Search NASA⌕ Search

SEARCH · Search NASA

Results for “Advanced Test Reactor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

Data Compilation for AGR-2 Baseline Coated Particle Batch G73J-14-93072A

Coated particle fuel batch G73J-14-93072A was produced by the Babcock and Wilcox Company (B&W) for possible selection as UCO baseline fuel for the Advanced Gas Reactor Fuel Development and Qualification Program’s AGR-2 irradiation test. Batch G73J-14-93072A is a single batch of TRISO-coated 425 μm nominal diameter 14% low enrichment uranium oxide/uranium carbide kernels (LEUCO). The TRISO-coatings consist of a ~50% dense carbon buffer layer (100 μm nominal thickness) followed by a dense inner pyrocarbon layer (40 μm nominal thickness) followed by a SiC layer (35 μm nominal thickness) followed by another dense outer pryocarbon layer (40 μm nominal thickness). The AGR-2 Fuel Specification (INL SPC-923) provides the requirements necessary for acceptance of the fuel manufactured for the AGR-2 irradiation test. The bulk of the kernels and coated particle acceptance testing was performed at B&W and is not contained in this report. Sample NP-B7940 was sent to ORNL for supplemental characterization. The procedures for the limited characterization and qualification of the particles performed at ORNL are outlined in ORNL product inspection plan AGR-CHAR-PIP-09. The BAFo equivalent optical anisotropies of the inner and outer pyrocarbon layers are reported on Inspection Report Form IRF-09, with a determination as to whether the particle batch satisfied the specified parameters for this property. The batch was found to satisfy the AGR-2 Fuel Specification SPC-923, Rev. 1 for IPyC and OPyC anisotropy. Also provided in this data package are data on the true BAFo, average particle weight, OPyC open porosity, and SiC soot inclusion defect fraction. True BAFo is calculated as (1+N)/(1-N), where N is the diattenuation. This differs from equivalent BAFo = 1+3N, which is the calculation used by the fuel specification to allow comparison to historical measurements. Average OPyC open porosity was determined using a single sample to be 0.62 ml/m 2 . An unusually high SiC soot defect fraction was observed in this sample, mostly due to bands of porosity apparently resulting from a fabrication anomaly in the coating gas delivery system. This is discussed further in the pages following Data Report Form DRF-32.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Data Compilation for AGR-2 Baseline Coated Particle Batch G73J-14-93071A

Coated particle fuel batch G73J-14-93071A was produced by the Babcock and Wilcox Company (B&W) for possible selection as UCO baseline fuel for the Advanced Gas Reactor Fuel Development and Qualification Program’s AGR-2 irradiation test. Batch G73J-14-93071A is a single batch of TRISO-coated 425 µm nominal diameter 14% low enrichment uranium oxide/uranium carbide kernels (LEUCO). The TRISO-coatings consist of a ~50% dense carbon buffer layer (100 µm nominal thickness) followed by a dense inner pyrocarbon layer (40 µm nominal thickness) followed by a SiC layer (35 µm nominal thickness) followed by another dense outer pyrocarbon layer (40 µm nominal thickness). The AGR-2 Fuel Specification (INL SPC-923) provides the requirements necessary for acceptance of the fuel manufactured for the AGR-2 irradiation test. The bulk of the kernels and coated particle acceptance testing was performed at B&W and is not contained in this report. Sample NP-B7927 was sent to ORNL for supplemental characterization. The procedures for the limited characterization and qualification of the particles performed at ORNL are outlined in ORNL product inspection plan AGR-CHAR-PIP-09. The BAFo equivalent optical anisotropies of the inner and outer pyrocarbon layers are reported on Inspection Report Form IRF-09, with a determination as to whether the particle batch satisfied the specified parameters for this property. The batch was found to satisfy the AGR-2 Fuel Specification SPC-923, Rev. 1 for IPyC and OPyC anisotropy. Also provided in this data package are data on the true BAFo, average particle weight, OPyC open porosity, and SiC soot inclusion defect fraction. True BAFo is calculated as (1+N)/(1-N), where N is the diattenuation. This differs from equivalent BAFo = 1+3N, which is the calculation used by the fuel specification to allow comparison to historical measurements. Average OPyC open porosity was determined using a single sample to be 0.65 ml/m². An unusually high SiC soot defect fraction was observed in this sample, apparently due to a fabrication anomaly which resulted in one of the hot sampling cups disturbing the bed fluidization during SiC deposition. This is discussed further in the pages following Data Report Form DRF-32.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Data Compilation for AGR-3/4 Designed-to-Fail (DTF) Fuel Particle Batch LEU03-07DTF

