Search NASA⌕ Search

SEARCH · Search NASA

Results for “Protection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

Material development aspects of an oxidation protection system for a reinforced carbon-carbon composite

The paper describes the procedures which led to selection of a diffusion-coated siliconized oxidation-resistant reinforced carbon-carbon composite as a candidate for use in the leading edge structure of the Space Shuttle for the purpose of providing thermal protection. Materials were evaluated on the basis of oxidation-inhibitor performance, strength properties, and fabricability. Compounds of titanium, tantalum, zirconium, silicon, hafnium, aluminum, and boron were compounded with the reinforced carbon-carbon material in two different processing techniques to discover an oxidation-inhibited system which provided multicycle protection at temperatures up to 4000 F. Details of the manufacture and testing of the reinforced carbon-carbon composites are provided.

Rogers, D. C.↗

Arc discharge supply component protection circuitry

In a mercury-bombardment ion engine, the discharge supply is a high-current low-voltage one that maintains an arc or discharge inside the engine. In a 30-cm engine the supply provides up to 45 volts at about 13 amperes and is referenced at approximately 1100 volts above ground. Due to the engine discharge characteristics, a very slow feedback control loop is required. A high-speed current limit must be used to protect the components in the power conditioner, a pulse-width-modulated bridge inverter. A high-speed cycle-by-cycle current-limit circuit which allows the inverter to continue running in an overcurrent condition is used to protect it. The high-speed current sensing allows the inverter to be turned off each half cycle before the current in the primary of the inverter exceeds a safe level. This permits the inverter to continue to provide current into a discharge or a fault condition, until the feedback control system can actively control the current.

Ahrens, A. F.↗

Ceramic composite protection for turbine disc bursts

Ceramic composite turbine disc protection panels for the A300B were developed using armor technology. Analytical predictions for modifying the ballistic projectile armor system were verified by a test program conducted to qualify the rotor containment system. With only a slight change in the areal density of the armor system a more than two-fold increase in kinetic energy protection level was achieved. Thickness of the fiberglass reinforced plastic backing material was increased to achieve an optimum ratio of ceramic thickness to backing thickness for the different ballistic defeat condition.

Gardner, P. B.↗

Fuel system protection

The hazardous nature of most fuels and the potential for catastrophe if ignition should occur was investigated in regard to the design of adequate lightning protection for aircraft fuel systems. Typical aircraft fuel flammability characteristics and possible ways to control fuel flammability and ignition were reviewed. Guidelines for effective protection of fuel systems were delineated.

Franklin A Fisher↗

Structures Protection

Materials of which an aircraft is made and the methods used to hold these materials together forming the aircraft structure were studied as factors important in protecting a modern aircraft from hazardous natural environments. Since all-metal aircraft are being replaced by aircraft constructed partly of fiber reinforced plastics with desirable light weight and high strength properties but with poor electrical conductivity, the danger of lightning strikes has become more serious. Lightning effects on metal structures were reviewed and design protection was discussed. The expected lightning effects on nonmetallic materials such as fiberglass and advanced composites were also reviewed.

Franklin A Fisher↗

Electroplating offers embrittlement protection

Thin copper electrodeposited layer protects metal parts in environments with which they may be incompatible. Originally developed for main engine of Space Shuttle where high strength nickle alloy bellows must operate in high-pressure hydrogen, technique protects nickel and is unaffected by forming process or subsequent heat treatment and preinstallation processing.

Daniels, C. M., Jr.↗

Tests of a protective shell passive release mechanism for hypersonic wind-tunnel models

A protective shell mechanism for wind tunnel models was developed and tested. The mechanism is passive in operation, reliable, and imposes no new structural design changes for wind tunnel models. Methods of predicting the release time and the measured loads associated with the release of the shell are given. The mechanism was tested in a series of wind tunnel tests to validate the removal process and measure the pressure loads on the model. The protective shell can be used for wind tunnel models that require a step input of heating and loading such as a thin skin heat transfer model. The mechanism may have other potential applications.

Puster, R. L.↗

Flight test evaluation of an RAF high altitude partial pressure protective assembly

A partial pressure suit was evaluated during tests in an F-104 and F-15 as a protective garment for emergency descents. The garment is an pressure jerkin and modified anti-g suit combined with an oronasal mask. The garment can be donned and doffed at the aircraft to minimize thermal buildup. The oronasal mask was favored by the pilots due to its immobility on the face during high g-loading. The garment was chosen to provide optimum dexterity for the pilot, which is not available in a full pressure suit, while protecting the pilot at altitudes up to 18,288 meters, during a cabin decompression, and subsequent aircraft descent. During cabin decompressions in the F-104 and F-15, cabin pressure altitude was measured at various aircraft angles of attack, Mach numbers, and altitudes to determine the effect of the aerodynamic slipstream on the cabin altitude.

