Search NASA⌕ Search

SEARCH · Search NASA

Results for “mean squared error”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

Tracking error of 100-m antenna due to wind gust

A procedure is shown to derive root-mean-square tracking error for an antenna system in response to wind gust loading. Example calculations are illustrated for the design of a proposed 100 m antenna. The effect of wind gust correlation is also considered.

Massoudi, M.↗

Sensitivity of thermal inertia calculations to variations in environmental factors

The sensitivity of thermal inertia (TI) calculations to errors in the measurement or parameterization of a number of environmental factors is considered here. The factors include effects of radiative transfer in the atmosphere, surface albedo and emissivity, variations in surface turbulent heat flux density, cloud cover, vegetative cover, and topography. The error analysis is based upon data from the Heat Capacity Mapping Mission (HCMM) satellite for July 1978 at three separate test sites in the deserts of the western United States. Results show that typical errors in atmospheric radiative transfer, cloud cover, and vegetative cover can individually cause root-mean-square (RMS) errors of about 10 percent (with atmospheric effects sometimes as large as 30-40 percent) in HCMM-derived thermal inertia images of 20,000-200,000 pixels.

Kahle, A. B.↗

Levermore-Pomraning Model Results for an Interior Source Binary Stochastic Medium Benchmark Problem

The accuracy of the Levermore-Pomraning model for particle transport through a binary stochastic medium is investigated using an interior source benchmark problem. As in previous comparisons of the model for incident angular flux benchmark problems, the model accurately computes the leakage and the scalar flux distributions for optically thin slabs. The model is less accurate for more optically thick slabs but has a maximum relative error in the leakage of approximately 10% for the problems examined. The maximum root-mean-squared relative errors for the total and material scalar flux distributions approach 65% for the more optically thick slabs. Consistent with previous benchmark comparisons, the results of these interior source benchmark comparisons demonstrate that the Levermore-Pomraning model produces qualitatively correct and semi-quantitatively correct results for both leakage values and scalar flux distributions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Calculating tumor trajectory and dose-of-the-day using cone-beam CT projections

Purpose: Cone-beam CT (CBCT) projection images provide anatomical data in real-time over several respiratory cycles, forming a comprehensive picture of tumor movement. The authors developed and validated a method which uses these projections to determine the trajectory of and dose to highly mobile tumors during each fraction of treatment. Methods: CBCT images of a respiration phantom were acquired, the trajectory of which mimicked a lung tumor with high amplitude (up to 2.5 cm) and hysteresis. A template-matching algorithm was used to identify the location of a steel BB in each CBCT projection, and a Gaussian probability density function for the absolute BB position was calculated which best fit the observed trajectory of the BB in the imager geometry. Two modifications of the trajectory reconstruction were investigated: first, using respiratory phase information to refine the trajectory estimation (Phase), and second, using the Monte Carlo (MC) method to sample the estimated Gaussian tumor position distribution. The accuracies of the proposed methods were evaluated by comparing the known and calculated BB trajectories in phantom-simulated clinical scenarios using abdominal tumor volumes. Results: With all methods, the mean position of the BB was determined with accuracy better than 0.1 mm, and root-mean-square trajectory errors averaged 3.8% ± 1.1% of the marker amplitude. Dosimetric calculations using Phase methods were more accurate, with mean absolute error less than 0.5%, and with error less than 1% in the highest-noise trajectory. MC-based trajectories prevent the overestimation of dose, but when viewed in an absolute sense, add a small amount of dosimetric error (<0.1%). Conclusions: Marker trajectory and target dose-of-the-day were accurately calculated using CBCT projections. This technique provides a method to evaluate highly mobile tumors using ordinary CBCT data, and could facilitate better strategies to mitigate or compensate for motion during stereotactic body radiotherapy.