This document is a compilation of coating and characterization data for the designed-to-fail (DTF) fuel particle batch LEU03-07DTF. LEU03-07DTF was fabricated for insertion into fuel compacts designed for the Advanced Gas Reactor Fuel Development and Qualification (AGR) program’s third irradiation test (AGR-3/4). This document also includes coating and characterization data for the associated qualification DTF fuel particle batch, LEU12-03DTF. LEU12-03DTF was fabricated using the same coating parameters as LEU03-07DTF, as a final check on the processing conditions prior to coating the LEU03-07DTF fuel batch.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR-2 Fuel Compacts Information Summary: Prepared for the NRC MELCOR Project

This document was prepared at the request of the NRC to provide summary information on the compacts used in the Department of Energy's Office of Nuclear Energy (DOE-NE) Advanced Gas Reactor Fuel Development and Qualification (AGR) program's second irradiation test, AGR-2. The data is this summary document is being provided to Robert P. Wichner in support of a Nuclear Regulatory Commission (NRC) Methods for Estimation of Leakages and Consequences Of Release (MELCOR) code development effort. The AGR-2 compacts described in this report contained two types of fuel kernels. Uranium oxide (UO 2 ) fuel kernels with a nominal diameter of 500um and mixed uranium oxide/uranium carbide (UCO) fuel kernels with a nominal diameter of 425 um. The fuel kernels were produced by Babcock and Wilcox (B&W) in Lynchburg, Virginia. The UCO kernels were identified as composite G731-14-69307. The UO2 kernels were identified as composite G73AA-10-69308.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Data Compilation for AGR-2 B&W UO2 Coated Particle Batch G73H-10-93085B

Coated particle fuel batch G73H-10-93085B was produced by the Babcock and Wilcox Company (B&W) for use as UO₂ fuel for the Advanced Gas Reactor Fuel Development and Qualification Program’s AGR-2 irradiation test. Batch G73H-10-93085B is a single batch of TRISO-coated 500 μm nominal diameter 10% low enrichment uranium oxide kernels (LEU). The TRISO-coatings consist of a ~50% dense carbon buffer layer (100 μm nominal thickness) followed by a dense inner pyrocarbon layer (40 μm nominal thickness) followed by a SiC layer (35 μm nominal thickness) followed by another dense outer pyrocarbon layer (40 μm nominal thickness). Argon was added to the hydrogen fluidization gas during SiC deposition. The AGR-2 Fuel Specification (INL SPC-923) provides the requirements necessary for acceptance of the fuel manufactured for the AGR-2 irradiation test. The bulk of the kernels and coated particle acceptance testing was performed at B&W and is not contained in this report. B&W samples NP-B8488, NP-B8489, and NP-B8490 (all from batch G73H-10-93085B) were sent to ORNL for characterization and compacting. These samples were composited and renamed LEU10. Samples were then riffled for supplemental characterization. The procedures for the limited characterization and qualification of the particles performed at ORNL are outlined in ORNL product inspection plan AGR-CHAR-PIP-09. The BAFo equivalent optical anisotropies of the inner and outer pyrocarbon layers are reported on Inspection Report Form IRF-09, with a determination as to whether the particle batch satisfied the specified parameters for this property. The batch was found to satisfy the AGR-2 Fuel Specification SPC-923, Rev. 1 for IPyC and OPyC anisotropy. Also provided in this data package are data on the true BAFo, average particle weight, and SiC soot inclusion defect fraction. True BAFo is calculated as (1+N)/(1-N), where N is the diattenuation. This differs from equivalent BAFo = 1+3N, which is the calculation used by the fuel specification to allow comparison to historical measurements. Three SiC inclusions were found in a sample of 3510 particles. This corresponds to a defect fraction of <2.3E-3 at 95% confidence. One of these inclusions was of unusual appearance and was determined to contain molybdenum using energy dispersive x-ray analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Data Compilation for AGR-2 Variant Coated Particle Batch G73J-14-93074A

