Results for “hover” — Page 78

NASA NTRSDate not supplied

Assured Vehicle Automation 1 Sim - Results Outbrief

In early 2022, the Human Autonomy Teaming Lab (NASA Ames Research Center) conducted a manned, human-in-the-loop (HITL) simulation. This part-task HITL began the lab’s Hazard Perception and Avoidance (HPA) technical work under NASA’s Advanced Air Mobility (AAM), Automated Flight and Contingency Management (AFCM) Sub-Project. The results of that sim guided the objectives of the current study, which were to examine pilots’ use of the Airborne Collision Avoidance System (ACAS) rotorcraft variant (Xr) v2 in multiple phases of flight with two separate Xr Modes, fully leverage Xr v2 features (e.g., use radar altimeter data to inform low altitude Resolution Advisory [RA] behavior, utilize the ability to designate “terminal-area intruders,” and display airspeed-based Detect and Avoid [DAA] guidance), emulate a “Traffic Advisory” (TA), and present Xr in a higher-fidelity environment. Therefore, this study was conducted in the Vertical Motion Simulator, and the variables included Phase of Flight (En-route, Hover, and Approach) as well as ACAS Xr Mode (TA/RA and DAA). The data collected included response times, losses of well clear, and maneuver sizes and durations as well as subjective ratings like acceptability and usability. Additional details and future anticipations are also discussed.

air taxis↗

NASA NTRS2023

Performance, Inflow, and Tip Loss Characteristics of Rotors with Discontinuous Steps in Twist and Lift at the Blade-Tips

This paper examines the inflow and tip-loss characteristics of rotors incorporating indexed blade-tips that have discontinuous steps in twist or lift distribution. An extension of the classic two-dimensional Prandtl tip loss analysis is derived for indexed-tip rotors and proprotors. Additionally, parametric analysis of tip span and indexed-tip twist-steps was performed using computational fluid dynamics for hover and high-speed axial-flow conditions for proprotors. The intent of this work is to define a new class of active-rotor-twist-control designs for proprotors that avoids unnecessary aeroperformance compromises for rotor twist distributions for proprotors in all phases of flight.

rotors↗

NASA NTRS2023

Performance Modeling of Urban Air Mobility Vehicles to Support Air Traffic Management Research

The recent emergence of Urban Air Mobility (UAM) vehicles has resulted in a need for flight performance models that enable comprehensive simulation-based research on air traffic management topics such as route structure, scheduling, and separation standards. Successful performance modeling methods exist for a wide range of traditional aircraft designs. However, comparable modeling methods appropriate for UAM vehicles that combine fixed-wing and rotorcraft performance have not yet been established. One challenge to progress has been the lack of available data capturing the performance characteristics and unique flight profiles of these aircraft. This paper describes methods used to generate the required performance data and the development of performance models for UAM vehicles. Included is a review of the energy and power equations often used in developing performance models for traditional aircraft as well as a discussion of their applicability to UAM vehicles. The challenge of generating realistic performance data in over-actuated vehicles transitioning from hover to cruise flight is also addressed through an approach based on objective function optimization. A table-based performance model format adapted to UAM configurations is described, as well as parametric models intended to accompany the performance table to allow detailed modeling of power and fuel consumption during accelerated flight, turning flight, or flight at an arbitrary climb or descent rate. A discussion of future work is also provided, including the need for refinement of UAM performance modeling methods and formats, especially in conjunction with improvements to aerodynamic modeling of vehicles with complex designs where strong interaction effects may dominate important regions of the flight envelope.

Performance Modeling↗

NASA NTRS2023

Performance Modeling of Urban Air Mobility Vehicles to Support Air Traffic Management Research

The recent emergence of Urban Air Mobility (UAM) vehicles has resulted in a need for flight performance models that enable comprehensive simulation-based research on air traffic management topics such as route structure, scheduling, and separation standards. Successful performance modeling methods exist for a wide range of traditional aircraft designs. However, comparable modeling methods appropriate for UAM vehicles that combine fixed-wing and rotorcraft performance have not yet been established. One challenge to progress has been the lack of available data capturing the performance characteristics and unique flight profiles of these aircraft. This paper describes methods used to generate the required performance data and the development of performance models for UAM vehicles. Included is a review of the energy and power equations often used in developing performance models for traditional aircraft as well as a discussion of their applicability to UAM vehicles. The challenge of generating realistic performance data in over-actuated vehicles transitioning from hover to cruise flight is also addressed through an approach based on objective function optimization. A table-based performance model format adapted to UAM configurations is described, as well as parametric models intended to accompany the performance table to allow detailed modeling of power and fuel consumption during accelerated flight, turning flight, or flight at an arbitrary climb or descent rate. A discussion of future work is also provided, including the need for refinement of UAM performance modeling methods and formats, especially in conjunction with improvements to aerodynamic modeling of vehicles with complex designs where strong interaction effects may dominate important regions of the flight envelope.

