Search NASA⌕ Search

SEARCH · Search NASA

Results for “computational fluid dynamics simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

Importance of Body Stance in Fog Droplet Collection by the Namib Desert Beetle

The fog-basking behavior of the Onymacris unguicularis, a beetle species living in the coastal regions of the Namibian desert, has recently caught the attention of the engineering community, as suggesting a viable biomimetic approach to address the problem of harvesting water in arid regions of the globe. Previous research has focused on observation and analysis of the beetle’s elytron properties and how these affect fog-collection rates. The head stance taken by the Onymacris unguicularis when fog basking is well documented. However, how this stance affects droplet collection has not been studied up to now. The present paper addresses this problem from a computational fluid dynamics perspective, where three-dimensional numerical simulations are used to characterize the fog flow properties around a simplified geometry mimicking the beetle’s body. The simulations employ two-way coupling between the gas flow and the dispersed fog phase to account for feedback effects of fog droplets on the carrier fluid (air), and assume that droplets are captured after hitting the elytron surface. The study considers several combinations of free-stream velocity and droplet volume fraction. The analysis reveals that there is a range of head-stance angles, corresponding to an inclination of the beetle between 35 deg and 45 deg with respect to the horizon, that maximizes water collection on the beetle’s back, in qualitative agreement with observations in nature and laboratory experiments. A rationale is proposed to explain this phenomenon, finding that the specific head stance corresponds to the maximum residence time of fluid particles above the beetle’s elytron surface. This, in turn, designates the maximum likelihood for water droplets to be captured in the boundary layer developing over the beetle and subsequently hit the surface where they get captured. The results reveal the importance of the fluid flow pattern around the beetle’s body in addition to the microphysical properties of the elytron when reliable predictions of the water droplet collection efficiency are sought.

Chakrabarti, Unmeelan↗

Computational Fluid Dynamics Program at NASA Ames Research Center

The Computational Fluid Dynamics (CFD) Program at NASA Ames Research Center is reviewed and discussed. The technical elements of the CFD Program are listed and briefly discussed. These elements include algorithm research, research and pilot code development, scientific visualization, advanced surface representation, volume grid generation, and numerical optimization. Next, the discipline of CFD is briefly discussed and related to other areas of research at NASA Ames including experimental fluid dynamics, computer science research, computational chemistry, and numerical aerodynamic simulation. These areas combine with CFD to form a larger area of research, which might collectively be called computational technology. The ultimate goal of computational technology research at NASA Ames is to increase the physical understanding of the world in which we live, solve problems of national importance, and increase the technical capabilities of the aerospace community. Next, the major programs at NASA Ames that either use CFD technology or perform research in CFD are listed and discussed. Briefly, this list includes turbulent/transition physics and modeling, high-speed real gas flows, interdisciplinary research, turbomachinery demonstration computations, complete aircraft aerodynamics, rotorcraft applications, powered lift flows, high alpha flows, multiple body aerodynamics, and incompressible flow applications. Some of the individual problems actively being worked in each of these areas is listed to help define the breadth or extent of CFD involvement in each of these major programs. State-of-the-art examples of various CFD applications are presented to highlight most of these areas. The main emphasis of this portion of the presentation is on examples which will not otherwise be treated at this conference by the individual presentations. Finally, a list of principal current limitations and expected future directions is given.

Holst, Terry L.↗

A numerical and experimental analysis of reactor performance and deposition rates for CVD on monofilaments

The computational fluid dynamics (CFD) code FLUENT is adopted to simulate a cylindrical upflow reactor designed for chemical vapor deposition (CVD) on monofilaments. Equilibrium temperature profiles along the fiber and quartz reactor wall are experimentally measured and used as boundary conditions in numerical simulations. Two-dimensional axisymmetric flow and temperature fields are calculated for hydrogen and argon; the effect of free convection is assessed. The gas and surface chemistry is included for predicting silicon deposition from silane. The model predictions are compared with experimentally measured silicon CVD rates. Inferences are made for optimum conditions to obtain uniformity.

Gokoglu, S. A.↗

Prediction of pressure drop in fluid tuned mounts using analytical and computational techniques

A simplified model for predicting pressure drop in fluid tuned isolator mounts was developed. The model is based on an exact solution to the Navier-Stokes equations and was made more general through the use of empirical coefficients. The values of these coefficients were determined by numerical simulation of the flow using the commercial computational fluid dynamics (CFD) package FIDAP.