Coated particle fuel batch G73J-14-93074A was produced by the Babcock and Wilcox Company (B&W) for possible selection as UCO variant fuel for the Advanced Gas Reactor Furl Development and Qualification Program's AGR-2 irradiation test. Batch G73J-14-93074A is a single batch of TRISO-coated 425 μm nominal diameter 14% low enrichment uranium oxide/uranium carbide kernels (LEUCO). The TRISO-coatings consist of a ~50% dense carbon buffer layer (100 μm nominal thickness) followed by a dense inner pyrocarbon layer (40 μm nominal thickness) followed by a SiC layer (35 μm nominal thickness) followed by another dense outer pyrocarbon layer (40 μm nominal thickness). For this variant, argon was added to the hydrogen fluidization gas during SiC deposition. The AGR-2 Fuel Specification (INL SPC-923) provides the requirements necessary for acceptance of the fuel manufactured for the AGR-2 irradiation test. The bulk of the kernels and coated particle acceptance testing was performed at B&W and is not contained in this report. Sample NP-B7979 was sent to ORNL for supplemental characterization. The procedures for the limited characterization and qualification of the particles performed at ORNL are outlined in ORNL product inspection plan AGR-CHAR-PIP-09. The BAFo equivalent optical anisotropies of the inner and outer pyrocarbon layers are reported on Inspection Report Form IRF-09, with a determination as to whether the particle batch satisfied the specified parameters for this property. The batch was found to satisfy the AGR-2 Fuel Specification SPC-923, Rev. 1 for IPyC and OPyC anisotropy. Also provided in this data package are data on the true BAFo, average particle weight, OPyC open porosity, and SiC soot inclusion defect fraction. True BAFo is calculated as (1+N)/(1-N), where N is the diattenuation. This differs from equivalent BAFo = 1+3N, which is the calculation used by the fuel specification to allow comparison to historical measurements. Average OPyC open porosity was determined using a single sample to be 0.27 ml/m². One SiC soot inclusion was found in a sample of 4746 particles. This corresponds to <1E-3 defect fraction at 95% confidence.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Data Compilation for AGR-2 Variant Coated Particle Batch G73J-14-93073A

Coated particle fuel batch G73J-14-93073A was produced by the Babcock and Wilcox Company (B&W) for possible selection as UCO variant fuel for the Advanced Gas Reactor Fuel Development and Qualification Program's AGR-2 irradiation test. Batch G73J-14-93073A is a single batch of TRISO-coated 425 μm nominal diameter 14% low enrichment uranium oxide/uranium carbide kernels (LEUCO). The TRISO-coatings consist of a ~50% dense carbon buffer layer (100 μm nominal thickness) followed by a dense inner pyrocarbon layer (40 μm nominal thickness) followed by a SiC layer (35 μm nominal thickness) followed by another dense outer pyrocarbon layer (40 μm nominal thickness). For this variant, argon was added to the hydrogen fluidization gas during SiC deposition. The AGR-2 Fuel Specification (INL SPC-923) provides the requirements necessary for acceptance of the fuel manufactured for the AGR-2 irradiation test. The bulk of the kernels and coated particle acceptance testing was performed at B&W and is not contained in this report. Sample NP-B7958 was sent to ORNL for supplemental characterization. The procedures for the limited characterization and qualification of the particles performed at ORNL are outlined in ORNL product inspection plan AGR-CHAR-PIP-09. The BAFo equivalent optical anisotropies of the inner and outer pyrocarbon layers are reported on Inspection Report Form IRF-09, with a determination as to whether the particle batch satisfied the specified parameters for this property. The batch was found to satisfy the AGR-2 Fuel Specification SPC-923, Rev. 1 for IPyC and OPyC anisotropy. Also provided in this data package are data on the true BAFo, average particle weight, OPyC open porosity, and SiC soot inclusion defect fraction. True BAFo is calculated as (1+N)/(1-N), where N is the diattenuation. This differs from equivalent BAFo = 1+3N, which is the calculation used by fuel specification to allow comparison to historical measurements. Average OPyC open porosity was determined using a single sample to be 0.41 ml/m². One possible SiC soot inclusion was found in a sample of 4729 particles. This corresponds to <1E-3 defect fraction at 95% confidence.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The Use of Acoustic Cavitation to Recovery High-Assay Low-Enriched Uranium (HALEU) form TRISO Fuel Particles