Ashworth, G. R.↗

Feasibility study of silicon nitride protection of plastic encapsulated semiconductors

The application of low temperature silicon nitride protective layers on wire bonded integrated circuits mounted on lead frame assemblies is reported. An evaluation of the mechanical and electrical compatibility of both plasma nitride and photochemical silicon nitride (photonitride) passivations (parallel evaluations) of integrated circuits which were then encapsulated in plastic is described. Photonitride passivation is compatible with all wire bonded lead frame assemblies, with or without initial chip passivation. Plasma nitride passivation of lead frame assemblies is possible only if the chip is passivated before lead frame assembly. The survival rate after the environmental test sequence of devices with a coating of plasma nitride on the chip and a coating of either plasma nitride or photonitride over the assembled device is significantly greater than that of devices assembled with no nitride protective coating over either chip or lead frame.

Peters, J. W.↗

Space Shuttle Orbiter thermal protection material development and testing

The research work described in the present paper was carried out to develop and evaluate thermal protection materials for application to the Space Shuttle and future programs. The philosophy, methodology of testing, and facilities are discussed which had to be developed in view of the new requirements placed on the thermal protection system, in particular the requirement of multiple flight capability.

Larson, H. K.↗

Ulcers in restrained rats: Study of protective substances

The genesis of ulcers in restrained rats is discussed through an investigation of the relationship between the protective effects of nervous system effectual substances examined vis-a-vis ulcers in restrained rats and their elective or secondary pharmacologic effects. The substances used were capable of either peripheral parasympatholytic, sympatholytic, ganglioplegic, spasmolytic effects or central, hypnotic, tranquilizing, neuroleptic, analgesic effects. The regular and considerable protection observed with parasympatholytics (atropine sulfate, benzylonium bromide, dihexyverine, J.L. 1344) and a ganglioplegic (pentamethonium) is a function of their anticholinergic properties. It is of less importance with dibenamine, a sympatholytic action on the adrenergic receptors. Among the central depressive substances tested (hypnotics, tranquilizers, neuroleptics, analgesic), phenobarbital at a nonhypnotic dose, and dextromoramide at a nonanalgesic dose, show antiulcerous effects, which are found with chlorpromazine only at cataleptogenic doses.

Buche, L.↗

Project FIRES. Volume 4: Prototype Protective Ensemble Qualification Test Report, Phase 1B

The qualification testing of a prototype firefighter's protective ensemble is documented. Included are descriptions of the design requirements, the testing methods, and the test apparatus. The tests include measurements of individual subsystem characteristics in areas relating to both physical testing, such as heat, flame, impact penetration and human factors testing, such as dexterity, grip, and mobility. Also, measurements related to both physical and human factors testing of the complete ensemble, such as water protection, metabolic expenditures, and compatibility are considered.

Abeles, F. J.↗

Project FIRES - Firefighters Integrated Response Equipment System. Volume 3: Protective Ensemble Design and Procurement Specification, Phase 1B

Each of the subsystems comprising the protective ensemble for firefighters is described. These include: (1) the garment system which includes turnout gear, helmets, faceshields, coats, pants, gloves, and boots; (2) the self-contained breathing system; (3) the lighting system; and (4) the communication system. The design selection rationale is discussed and the drawings used to fabricate the prototype ensemble are provided. The specifications presented were developed using the requirements and test method of the protective ensemble standard. Approximate retail prices are listed.

Abeles, F. J.↗

Description of the manufacturing challenges in producing the high-temperature reusable surface insulation for the thermal protection system of the Space Shuttle

The paper describes the high-temperature reusable surface insulation for the thermal protection system of the Space Shuttle. This system protects the Space Shuttle Orbiter on reentry and it is an externally attached, rigidized, fibrous silica, machined into 15 x 20 cm tiles. The tiles constitute the High-Temperature Reusable Surface Insulation (HRSI) system, and are used on over 70 percent of the exterior surface where peak temperatures range from 400 to 1260 C. Carbon-carbon leading edges are used in areas where peak temperatures exceed 1650 C, and a Nomex felt flexible insulation system is used in regions below 400 C. Approximately 32,000 tiles are used in the HRSI system, and due to vehicle configuration and aerodynamic requirements no two tiles are alike.

Forsberg, K.↗

Protective Garment Ensemble

Protective garment ensemble with internally-mounted environmental- control unit contains its own air supply. Alternatively, a remote-environmental control unit or an air line is attached at the umbilical quick disconnect. Unit uses liquid air that is vaporized to provide both breathing air and cooling. Totally enclosed garment protects against toxic substances.

Wakefield, M. E.↗

Ion beam deposited protective films

Single or dual ion beam sources were used to deposit thin films for different applications. Metal and metal oxide films were evaluated as protective coatings for the materials. Film adherence was measured and the most promising films were then tested under environments similar to operating conditions. It was shown that some materials do protect die material (H-13 steel) and do reduce thermal fatigue. Diamondlike films have many useful applications. A series of experiments were conducted to define and optimize new approaches to the manufacture of such films. A dual beam system using argon and methane gases was developed to generate these films.

Mirtich, M. J.↗