Search NASA⌕ Search

SEARCH · Search NASA

Results for “Injection testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Testing of Face-milled Spiral Bevel Gears at High-speed and Load

Spiral bevel gears are an important drive system components of rotorcraft (helicopters) currently in use. In this application the spiral bevel gears are required to transmit very high torque at high rotational speed. Available experimental data on the operational characteristics for thermal and structural behavior is relatively small in comparison to that found for parallel axis gears. An ongoing test program has been in place at NASA Glenn Research Center over the last ten years to investigate their operational behavior at operating conditions found in aerospace applications. This paper will summarize the results of the tests conducted on face-milled spiral bevel gears. The data from the pinion member (temperature and stress) were taken at conditions from slow-roll to 14400 rpm and up to 537 kW (720 hp). The results have shown that operating temperature is affected by the location of the lubricating jet with respect to the point it is injected and the operating conditions that are imposed. Also the stress measured from slow-roll to very high rotational speed, at various torque levels, indicated little dynamic affect over the rotational speeds tested.

Handschuh, Robert F.↗
NASA NTRS2001

Testing of Face-milled Spiral Bevel Gears at High-speed and Load

Spiral bevel gears are an important drive system components of rotorcraft (helicopters) currently in use. In this application the spiral bevel gears are required to transmit very high torque at high rotational speed. Available experimental data on the operational characteristics for thermal and structural behavior is relatively small in comparison to that found for parallel axis gears. An ongoing test program has been in place at NASA Glenn Research Center over the last ten years to investigate their operational behavior at operating conditions found in aerospace applications. This paper will summarize the results of the tests conducted on face-milled spiral bevel gears. The data from the pinion member (temperature and stress) were taken at conditions from slow-roll to 14400 rpm and up to 537 kW (720 hp). The results have shown that operating temperature is affected by the location of the lubricating jet with respect to the point it is injected and the operating conditions that are imposed. Also the stress measured from slow-roll to very high rotational speed, at various torque levels, indicated little dynamic affect over the rotational speeds tested.

Handschuh, Robert F.↗
NASA NTRS2002

Testing of Face-Milled Spiral Bevel Gears at High-Speed and Load

Spiral bevel gears are important drive system components of rotorcraft (helicopters) currently in use. In this application the spiral bevel gears are required to transmit very high torque at high rotational speed. Available experimental data on the operational characteristics for thermal and structural behavior is relatively small in comparison to that found for parallel axis gears. An ongoing test program has been in place at NASA Glenn Research Center over the last ten years to investigate their operational behavior at operating conditions found in aerospace applications. This paper will summarize the results of the tests conducted on face-milled spiral bevel gears. The data from the pinion member (temperature and stress) were taken at conditions from slow-roll to 14400 rpm and up to 537 kW (720 hp). The results have shown that operating temperature is affected by the location of the lubricating jet with respect to the point it is injected and the operating conditions that are imposed. Also the stress measured from slow-roll to very high rotational speed, at various torque levels, indicated little dynamic affect over the rotational speeds tested.

Handschuch, Robert F.↗
NASA NTRS2015

NOx Emissions Performance and Correlation Equations for a Multipoint LDI Injector

Lean Direct Injection (LDI) is a combustor concept that reduces nitrogen oxides (NOx) emissions. This paper looks at a 3-zone multipoint LDI concept developed by Parker Hannifin Corporation. The concept was tested in a flame-tube test facility at NASA Glenn Research Center. Due to test facility limitations, such as inlet air temperature and pressure, the flame-tube test was not able to cover the full set of engine operation conditions. Three NOx correlation equations were developed based on assessing NOx emissions dependencies on inlet air pressure (P3), inlet air temperature (T3), and fuel air equivalence ratio (Ф) to estimate the NOx emissions at the unreachable high engine power conditions. As the results, the NOx emissions are found to be a strong function of combustion inlet air temperature and fuel air equivalence ratio but a weaker function of inlet air pressure. With these three equations, the NOx emissions performance of this injector concept is calculated as a 66% reduction relative to the ICAO CAEP-6 standard using a 55:1 pressure-ratio engine cycle. Uncertainty in the NOx emissions estimation increases as the extrapolation range departs from the experimental conditions. Since maximum inlet air pressure tested was less than 50% of the full power engine inlet air pressure, a future experiment at higher inlet air pressure conditions is needed to confirm the NOx emissions dependency on inlet air pressure.