Recent interest in advanced nuclear reactor concepts such as small modular reactor (SMR), micro reactor or versatile test reactor (VTR) has increased the demand for high-assay, low-enriched uranium (HALEU). The sustainable management of this resource is integral to successful resurgence of nuclear energy in the United States. The High Temperature Gas-Cooled Reactor (HTGR) concept is a prime candidate for deployment of the new fleet of SMRs, and it will become very important to have a simple and cost-effective technology to recover HALEU from short-burned, defective, or off-specification TRISO fuel particles. We have attempted to harness the high energetics of sonochemistry to penetrate the TRISO fuel particles and recover HALEU via acidic leaching. While the TRISO fuel particle design is inherently “bulletproof,” (due to the silicon carbide (SiC) layer), ultrasonic irradiation may hold the key to convenient access to its valuable contents. Sonochemistry is a field of chemistry based on acoustic cavitation, which is the formation, growth, and collapse of bubbles in liquid media.1,2 The oscillating bubble formation is produced by irradiation of a liquid media with sound waves. Literature reports indicate that collapsing bubbles induced by cavitation produces intense local heating, high pressures, and short lifetimes.1 These localized hot spots reach temperatures of ˜5000 K, pressures approaching 500 atm, and heating and cooling rates exceeding 100 K/s.1 The large temperature and pressure differentials deliver high-energy heating and microscopic explosive shock waves to a liquid media or liquid/solid interface. Cavitation at the surface of a solid in solution induces a deformation in the bubble cavity upon collapse. This deformation reinforces the bubble structure and sends a fast-moving stream of liquid through the cavity at the surface with velocities greater than 100 m/s.3 These energetic impacts have demonstrated an ability to penetrate or simply destroy the SiC shell surrounding the uranium fuel kernel during prolonged exposures to the high-power acoustic waves. Some preliminary results demonstrating HALEU recovery using sonochemistry techniques will be reported.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Assessing High Burnup U-19Pu-10Zr Fuel Performance against Historical and Modeled Behavior

Advancing the deployment of sodium-cooled fast reactors (SFRs) requires thorough testing of metallic fuel pins under accident conditions to establish safe operational limits of high burnup fuel. To conduct transient testing, a comprehensive understanding of steady-state fuel behavior obtained through both experimental characterization and accurate predictive capabilities is needed. This study comparatively assesses the steady-state irradiation performance of two high burnup U-19Pu-10Zr fuel pins, DP-36 and DP-40, irradiated under prototypic fast reactor conditions in preparation for planned safety testing at the Transient Reactor Test Facility. Since DP-40 was designated for use in the test and DP-36 serves as its sibling pin, non-destructive, engineering-scale post-irradiation examinations (PIE) were conducted on both pins while destructive examinations were performed exclusively on DP-36. The results were then assessed against historical performance data from similar fuel pins irradiated in the Experimental Breeder Reactor-II. Additionally, the steady-state irradiation of each pin was modeled using the BISON fuel performance code to assess the accuracy of current modeling capabilities in predicting the baseline irradiation behavior. Non-destructive examinations included neutron radiography to measure fuel column elongation, gamma scanning to verify pin integrity and fission product migration, and profilometry to assess dimensional changes. Benchmarking against existing PIE data revealed consistent patterns in axial fuel column growth and cladding diametral strain, though both pins exhibited longer low-density “fluff” structures, which can have implications for core reactivity and source term calculations. Destructive examinations on DP-36 included fission gas release analysis and sectioning for optical microscopy, which showed more complex constituent redistribution patterns than the traditionally accepted 3-ring model. The axial evolution of fractional areas and porosities of each of the redistributed zones were quantified and presented. Modeling comparisons showed agreement in fractional fission gas release but consistently overestimated axial and radial swelling and disagreed with measured axial porosity patterns. These conservative overpredictions suggested that the pins would appear closer to failure or operational limits at the start of transient tests, potentially leading to higher strain accumulation during the transient. While conservative estimates provide safety margins, they can negatively impact fuel economics. A review of the swelling models identified areas for improvement in the gaseous swelling, solid swelling, and fuel hot-pressing models when applied to ternary fuel. The results of this study highlight the critical importance of conducting pre-test characterization on both test and sibling pins to accurately capture steady-state fuel behavior, providing a precise baseline for post-test evaluations and essential inputs for transient modeling of the planned experiments. The analysis also revealed significant data gaps that require further investigation to enhance the understanding and prediction of fuel swelling and pore dynamics. Collecting comprehensive data across different irradiation conditions, burnup levels, and fuel compositions are essential for refining existing models and developing mechanistic models for both binary and ternary metallic fuels, ultimately improving the integration of modeling and experimental approaches in accident testing.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Engineered Solutions Group's SMR Containment Cable and Electrical Penetration Assembly System