Lasher, William C.↗

Potential Flow Analysis of Dynamic Ground Effect

Interpretation of some flight test data suggests the presence of a 'dynamic ground effect'. The lift of an aircraft approaching the ground depends on the rate of descent and is lower than the aircraft steady state lift at a same height above the ground. Such a lift deficiency under dynamic conditions could have a serious impact on the overall aircraft layout. For example, the increased pitch angle needed to compensate for the temporary loss in lift would reduce the tail strike margin or require an increase in landing gear length. Under HSR2 an effort is under way to clarify the dynamic ground effect issue using a multi-pronged approach. A dynamic ground effect test has been run in the NASA Langley 14x22 ft wind tunnel. Northup-Grumman is conducting time accurate CFD (Computational Fluid Dynamics) Euler analyses on the National Aerodynamic Simulator facility. Boeing has been using linear potential flow methodology which are thought to provide much needed insight in, physics of this very complex problem. The present report summarizes the results of these potential flow studies.

W. M. Feifel↗

Computational Modeling of the Ames 11-Ft Transonic Wind Tunnel in Conjunction with IofNEWT

Technical advances in Computational Fluid Dynamics have now made it possible to simulate complex three-dimensional internal flows about models of various size placed in a Transonic Wind Tunnel. TWT wall interference effects have been a source of error in predicting flight data from actual wind tunnel measured data. An advantage of such internal CFD calculations is to directly compare numerical results with the actual tunnel data for code assessment and tunnel flow analysis. A CFD capability has recently been devised for flow analysis of the NASA/Ames 11-Ft TWT facility. The primary objectives of this work are to provide a CFD tool to study the NASA/Ames 11-Ft TWT flow characteristics, to understand the slotted wall interference effects, and to validate CFD codes. A secondary objective is to integrate the internal flowfield calculations with the Pressure Sensitive Paint data, a surface pressure distribution capability in Ames' production wind tunnels. The effort has been part of the Ames IofNEWT, Integration of Numerical and Experimental Wind Tunnels project, which is aimed at providing further analytical tools for industrial application. We used the NASA/Ames OVERFLOW code to solve the thin-layer Navier-Stokes equations. Viscosity effects near the model are captured by Baldwin-Lomax or Baldwin-Barth turbulence models. The solver was modified to model the flow behavior in the vicinity of the tunnel longitudinal slotted walls. A suitable porous type wall boundary condition was coded to account for the cross-flow through the test section. Viscous flow equations were solved in generalized coordinates with a three-factor implicit central difference scheme in conjunction with the Chimera grid procedure. The internal flow field about the model and the tunnel walls were descretized by the Chimera overset grid system. This approach allows the application of efficient grid generation codes about individual components of the configuration; separate minor grids were developed to resolve the model and overset onto a main grid which discretizes the interior of the tunnel test section. Individual grid components axe not required to have mesh boundaries joined in any special way to each other or to the main tunnel grid. Programs have been developed to rotate the model about the tunnel pivot point and rotation axis, similar to that of the tunnel turntable mechanism for adjusting the pitch of the physical model in the test section.

Djomehri, M. Jahed↗

Aeroheating and Aerodynamic CFD Validation And Prediction for The X-38 Program

This paper presents the results of a computational fluid dynamics validation exercise using the General Aerodynamic Simulation Program (GASP) code for vehicles under consideration for the X-38 program. The scope of the exercise involved simulation and comparison with wind tunnel aeroheating and aerodynamic data in the hypersonic regime. In addition, simulations were performed and results are presented for the full-scale flight vehicle along an expected re- entry trajectory.

Loomis, Mark P.↗

Wind-US 1.0 Released by NPARC Alliance

The NPARC (National Project for Application-oriented Research in CFD) Alliance has released Version 1.0 of Wind-US, the latest in its line of general-purpose, multizone, compressible-flow Navier-Stokes solvers. The NPARC Alliance is a formal partnership between the NASA Glenn Research Center and the Air Force Arnold Engineering Development Center, with additional significant involvement by the Boeing Company s Phantom Works Group, whose mission is to provide an applications-oriented computational fluid dynamics (CFD) system primarily for aerospace flow simulation. The alliance is committed to the long-range maintenance and improvement of this capability, with teams focused on user support, code development, and validation.