NOx correlation equations↗
NASA NTRS2017

GEER Status Update

History: The Glenn Extreme Environments Rig (GEER) first became operational in the early part of 2015. Since that time GEER has completed a number of scientific tests and has undergone improvements in the chemical delivery system and analytics following a year of operations experience. Recent Updates: In June 2016, the GEER process system was rebuilt to provide a more robust system, higher accuracy and new capabilities. New insulation was installed on the exterior of the pressure vessel and gas lines. The newly revamped GEER plumbing system can provide extremely precise custom gas mixtures using any gas desired by the investigator in any combination. GEER can heat the resulting mixture up to 500 deg C and 1500 psia. The 304 stainless steel vessel walls were polished to reduce corrosion rate and reduce unwanted chemical reactions. The process lines were replaced with high purity Sulfinert coated tubing. The GEER team added the ability to individually boost specialty gases to GEER thus allowing operators to make very precise changes to the gas chemistry inside of GEER during a test while at high temperature and pressure. High accuracy mass flow meters were added to further improve gas mixing accuracy and precision. An in-line, integrated Inficon MicroGC Fusion was added for real time gas analysis along with a high purity gas sampling system, providing fully automated, real time analysis of the gas chemistry inside of GEER in minutes. This complements a co-located mass spectrometer and both are used for regular monitoring of the vessel chemistry. All internal vessel components were replaced with polished 304SS equivalents. Hot vent down capability was increased. Finally, an automated liquid injection system was added and is rated for max vessel operating conditions of (1500 psia, 500 C). Recent Results and Publications: In May 2016, GEER completed a test that exposed high temperature electronics to Venus surface conditions for 21.5 days. This demonstrated the potential for operating robotic spacecraft in the Venus environment without the need for thermal or environmental protection. Results from this test were published in December 2016 and received national media attention. In April 2017 GEER implemented an 80 day test at Venus surface conditions to simulate chemical weathering of expected Venus minerals. This test supported a ROSES award to a team led by Prof. Ralph Harvey of Case Western Reserve University. The test concluded in July 2017 and nearly doubled previous operation record of 42 days at Venus surface conditions. Preliminary results of these and previous experiments were presented at the recent Venus Modeling Workshop. In June 2017, NASA TM2017-219437 "Chemical and Microstructural Changes in Metallic and Ceramic Materials Exposed to Venusian Surface Conditions" was published. This report provides an extensive and valuable resource detailing the behavior of a variety of engineering materials at Venus surface conditions. Community Involvement: An external science advisory panel has been formed.

Kremic, Tibor↗
DOE OSTI2022

Advanced Thin Film Core Technology: CIGS Final Technical Report (FTR)