GAIN Project CRADA Number NFE-21-08839, entitled “SMR Containment Cable and EPA System” was initiated by the partnership of Oak Ridge National Laboratory (ORNL) and Engineered Solutions Group (ESG) to test an ESG-designed Electrical Penetration Assembly and Containment Cabling System Qualified for not only legacy LWR designs, but also Small Modular Reactors designs currently being designed by several different suppliers. This project was undertaken to fill the equipment gap of EPA and Cabling Systems that require much more severe environmental requirements than legacy plant applications present due to their smaller containment volumes that result in high energy densities compared to legacy designs. This high energy density results in severe accident environments and more severe normal operating conditions as well. We developed two approaches to qualify Electrical Penetration Assembly (EPA) and Containment Cabling Systems for SMRs and Advanced Reactors. We take into consideration the more severe environmental parameters found with SMR designs. The system will need to meet a qualification test program addressing wear/cyclic aging, potential radiation exposure, thermal aging, vibration aging, thermal cycling, seismic qualification, electrical fault testing (per IEEE 317) and accident simulation. The equipment must meet the requirements of 10CFR50.49, GDC 50 in 10CFR50 Appendix A, and 10CFR50 Appendix J. NRC Regulatory Guides (RGs) identify an acceptable way of meeting regulatory requirements. RGs frequently endorse a standard for meeting these requirements. Specific to this review, equipment would be qualified in accordance with the following IEEE Standards. • IEEE 317-2013 (Electrical Penetration Assemblies), which is endorsed by RG 1.63, Rev. 3, • IEEE 323-2003 and the more current IEC/IEEE 60780-323 (Environmental Qualification of 1E Equipment) which is endorsed by RG 1.89. IEEE 323-2003 is endorsed by RG 1.209, • IEEE 344-2020 (Seismic Qualification. The 2013 version endorsed by RG 1.100, Rev. 4, with exceptions), • IEEE 383-2015 (Electrical Cables) (which is endorsed by RG 1.189 Rev. 4 and the -2003 version endorsed by RG 1.211 rev. 0), • IEEE 572-2019 (Electrical Connectors and Assemblies), which is endorsed by 1.156 Rev 1, and • [IEEE 1202 (endorsed by RG 1.189) would normally be applicable but the advanced cable designs are impervious to this cable flame test.] The primary goal of such a program is to provide an EPA design that can meet the qualification requirements for all legacy light water reactor plants currently operating as well as new plant designs including light water Small Modular Reactors. Thus, these requirements are applicable to plants licensed under 10CFR50 and 10CFR52. Other reactor designs may be evaluated, and this test system and qualification method applied to those applications if the requirements would satisfy the requirements of the intended plant. A secondary benefit of this work is to document some of the history and background in these requirements as there have been recent delays in an SMR licensing process due to NRC Requests for Additional Information in this subject matter area.

42 ENGINEERING↗

Development of Surveillance Test Articles for Materials Degradation Management in MSR Environment

Information on materials degradations during advanced reactor operations is limited Effects of materials degradations during reactor operations are synergistic, involving: Irradiation, corrosion, elevated temperature exposure and stress (creep-fatigue loading) Establishment of surrogate materials surveillance program for the management of materials degradations would be an important pathway in support of the timely licensing of advanced reactors

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Water NSTF Design, Instrumentation, and Test Planning

The following report serves as a formal introduction to the water-based Natural convection Shutdown heat removal Test Facility (NSTF) program at Argonne. Since 2005, this US Department of Energy (DOE) sponsored program has conducted large scale experimental testing to generate high-quality and traceable validation data for guiding design decisions of the Reactor Cavity Cooling System (RCCS) concept for advanced reactor designs. The most recent facility iteration, and focus of this report, is the operation of a 1/2 scale model of a water-RCCS concept. Several features of the NSTF prototype align with the conceptual design that has been publicly released for the AREVA 625 MWt SC-HTGR. The design of the NSTF also retains all aspects common to a fundamental boiling water thermosiphon, and thus is well poised to provide necessary experimental data to advance basic understanding of natural circulation phenomena and contribute to computer code validation. Overall, the NSTF program operates to support the DOE vision of aiding US vendors in design choices of future reactor concepts, advancing the maturity of codes for licensing, and ultimately developing safe and reliable reactor technologies. In this report, the top-level program objectives, testing requirements, and unique considerations for the water cooled test assembly are discussed, and presented in sufficient depth to support defining the program’s overall scope and purpose. A discussion of the proposed 6-year testing program is then introduced, which outlines the specific strategy and testing plan for facility operations. The proposed testing plan has been developed to meet the toplevel objective of conducting high-quality test operations that span across a broad range of single- and two-phase operating conditions. Details of characterization, baseline test cases, accident scenario, and parametric variations are provided, including discussions of later-stage test cases that examine the influence of geometric variations and off-normal configurations. The facility design follows, including as-built dimensions and specifications of the various mechanical and liquid systems, design choices for the test section, water storage tank, and network piping. Specifications of the instrumentation suite are then presented, along with specific information on performance windows, measurement uncertainties, and installation locations. Finally, descriptions of the control systems and heat removal networks are provided, which have been engineered to support precise quantification of energy balances and facilitate well-controlled test operations.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Conceptual Design of Neutron Sensor Qualification Device