Towne, Charles E.↗

Sloshing in Liquid Hydrogen and LOX Propellant Tanks After Main Engine Cut-off

NASA Marshall Space Flight Center is designing and developing the Main Propulsion System (MPS) for Ares launch vehicles. The objective of this study is to calculate the sloshing forces and moments in the LH2 and LO2 propellant tanks using a CFD/VOF analysis under realistic flight conditions. Propellant sloshing in the liquid hydrogen (LH2) and the liquid oxygen (LO2) propellant tanks after Main Engine Cut Off (MECO) was modeled using the Volume of Fluid (VOF) module of the computational fluid dynamics code, CFD-ACE+. The present simulation shows that there are substantial sloshing side forces acting on the LH2 tank during the deceleration of the vehicle after MECO. The LH2 tank features a side wall drain pipe. The side loads result from the residual propellant mass motion in the LH2 tank which is initiated by the stop of flow into the drain pipe at MECO. The simulations show that radial force on the LH2 tank wall is less than 50 lbf and the radial moment calculated based up the center of gravity of the vehicle is predicted to be as high as 300 lbf-ft. The LO2 tank features a bottom dome drain system and is equipped with sloshing baffles. The remaining LO2 in the tank slowly forms a liquid column along the centerline of tank under the zero gravity environments. The radial force on the LO2 tank wall is predicted less than 100 lbf. The radial moment calculated based on the center of gravity of the vehicle is predicted as high as 4500 lbf-ft just before MECO and dropped down to near zero after propellant draining stopped completely.

Kim, Sura↗

Sloshing in the Liquid Hydrogen and Liquid Oxygen Propellant Tanks After Main Engine Cut Off

NASA Marshall Space Flight Center is designing and developing the Main Propulsion System (MPS) for Ares launch vehicles. Propellant sloshing in the liquid hydrogen (LH2) and liquid oxygen (LO2) propellant tanks after Main Engine Cut Off (MECO) was modeled using the Volume of Fluid (VOF) module of the computational fluid dynamics code, CFD-ACE+. The present simulation shows that there is substantial sloshing side forces acting on the LH2 tank during the deceleration of the vehicle after MECO. The LH2 tank features a side wall drain pipe. The side loads result from the residual propellant mass motion in the LH2 tank which is initiated by the stop of flow into the drain pipe at MECO. The simulations show that radial force on the LH2 tank wall is less than 50 lbf and the radial moment calculated based up through the center of gravity of the vehicle is predicted to be as high as 300 lbf-ft. The LO2 tank features a bottom dome drain system and is equipped with sloshing baffles. The remaining LO2 in the tank slowly forms a liquid column along the centerline of tank under the zero gravity environments. The radial force on the LO2 tank wall is predicted to be less than 100 lbf. The radial moment calculated based on the center of gravity of the vehicle is predicted as high as 4500 lbf-ft just before MECO and dropped down to near zero after propellant draining stopped completely.

Kim, Sura↗

Wind Tunnel Testing of a 120th Scale Large Civil Tilt-Rotor Model in Airplane and Helicopter Modes

In April 2012 and October 2013, NASA and the U.S. Army jointly conducted a wind tunnel test program examining two notional large tilt rotor designs: NASA's Large Civil Tilt Rotor and the Army's High Efficiency Tilt Rotor. The approximately 6%-scale airframe models (unpowered) were tested without rotors in the U.S. Army 7- by 10-foot wind tunnel at NASA Ames Research Center. Measurements of all six forces and moments acting on the airframe were taken using the wind tunnel scale system. In addition to force and moment measurements, flow visualization using tufts, infrared thermography and oil flow were used to identify flow trajectories, boundary layer transition and areas of flow separation. The purpose of this test was to collect data for the validation of computational fluid dynamics tools, for the development of flight dynamics simulation models, and to validate performance predictions made during conceptual design. This paper focuses on the results for the Large Civil Tilt Rotor model in an airplane mode configuration up to 200 knots of wind tunnel speed. Results are presented with the full airframe model with various wing tip and nacelle configurations, and for a wing-only case also with various wing tip and nacelle configurations. Key results show that the addition of a wing extension outboard of the nacelles produces a significant increase in the lift-to-drag ratio, and interestingly decreases the drag compared to the case where the wing extension is not present. The drag decrease is likely due to complex aerodynamic interactions between the nacelle and wing extension that results in a significant drag benefit.