Cu(In,Ga)Se 2 (CIGS) thin-film photovoltaics are a high-efficiency and reliable technology. This project completed research in two important areas and was designed to work collaboratively with industrial partners. Task 1: Alkali Science focused on alkali post-deposition treatments (PDT). PDTs have been instrumental in the dramatic voltage improvements that have moved CIGS device efficiencies from 20% to 23.35% [1]. Based on a survey of CIGS companies at the beginning of the project, the single biggest breakthrough for the CIGS community would be a mechanistic understanding of the role of alkalis in the material system. Significant accomplishments of Task 1: Alkali Science: 1) KF post-deposition treatments were shown to improve lifetime, open-circuit voltage (VOC), and efficiency of industrial partner samples, even when done as a later step, separate from the original CIGS deposition. 2) KF boosted efficiency when incorporated at the end of the third stage of NREL CIGS growth. 3) XPS characterization of CIGS surfaces with and without PDTs led to a proposed mechanism whereby K drives structural transformation at 350 degrees C that is locked in at room temperature even after K is rinsed away. 4) Published recipes for KF and RbF PDTs. Literature to date did not provide enough detail to quickly reproduce experimental results. 5) Identified most important parameters (RbF cell temperature and lamp setpoint temperature) and set boundaries for successful RbF PDTs. The purpose of Task 2: Cell-level Reliability was to overcome the largest challenges to investor confidence and long product lifetime in CIGS-based photovoltaic products: metastability, shading-induced hot spots, and potential-induced degradation (PID). Key findings were made in each of these areas by studying CIGS reliability at the cell level: 1) Published NREL's cell-level reliability testing procedures along with challenges that were encountered while developing them. These were also distributed to the community through an MRS conference presentation. 2) Decreased metastability by adding a CdS hole-injection layer between the CIGS and Zn(O,S) in the device stack. It also improved device performance. Materials other than CdS can be used for the same purpose. 3) Reduced front-glass PID by replacing soda-lime glass with low-Na borosilicate glass. 4) Found that PID depends on leakage current and light/electrical bias. This will help labs avoid test-specific degradation. 5) Discovered that CIGS can suffer from two different types of PID with different mechanisms. Front is slower and leads to shunting ZnO. Back is faster and degrades the p-n junction. 6) Holding cells at open circuit slows PID compared to short circuit. This affects testing protocols for glass/glass modules.

14 SOLAR ENERGY↗
NASA NTRS1976

Fluid dynamic research at NASA-Ames Research Center related to transonic wind tunnel design and testing techniques

Fluid dynamic research with the objective of developing new and improved technology in both test facility concepts and test techniques is being reported. A summary of efforts and results thus far obtained in four areas is presented. The four area are: (1) the use of heavy gases to obtain high Reynolds numbers at transonic speeds: (2) high Reynolds number tests of the C-141A wing configuration; (3) performance and flow quality of the pilot injector driven wind tunnel; and (4) integration time required to extract accurate static and dynamic data from tests in transonic wind tunnels. Some of the principal conclusions relative to each of the four areas are: (1) Initial attempts to apply analytical corrections to test results using gases with gamma other than 1.4 to simulate conditions in air show promise but need significant improvement; (2) for the C-141A configuration, no Reynolds number less than the full scale flight value provides an accurate simulation of the full scale flow; (3) high ratios of tunnel mass flow rate to injection mass flow rate and high flow quality can be obtained in an injector driven transonic wind tunnel; and (4) integration times of 0.5 to 1.0 sec may be required for static force and pressure tests, respectively, at some transonic test conditions in order to obtain the required data accuracy.

Muhlstein, L., Jr.↗
NASA NTRS1992

The effect of entrance radius and film injection on wall heating in scramjet nozzles

An experimental study has been performed with a scramjet combustor and nozzle model to determine the effect of nozzle radii on relaminarization, and the effectiveness of film injection in reducing wall heat flux. The nozzle model was installed downstream of a swept-ramp scramjet combustor model, operated at Mach 2.7 with vitiated air, simulating Mach 6-7 flight enthalpies. Results from tests conducted with three nozzle radii, varying in curvature from a sharp Prandtl-Meyer expansion to a radius of two scramjet combustor exit heights, showed little or no effect on the downstream wall heat flux, which is not in agreement with both subsonic and supersonic relaminarization correlations in the available literature. In contrast, film injection upstream of all three radii produced reductions of 70 percent in the entire nozzle model heating rate, for the nominal film-to-free stream pressure matched condition. Results from film injection, with and without pressure gradient, but without wall curvature, show that the gradients appear to stabilize the film, with the resulting reductions in wall heat transfer rates apparent far downstream of the point of injection.