The Advanced Sensors and Instrumentation Program at Idaho National Laboratory has been formulating strategies to qualify sensors for use in nuclear environments, particularly in irradiation experiments and advanced reactors. When qualifying neutron sensors for use in high-temperature environments, the wide range of neutron flux levels and representative energy spectra presents significant challenges. This paper discusses the development of the Neutron Sensor Qualification Device (NQD), which is designed to test neutron sensors in high temperature controlled environments with known neutron spectra, addressing the spatial and spectral complexities of neutron fluxes in reactor cores. The proposed NQD will be situated in the exposure room at the Armed Forces Radiobiology Research Institute, thus affording a unique capability to expose sensors to high neutron and gamma fluxes. To achieve thermal control, the device will utilize a radiation-hardened tube furnace, accommodating multiple sensors and neutron activation dosimetry wires. Titanium, iron, and cobalt dosimeter wires are chosen from the American Society for Testing and Materials and International Reactor Dosimetry and Fusion File libraries as references for providing energy-dependent fluence measurements. The design ensures precise sensor positioning to minimize mutual shielding and flux perturbation, which are evaluated via Monte Carlo N particle Transport Code (MCNP) simulations. These simulations have informed the development of guidelines on sensor placement within the NQD. The NQD is essential to the qualification of neutron sensors for advanced reactor technologies. It enables controlled testing of a statistically significant number of sensors, thereby supporting assessments of sensor performance across various neutron flux levels and temperatures. This paper highlights the detailed planning for the NQD prototype, along with its inaugural irradiation (scheduled for fiscal year [FY] 2025). The results from this initial testing will be fundamental in evaluating the device’s performance and establishing measurement uncertainty for in-pile neutron sensor measurements.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

GAIN Technology Workshops Summary Report

National and global demand for nuclear energy is increasing and United States (U.S.) global leadership is eroding. There is a sense of urgency with respect to the deployment of the innovative nuclear energy technologies. The Gateway for Accelerated Innovation in Nuclear (GAIN) initiative is based on the simultaneous achievement of three strategic goals. The first is maintaining global technology leadership within the U.S. Department of Energy (DOE). The second is enabling global industrial leadership for nuclear vendors and suppliers. The third is focused on utility optimization of nuclear energy within the clean energy portfolio. An effective public-private partnership is required to achieve these goals. DOEs recognizes the recent sense of urgency new developers and investors have in getting their concepts to market. They know that time to market for nuclear technology takes too long and the facilities needed to conduct the necessary research, development and demonstration (RD&D) activities are very expensive to develop and maintain. Early technologies, in the lower technology readiness levels (TRL) need materials testing, analysis, modeling, code development, etc., most of which currently exists in the DOE national laboratory system. However, mature technologies typically need large component testing and demonstration facilities, which are expensive and long-lead efforts. By understanding the needs of advanced nuclear technology developers, GAIN will connect DOE national laboratory capabilities (e.g., facilities, expertise, materials, and data) with industry RD&D needs. In addition, GAIN is working with the Nuclear Regulatory Commission (NRC) to streamline processes and increase understanding of the licensing requirements for advanced reactors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Release on the Virtual Test Bed of a Molten Salt Reactor Experiment SAM-Pronghorn Coupled Model using the Domain Overlapping Approach