Performance Modeling↗

NASA NTRSDate not supplied

Modified Cascading Generalized Inverse Control Allocation

The current aviation revolution towards electric propulsion aircraft (e.g., electric vertical takeoff-and-landing) brings unique control challenges. These vehicles are typically over-actuated (more effectors than desired control outcomes), may require control strategies for the three phases of flight (hover, transition and cruise), and currently have limited electric power availability. These vehicle challenges bring the need for optimal control allocation to the forefront of research. A leading control allocation algorithm, used in current flight vehicles, is the Cascading Generalized Inverse (CGI). Unfortunately, the Cascading Generalized Inverse algorithm is unable to achieve some desired outcomes, it intermittently provides non-optimal allocations, and it may fail to preserve moment direction near maximal achievable outcomes. In this research, the shortcomings of the Cascading Generalized Inverse algorithm are addressed by augmenting the algorithm with Scalar Difference Quadratic unsaturation identification and location at each iteration. Rigorous theory is shown that the Modified Cascading Generalized Inverse performs better at obtaining optimal allocations for all attainable outcomes. Numerical case studies for over-actuated vehicles demonstrate resolution to the aforementioned deficiencies.

Control Allocation↗

NASA NTRSDate not supplied

Modified Cascading Generalized Inverse Control Allocation

The current aviation revolution towards electric propulsion aircraft (e.g., electric vertical takeoff-and-landing) brings unique control challenges. These vehicles are typically over-actuated (more effectors than desired control outcomes), may require control strategies for the three phases of flight (hover, transition and cruise), and currently have limited electric power availability. These vehicle challenges bring the need for optimal control allocation to the forefront of research. A leading control allocation algorithm, used in current flight vehicles, is the Cascading Generalized Inverse (CGI). Unfortunately, the Cascading Generalized Inverse algorithm is unable to achieve some desired outcomes, it intermittently provides non-optimal allocations, and it may fail to preserve moment direction near maximal achievable outcomes. In this research, the shortcomings of the Cascading Generalized Inverse algorithm are addressed by augmenting the algorithm with Scalar Difference Quadratic unsaturation identification and location at each iteration. Rigorous theory is shown that the Modified Cascading Generalized Inverse performs better at obtaining optimal allocations for all attainable outcomes. Numerical case studies for over-actuated vehicles demonstrate resolution to the aforementioned deficiencies.

Control Allocation↗

NASA NTRSDate not supplied

Hazard Perception & Avoidance (HPA), Assured Vehicle Automation 1 Simulation (AVA-1h) Results Outbrief

In late 2022, the Human Autonomy Teaming Lab (NASA Ames Research Center) conducted a manned, human-in-the-loop (HITL) simulation. This HITL was the lab’s second Hazard Perception and Avoidance (HPA) technical work under NASA’s Advanced Air Mobility (AAM), Automated Flight and Contingency Management (AFCM) Sub-Project. The goals were to assess detect and avoid technology for manned, electric vertical takeoff and landing (eVTOL) aircraft. This simulation tested Resolution Advisory (RA) responses and return-to-course (RTC) maneuvers for the second version of the Airborne Collision Avoidance System’s (ACAS) rotary-wing (Xr) variant. This was conducted at the center's Vertical Motion Simulator (VMS), on a motion-based platform, and was configured to fly eVTOL aircraft while maneuvering for intruding traffic. Variables for this study included ACAS Xr modes (i.e., TA/RA and DAA) and phases of flight (i.e., Cruise, Hover, and Approach). The data collected included response times, losses of well clear, and pilots' noncompliances to alerts and guidance as well as subjective ratings like acceptability and perceived workload. Additional details and future anticipations are also discussed.