Baker, N. R.↗
NASA NTRS1993

STE thrust chamber technology: Main injector technology program and nozzle Advanced Development Program (ADP)

The purpose of the STME Main Injector Program was to enhance the technology base for the large-scale main injector-combustor system of oxygen-hydrogen booster engines in the areas of combustion efficiency, chamber heating rates, and combustion stability. The initial task of the Main Injector Program, focused on analysis and theoretical predictions using existing models, was complemented by the design, fabrication, and test at MSFC of a subscale calorimetric, 40,000-pound thrust class, axisymmetric thrust chamber operating at approximately 2,250 psi and a 7:1 expansion ratio. Test results were used to further define combustion stability bounds, combustion efficiency, and heating rates using a large injector scale similar to the Pratt & Whitney (P&W) STME main injector design configuration including the tangential entry swirl coaxial injection elements. The subscale combustion data was used to verify and refine analytical modeling simulation and extend the database range to guide the design of the large-scale system main injector. The subscale injector design incorporated fuel and oxidizer flow area control features which could be varied; this allowed testing of several design points so that the STME conditions could be bracketed. The subscale injector design also incorporated high-reliability and low-cost fabrication techniques such as a one-piece electrical discharged machined (EDMed) interpropellant plate. Both subscale and large-scale injectors incorporated outer row injector elements with scarfed tip features to allow evaluation of reduced heating rates to the combustion chamber.

Source record↗
NASA NTRS1985

Deposition of Na2SO4 from salt-seeded combustion gases of a high velocity burner rig

With a view to developing simulation criteria for the laboratory testing of high-temperature materials for gas turbine engines, the deposition rates of sodium sulfate from sodium salt-seeded combustion gases were determined experimentally using a well instrumented high-velocity burner. In the experiments, Na2SO4, NaCl, NaNO3, and simulated sea salt solutions were injected into the combustor of the Mach 0.3 burner rig operating at constant fuel/air ratios. The deposits formed on an inert rotating collector were then weighed and analyzed. The experimental results are compared to Rosner's vapor diffusion theory. Some additional test results, including droplet size distribution of an atomized salt spray, are used in interpreting the deposition rate data.

Santoro, G. J.↗
NASA NTRS1973

Multispectral image dissector camera flight test

It was demonstrated that the multispectral image dissector camera is able to provide composite pictures of the earth surface from high altitude overflights. An electronic deflection feature was used to inject the gyro error signal into the camera for correction of aircraft motion.

Johnson, B. L.↗
NASA NTRS1976

Teledyne Continental Motors emissions data and analysis and flight test results

Five different engine models were tested covering combinations of all engine categories in current production in the range from 100 to 435 brake horsepower. Engines were divided into five major types: carbureted, fuel injected, direct drive, geared, and turbocharged. Emissions data were categorized by three separate fuel system schedules: baseline, case 1, and case 2. Baseline was defined as the average fuel flow rate established by the fuel system's production tolerance band when operated with the mixture control at the full-rich position. Case 1 was defined as the minimum allowable fuel flow rate established by the engine certification. Case 2 was defined as the fuel rate corresponding to the leanest fuel-air ratio obtainable before a safety limit occurred with the engine operating on a propeller test stand. Safety limits that developed during testing were cylinder-head overheating or inadequate acceleration from a given mode of operation.

Rezy, B. J.↗
DOE OSTI2023

Polarized fusion and potential in situ tests of fuel polarization survival in a tokamak plasma

Abstract The use of spin-polarized fusion fuels would provide a significant boost towards the ignition of a burning plasma. The cross section for D + T → α + n, would be increased by 1.5 if the fuels were injected with parallel polarization. Furthermore, our simulations demonstrate additional non-linear power gains in large-scale machines such as ITER, due to increased alpha heating. Such benefits require the survival of spin polarizations for periods comparable to the particle confinement time. During the 1980s, calculations predicted that polarizations could survive a plasma environment, although concerns persisted regarding the cumulative impacts of wall recycling. In that era, technical challenges prevented direct tests and left the large scale fueling of a power reactor beyond reach. Over the last decades, this situation has changed dramatically. Detailed simulations of ITER have predicted negligible wall recycling in a high-power reactor, and recent advances in laser-driven sources project the capability of producing large quantities of ∼100% polarized D and T. The remaining crucial step is an in-situ demonstration of polarization survival in a plasma. For this, we outline a measurement strategy using the isospin-mirror reaction, D + 3 He → α + p. Polarized 3 He avoids the complexities of handling tritium, while encompassing the same spin-physics. We evaluate two methods of delivering deuterium, using dynamically polarized Lithium-Deuteride (with vector polarization P V D of 70%) or frozen-spin Hydrogen-Deuteride (with P V D of 40%), together with a method of injecting optically-pumped 3 He (with 65% polarization). Pellets of these materials all have long polarization decay times (∼6 min for LiD at 2 K, ∼2 months for HD at 2 K, and ∼3 d for 3 He at 77 K), all far greater than a plasma shot in a research tokamak such as DIII-D (∼20 s). Both species can be propelled from a single cryogenic injection gun. We review plasma requirements and strategies for detecting polarization survival. Polarization alters both fusion yields and the angular distribution of fusion products, and each of these provides a potential signal. In this paper we simulate a selection of shots with similar characteristics in a future high-T ion H plasma, and find ratios of yields from shots with fuel spins parallel and antiparallel reaching 1.3 (HD + 3 He) to 1.6 (LiD + 3 He) over a wide range of poloidal angles. (A companion paper finds sensitivity to fusion product angular distributions as reflected in the pitch angles of protons and alphas reaching the plasma facing wall.)