The nuclear industry is taking leaps in innovations with companies seeking a sustainable energy future through advanced nuclear reactors. The Department of Energy (DOE)’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program seeks to substantiate and bolster the deployment of advanced reactors through flexible multifidelity, multiphysics simulations of advanced nuclear reactors. Applications like SAM for one-dimensional systems thermalhydraulics, and Pronghorn for multidimensional coarse mesh thermal-hydraulics, are geared to support innovations in industry by facilitating design, optimization, and licensing of advanced nuclear reactors. Coupling systems thermal-hydraulics and computational fluid dynamics codes can be difficult as the pressure coupling converges slowly; however, it is important to obtain the desired accuracy in each part of the primary loop. The authors of this model created an Overlapping-Domain Coupling (ODC) approach to coupling SAM and Pronghorn. Leveraging this coupling technique, a Molten Salt Reactor Experiment (MSRE) model was developed and released to the NEAMS/National Reactor Innovation Center (NRIC) Virtual Test Bed (VTB). The MSRE was chosen to be modeled because of the wealth of experimental data available and because of the strong physics coupling between the core and primary circuit. This paper contextualizes the history of the MSRE, describes the thermal hydraulics models used, and detail the implementation of multidimensional thermal-hydraulics and system codes based on the ODC method for the MSRE model. Finally, this paper presents how other modelers could apply the SAM Pronghorn ODC for other advanced reactor models.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Fuel Safety Research Plan for Accident Tolerant Fuels

This document outlines a strategic plan for a safety research program for accident tolerant fuels. Accident tolerant fuels (ATFs) are nuclear fuel materials and designs for existing and future light water reactors. This effort is under the Department of Energy Office of Nuclear Energy’s Nuclear Technology Research and Development Advanced Fuels Campaign. The development of ATF is an industry lead initiative with fuel designs being championed by Westinghouse, Framatome, and General Electric. Industry goals for ATF deployment include implementing the first batch reloads of coated cladding and doped fuel designs into commercial reactors by 2023 and having the first batch reloads of more advanced designs into commercial reactors by 2026. Follow on goals include implementing the first full cores of coated cladding and doped fuel designs into commercial reactors by 2026 and implementing full cores of more advanced designs by 2030. The objectives of the national laboratory research programs within the Advanced Fuels Campaign related to ATF are: 1. Develop and maintain of unique nuclear testing infrastructure, which includes test reactors, hot cell PIE equipment, and unique out of pile separate effects testing facilities. 2. Respond directly to industry requests for support by partnering with the ATF vendors and executing experiments and/or analysis on their behalf. 3. Conduct independent scientific investigations into the performance of the different ATF concepts that are relevant to Industry designs. To achieve these objectives, the safety research program will execute transient irradiation experiments at the TREAT facility at Idaho National Laboratory with the aim of identifying the relevant transient fuel behaviors for each fuel design in order to establish appropriate fuel safety criteria and thresholds. Two test series are described in this plan, (1) an Integral Test Series, and (2) a Focused Effects Test Series. In fulfillment of the first objective for the safety research program, Integral Effects Tests will be developed and demonstrated using standard UO2 Zircaloy fuel designs in both the fresh and previously irradiated case. The Integral Test Series will consist of three campaigns to evaluate transient fuel performance in Reactivity Initiated Accidents, Loss of Coolant Accidents, and in generalized Power Cooling Mismatch scenarios. Development of these test programs also enables the safety research program to fulfill its second objective by making these three test programs available to each industry team. Initially, priority will be given in the integral test series to the coated cladding and doped fuel concepts as their deployment schedule is the most aggressive. To fulfill the third objective of the safety research program, a Focused Effects Test Series is also being developed which will examine specific transient fuel behaviors that are of general interest to all the ATF designs under development. These tests look at transient fuel behavior related to pellet cladding mechanical interaction, coated cladding swelling, rupture, and time at temperature behavior, non oxide fuel melting and mechanical interaction with Silicon Carbide cladding, UO2 and doped UO2 fuel fragmentation and transient fission gas release, and finally fuel coolant interaction. This document provides a general overview of the objectives of the safety research program as well as providing background into how programs like this have been used in the past to develop the criteria necessary for the safe operation of the present fuel designs. An overview of the materials and methods used for safety testing is presented. Finally the Integral and Focused Effects tests series are introduced and described. This document will be maintained as a “living” document with annual updates to reflect evolving requirements and needs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

HYTEST Phase I Facility Commissioning and Modeling

The purpose of this document is to report the first year accomplishments of two coordinated Laboratory Directed Research and Development (LDRD) projects that utilize a hybrid energy testing laboratory that couples various reactors to investigate system reactance behavior. This work is the first phase of a series of hybrid energy research and testing stations - referred to hereafter as HYTEST facilities – that are planned for construction and operation at the Idaho National Laboratory (INL). A HYTEST Phase I facility was set up and commissioned in Bay 9 of the Bonneville County Technology Center (BCTC). The purpose of this facility is to utilize the hydrogen and oxygen that is produced by the High Temperature Steam Electrolysis test reactors operating in Bay 9 to support the investigation of kinetic phenomena and transient response of integrated reactor components. This facility provides a convenient scale for conducting scoping tests of new reaction concepts, materials performance, new instruments, and real-time data collection and manipulation for advance process controls. An enclosed reactor module was assembled and connected to a new ventilation system equipped with a variable-speed exhaust blower to mitigate hazardous gas exposures, as well as contract with hot surfaces. The module was equipped with a hydrogen gas pump and receiver tank to supply high quality hydrogen to chemical reactors located in the hood.

