Search NASA⌕ Search

SEARCH · Search NASA

Results for “sharp transition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

Strongly adhesive dry transfer technique for van der Waals heterostructure

That one can stack van der Waals materials with atomically sharp interfaces has provided a new material platform of constructing heterostructures. The technical challenge of mechanical stacking is picking up the exfoliated atomically thin materials after mechanical exfoliation without chemical and mechanical degradation. Chemically inert hexagonal boron nitride (hBN) has been widely used for encapsulating and picking up vdW materials. However, due to the relatively weak adhesion of hBN, assembling vdW heterostructures based on hBN has been limited. Here, we report a new dry transfer technique. We used two vdW semiconductors (ZnPS 3 and CrPS 4 ) to pick up and encapsulate layers for vdW heterostructures, which otherwise are known to be hard to fabricate. By combining with optimized polycaprolactone (PCL) providing strong adhesion, we demonstrated various vertical heterostructure devices, including quasi-2D superconducting NbSe 2 Josephson junctions with atomically clean interface. The versatility of the PCL-based vdW stacking method provides a new route for assembling complex 2D vdW materials without interfacial degradation.

36 MATERIALS SCIENCE↗

THE LIGHT CURVE OF THE WEAKLY ACCRETING T TAURI BINARY KH 15D FROM 2005-2010: INSIGHTS INTO THE NATURE OF ITS PROTOPLANETARY DISK

Photometry of the unique pre-main-sequence binary system KH 15D is presented, spanning the years 2005-2010. This system has exhibited photometric variations and eclipses over the last {approx}50 years that are attributed to the effect of a precessing circumbinary disk. Advancement of the occulting edge across the projection on the sky of the binary orbit has continued and the photospheres of both stars are now completely obscured at all times. The system has thus transitioned to a state in which it should be visible only by scattered light, and yet it continues to show a periodic variation on the orbital cycle with an amplitude exceeding 2 mag. This variation, which depends only on the binary phase and not on the height of either star above or below the occulting edge, has likely been present in the data since at least 1995. It can, by itself, account for the 'shoulders' on the light curve prior to ingress and following egress, obviating to some degree the need for components of extant models such as a scattering halo around star A or forward scattering from a fuzzy disk edge. However, the spectroscopic evidence for some direct or forward scattered light from star A even when it was several stellar radii below the occulting edge shows that these components can probably not be fully removed, and raises the possibility that the occulting edge is currently more opaque than it was a decade ago, when the spectra were obtained. A plausible source for the variable scattering component is reflected light from the far side of a warped occulting disk. We have detected color changes in V - I of several tenths of a magnitude to both the blue and red that occur during times of minima. These may indicate the presence of a third source of light (faint star) within the system or a change in the reflectance properties of the disk as the portion being illuminated varies with the orbital motion of the stars. The data support a picture of the circumbinary disk as a geometrically thin, optically thick layer of perhaps millimeter- or centimeter-sized particles that has been sculpted by the binary stars and possibly other components into a decidedly nonplanar configuration. A simple (infinitely sharp) knife-edge model does a good job of accounting for all of the recent (2005-2010) occultation data when one allows for the scattered light component, the spottedness of star A, and variations from cycle to cycle in the location of the edge at the level of 0.1-0.2 stellar diameters.

79 ASTRONOMY AND ASTROPHYSICS↗

Improved heavy-duty vehicle fuel efficiency in India, benefits, costs and environmental impacts

