Search NASA⌕ Search

SEARCH · Search NASA

Results for “Analytical Method Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

System Identification of Damped Truss-Like Space Structures

A spacecraft payload flown on a launch vehicle experiences dynamic loads. The dynamic loads are caused by various phenomena ranging from the start-up of the launch vehicle engine to wind gusts. A spacecraft payload should be designed to meet launch vehicle dynamic loads. One of the major steps taken towards determining the dynamic loads is to correlate the finite element model of the spacecraft with the test results of a modal survey test. A test-verified finite element model of the spacecraft should possess the same spatial properties (stiffness, mass, and damping) and modal properties (frequencies and mode shapes) as the test hardware representing the spacecraft. The test-verified and correlated finite element model of the spacecraft is then coupled with the finite element model of the launch vehicle for analysis of loads and stress. Modal survey testing, verification of a finite element model, and modification of the finite element model to match the modal survey test results can easily be accomplished if the spacecraft structure is simple. However, this is rarely the case. A simple structure here is defined as a structure where the influence of nonlinearity between force and displacement (uncertainty in a test, for example, with errors in input and output), and the influence of damping (structural, coulomb, and viscous) are not pronounced. The objective of this study is to develop system identification and correlation methods with the focus on the structural systems that possess nonproportional damping. Two approaches to correct the nonproportional damping matrix of a truss structure were studied, and have been implemented on truss-like structures such as the National Aeronautics and Space Administration's space station truss. The results of this study showed nearly 100 percent improvement of the correlated eigensystem over the analytical eigensystem. The first method showed excellent results with up to three modes used in the system identification process. The second method could handle more modes, but required more computer usage time, and the results were less accurate than those of the first method.

Armand, Sasan↗

Formulation of an improved smeared stiffener theory for buckling analysis of grid-stiffened composite panels

A smeared stiffener theory for stiffened panels is presented that includes skin-stiffener interaction effects. The neutral surface profile of the skin-stiffener combination is developed analytically using the minimum potential energy principle and statics conditions. The skin-stiffener interaction is accounted for by computing the stiffness due to the stiffener and the skin in the skin-stiffener region about the neutral axis at the stiffener. Buckling load results for axially stiffened, orthogrid, and general grid-stiffened panels are obtained using the smeared stiffness combined with a Rayleigh-Ritz method and are compared with results from detailed finite element analyses.

Jaunky, Navin↗

Face Gear Drive with Spur Involute Pinion: Geometry, Generation by a Worm, Stress Analysis

A face gear drive with a spur involute pinion is considered. The generation of the face gear is based on application of a grinding or cutting worm whereas the conventional method of generation is based on application of an involute shaper. An analytical approach is proposed for the determination of: (1) the worm thread surface; (2) avoidance of singularities of the worm thread surface, (air) dressing of the worm; and (3) determination of stresses of the face-gear drive. A computer program for simulation of meshing and contact of the pinion and face-gear has been developed. Correction of machine-tool settings is proposed for reduction of the shift of the bearing contact caused by misalignment. An automatic development of the model of five contacting teeth has been proposed for stress analysis. Numerical examples for illustration of the developed theory are provided.

Litvin, Faydor L.↗

Integration of an Autopilot for a Micro Air Vehicle

Two autopilots providing autonomous flight capabilities are presented herein. The first is the Pico-Pilot, demonstrated for the 12-inch size class of micro air vehicles. The second is the MicroPilot MP2028(sup g), where its integration into a 36-inch Zagi airframe (tailless, elevons only configuration) is investigated and is the main focus of the report. Analytical methods, which include the use of the Advanced Aircraft Analysis software from DARCorp, were used to determine the stability and control derivatives, which were then validated through wind tunnel experiments. From the aerodynamic data, the linear, perturbed equations of motion from steady-state flight conditions may be cast in terms of these derivatives. Using these linear equations, transfer functions for the control and navigation systems were developed and feedback control laws based on Proportional, Integral, and Derivative (PID) control design were developed to control the aircraft. The PID gains may then be programmed into the autopilot software and uploaded to the microprocessor of the autopilot. The Pico-Pilot system was flight tested and shown to be successful in navigating a 12-inch MAV through a course defined by a number of waypoints with a high degree of accuracy, and in 20 mph winds. The system, though, showed problems with control authority in the roll and pitch motion of the aircraft: causing oscillations in these directions, but the aircraft maintained its heading while following the prescribed course. Flight tests were performed in remote control mode to evaluate handling, adjust trim, and test data logging for the Zagi with integrated MP2028(sup g). Ground testing was performed to test GPS acquisition, data logging, and control response in autonomous mode. Technical difficulties and integration limitations with the autopilot prevented fully autonomous flight from taking place, but the integration methodologies developed for this autopilot are, in general, applicable for unmanned air vehicles within the 36-inch size class or larger that use a PID control based autopilot.

