY CONVERSION↗

Nuclear data uncertainty and sensitivity analysis of the VHTRC benchmark using SCALE

The Very High Temperature Critical Assembly (VHTRC) experiment represents one of the few data sets available for the validation of HTGR lattice physics. Within the framework of the IAEA Coordinated Research Project on HTGR Uncertainty Analysis in Modeling, uncertainty and sensitivity analyses of this graphite-moderated facility are performed as the validation reference to the prismatic MHTGR-350 fuel block calculations. Nominal multi-group and continuous-energy criticality calculations with the KENO-VI Monte Carlo code of the SCALE code package are compared with the continuous-energy Monte Carlo Code Serpent. Good agreement with a maximum difference of 250 pcm is obtained. The experimental data set, however, differs by several hundred pcm with the results of both codes when using the ENDF-VII.0 library. When using ENDF/B-VII.1 data, this difference is reduced to a few hundred pcm and the calculations lie within the experimental error bars. Uncertainties of the VHTRC multiplication factors due to uncertainties in nuclear data are determined with SAMPLER/KENO-VI of SCALE 6.2 and with continuous-energy TSUNAMI of SCALE 6.2. For all experimental configurations, the obtained uncertainty is found to be 0.58% when using ENDF/B-VII.0 data. The top contributor to this uncertainty is the average number of neutrons per fission event of U-235. With ENDF/B-VII.1 data, uncertainties of about 0.66% are obtained in particular due to an increased uncertainty of U-235 nu-bar in the latest ENDF release. In conclusion, when considering these nuclear data uncertainties, the obtained 1s uncertainty intervals are overlapping with the experimental error bars.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Colloidal Nafion Particles: Are Cylinders Ubiquitous?

Colloidal Nafion morphology plays a critical role in determining the performance of fuel cells and electrolyzers. While small-angle neutron scattering (SANS) studies previously described Nafion in liquid media as dispersed cylinders, the analysis remains nonunique with multiple possible morphological descriptions of the data. Here, using SANS and all-atomistic molecular dynamics, we confirm that Nafion morphology in liquid media differs substantially depending on dispersing agent and dispersion method. H + Nafion dispersed in N-methyl pyrrolidone forms swollen cluster particles with physically cross-linked ionic groups. Scattering profiles from dispersed Nafion membrane have a large structure factor feature not observed for redispersed Nafion D-521. H + Nafion dispersed in water has a highly elongated cylindrical morphology (radius = 10 ± 1.5 Å, height = 358 ± 4.7 Å) with fully dissociated and solvated sulfonic acid groups on the particle wall. In conclusion, these results highlight an important discrepancy between the methods of preparing Nafion dispersions and the use of simplified analysis techniques to describe Nafion morphology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Technoeconomic Design Optimization for Fast Reactors. Part I: Workflow Development and Case Study for Small LFR District Energy Application

The nuclear industry is developing small reactor designs that can target a variety of deployment locations and energy products. Smaller nuclear designs have traditionally struggled to handle the steep trade-offs between size and cost that have historically incentivized large reactors. This motivates computational optimization of small reactors to minimize costs and quantify the trade-off between size and cost. In this paper, the cost/size trade-off for a small fast reactor is derived using a multi-objective genetic algorithm optimization, with steady-state, transient, and cost analysis of the fast reactor being performed. Specifically, the method is demonstrated on a small 10- to 120-MW(thermal) U-Pu-Zr–fueled lead-cooled fast reactor with a 10-year core life for district energy applications, which can have a thermal load compatible with this range. The results reinforced that fast reactor cores at the lower end of this power range suffer cost penalties due to critical mass considerations. It was found that high power density cores with strong reactivity swings and many control rods were favored over designing to minimize reactivity swing. Furthermore, this contrasts with some traditional configurations designed using engineering judgment and demonstrates that optimizers can find nontraditional but realistic solutions, along with demonstrating the value of incorporating cost functions into whole-reactor design optimization.

Fast reactor↗

Analysis of Two-Dimensional Lattice Physics Verification Problems with MPACT

CASL is developing the Virtual Environment for Reactor Applications (VERA) as a key capability to support the analysis of the CASL Challenge Problems. VERA will include a range of physics modeling capabilities necessary to model reactors, including neutronics, thermal hydraulics, fuel performance, coolant chemistry, with development efforts underway in all of these areas. This report documents the application of the lattice physics capability available in MPACT v1.0.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Design of multihundred-watt dynamic isotope power system for robotic space missions

The design of a multihundred-watt dynamic isotope power system (DIPS) based on the US Department of Energy (DOE) general-purpose heat source (GPHS) and small (multihundred-watt) free-piston Stirling engine (FPSE) is described as a potential lower cost alternative to radioisotope thermoelectric generators (RTGs). The design is targeted at the power needs of future unmanned deep space and planetary surface exploration missions. Since the competitive potential of FPSE as an isotope convertor was first identified, work has focused on the feasibility of directly integrating GPHS with the Stirling heater head. Thermal modeling of various radiatively coupled heat source/heater head geometries has been performed using data furnished by the developers of FPSE and GPHS. The analysis indicates that, for the 1050 K heater head configurations considered, GPHS fuel clad temperatures remain safe operating limits under all conditions including shutdown of one engine on a twin engine unit. Based on these results, preliminary characterizations of multihundred-watt units have been established. They indicate that, per electrical watt, the GPHS/small Stirling DIPS will be roughly equivalent to MOD RTG in size and mass but will require about a third the amount of isotope fuel.