The main objectives of this analysis are to examine the benefits and costs of fuel-saving technologies for new heavy-duty vehicles (HDVs) in India over the next 10 years and, to explore how various scenarios for the deployment of vehicles with these technologies will impact petroleum consumption and carbon dioxide (CO 2 ) emissions over the next three decades. The study team developed simulation models for three representative HDV types—a 40-tonne tractor-trailer, 25-tonne rigid truck, and 16-tonne transit bus—based on top-selling vehicle models in the Indian market. The baseline technology profiles for all three vehicles were developed using India-specific engine data and vehicle specification information from manufacturer literature and input from industry experts. For each of the three vehicles we developed a comprehensive set of seven efficiency technology packages drawing from five major areas: engine, transmission and driveline, tires, aerodynamics, and weight reduction. Our analysis finds that India has substantial opportunity to improve HDV fuel efficiency levels using cost-effective technologies. Results from our simulation modeling of three representative HDV types—a tractor-trailer, rigid truck, and transit bus—reveal that per-vehicle fuel consumption reductions between roughly 20% and 35% are possible with technologies that provide a return on the initial capital investment within 1 to 2 years. Though most of these technologies are currently unavailable in India, experiences in other more advanced markets such as the US and EU suggest that with sufficient incentives and robust regulatory design, significant progress can be made in developing and deploying efficiency technologies that can provide real-world fuel savings for new commercial vehicles in India over the next 10 years. Bringing HDVs in India up to world-class technology levels will yield substantial petroleum and GHG reductions. By 2030, the fuel and CO2 reductions of the scenarios range from 10% to 34%, and at the end of 2050, these reductions grow to 13% and 41%. If we constrain the analysis to select the most efficient technology package that provides the fleets with payback times of 3 years or less, there are annual fleet-wide savings of roughly 11 MTOE of diesel and 34 MMT of CO 2 in 2030, and this grows to 31 MTOE and 97 MMT by 2050.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Femtosecond X-ray Diffraction of Laser-shocked Forsterite (Mg 2 SiO 4 ) to 122 GPa

The response of forsterite, Mg 2 SiO 4 , under dynamic compression is of fundamental importance for understanding its phase transformations and high-pressure behavior. Here, we have carried out an in situ X-ray diffraction study of laser-shocked polycrystalline and single-crystal forsterite from 19 to 122 GPa using the Matter in Extreme Conditions end-station of the Linac Coherent Light Source. Under laser-based shock loading, forsterite does not transform to the high-pressure equilibrium assemblage of MgSiO 3 bridgmanite and MgO periclase, as has been suggested previously. Instead, we observe forsterite and forsterite III, a metastable polymorph of Mg 2 SiO 4 , coexisting in a mixed-phase region from 33 to 75 GPa for both polycrystalline and single-crystal samples. Densities inferred from X-ray diffraction are consistent with earlier gas-gun shock data. At higher stress, the response is sample-dependent. Polycrystalline samples undergo amorphization above 79 GPa. For [010]- and [001]-oriented crystals, a mixture of crystalline and amorphous material is observed to 108 GPa, whereas the [100]-oriented forsterite adopts an unknown phase at 122 GPa. The first two sharp diffraction peaks of amorphous Mg 2 SiO 4 show a similar trend with compression as those observed for MgSiO 3 in both recent static- and laser-driven shock experiments. This study provides new insight into the transformation of forsterite under nanosecond-duration shock loading. This work emphasizes the importance of formation of metastable phases along the Hugoniot and adds to evidence that the 300-K single-crystal diamond anvil cell experiments have relevance for understanding structures formed under shock compression. In particular, the metastable phase forsterite III has now been shown to form under dynamic compression from 10s to 100s of nanoseconds as well as under 300-K static compression. Upon compression to higher pressures, Mg 2 SiO 4 transforms to an amorphous phase. These results have broad relevance for understanding the behavior of silicates under dynamic compression.

36 MATERIALS SCIENCE↗

The Primordial Inflation Polarization Explorer (PIPER)

The Primordial Inflation Polarization Explorer (PIPER) is it balloon-borne instrument designed to search for the faint signature of inflation in the polarized component of the cosmic microwave background (C-N-113). Each flight will be configured for a single frequency, but in order to aid in the removal of the polarized foreground signal due to Galactic dust, the filters will be changed between flights. In this way, the CMB polarization at a total of four different frequencies (200, 270, 350, and 600 GHz) will be, measured on large angular scales. PIPER consists of a pair of cryogenic telescopes, one for measuring each of Stokes Q and U in the instrument frame. Each telescope receives both linear orthogonal polarizations in two 32 x 40 element planar arrays that utilize Transition-Edge Sensors (TES). The first element in each telescope is a variable-delay polarization modulator (VPM) that fully modulates the linear Stokes parameter to which the telescope is sensitive. There are several advantages to this architecture. First, by modulating at the front of the optics, instrumental polarization is unmodulated and is therefore cleanly separated from source polarization. Second, by implementing this system with the appropriate symmetry, systematic effects can be further mitigated. In the PIPER design, many of the. systematics are manifest in the unmeasured linear Stokes parameter for each telescope and this can be separated from the desired signal. Finally, the modulation cycle never mixes the Q and U linear Stokes parameters, and thus residuals in the modulation do not twist the observed polarization vector. This is advantageous because measuring the angle of linear polarization is critical for separating the inflationary signal from other polarized components.