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

Advancing Turbulent Spray and Combustion Models for Compression Ignition Engine Simulations

This thesis seeks to investigate the turbulent mixing influence on spray atomization and combustion processes encountered in compression ignition diesel engines. Despite greater thermal efficiency of diesel engine than spark ignition engine, the nature of stratified air-fuel mixture and non-premixed flame gives rise to unacceptable levels of nitrogen oxides (NOx) and particulate matter (PM), thus the use of diesel engines has often been limited to heavy-duty vehicle and industrial power sources. However, recent advancement in diesel engine combustion strategies, e.g. low temperature com-bustion (LTC), has demonstrated promising pathways towards improvement in the engine-out pollutants. Therefore, particularly in the effort of computer-aided en-gine design tasks, such a new engine design concept requires more accurate modeling techniques applicable over a broader range of engine operating conditions than those of conventional engine strategies. In the notion of challenges in new engine operat-ing conditions, this thesis aims to present successful implementation of improvement in numerical modeling techniques in high-pressure spray atomization and resulting turbulent spray flame of interest. Three-dimensional Computational Fluid Dynamics (CFD) in in-cylinder turbu-lent combustion is considered an integral part of engine design progress, but rather a cost-prohibitive to apply over a broad range of engine relevant conditions. In spite of successful use of existing spray atomization modeling, prior researchers have pointed out some degree of failure in LTC targeted injection strategies. Furthermore, finite rate and strong nonlinearity of chemistry influenced by local turbulent mixing still re-main in challenges to account for in cost-efficient CFD analysis. In this context, a new attempt of hybrid spray primary breakup modeling is presented and demonstrated in successful application aimed at LTC technique. In addition, the Representative Interactive Flamelets (RIF) model with aid of multi-flamelets approach is extensively assessed in terms of predictive capability against classical combustion model. The combustion model employed in this study are fully examined in the general diesel combustion metric, e.g., ignition delay and flame lift-off length as well as newly sug-gested test metric, combustion recession. The combustion recession has been recently idenfied, but still remain largely unknown. Since the governing physics of this phe-nomenon is characterized by turbulent mixing coupled with finite rate chemistry, this can be considered as a relevant test metric for turbulent combustion models. In ad-dition, very recent experimental studies have introduced a new non-sooting diesel combustion technique by manipulating direct injection method. The ducted fuel in-jection (DFI) has thus been demonstrated with its potential of low soot emissions. Knowing that the duct equipped ahead of injector nozzle was identifed to enhance turbulent mixing, investigations of DFI combustion may prove the effectiveness of turbulece-chemistry interaction modeling. This thesis presents comprehensive under-standings of aformentioned diesel combustion techniques in terms of several important physics keywords, e.g., turbulent mixing and detailed chemistry