Wind Tunnel Testing of a 1/20th Scale↗

Economical Unsteady High-Fidelity Aerodynamics for Structural Optimization with a Flutter Constraint

Structural optimization with a flutter constraint for a vehicle designed to fly in the transonic regime is a particularly difficult task. In this speed range, the flutter boundary is very sensitive to aerodynamic nonlinearities, typically requiring high-fidelity Navier-Stokes simulations. However, the repeated application of unsteady computational fluid dynamics to guide an aeroelastic optimization process is very computationally expensive. This expense has motivated the development of methods that incorporate aspects of the aerodynamic nonlinearity, classical tools of flutter analysis, and more recent methods of optimization. While it is possible to use doublet lattice method aerodynamics, this paper focuses on the use of an unsteady high-fidelity aerodynamic reduced order model combined with successive transformations that allows for an economical way of utilizing high-fidelity aerodynamics in the optimization process. This approach is applied to the common research model wing structural design. As might be expected, the high-fidelity aerodynamics produces a heavier wing than that optimized with doublet lattice aerodynamics. It is found that the optimized lower skin of the wing using high-fidelity aerodynamics differs significantly from that using doublet lattice aerodynamics.

Bartels, Robert E.↗

Isolated Rotor Forward Flight Testing from One Atmosphere down to Martian Atmospheric Densities

With the recent interest in Martian exploration using Unmanned Aerial Vehicles (UAV), an experimental study was conducted to investigate rotor performance at Martian atmospheric conditions. Both simulation and testing of rotors is vital for the evaluation of performance and behavior of a rotor, especially when subjected to a Marian atmosphere. One critical test that has not been performed to date is simulated helicopter forward flight in a Martian atmosphere. To achieve this, the test must be conducted in a facility which can be evacuated to the atmospheric pressure and density of Mars. A unique 40-in diameter rotor, roughly approximating a proposed design for a Mars Helicopter (MH), was tested in forward flight at Mars atmospheric pressure at the NASA Ames Planetary Aeolian Laboratory (PAL). The goal of this experiment was to collect rotor thrust, RPM, power, torque, and acoustics measurements. Subsequently, these results are compared with simulated cases using a mid-fidelity Computational Fluid Dynamics (CFD) approach. As expected, rotor thrust and power results are drastically reduced when under low atmospheric conditions. In addition, Reynolds number effects seem to play a vital role that cannot be neglected.

Ament, Geoffrey A.↗

Hybrid CFD Engineering Model of Plume Induced Erosion and Crater Formation During Descent of Lunar Landers

With rapidly increased worldwide interest in landing on the moon, the issue of Plume Surface Interactions (PSI) is gaining attention. Hazards posed by lander plume induced dust and debris, as well as landing site deformation can be mitigated when better understood through predictive simulations. As simulation enabling computational power continues to increase, hybrid Computational Fluid Dynamics (CFD)/Engineering models provide the immediate ability to conduct parametric/trade studies driving design decisions for landers. Reduced order erosion engineering models apply correlations of the surface erosion rate to the plume induced surface forces with the correlations anchored to flight observations from Apollo LM landings. The MSFC propulsion fluid dynamics branch has developed such a hybrid model for predicting the plume induced viscous erosive regression of the Lunar surface beneath a landing vehicle. The (Descent Interpolated Gas Granular Erosion Model) DIGGEM was originally implemented as a post processing tool to calculate induced erosion rates through vehicle descent using CFD solutions of the vehicle plume at several fixed altitudes. This capability has since been advanced in the Loci/Chem-DIGGEM model to allow transient, moving vehicle, fully coupled viscous erosion modeling of vehicle descent PSI. This model has recently been used to make preflight predictions of the erosive regression of the ground beneath a Commercial Lunar Payload Services (CLPS) vehicle in support of measurements to be made by the Stereo Cameras for Lunar Plume Surface Studies (SCALPSS) instrument.

Plume Surface Interaction↗

Hybrid CFD Engineering Model of Plume Induced Erosion and Crater Formation During Descent of Lunar Landers