Chuss, David T.↗

Fluid-Thermal-Structural Interactions in Ramp-Induced Shock-Wave Boundary-Layer Interactions at Mach6

Shock-wave boundary-layer interactions (SWBLI) pose unique challenges for the slender airframes and sharp control surfaces characteristic of high-speed airbreathing aircraft. Spikes in pressure and thermal loading have been shown to occur in SWBLI regions; thus, predicting their location and behavior proves critical for assuring aircraft structural integrity and fatigue resilience. SWBLIs frequently lead to severe turbulent boundary-layer separation and corresponding unsteady motions characterized by a wide range of frequencies. Low-frequency motion has been shown to couple with the structure of a compliant panel, and turbulent boundary layers thus present a particular danger for thin control surfaces. Previous studies have shown that the thermal loading on a compliant panel in a ramp-induced SWBLI may have a signi cant impact on the panel vibrations. A multitude of studies has investigated the heating on rigid structures, but a charactrization of the heating effects on compliant structures is necessary to fully understand the fluid-thermal-structural interactions (FTSI) occurring in ramp-induced SWBLIs. This studuses infrared thermography and high-frequency Kulite pressure transducers to examine the heating loads on rigid and compliant ramps at various angles and flow conditions at Mach 6.

Hypersonic↗

Surveying Clay Mineral Diversity in the Murray Formation, Gale Crater, Mars

The CheMin XRD instrument aboard Mars Science Laboratory (MSL) has documented clay minerals in various drill samples during its traverse of Gale Crater's floor and ascent of Mt. Sharp. The most recent samples, named Marimba, Quela and Sebina were acquired from the Murray Formation in the Murray Buttes region of lower Mt. Sharp. Marimba and Quela come from a approx. 30 m package of finely laminated lacustrine mudstones. Sebina comes from an overlying package of heterolithic mudstone-sandstones. Clay minerals make up approx.15-25 wt.% of the bulk rock with similar contributions to XRD patterns in all three samples. Broad basal reflections at approx. 10deg 2(theta) CoK(alpha) indicate the presence of 2:1 group clay minerals. The 02(lambda) clay mineral band lies at approx. 22.9deg 2(theta), a region typically occupied by Fe-bearing dioctahedral 2:1 clay minerals like nontronite or Fe-illite. The low humidity within the CheMin instrument, which is open to the martian atmosphere, promotes loss of interlayer H2O and collapse of smectite interlayers making them difficult to distinguish from illites. However, based on the low K content of the bulk samples, it appears that smectitic clay minerals are dominant. Peak dehydroxylation of the Marimba sample measured by the SAM instrument on MSL occurred at 610C and 780C. Fe-bearing smectites are not consistent with these dehydroxylation temperatures. Thus, we suggest that a mixture of dioctahedral and trioctahedral smectite phases are present giving the appearance of intermediate octahedral occupancy in XRD. Dioctahedral smectites have not previously been reported in Gale Crater by MSL. Earlier in the mission, relatively clay mineral rich samples (approx. 20 wt.%) from lacustrine mudstones in Yellowknife Bay (YKB) were found to contain ferrian saponites. It is proposed that YKB saponites formed via isochemical aqueous alteration of detrital olivine close to the time of sediment deposition, under anoxic to poorly oxidizing conditions. In terrestrial settings where alteration sequences of basaltic rocks or sediments are observed, first-stage alteration clay minerals are typically trioctahedral smectite species, as reported from YKB. In later alteration stages trioctahedral clay minerals are replaced by dioctahedral clays as a result of removal and/or oxidation of Fe2+ and Mg. Observed changes in clay mineralogy between YKB and Murray Buttes samples correspond with differences in bulk mineralogy, including: 1) a transition from magnetite to hematite as the main Fe-oxide, 2) increasing abundances of Ca-sulfates and 3) a reduction in the quantity of reactive mafic minerals. This mineralogical change indicates an increasing degree of aqueous alteration and oxidation of mafic detritus in the upper part of the Murray Formation. These results broaden the spectrum of mineralogical facies documented by MSL. Together sedimentology and mineralogy indicate a long-lasting, dynamic fluvial-lacustrine system encompassing a range aqueous geochemical processes under varying redox conditions. Future work is needed to unravel the influence of global and local controls on the range of ancient conditions observed at Gale Crater.