ACAS Xr↗

NASA NTRS2022

Patches of Magnetic Switchbacks and Their Origins

Parker Solar Probe (PSP) has shown that the solar wind in the inner heliosphere is characterized by the quasi omnipresence of magnetic switchbacks ("switchback" hereinafter), local backward bends of magnetic field lines. Switchbacks also tend to come in patches, with a large-scale modulation that appears to have a spatial scale size comparable to supergranulation on the Sun. Here we inspect data from the first 10 encounters of PSP focusing on different time intervals when clear switchback patches were observed by PSP. We show that the switchbacks modulation, on a timescale of several hours, seems to be independent of whether PSP is near perihelion, when it rapidly traverses large swaths of longitude remaining at the same heliocentric distance, or near the radial-scan part of its orbit, when PSP hovers over the same longitude on the Sun while rapidly moving radially inwards or outwards. This implies that switchback patches must also have an intrinsically temporal modulation most probably originating at the Sun. Between two consecutive patches, the magnetic field is usually very quiescent with weak fluctuations. We compare various parameters between the quiescent intervals and the switchback intervals. The results show that the quiescent intervals are typically less Alfvénic than switchback intervals, and the magnetic power spectrum is usually shallower in quiescent intervals. We propose that the temporal modulation of switchback patches may be related to the "breathing" of emerging flux that appears in images as the formation of "bubbles" below prominences in the Hinode/SOT observations.

Solar wind↗

NASA NTRSDate not supplied

Handling Qualities Assessment of Manual Lunar Landing with Display Augmentation

Research and development is being conducted to support data-driven design decisions for manual control and human involvement in the lunar landing task under the Human Landing System (HLS) program within the Artemis campaign. A human-in-the-loop simulator evaluation of the manual control of a lunar landing vehicle in the final approach and landing phase was conducted at NASA Langley Research Center in the Lunar Flight Deck simulator using the Altair Design and Analysis Cycle (DAC)-2 government reference vehicle. The objective was to perform a direct comparison of control law types with display aiding for various rotational control powers being considered under HLS. Ten subjects (four NASA test pilots and six current pilot astronauts) provided Cooper-Harper ratings, NASA Task Load Index workload ratings, and qualitative comments. The piloting task was to assume manual control of the vehicle (including vertical descent rate) at 150 m above the landing zone, fly to a redesignated landing target (which was up to 75 m radially from the center of the landing zone) and to touch down within a position accuracy of 5m. The data showed that the display augmentation in the form of a “hover cue” significantly improved the pilot’s ability to control translation and create satisfactory handling qualities for otherwise sluggish configurations; however, the investigation also showed that display augmentation is not a panacea. Handling qualities problems, including pilot-induced oscillations, and higher workload for the lowest control powers can still be evident.

Lynda Kramer↗

NASA NTRS2023

A Hybrid Transfer Function Procedure for Broadband Auralization Within Small Flight Vehicle Interiors

Auralization of the sound fields within flight vehicle interiors is of interest to aircraft designers considering crew and passenger ride quality. Computer models can be used to predict the filtering effects that the fuselage structure and interior volume have on the exterior sound field in order to simulate the resulting cabin interior noise. However, this can become expensive when a wide frequency range of analysis suitable for passenger auralization is desired. This is particularly the case when using deterministic modeling methods such as finite element analysis (FEA) wherein prohibitively high levels of detail and finite element discretizations are required to resolve the wavelengths at high frequencies. On the contrary, Statistical Energy Analysis (SEA), while not capturing important modal behaviors at low frequencies, is better suited for higher frequency analyses where structural and interior dynamics exhibit high modal overlap and spatially averaged physical quantities suffice. For this reason, a hybrid procedure is considered here that utilizes FE modal solutions at lower frequencies and SEA results at higher frequencies. A transfer function dataset containing the exterior to interior vibroacoustic filtering effect is calculated accordingly and subsequently stored to be used for a variety of exterior dynamic load cases. At low frequencies, the transfer function dataset detail is related to the level of FE model refinement whereas at high frequencies it functions as an equalizer array with a level of detail corresponding to the SEA subsystem partitioning scheme. The above procedure is described herein and demonstrated on a six passenger flight vehicle with eight propulsors in a hover flight condition.

auralization↗

NASA NTRSDate not supplied

An Overview of the Proprotor Performance Test in the 14- by 22-Foot Subsonic Tunnel