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS2016

A Dual-Plane PIV Study of Turbulent Heat Transfer Flows

Thin film cooling is a widely used technique in turbomachinery and rocket propulsion applications, where cool injection air protects a surface from hot combustion gases. The injected air typically has a different velocity and temperature from the free stream combustion flow, yielding a flow field with high turbulence and large temperature differences. These thin film cooling flows provide a good test case for evaluating computational model prediction capabilities. The goal of this work is to provide a database of flow field measurements for validating computational flow prediction models applied to turbulent heat transfer flows. In this work we describe the application of a Dual-Plane Particle Image Velocimetry (PIV) technique in a thin film cooling wind tunnel facility where the injection air stream velocity and temperatures are varied in order to provide benchmark turbulent heat transfer flow field measurements. The Dual-Plane PIV data collected include all three components of velocity and all three components of vorticity, spanning the width of the tunnel at multiple axial measurement planes.

Turbulent heat transfer↗
DOE OSTI2021

Selective penetration behavior of microgels in superpermeable channels and reservoir matrices

Gel treatment is an effective way to attack excessive water production in many mature oilfields around the world. Selective penetration is desired for successful gel treatments. That is, gel materials should easily penetrate the target zones (i.e., channeling features such as superpermeable channels) without entering/damaging the nontarget zones (i.e., reservoir matrices or oil zones). This study revealed that presence of threshold penetration pressure (ΔP th ) was responsible for selective penetration behavior of tested microgels. The concept of ΔP th was utilized to figure out favorable working conditions for effective gel treatments. Microgel dispersions were injected into superpermeable (super-k) sandpacks (mimicking super-k channels in reservoirs, 60–221 darcies), heterogeneous models with super-k channels (79–230 darcies), and sandstone cores (mimicking reservoir matrices, 50–5000 md). The results demonstrated that a minimum differential driving pressure (i.e., threshold penetration pressure, ΔP th ) was required to push microgel particles to penetrate channels or matrices. The critical penetration behavior was closely related to the particle/pore size ratio. Low ΔP th at smaller particle/pore ratios was beneficial to allow easy penetration of gel materials into the channeling zones. On the contrary, high ΔPth at larger particle/pore ratios was desirable to prevent gel materials from massively invading and damaging the matrices. Instead, the gel particles accumulated at the inlet surface, and a gel cake was gradually formed. The cake further prevented the invasion of the gels. The cake could be removed by chemical breakers to resume the injectivity/productivity of the matrices. Correlations were developed to describe the relationship between ΔP th and particle/pore ratio. A distinct transition was identified at the particle/pore ratio of about 3. This research could help identify the favorable conditions to achieve successful gel treatments. In an effective conformance treatment, the particle/pore ratio in the channel should be sufficiently low to allow easy penetration of gel materials into the channel (e.g., particle/pore ratio<2 in this study). Meanwhile, the particle/pore ratio in the matrix should be large enough to support a high ΔP th and thus prevent massive gel invasion into the matrix. This study advances the current pore scale studies (a single particle passing through a single channel) to Darcy-scale characterization.

02 PETROLEUM↗
DOE OSTI2023

K-RET: knowledgeable biomedical relation extraction system

Abstract Motivation Relation extraction (RE) is a crucial process to deal with the amount of text published daily, e.g. to find missing associations in a database. RE is a text mining task for which the state-of-the-art approaches use bidirectional encoders, namely, BERT. However, state-of-the-art performance may be limited by the lack of efficient external knowledge injection approaches, with a larger impact in the biomedical area given the widespread usage and high quality of biomedical ontologies. This knowledge can propel these systems forward by aiding them in predicting more explainable biomedical associations. With this in mind, we developed K-RET, a novel, knowledgeable biomedical RE system that, for the first time, injects knowledge by handling different types of associations, multiple sources and where to apply it, and multi-token entities. Results We tested K-RET on three independent and open-access corpora (DDI, BC5CDR, and PGR) using four biomedical ontologies handling different entities. K-RET improved state-of-the-art results by 2.68% on average, with the DDI Corpus yielding the most significant boost in performance, from 79.30% to 87.19% in F-measure, representing a P-value of 2.91×10−12. Availability and implementation https://github.com/lasigeBioTM/K-RET.

Sousa, Diana F. (ORCID:0000000305979273)↗