MSL↗

Fluid-Thermal-Structural Interactions in Ramp-Induced Shock-Wave Boundary-Layer Interactions at Mach 6

Shock-wave boundary-layer interactions (SWBLI) pose unique challenges for the slender airframes and sharp control surfaces characteristic of high-speed airbreathing aircraft. Spikes in pressure and thermal loading have been shown to occur in SWBLI regions; thus, predicting their location and behavior proves critical for assuring aircraft structural integrity and fatigue resilience. SWBLIs frequently lead to severe turbulent boundary-layer separation and corresponding unsteady motions characterized by a wide range of frequencies. Low-frequency motion has been shown to couple with the structure of a compliant panel, and turbulent boundary layers thus present a particular danger for thin control surfaces. Previous studies have shown that the thermal loading on a compliant panel in a ramp-induced SWBLI may have a signi cant impact on the panel vibrations. A multitude of studies has investigated the heating on rigid structures, but a charactrization of the heating effects on compliant structures is necessary to fully understand the fluid-thermal-structural interactions (FTSI) occurring in ramp-induced SWBLIs. This studuses infrared thermography and high-frequency Kulite pressure transducers to examine the heating loads on rigid and compliant ramps at various angles and flow conditions at Mach 6.

Hypersonic↗

Review of lattice results concerning low-energy particle physics: Flavour Lattice Averaging Group (FLAG)

We review lattice results related to pion, kaon, D- and B-meson physics with the aim of making them easily accessible to the particle-physics community. More specifically, we report on the determination of the light-quark masses, the form factor f + (0), arising in the semileptonic K → π transition at zero momentum transfer, as well as the decay constant ratio f K /f π and its consequences for the CKM matrix elements V us and V ud . Furthermore, we describe the results obtained on the lattice for some of the low-energy constants of SU(2) L × SU(2) R and SU(3) L × SU(3) R Chiral Perturbation Theory. We review the determination of the B K parameter of neutral kaon mixing as well as the additional four B parameters that arise in theories of physics beyond the Standard Model. The latter quantities are an addition compared to the previous review. For the heavy-quark sector, we provide results for m c and m b (also new compared to the previous review), as well as those for D- and B-meson-decay constants, form factors, and mixing parameters. These are the heavy-quark quantities most relevant for the determination of CKM matrix elements and the global CKM unitarity-triangle fit. Finally, we review the status of lattice determinations of the strong coupling constant α s .

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

LDAR, A Three-Dimensional Lightning Warning System: Its Development and Use by the Government, and Transition to Public Availability

NASA, at the John F. Kennedy Space Center (KSC), developed and operates a unique high precision lightning location system to provide lightning related weather warnings. These warnings are used to stop lightning-sensitive operations such as space vehicle launches and ground operations where equipment and personnel are at risk. The data is provided to the Range Weather Operations [45th Weather Squadron, U. S. Air Force (USAF)] where it is used with other meteorological data to issue weather advisories and warnings for Cape Canaveral Air Station (CCAS) and KSC operations. This system, called Lightning Detection and Ranging (LDAR), provides users with a graphical display in three dimensions of 66 MHz radio frequency events generated by lightning processes. The locations of these events provide a sound basis for the prediction of lightning hazards. NASA and Global Atmospherics, Inc. are developing a new system that will replace the unique LDAR components with commercially available and maintainable components having improved capabilities. These components will be phased in to ensure full continuity and access to this important warning technology. These LDAR systems are expected to eventually be available for installation and use by the public at specialized facilities, such as airports, and for general weather warnings via the National Weather Service (NWS) or television broadcast. The NWS in Melbourne has had access to real-time LDAR data since 1993 on an experimental basis. This use of LDAR has shown promise for the improvement of aviation forecasts and severe weather warnings. More so, it has opened the door to investigate the feasibility of issuing lightning-related public advisories. The success of its early use suggests that this technology may improve safety and potentially save lives, therefore constituting a significant benefit to the public. This paper describes the LDR system, the plans and progress of these upgrades, and the potential benefits of its use.