This work experimentally investigates the aerodynamic behavior of proprotors across a wide range of angles of attack. These flight conditions are intended to be representative of Urban Air Mobility (UAM) vehicle platforms that utilize articulating propulsors to transition from a vertical takeoff and landing (VTOL) phase typical of a conventional rotorcraft, to an axial mode of forward flight typical of a fixed-wing aircraft. These data are used to identify the potential limits of lower fidelity aerodynamic modeling tools, as well as to inform future acoustic phases of testing. Tests were conducted on two proprotor designs in the NASA Langley 14- by 22-Foot Subsonic Tunnel using an articulating propeller test stand. Hover results identified unique flow physics on one of the proprotors, including severe outboard flow separation and perpendicular blade vortex interactions on the outboard portions of the blades. Transition and forward flight conditions yielded very informative trends in terms of both on- and off-axis forces and moments against which low-fidelity prediction models were compared.

aerodynamics↗

NASA NTRSDate not supplied

High-Fidelity Analysis of Lift+Cruise VTOL Urban Air Mobility Concept Aircraft

This paper presents a high-fidelity multidisciplinary analysis for the NASA lift+cruise vertical takeoff and landing urban air mobility concept aircraft. The reported simulations couple comprehensive rotorcraft aeromechanics and high-fidelity computational fluid dynamics (CFD). Aerodynamic solutions are computed on dynamic, deforming, unstructured, overset grid systems by an unsteady CFD solver, FUN3D, developed at the NASA Langley Research Center. An integrated overset-grid assembler, Yoga, is used for communications between component grids. Two turbulence models are compared for loose-coupling simulations in hover and low-speed forward flight conditions. One model is the negative variant of the one-equation Spalart-Allmaras model (SA-neg), and the other model is the SA-neg-R model adding a simple rotation correction term to the SA-neg model. It demonstrated that the rotation correction in the SA-neg-R turbulence model significantly improves resolution of secondary vortices and wake interactions for rotorcraft simulations.

CFD↗

NASA NTRSDate not supplied

Handling Qualities of Multirotor RPM-Controlled Electric-Vertical Take-Off and Landing (eVTOL) Aircraft for Urban Air Mobility (UAM)

A paradigm shift in rotorcraft design is being led by the prospect of propulsive forces being distributed across multiple rotors, such that each rotor can be directly driven by a dedicated electric motor. Crucially, some designers attempt to utilize these direct-drive mechanisms as the sole form of primary flight control. The feasibility of this design choice remains to be proven at the scales required for passenger transport. The paper presents a preliminary handling qualities analysis, for a six-passenger (1,200 lb payload) electric Hexacopter conceptual design, which shows that Level 1 handling qualities for limited agility operations are possible, provided that electric powertrains can deliver transient peak torques twice as high as the rated continuous torque of the conceptual design. Preliminary predictions are then substantiated by the results from a piloted handling qualities evaluation conducted in the NASA-Ames Vertical Motion Simulator (VMS). Three eVTOL configurations (a quadrotor, a hexacopter and a lift+cruise) with flight control laws implementing different levels of stability augmentation (Attitude Command-Attitude Hold and Translational Rate Command response types) were evaluated in four low speed and hover tasks requiring various levels of agility and precision.

UAM↗

NASA NTRS2023

High-Fidelity Analysis of Lift+Cruise VTOL Urban Air Mobility Concept Aircraft

This paper presents a high-fidelity multidisciplinary analysis for the NASA Lift+Cruise vertical takeoff and landing urban air mobility concept aircraft. The reported simulations couple comprehensive rotorcraft aeromechanics and high-fidelity computational fluid dynamics (CFD). Aerodynamic solutions are computed on dynamic, deforming, unstructured, overset grid systems by an unsteady CFD solver, FUN3D, developed at the NASA Langley Research Center. An integrated overset-grid assembler, Yoga, is used for communications between component grids. Two turbulence models are compared for loose-coupling simulations in hover and low-speed forward flight conditions. One model is the negative variant of the one-equation Spalart-Allmaras model (SA-neg), and the other model is the SA-neg-R model adding a simple rotation correction term to the SA-neg model. It demonstrated that the rotation correction in the SA-neg-R turbulence model significantly improves resolution of secondary vortices and wake interactions for rotorcraft simulations.