Bents, D. J.↗

Hypersonic vehicle control law development using H(infinity) and micron-synthesis

Hypersonic vehicle control law development using H(infinity) and mu-synthesis is discussed. Airbreathing SSTO vehicles has a mutli-faceted mission that includes orbital operations, as well as re-entry and descent culminating in horizontal landing. However, the most challenging part of the operations is the ascent to orbit. The airbreathing propulsion requires lengthy atmospheric flight that may last as long as 30 minutes and take the vehicle half way around the globe. The vehicles's ascent is characterized by tight payload to orbit margins which translate into minimum fuel orbit as the performance criteria. Issues discussed include: SSTO airbreathing vehicle issues; control system performance requirements; robust control law framework; H(infinity) controller frequency analysis; and mu controller frequency analysis.

Gregory, Irene M.↗

Validation of Criticality Safety Calculations with SCALE 6.2

SCALE 6.2 provides numerous updates in nuclear data, nuclear data processing, and computational tools utilized in the criticality safety calculational sequences relative to SCALE 6.1. A new 252-group ENDF/B-VII.0 multigroup neutron library, improved ENDF/B-VII.0 continuous energy data, as well as the previously deployed 238-group ENDF/B-VII.0 neutron library are included in SCALE 6.2 for criticality safety analysis. The performance of all three libraries for keff calculations is examined with a broad sampling of critical experiment models covering a range of fuels and moderators. Critical experiments from the International Handbook of Evaluated Criticality Safety Benchmark Experiments (IHECSBE) that are available in the SCALE Verified, Archived Library of Inputs and Data (VALID) are used in this validation effort. Over 300 cases are used in the validation of KENO V.a, and a more limited set of approximately 50 configurations are used for KENO-VI validation. Additionally, some KENO V.a cases are converted to KENO-VI models so that an equivalent set of experiments can be used to validate both codes. For continuous-energy calculations, SCALE 6.2 provides improved performance relative to SCALE 6.1 in most areas with notable improvements in fuel pin lattice cases, particularly those with mixed oxide fuel. Multigroup calculations with the 252-group library also demonstrate improved performance for fuel lattices, uranium (high and intermediate enrichment) and plutonium metal experiments, and plutonium solution systems. Overall, SCALE 6.2 provides equivalent or smaller biases than SCALE 6.1, and the two versions of KENO provide similar results on the same suite of problems.

97 MATHEMATICS AND COMPUTING↗

Recent research activities on high temperature pebble bed reactors at PSI - 18452

Recently, Paul Scherrer Institut (PSI) commenced a project on Feasibility and plausibility of innovative reactor concepts in an European electricity supply environment. The investigation in the project will be done on two reactor types: the pebble bed High-Temperature Gas-Cooled Reactor (HTGR) and Molten Salt Reactor (MSR) with the main focus being on the HTGR. Firstly, the project consists of an extensive literature study on the current status of the technology and research on the HTGR and MSR. Secondly, based on the findings from the literature survey, several topics of particular interest have been chosen for more thorough investigations. On the pebble bed HTGRs, the areas of investigation include risk assessment study, preliminary economic assessment, investigation of accident scenarios, and preliminary study on reduction of waste volumes. For both HTGR and MSR an analysis and optimization of the fuel cycle is foreseen. At the initial stage the equilibrium closed Th-U and U-Pu cycle performance will be evaluated and compared with 16 other reactor types. Later the knowledge from equilibrium study will be applied to optimize especially the MSR but also HTGR fuel cycle. At the end of the project, based on the literature survey and the results from the scoping studies, future research needs and areas of special interest will be identified for successive projects related to HTGR and MSR in PSI. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Full Integration of the Fission Product Release Module STACY into the HTR Code Package (HCP) - 18661

The HTR Code Package is under development since 2010 at Forschungszentrum Juelich and at Aachen University. The HCP combines the capabilities of individual legacy codes developed during the German HTR program in a highly integrated manner and contains new features. Within the HCP, all aspects related to fission product release and the redistribution within the primary circuit are handled by the module STACY (Source Term Analysis Code system). STACY is the successor of the codes FRESCO-I/II (dealing with fission product release) and PANAMA (dealing with fuel performance issues). Compared to these predecessor codes, STACY can take amongst others a time-dependent nuclide inventory and a radial temperature profile within the fuel element into account. So far, this version of STACY performs an individual fission product release calculation for a representative number of tracer pebbles. While this version of STACY still relies on codes like VSOP and MGT-3D and contains features such as basic fuel management which are also contained in the before mentioned codes, STACY now will be coupled to forms an integral part of the HCP. Thus, fission product release calculations will be examined with one consistent reactor input model. This allows assessing the release of fission products already during the design phase, besides parameters like the maximum fuel temperature during a transient. Furthermore the total nuclide inventory of a fuel element is distributed among fuel kernels, coating layers, graphite grains and pores of the surrounding matrix graphite. Formerly, this total inventory calculated by the burnup code TNT was distributed according to the distribution of Uranium. As a new feature, STACY now keeps track of the distributions of nuclide inventories within the fuel element. Especially for nuclides mainly formed by activation and decay processes like Ag-110m, this approach is more accurate. Further, the knowledge about the actual nuclide inventories improves the accuracy of fuel performance calculations. In addition, the internal coupling allows a feedback from the fission product calculation to other code modules. Nuclides amounts being released can be considered in e.g. the burnup calculation while calculating the source term of for example tritium or within the calculation which takes care of the redistribution of species by the coolant. Within this paper, the application of the STACY to HTR cores with special emphasis on fission product release to reactor models such as the HTR-Modul and HTR-10 will be discussed. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Ethanol to diesel: a sustainable alternative for the heavy-duty transportation sector