Starr, Stan↗

Development and Validation of a Lifecycle-based Prognostics Architecture with Test Bed Validation

On-line monitoring and tracking of nuclear plant system and component degradation is being investigated as a method for improving the safety, reliability, and maintainability of aging nuclear power plants. Accurate prediction of the current degradation state of system components and structures is important for accurate estimates of their remaining useful life (RUL). The correct quantification and propagation of both the measurement uncertainty and model uncertainty is necessary for quantifying the uncertainty of the RUL prediction. This research project developed and validated methods to perform RUL estimation throughout the lifecycle of plant components. Prognostic methods should seamlessly operate from beginning of component life (BOL) to end of component life (EOL). We term this "Lifecycle Prognostics." When a component is put into use, the only information available may be past failure times of similar components used in similar conditions, and the predicted failure distribution can be estimated with reliability methods such as Weibull Analysis (Type I Prognostics). As the component operates, it begins to degrade and consume its available life. This life consumption may be a function of system stresses, and the failure distribution should be updated to account for the system operational stress levels (Type II Prognostics). When degradation becomes apparent, this information can be used to again improve the RUL estimate (Type III Prognostics). This research focused on developing prognostics algorithms for the three types of prognostics, developing uncertainty quantification methods for each of the algorithms, and, most importantly, developing a framework using Bayesian methods to transition between prognostic model types and update failure distribution estimates as new information becomes available. The developed methods were then validated on a range of accelerated degradation test beds. The ultimate goal of prognostics is to provide an accurate assessment for RUL predictions, with as little uncertainty as possible. From a reliability and maintenance standpoint, there would be improved safety by avoiding all failures. Calculated risk would decrease, saving money by avoiding unnecessary maintenance. One major bottleneck for data-driven prognostics is the availability of run-to-failure degradation data. Without enough degradation data leading to failure, prognostic models can yield RUL distributions with large uncertainty or mathematically unsound predictions. To address these issues a "Lifecycle Prognostics" method was developed to create RUL distributions from Beginning of Life (BOL) to End of Life (EOL). This employs established Type I, II, and III prognostic methods, and Bayesian transitioning between each Type. Bayesian methods, as opposed to classical frequency statistics, show how an expected value, a priori, changes with new data to form a posterior distribution. For example, when you purchase a component you have a prior belief, or estimation, of how long it will operate before failing. As you operate it, you may collect information related to its condition that will allow you to update your estimated failure time. Bayesian methods are best used when limited data are available. The use of a prior also means that information is conserved when new data are available. The weightings of the prior belief and information contained in the sampled data are dependent on the variance (uncertainty) of the prior, the variance (uncertainty) of the data, and the amount of measured data (number of samples). If the variance of the prior is small compared to the uncertainty of the data, the prior will be weighed more heavily. However, as more data are collected, the data will be weighted more heavily and will eventually swamp out the prior in calculating the posterior distribution of model parameters. Fundamentally Bayesian analysis updates a prior belief with new data to get a posterior belief. The general approach to applying the Bayesian method to lifecycle prognostics consisted of identifying the prior, which is the RUL estimate and uncertainty from the previous prognostics type, and combining it with observational data related to the newer prognostics type. The resulting lifecycle prognostics algorithm uses all available information throughout the component lifecycle.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

FLAG Review 2019: Flavour Lattice Averaging Group (FLAG)