60 APPLIED LIFE SCIENCES↗

Shape Validation and RF Performance of Inflatable Antennas

Inflatable aperture antennas are an emerging technology that is being investigated for potential use in science and exploration missions. In particular, for missions to Mars and beyond, large deployable aperture antennas can provide the antenna gain required for high data rate communications, where the necessary antenna diameter exceeds the available volume of typical launch vehicle platforms. As inflatable aperture antennas have not been proven fully qualified for space missions, the author's Master's Thesis assessed the Ruze equation in characterizing this antenna technology. Inflatable aperture antennas do not follow a parabolic shape, and so the Ruze equation is not applicable due to the macroscopic shape errors of this technology. Therefore, geometric evaluations of the surface profile cannot simply correlate antenna gain degradation with the root-mean-square shape error with a parabolic surface. Consequently, the focus of this work was to derive an accurate mathematical model of an inflatable aperture antenna in order to characterize its Radio Frequency (RF) performance. Calculus of Variations methodologies were used to derive the surface profile shape of the inflatable aperture antenna. Physical Optics techniques were used to generate the antenna pattern profile. Validation testing of the predicted inflatable antenna shape model was performed through use of Laser Radar metrology measurements on an inflatable test article. Assessments of the RF performance of the inflatable aperture antenna, compared with nominally shaped paraboloidal antennas, were obtained through simulations of both technologies using a common diameter, depth, and arc length. Assessments of the RF performance of the inflatable aperture antenna was also performed against itself for changes in distance of the antenna feed location in the axial direction. Whereas the Ruze equation is limited to assessing gain reduction, this effort will also assess beam spreading and first side lobe angle and magnitude. The ability to characterize the RF response of this antenna will provide for an improved understanding of this technology. The accurate representation of the shape of this type of antenna technology will help to identify the most appropriate ways in which this technology could be utilized in planning future communication architectures for NASA missions to Mars and beyond.

Welch, Bryan W.↗

Shape Validation and RF Performance of Inflatable Antennas

Inflatable aperture antennas are an emerging technology that is being investigated for potential use in science and exploration missions. In particular, for missions to Mars and beyond, large deployable aperture antennas can provide the antenna gain required for high data rate communications, where the necessary antenna diameter exceeds the available volume of typical launch vehicle platforms. As inflatable aperture antennas have not been proven fully qualified for space missions, the author's Master's Thesis assessed the Ruze equation in characterizing this antenna technology. Inflatable aperture antennas do not follow a parabolic shape, and so the Ruze equation is not applicable due to the macroscopic shape errors of this technology. Therefore, geometric evaluations of the surface profile cannot simply correlate antenna gain degradation with the root-mean square shape error with a parabolic surface. Consequently, the focus of this work was to derive an accurate mathematical model of an inflatable aperture antenna to in order to characterize its Radio Frequency (RF) performance. Calculus of Variations methodologies were used to derive the surface profile shape of the inflatable aperture antenna. Physical Optics techniques were used to generate the antenna pattern profile. Validation testing of the predicted inflatable antenna shape model was performed through use of Laser Radar metrology measurements on an inflatable test article. Assessments of the RF performance of the inflatable aperture antenna, compared with nominally shaped paraboloidal antennas, were obtained through simulations of both technologies using a common diameter, depth, and arc length. Assessments of the RF performance of the inflatable aperture antenna was also performed against itself for changes in distance of the antenna feed location in the axial direction. Whereas the Ruze equation is limited to assessing gain reduction, this effort will also assess beam spreading and first side lobe angle and magnitude. The ability to characterize the RF response of this antenna will provide for an improved understanding of this technology. The accurate representation of the shape of this type of antenna technology will help to identify the most appropriate ways in which this technology could be utilized in planning future communication architectures for NASA missions to Mars and beyond.

Welch, Bryan↗

Screening actuator locations for static shape control

Correction of shape distortion due to zero-mean normally distributed errors in structural sizes which are random variables is examined. A bound on the maximum improvement in the expected value of the root-mean-square shape error is obtained. The shape correction associated with the optimal actuators is also characterized. An actuator effectiveness index is developed and shown to be helpful in screening actuator locations in the structure. The results are specialized to a simple form for truss structures composed of nominally identical members. The bound and effectiveness index are tested on a 55-m radiometer antenna truss structure. It is found that previously obtained results for optimum actuators had a performance close to the bound obtained here. Furthermore, the actuators associated with the optimum design are shown to have high effectiveness indices. Since only a small fraction of truss elements tend to have high effectiveness indices, the proposed screening procedure can greatly reduce the number of truss members that need to be considered as actuator sites.

Haftka, Raphael T.↗

Response Surface Modeling Using Multivariate Orthogonal Functions

A nonlinear modeling technique was used to characterize response surfaces for non-dimensional longitudinal aerodynamic force and moment coefficients, based on wind tunnel data from a commercial jet transport model. Data were collected using two experimental procedures - one based on modem design of experiments (MDOE), and one using a classical one factor at a time (OFAT) approach. The nonlinear modeling technique used multivariate orthogonal functions generated from the independent variable data as modeling functions in a least squares context to characterize the response surfaces. Model terms were selected automatically using a prediction error metric. Prediction error bounds computed from the modeling data alone were found to be- a good measure of actual prediction error for prediction points within the inference space. Root-mean-square model fit error and prediction error were less than 4 percent of the mean response value in all cases. Efficacy and prediction performance of the response surface models identified from both MDOE and OFAT experiments were investigated.