08 HYDROGEN↗

Intermediate-Term Thermal Aging Effect Evaluation for Grade 92 and 316L at The LWR Relevant Temperature

Life extension of the existing nuclear reactors imposes accumulated damages, such as higher fluences and longer period of corrosion, to structural materials, which would result in significant challenges to the traditional reactor materials such as type 304 and 316 stainless steels. Advanced alloys with superior radiation resistance will increase safety margins, design flexibility, and economics for not only the life extension of the existing fleet but also new builds with advanced reactor designs. The Electric Power Research Institute (EPRI) teamed up with Department of Energy (DOE) on the Advanced Radiation Resistant Materials (ARRM) program, aiming to develop and test degradation resistant alloys from current commercial alloy specifications by 2021 to a new advanced alloy with superior degradation resistance in light water reactor (LWR)-relevant environments by 2024. Based on a comprehensive microstructure and property screening performed in Phase-1 of the ARRM program, a total of five alloys, together with 316L and X-750 as references, were down-selected for Phase-2 neutron irradiation studies. Because thermal aging could exert a synergistic effect on neutron irradiation due to the low neutron damage rate on the order of 10 –7 displacements per atom per second (dpa/s), Grade 92 (one of the five down-selected alloys) and two heats of 316L were selected in this task to study the effect of aging at 350°C for 12.5–12.7 kh on microstructure and mechanical properties. The aging time is approximately corresponding to 5 dpa neutron irradiation, which can be served as a reference for the 5-dpa-irradiated samples of the alloys to help understand the independent neutron damage influence on microstructure and mechanical properties. Optical microscopy and scanning electron microscopy were used for microstructural characterization. Hardness, tensile, Charpy impact toughness, and fracture toughness in the ductile regime of the aged samples were examined. The aging of Grade 92 led to the formation of many Laves phase in sizes of ~100–200 nm and resulted in some reduction in hardness and yield/ultimate tensile strength with some increases in uniform and total plastic elongations, which may have helped the enhancement of Charpy impact toughness, e.g., ~4 J increase in upper-shelf energy and 20.5°C reduction in ductile-brittle transition temperature compared with the unaged condition. The fracture toughness of the aged Grade 92 showed decent toughness of ~303 MPa√m (K Jq ) with ~87 tearing modulus at 22°C, which reduced to ~241 MPa√m (~20% reduction) with ~75 tearing modulus at 300°C. The two heats of 316L are differentiated by their amounts of δ-ferrite, i.e., ~1 vol% in heat T1103 and ~4 vol% in heat N5B8. The two heats of 316L were subjected to 15% cold work (CW) as this condition is often used in nuclear reactors to help trapping radiation-induced defects and thus postpone the steady state swelling stage. The aging did not result in any noticeable microstructure changes, except for possible segregations at grain boundaries that need to be further investigated. The aging resulted in slight reduction in hardness of 316L-T1103 and slight increase in hardness of 316L-N5B8, which is consistent with their tensile testing results. The 15%CW might have introduced some inhomogeneity, resulting in large standard deviations in hardness, which were reduced after the aging. The aged 316L followed the same trend as the unaged condition for the strength and elongation results from the tensile testing. Minimum elongations appeared within ~300–600°C, above which the elongations seem to increase. Unlike the negligible or minor changes in microstructure, hardness and tensile results of the two heats of 316L, their fracture toughness showed noticeable difference. The aged 316L-T1103 showed good toughness of ~350 MPa√m with ~80 tearing modulus at 22°C, which reduced to ~271 MPa√m (~23% reduction) with ~83 tearing modulus at 300°C. In contrast, the aged 316L-N5B8 showed lower toughness of ~244 MPa√m with ~53 tearing modulus at 22°C, which reduced to ~180 MPa√m (~26% reduction) with ~31 tearing modulus at 300°C. The preliminary results indicate that the presence of high volume of δ-ferrite would noticeable impair fracture toughness although it may not influence hardness and tensile properties.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