Abstract We review lattice results related to pion, kaon, D -meson, B -meson, and nucleon physics with the aim of making them easily accessible to the nuclear and particle physics communities. More specifically, we report on the determination of the light-quark masses, the form factor $$f_+(0)$$ f + ( 0 ) arising in the semileptonic $$K \rightarrow \pi $$ K → π transition at zero momentum transfer, as well as the decay constant ratio $$f_K/f_\pi $$ f K / f π and its consequences for the CKM matrix elements $$V_{us}$$ V us and $$V_{ud}$$ V ud . Furthermore, we describe the results obtained on the lattice for some of the low-energy constants of $$SU(2)_L\times SU(2)_R$$ S U ( 2 ) L × S U ( 2 ) R and $$SU(3)_L\times SU(3)_R$$ S U ( 3 ) L × S U ( 3 ) R Chiral Perturbation Theory. We review the determination of the $$B_K$$ B K parameter of neutral kaon mixing as well as the additional four B parameters that arise in theories of physics beyond the Standard Model. For the heavy-quark sector, we provide results for $$m_c$$ m c and $$m_b$$ m b as well as those for D - and B -meson decay constants, form factors, and mixing parameters. These are the heavy-quark quantities most relevant for the determination of CKM matrix elements and the global CKM unitarity-triangle fit. We review the status of lattice determinations of the strong coupling constant $$\alpha _s$$ α s . Finally, in this review we have added a new section reviewing results for nucleon matrix elements of the axial, scalar and tensor bilinears, both isovector and flavor diagonal.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Dielectric and ferroelectric response of compositionally graded bilayer and trilayer composites of BaTiO{sub 3} and 0.975BaTiO{sub 3}-0.025Ba(Cu{sub 1/3}Nb{sub 2/3})O{sub 3}

In this paper, we report the dielectric and ferroelectric response of compositionally graded bilayer and trilayer composites consisting of BaTiO{sub 3} (BT) and 0.975BaTiO{sub 3}-0.025Ba(Cu{sub 1/3}Nb{sub 2/3})O{sub 3} (BTBCN). Two types of graded bilayer samples were synthesized, one with same thickness of BT and BTBCN while other with different layer thicknesses. The graded trilayer sample consisted of BT layer sandwiched between two BTBCN layers of equal thickness. Scanning electron microscopy and transmission electron microscopy images showed a sharp interface with needle-shape domains across the interface. The domain size on BT side was found to be larger than that on BTBCN side. The temperature dependence of dielectric response for all composite systems was found to exhibit shifting in characteristic Curie peak compared to constituent material which was associated to coupling between layers. Moreover, the differences in grain size, tetragonality, domain mobility of each layer was found to perturb the electrical response of composite. The polarization mismatch between uncoupled BT and BTBCN established internal electric field in composite specimen and defined new polarization states in each layer by perturbing free energy functional of the composite specimen. Dynamic hysteresis behaviors and power-law scaling relations of all specimens were determined from polarization-electric field hysteresis loop measurements as a function of frequency. All systems were found to exhibit similar dynamic scaling relationships. Hysteresis area <A>, P{sub r}, and E{sub C} decreased with increasing frequency due to delayed response but increased with increasing applied electric field due to enhancement of driving force. Trilayer system was found to exhibit strong internal-bias field and double hysteresis behavior. The coupling effect resulting due to polarization mismatch between layers had substantial influence on the dynamic hysteresis behavior and power-law scaling relations.

36 MATERIALS SCIENCE↗

The Transition of High-Resolution NASA MODIS Sea Surface Temperatures into the WRF Environmental Modeling System