Morelli, Eugene A.↗

Optimal Tuner Selection for Kalman Filter-Based Aircraft Engine Performance Estimation

A linear point design methodology for minimizing the error in on-line Kalman filter-based aircraft engine performance estimation applications is presented. This technique specifically addresses the underdetermined estimation problem, where there are more unknown parameters than available sensor measurements. A systematic approach is applied to produce a model tuning parameter vector of appropriate dimension to enable estimation by a Kalman filter, while minimizing the estimation error in the parameters of interest. Tuning parameter selection is performed using a multi-variable iterative search routine which seeks to minimize the theoretical mean-squared estimation error. This paper derives theoretical Kalman filter estimation error bias and variance values at steady-state operating conditions, and presents the tuner selection routine applied to minimize these values. Results from the application of the technique to an aircraft engine simulation are presented and compared to the conventional approach of tuner selection. Experimental simulation results are found to be in agreement with theoretical predictions. The new methodology is shown to yield a significant improvement in on-line engine performance estimation accuracy

Simon, Donald L.↗

Optimal Tuner Selection for Kalman-Filter-Based Aircraft Engine Performance Estimation

An emerging approach in the field of aircraft engine controls and system health management is the inclusion of real-time, onboard models for the inflight estimation of engine performance variations. This technology, typically based on Kalman-filter concepts, enables the estimation of unmeasured engine performance parameters that can be directly utilized by controls, prognostics, and health-management applications. A challenge that complicates this practice is the fact that an aircraft engine s performance is affected by its level of degradation, generally described in terms of unmeasurable health parameters such as efficiencies and flow capacities related to each major engine module. Through Kalman-filter-based estimation techniques, the level of engine performance degradation can be estimated, given that there are at least as many sensors as health parameters to be estimated. However, in an aircraft engine, the number of sensors available is typically less than the number of health parameters, presenting an under-determined estimation problem. A common approach to address this shortcoming is to estimate a subset of the health parameters, referred to as model tuning parameters. The problem/objective is to optimally select the model tuning parameters to minimize Kalman-filterbased estimation error. A tuner selection technique has been developed that specifically addresses the under-determined estimation problem, where there are more unknown parameters than available sensor measurements. A systematic approach is applied to produce a model tuning parameter vector of appropriate dimension to enable estimation by a Kalman filter, while minimizing the estimation error in the parameters of interest. Tuning parameter selection is performed using a multi-variable iterative search routine that seeks to minimize the theoretical mean-squared estimation error of the Kalman filter. This approach can significantly reduce the error in onboard aircraft engine parameter estimation applications such as model-based diagnostic, controls, and life usage calculations. The advantage of the innovation is the significant reduction in estimation errors that it can provide relative to the conventional approach of selecting a subset of health parameters to serve as the model tuning parameter vector. Because this technique needs only to be performed during the system design process, it places no additional computation burden on the onboard Kalman filter implementation. The technique has been developed for aircraft engine onboard estimation applications, as this application typically presents an under-determined estimation problem. However, this generic technique could be applied to other industries using gas turbine engine technology.

Simon, Donald L.↗

Optimized tuner selection for engine performance estimation

A methodology for minimizing the error in on-line Kalman filter-based aircraft engine performance estimation applications is presented. This technique specifically addresses the underdetermined estimation problem, where there are more unknown parameters than available sensor measurements. A systematic approach is applied to produce a model tuning parameter vector of appropriate dimension to enable estimation by a Kalman filter, while minimizing the estimation error in the parameters of interest. Tuning parameter selection is performed using a multi-variable iterative search routine which seeks to minimize the theoretical mean-squared estimation error. Theoretical Kalman filter estimation error bias and variance values are derived at steady-state operating conditions, and the tuner selection routine is applied to minimize these values. The new methodology yields an improvement in on-line engine performance estimation accuracy.

Simon, Donald L.↗

Digital Filter Separates Signal From Noise

Variance of signal-estimation error minimized. Mathematical technique extracts best estimates of signal component from periodic digital samples of signal plus noise. Technique combines Kalman- and smoothingfilter algorithms to minimize mean-square estimation error based on past, present, and predicted samples of signal plus noise. Technique useful in image analysis and other applications involving processing of noisy signals.

Lear, W. M.↗

Modeling radiation forces acting on TOPEX/Poseidon for precision orbit determination

Geodetic satellites such as GEOSAT, SPOT, ERS-1, and TOPEX/Poseidon require accurate orbital computations to support the scientific data they collect. Until recently, gravity field mismodeling was the major source of error in precise orbit definition. However, albedo and infrared re-radiation, and spacecraft thermal imbalances produce in combination no more than a 6-cm radial root-mean-square (RMS) error over a 10-day period. This requires the development of nonconservative force models that take the satellite's complex geometry, attitude, and surface properties into account. For TOPEX/Poseidon, a 'box-wing' satellite form was investigated that models the satellite as a combination of flat plates arranged in a box shape with a connected solar array. The nonconservative forces acting on each of the eight surfaces are computed independently, yielding vector accelerations which are summed to compute the total aggregate effect on the satellite center-of-mass. In order to test the validity of this concept, 'micro-models' based on finite element analysis of TOPEX/Poseidon were used to generate acceleration histories in a wide variety of orbit orientations. These profiles are then compared to the box-wing model. The results of these simulations and their implication on the ability to precisely model the TOPEX/Poseidon orbit are discussed.