With rapidly increased worldwide interest in landing on the moon, the issue of Plume Surface Interactions (PSI) is gaining attention. Hazards posed by lander plume induced dust and debris, as well as landing site deformation can be mitigated when better understood through predictive simulations. As simulation enabling computational power continues to increase, hybrid Computational Fluid Dynamics (CFD)/Engineering models provide the immediate ability to conduct parametric/trade studies driving design decisions for landers. Reduced order erosion engineering models apply correlations of the surface erosion rate to the plume induced surface forces with the correlations anchored to flight observations from Apollo LM landings. The MSFC propulsion fluid dynamics branch has developed such a hybrid model for predicting the plume induced viscous erosive regression of the Lunar surface beneath a landing vehicle. The (Descent Interpolated Gas Granular Erosion Model) DIGGEM was originally implemented as a post processing tool to calculate induced erosion rates through vehicle descent using CFD solutions of the vehicle plume at several fixed altitudes. This capability has since been advanced in the Loci/Chem-DIGGEM model to allow transient, moving vehicle, fully coupled viscous erosion modeling of vehicle descent PSI. This model has recently been used to make preflight predictions of the erosive regression of the ground beneath a Commercial Lunar Payload Services (CLPS) vehicle in support of measurements to be made by the Stereo Cameras for Lunar Plume Surface Studies (SCALPSS) instrument.

Plume Surface Interaction↗

String Potentiometers for Supersonic Split-Line Thrust Vector Amplification Factor Verification

The static fire of NASA’s Mars Ascent Vehicle (MAV) first stage Solid Rocket Motor (SRM1) Demonstration Motor-1 (DM-1) occurred at Edwards Air Force Base (AFB) on April 7, 2023. Among other objectives, this test successfully demonstrated the Thrust Vector Control (TVC) system, including the Technology Readiness Level (TRL) of the Supersonic Split-Line (SSSL) nozzle. An essential characteristic of the SSSL is the thrust vector amplification factor (TVAF) it exhibits; however, empirically quantifying this behavior is difficult due to the limitations of measuring the internal nozzle gas dynamics of a Solid Rocket Motor (SRM) during burn. Using four string potentiometers mounted inside the test chamber connected to the nozzle and motor case and a thrust measurement system (TMS), the TVAF can be derived from the known nozzle and motor geometry. Increasing the accuracy of the TVAF is essential for certain groups working on the MAV including the Guidance, Navigation, and Control (GN&C) group, who prior to DM-1, solely relied on Computational Fluid Dynamics (CFD) data in their Monte Carlo simulations for TVAF. The methodology shown in this paper can be generally applied to any test article implementing a SSSL nozzle, presuming string potentiometers are a viable option and the facility is conducive of their implementation.

Supersonic Split-Line↗

Aerodynamics of a Uranus Aerocapture System Using a Mars-Heritage Entry Vehicle

Aerodynamic characteristics of an aerocapture system intended to deliver a flagship-class orbiter and probe planetary science mission to Uranus are presented. The aeroshell of the Mars Science Laboratory and Mars 2020 entry vehicles is proposed as a baseline for this system to reduce the amount of necessary technology development. Direct Simulation Monte Carlo and Navier-Stokes computational fluid dynamics solutions are used to characterize the aerodynamic performance of the Mars-heritage vehicle for aerocapture flight at Uranus. These results are incorporated into an aerodatabase for use in six degree-of-freedom trajectory studies and mission design. Updates are made to the Mars-heritage aerodynamic uncertainty model based on observations in the Uranus-specific computational data to ensure the model is conservatively bounding for the proposed flight space. Necessary modifications to the aeroshell for system packaging are found to have minimal effect on aerodynamic performance. The resulting aerodatabase and uncertainty model are used to show the existing Mars-heritage entry vehicles have sufficient aerodynamic performance to achieve required control margin for Uranus aerocapture.

Eli R Shellabarger↗

Aerodynamics of a Uranus Aerocapture System Using a Mars-Heritage Entry Vehicle

Aerodynamic characteristics of an aerocapture system intended to deliver a flagship-class orbiter and probe planetary science mission to Uranus are presented. The aeroshell of the Mars Science Laboratory and Mars 2020 entry vehicles is proposed as a baseline for this system to reduce the amount of necessary technology development. Direct Simulation Monte Carlo and Navier-Stokes computational fluid dynamics solutions are used to characterize the aerodynamic performance of the Mars-heritage vehicle for aerocapture flight at Uranus. These results are incorporated into an aerodatabase for use in six degree-of-freedom trajectory studies and mission design. Updates are made to the Mars-heritage aerodynamic uncertainty model based on observations in the Uranus-specific computational data to ensure the model is conservatively bounding for the proposed flight space. Necessary modifications to the aeroshell for system packaging are found to have minimal effect on aerodynamic performance. The resulting aerodatabase and uncertainty model are used to show the existing Mars-heritage entry vehicles have sufficient aerodynamic performance to achieve required control margin for Uranus aerocapture.

Eli Shellabarger↗