The NASA Short-term Prediction Research and Transition (SPoRT) Center has developed a Moderate Resolution Imaging Spectroradiometer (MODIS) sea surface temperature (SST) composite at 2-km resolution that has been implemented in version 3 of the National Weather Service (NWS) Weather Research and Forecasting (WRF) Environmental Modeling System (EMS). The WRF EMS is a complete, full physics numerical weather prediction package that incorporates dynamical cores from both the Advanced Research WRF (ARW) and the Non-hydrostatic Mesoscale Model (NMM). The installation, configuration, and execution of either the ARW or NMM models is greatly simplified by the WRF EMS to encourage its use by NWS Weather Forecast Offices (WFOs) and the university community. The WRF EMS is easy to run on most Linux workstations and clusters without the need for compilers. Version 3 of the WRF EMS contains the most recent public release of the WRF-NMM and ARW modeling system (version 3 of the ARW is described in Skamarock et al. 2008), the WRF Pre-processing System (WPS) utilities, and the WRF Post-Processing program. The system is developed and maintained by the NWS National Science Operations Officer Science and Training Resource Coordinator. To initialize the WRF EMS with high-resolution MODIS SSTs, SPoRT developed the composite product consisting of MODIS SSTs over oceans and large lakes with the NCEP Real-Time Global (RTG) filling data over land points. Filling the land points is required due to minor inconsistencies between the WRF land-sea mask and that used to generate the MODIS SST composites. This methodology ensures a continuous field that adequately initializes all appropriate arrays in WRF. MODIS composites covering the Gulf of Mexico, western Atlantic Ocean and the Caribbean are generated daily at 0400, 0700, 1600, and 1900 UTC corresponding to overpass times of the NASA Aqua and Terra polar orbiting satellites. The MODIS SST product is output in gridded binary-1 (GRIB-1) data format for a seamless incorporation into WRF via the WPS utilities. The full-resolution, 1-km MODIS product is sub-sampled to 2-km grid spacing due to limitations in handling very large dimensions in the GRIB-1 data format. The GRIB-1 files are posted online at ftp://ftp.nsstc.org/sstcomp/WRF/, which is directly accessed by the WRF EMS scripts. The MODIS SST composites are also downloaded to the EMS data server, which is accessible by the WRF EMS users and NWS WFOs. The SPoRT MODIS SST composite provides the model with superior detail of the ocean gradients around Florida and surrounding waters, whereas the operational RTG SST typically depicts a relatively smooth field and is not able to capture sharp horizontal gradients in SST. Differences of 2-3 C are common over small horizontal distances, leading to enhanced SST gradients on either side of the Gulf Stream and along the edges of the cooler shelf waters. These sharper gradients can in turn produce atmospheric responses in simulated temperature and wind fields as depicted in LaCasse et al. Differences in atmospheric verification statistics over a several month study were generally small in the vicinity of south Florida; however, the validation of SSTs at specific buoy locations revealed important improvements in the biases and RMS errors, especially in the vicinity of the cooler shelf waters off the east-central Florida coast. A current weakness in the MODIS SST product is the occurrence of occasional discontinuities caused by high latency in SST coverage due to persistent cloud cover. An enhanced method developed by Jedlovec et al. (2009, GHRSST User Symposium) reduces the occurrence of these problems by adding Advanced Microwave Scanning Radiometer -- EOS (AMSR-E) SST data to the compositing process. Enhanced SST composites are produced over the ocean regions surrounding the Continental U.S. at four times each day corresponding to Terra and Aqua equator crossing times. For a given day and overpass time, both MODInd AMSR-E data from the previous seven days form a collection used in the compositing. At each MODIS pixel, cloud-free SST values from the collection are used to form a weighted average based on their latency (number of days from the current day). In this way, recent SST data are given more weight than older data. One of the primary issues involved in incorporating the AMSR-E microwave data in the composites is the tradeoff between the decreased spatial resolution of the AMSR-E data (25 km) and the increased coverage due to its near all-weather capability. Currently, the AMSR-E is given a weight of 20% compared to MODIS data, thereby preserving the spatial structure observed in the MODIS data. Day-time (night-time) AMSR-E SST data from Aqua are used with both Terra and Aqua MODIS day-time (night-time) SST data sets.

Case, Jonathan L.↗

FLAG Review 2021

Abstract We review lattice results related to pion, kaon, D -meson, B -meson, and nucleon physics with the aim of making them easily accessible to the nuclear and particle physics communities. More specifically, we report on the determination of the light-quark masses, the form factor $$f_+(0)$$ f + ( 0 ) arising in the semileptonic $$K \rightarrow \pi $$ K → π transition at zero momentum transfer, as well as the decay constant ratio $$f_K/f_\pi $$ f K / f π and its consequences for the CKM matrix elements $$V_{us}$$ V us and $$V_{ud}$$ V ud . Furthermore, we describe the results obtained on the lattice for some of the low-energy constants of $$SU(2)_L\times SU(2)_R$$ S U ( 2 ) L × S U ( 2 ) R and $$SU(3)_L\times SU(3)_R$$ S U ( 3 ) L × S U ( 3 ) R Chiral Perturbation Theory. We review the determination of the $$B_K$$ B K parameter of neutral kaon mixing as well as the additional four B parameters that arise in theories of physics beyond the Standard Model. For the heavy-quark sector, we provide results for $$m_c$$ m c and $$m_b$$ m b as well as those for the decay constants, form factors, and mixing parameters of charmed and bottom mesons and baryons. These are the heavy-quark quantities most relevant for the determination of CKM matrix elements and the global CKM unitarity-triangle fit. We review the status of lattice determinations of the strong coupling constant $$\alpha _s$$ α s . We consider nucleon matrix elements, and review the determinations of the axial, scalar and tensor bilinears, both isovector and flavor diagonal. Finally, in this review we have added a new section reviewing determinations of scale-setting quantities.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Selectivity in Yttrium Manganese Oxide Synthesis via Local Chemical Potentials in Hyperdimensional Phase Space