The combustion of middle distillates (diesel and jet fuel) is responsible for the emission of more than 2 GTon of CO 2 per year worldwide. While sustainable alternatives exist for gasoline and jet fuel, we still lack sustainable alternatives for diesel. This fact is especially relevant if we consider that electrification of sectors where diesel is used is challenging. One sustainable approach for diesel production is the catalytic upgrading of ethanol. While most work in this field has focused on the dehydration/oligomerization of ethanol, this approach is limited to producing fuels that have a high degree of branching and low cetane number. Another approach is the sequential use of ethanol Guerbet coupling, leading to higher alcohols, followed by etherification, leading to large ethers which, importantly, result in a product with high cetane number. In this work, we explore the catalytic upgrading of ethanol into diesel following an approach based on the initial Guerbet coupling of ethanol followed by etherification. The results presented are a collaborative and synergic effort among process and systems engineers, experimentalist in the area of catalysis, and fuel property modelers. Here, we demonstrate experimentally the feasibility of upgrading ethanol into a diesel fuel with properties that surpass its fossil counterpart. The diesel produced has a predicted cetane number of ~70 and outstanding cold flow properties, while maintaining other properties (viscosity, density, and flash point) within expected ranges. A technoeconomic analysis performed based on a detailed biorefinery model shows that the MFSP is ~5.89$ per Gal in 2021 dollars when lignocellulosic ethanol is used, with the most relevant economic driver the cost of the ethanol feedstock. The upgrading process can be performed with a net energy gain (EROI = 1.49 > 1). An LCA analysis of greenhouse gas (GHG) emissions reveals that the use of lignocellulosic ethanol may lead to more than 50% reduction in GHG emissions compared to fossil diesel. Depending on the CO 2 emissions associated with the production of ethanol we show that in some instances the production of carbon neutral diesel fuel is possible.

09 BIOMASS FUELS↗

Low-Moisture Switchgrass Bulk-Format Logistics Costs Based on Engineering Data

Abstract. Logistics costs that spanned harvest, transport, storage, preprocessing, and year-round delivery of 371,870 dMg year -1 of milled, low-moisture switchgrass (SG) to a local biorefinery were determined for bulk-format versus round-bale systems. Separate spreadsheet analyses were conducted for three diesel fuel prices ($0.53 L -1 , $0.92 L -1 , and $1.32 L -1 ) because of the wide range of fuel prices during the project. A detailed analysis scenario identified a common harvest period, equipment annual use, other equipment uses, and protected SG storage on gravel pad, along with equipment performances based on previously published tests primarily for commercially available equipment. The bulk-format system used a depot equipped with stacker/reclaimer technology for storage, whereas the round-bale system used field-side bale stacks for storage, with both systems assuming 6% losses, primarily attributed to storage. Results indicated total costs for bulk-format versus round-bale systems of $54.63 per dry Mg (dMg -1 ), $60.41 dMg -1 , and $66.21 dMg -1 versus $54.59 dMg -1 , $62.10 dMg -1 , and $67.93 dMg -1 corresponding with diesel fuel costs of $0.53 L -1 , $0.92 L -1 , and $1.32 L -1 , respectively. The most significant bulk-format system total cost of $22.79 dMg -1 was associated with a stacker/reclaimer, conveyance, and dust collection at the depot, which was 42% of total costs at a diesel fuel cost of $0.53 L -1 . For the round-bale system, bale chopping total costs was highest and represented an average of 27% of total costs, with costs ranging from $14.63 dMg -1 to $19.08 dMg -1 for diesel fuel input costs ranging from $0.53 L -1 to $1.32 L -1 , respectively. For comparison, the forage harvester provided harvesting and chopping in the bulk-format system at total costs ranging from $6.47 dMg -1 to $8.80 dMg -1 across the same range of diesel fuel input cost. The forage harvester provided an economic advantage in size reduction compared to tub grinding. Truck hauling for both the bulk-format and round-bale systems represented significant expenses at all selected fuel costs. In addition, the multiple times that round bales were handled represented accumulating costs that were sensitive to diesel fuel costs. Keywords: Bales, Bioenergy, Bulk format, Densification, Field chop, Logistics, Transportation.

Agriculture↗