CFD↗

NASA NTRS2023

Design Studies on Mechanically Geared, Magnetically Geared, and Direct Drive Drivetrains for UAM Applications

Urban air mobility vehicles require high reliability and high performance electric motor drive trains. In this paper, a design optimization study is carried out to compare mechanically geared, magnetically geared, and direct drive motor drivetrain topology achievable performance in a 100 kW hover power quad rotor propulsor application. Design studies are carried out accounting for a nominal mission profile. Studies are carried out assuming constant propulsor rotor RPMs of 400, 1000, 2000, and 3000 RPM. Results show that mechanically geared drives are the lightest at all RPMs but their weight benefit over direct drive and magnetically geared decays with increased rotor RPM. Direct drive is shown to always achieve the highest efficiency due to its lower motor speed resulting in low electrical frequencies. Magnetically geared drivetrains are shown to need some requirement refinement or technology improvement to provide significant benefit over direct drive drivetrains.

Thomas Tallerico↗

NASA NTRS2023

Design Studies on Mechanically Geared, Magnetically Geared, and Direct Drive Drivetrains for UAM Applications

Urban air mobility vehicles require high reliability and high performance electric motor drive trains. In this paper, a design optimization study is carried out to compare mechanically geared, magnetically geared, and direct drive motor drivetrain topology achievable performance in a 100 kW hover power quad rotor propulsor application. Design studies are carried out accounting for a nominal mission profile. Studies are carried out assuming constant propulsor rotor RPMs of 400, 1000, 2000, and 3000 RPM. Results show that mechanically geared drives are the lightest at all RPMs but their weight benefit over direct drive and magnetically geared decays with increased rotor RPM. Direct drive is shown to always achieve the highest efficiency due to its lower motor speed resulting in low electrical frequencies. Magnetically geared drivetrains are shown to need some requirement refinement or technology improvement to provide significant benefit over direct drive drivetrains.

Thomas Tallerico↗

NASA NTRS2023

A Hybrid Transfer Function Procedure for Broadband Auralization Within Small Flight Vehicle Interiors

Auralization of the sound fields within flight vehicle interiors is of interest to aircraft designers considering crew and passenger ride quality. Computer models can be used to predict the filtering effects that the fuselage structure and interior volume have on the exterior sound field in order to simulate the resulting cabin interior noise. However, this can become expensive when a wide frequency range of analysis suitable for passenger auralization is desired. This is particularly the case when using deterministic modeling methods such as finite element analysis (FEA) wherein prohibitively high levels of detail and finite element discretizations are required to resolve the wavelengths at high frequencies. On the contrary, Statistical Energy Analysis (SEA), while not capturing important modal behaviors at low frequencies, is better suited for higher frequency analyses where structural and interior dynamics exhibit high modal overlap and spatially averaged physical quantities suffice. For this reason, a hybrid procedure is considered here that utilizes FE modal solutions at lower frequencies and SEA results at higher frequencies. A transfer function dataset containing the exterior to interior vibroacoustic filtering effect is calculated accordingly and subsequently stored to be used for a variety of exterior dynamic load cases. At low frequencies, the transfer function dataset detail is related to the level of FE model refinement whereas at high frequencies it functions as an equalizer array with a level of detail corresponding to the SEA subsystem partitioning scheme. The above procedure is described herein and demonstrated on a six passenger flight vehicle with eight propulsors in a hover flight condition.

auralization↗

NASA NTRSDate not supplied

An Overview of the Proprotor Performance Test in the 14- by 22-Foot Subsonic Tunnel

This work experimentally investigates the aerodynamic behavior of proprotors across a wide range of angles of attack. These flight conditions are intended to be representative of Urban Air Mobility (UAM) vehicle platforms that utilize articulating propulsors to transition from a vertical takeoff and landing (VTOL) phase typical of a conventional rotorcraft, to an axial mode of forward flight typical of a fixed-wing aircraft. These data are used to identify the potential limits of lower fidelity aerodynamic modeling tools, as well as to inform future acoustic phases of testing. Tests were conducted on two proprotor designs in the NASA Langley 14- by 22-Foot Subsonic Tunnel using an articulating propeller test stand. Hover results identified unique flow physics on one of the proprotors, including severe outboard flow separation and perpendicular blade vortex interactions on the outboard portions of the blades. Transition and forward flight conditions yielded very informative trends in terms of both on- and off-axis forces and moments against which low-fidelity prediction models were compared.

Nikolas Zawodny↗