In sharp contrast to molecular synthesis, materials synthesis is generally presumed to lack selectivity. The few known methods of designing selectivity in solid-state reactions have limited scope, such as topotactic reactions or strain stabilization. This contribution describes a general approach for searching large chemical spaces to identify selective reactions. This novel approach explains the ability of a nominally “innocent” Na 2 CO 3 precursor to enable the metathesis synthesis of single-phase Y 2 Mn 2 O 7 : an outcome that was previously only accomplished at extreme pressures and which cannot be achieved with closely related precursors of Li 2 CO 3 and K 2 CO 3 under identical conditions. By calculating the required change in chemical potential across all possible reactant-product interfaces in an expanded chemical space including Y, Mn, O, alkali metals, and halogens, using thermodynamic parameters obtained from density functional theory calculations, we identify reactions that minimize the thermodynamic competition from intermediates. In this manner, only the Na-based intermediates minimize the distance in the hyperdimensional chemical potential space to Y 2 Mn 2 O 7 , thus providing selective access to a phase which was previously thought to be metastable. Experimental evidence validating this mechanism for pathway-dependent selectivity is provided by intermediates identified from in situ synchrotron-based crystallographic analysis. Finally, this approach of calculating chemical potential distances in hyperdimensional compositional spaces provides a general method for designing selective solid-state syntheses that will be useful for gaining access to metastable phases and for identifying reaction pathways that can reduce the synthesis temperature, and cost, of technological materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Predicting the Atmospheric Composition of Extrasolar Giant Planets

To date, approximately 120 planet-sized objects have been discovered around other stars, mostly through the radial-velocity technique. This technique can provide information about a planet s minimum mass and its orbital period and distance; however, few other planetary data can be obtained at this point in time unless we are fortunate enough to find an extrasolar giant planet that transits its parent star (i.e., the orbit is edge-on as seen from Earth). In that situation, many physical properties of the planet and its parent star can be determined, including some compositional information. Our prospects of directly obtaining spectra from extrasolar planets may improve in the near future, through missions like NASA's Terrestrial Planet Finder. Most of the extrasolar giant planets (EGPs) discovered so far have masses equal to or greater than Jupiter's mass, and roughly 16% have orbital radii less than 0.1 AU - extremely close to the parent star by our own Solar-System standards (note that Mercury is located at a mean distance of 0.39 AU and Jupiter at 5.2 AU from the Sun). Although all EGPs are expected to have hydrogen-dominated atmospheres similar to Jupiter, the orbital distance can strongly affect the planet's temperature, physical, chemical, and spectral properties, and the abundance of minor, detectable atmospheric constituents. Thermochemical equilibrium models can provide good zero-order predictions for the atmospheric composition of EGPs. However, both the composition and spectral properties will depend in large part on disequilibrium processes like photochemistry, chemical kinetics, atmospheric transport, and haze formation. We have developed a photochemical kinetics, radiative transfer, and 1-D vertical transport model to study the atmospheric composition of EGPs. The chemical reaction list contains H-, C-, O-, and N-bearing species and is designed to be valid for atmospheric temperatures ranging from 100-3000 K and pressures up to 50 bar. Here we examine the effect of stellar distance (e.g., incident ultraviolet flux, atmospheric temperature) on the chemical properties of EGPs. The model is applied to two generic Class II and III intermediate temperature EGPs located at 3.3 and 0.27 AU from a solar-like parent star, and the results are compared with a model for Jupiter at 5.2 AU.

Sharp, A. G.↗