Marshall, J. A.↗

Precision orbit determination for TOPEX/POSEIDON

The TOPEX/POSEIDON mission objective requires that the radial position of the spacecraft be determined with an accuracy better than 13 cm RMS (root mean square). This stringent requirement is an order of magnitude below the accuracy achieved for any altimeter mission prior to the definition of the TOPEX/POSEIDON mission. To satislfy this objective, the TOPEX Precision Orbit determination (POD) Team was established as a joint effort between the NASA Goddard Space Flight Center and the University of Texas at Austin, with collaboration from the University of Colorado and the Jet Propulsion Laboratory. During the prelaunch development and the post launch verification phases, the POD team improved, calibrated, and validated the precision orbit determination computer software systems. The accomplishments include (1) increased accuracy of the gravity and surface force models and (2) improved peformance of both laser ranging and Doppler tracking systems. The result of these efforts led to orbit accuracies for TOPEX/POSEIDON which are significantly better than the original mission requirement. Tests based on data fits, covariance analysis, and orbit comparisons indicate that the radial component of the TOPEX/POSEIDON spacecraft is determined, relative to the Earth's mass center, with an root mean square (RMS) error in the range of 3 to 4 cm RMS. This orbit accuracy, together with the near continuous dual-frequency altimetry from this mission, provides the means to determine the ocean's dynamic topography with an unprecedented accuracy.

Tapley, B. D.↗

Electromagnetic guided couch and multileaf collimator tracking on a TrueBeam accelerator

Purpose: Couch and MLC tracking are two promising methods for real-time motion compensation during radiation therapy. So far, couch and MLC tracking experiments have mainly been performed by different research groups, and no direct comparison of couch and MLC tracking of volumetric modulated arc therapy (VMAT) plans has been published. The Varian TrueBeam 2.0 accelerator includes a prototype tracking system with selectable couch or MLC compensation. This study provides a direct comparison of the two tracking types with an otherwise identical setup. Methods: Several experiments were performed to characterize the geometric and dosimetric performance of electromagnetic guided couch and MLC tracking on a TrueBeam accelerator equipped with a Millennium MLC. The tracking system latency was determined without motion prediction as the time lag between sinusoidal target motion and the compensating motion of the couch or MLC as recorded by continuous MV portal imaging. The geometric and dosimetric tracking accuracies were measured in tracking experiments with motion phantoms that reproduced four prostate and four lung tumor trajectories. The geometric tracking error in beam’s eye view was determined as the distance between an embedded gold marker and a circular MLC aperture in continuous MV images. The dosimetric tracking error was quantified as the measured 2%/2 mm gamma failure rate of a low and a high modulation VMAT plan delivered with the eight motion trajectories using a static dose distribution as reference. Results: The MLC tracking latency was approximately 146 ms for all sinusoidal period lengths while the couch tracking latency increased from 187 to 246 ms with decreasing period length due to limitations in the couch acceleration. The mean root-mean-square geometric error was 0.80 mm (couch tracking), 0.52 mm (MLC tracking), and 2.75 mm (no tracking) parallel to the MLC leaves and 0.66 mm (couch), 1.14 mm (MLC), and 2.41 mm (no tracking) perpendicular to the leaves. The motion-induced gamma failure rate was in mean 0.1% (couch tracking), 8.1% (MLC tracking), and 30.4% (no tracking) for prostate motion and 2.9% (couch), 2.4% (MLC), and 41.2% (no tracking) for lung tumor motion. The residual tracking errors were mainly caused by inadequate adaptation to fast lung tumor motion for couch tracking and to prostate motion perpendicular to the MLC leaves for MLC tracking. Conclusions: Couch and MLC tracking markedly improved the geometric and dosimetric accuracies of VMAT delivery. However, the two tracking types have different strengths and weaknesses. While couch tracking can correct perfectly for slowly moving targets such as the prostate, MLC tracking may have considerably larger dose errors for persistent target shift perpendicular to the MLC leaves. Advantages of MLC tracking include faster dynamics with better adaptation to fast moving targets, the avoidance of moving the patient, and the potential to track target rotations and deformations.

60 APPLIED LIFE SCIENCES↗