Platanitis, George↗

Nanomaterials Work at NASA-Johnson Space Center

Nanomaterials activities at NASA-Johnson Space Center focus on single wall carbon nanotube production, characterization and their applications for aerospace. Nanotubes are produced by arc and laser methods and the growth process is monitored by in-situ diagnostics using time resolved passive emission and laser induced fluorescence of the active species. Parametric study of both these processes are conducted to monitor the effect of production parameters including temperature, buffer gas, flow rate, pressure, laser fluence and arc current. Characterization of the nanotube material is performed using the NASA-JSC protocol developed by combining analytical techniques of SEM, TEM, UV-VIS-NIR absorption, Raman, and TGA. Efforts at JSC over the past five years in composites have centered on structural polymernanotube systems. Recent activities broadened this focus to multifunctional materials, supercapacitors, fuel cells, regenerable CO2 absorbers, electromagnetic shielding, radiation dosimetry and thermal management systems of interest for human space flight. Preliminary tests indicate improvement of performance in most of these applications because of the large surface area as well as high conductivity exhibited by SWCNTs.

Arepalli, Sivaram↗

Advanced Analytics and Big Earth Data

NASA's Earth Science Data Systems process, archive and distribute petabytes of Earth Observation data to a variety of end users. These end users will face dramatically increased data size in the near future, bringing about new challenges and opportunities in analyzing those data. One area of particular ferment currently is Machine Learning. Many Machine Learning methods are black boxes, limiting direct insight into the data's properties. However, they can be used for a variety of data enhancement purposes, such as parameter retrieval, data fusion and image classification and segmentation. The Earth Observing System Data and Information System is also evolving to host large data volumes in the cloud, enabling data proximal analysis. As part of this effort, an Analytics framework is being developed to support and enhance user analysis of the data. By using standards based services in the framework, diverse user communities can be served, while also allowing inter-system collaboration in the analysis process.

Cloud Computing↗

Development of Acoustic Mufflers for Cabin Noise Reduction in Orion Spacecraft

Controlling cabin acoustic noise levels in the Crew Module (CM) of the Orion spacecraft is critical to ensure adequate speech intelligibility, to avoid fatigue, and prevent any possibility of temporary and permanent hearing loss to the crew. The primary source of cabin noise for the on-orbit phase of the mission is from the Environmental Control and Life Support System (ECLSS) which recycles and conditions breathing air and maintains cabin pressurization through its duct network and components. Unfortunately, as a side effect, noise from the ECLSS fans propagates through theses ducts and emanate into the cabin habitable volume via the ECLSS inlet and outlets. To mitigate excessive duct-borne noise, two ECLSS mufflers have been designed to provide significant acoustic transmission loss (TL) so that the cabin noise requirements can be met. Each muffler is meant to be installed in the ducting of the ECLSS air inlet and outlet sides, respectively. Packaging constraints and tight volume requirements necessitated the mufflers to be of complex geometry and compatible with the bends of the ECLSS duct layout. To design and characterize the acoustic performance of the inlet and outlet mufflers, computational acoustic models were developed using the Finite Element Method (FEM) with 𝑤𝑎𝑣𝑒଺ vibroacoustic software. Characterization of the acoustic material and perforations in the mufflers were addressed with poroelastic theory. Once the mufflers were designed on paper and its TL predicted, prototypes of these mufflers were created using additive manufacturing. The muffler prototypes were subsequently tested for acoustic TL in the laboratory with various con-figurations of acoustic materials. Comparing the analytical predictions to the test performance yielded excellent correlation for acoustic TL and demonstrated significant broadband noise attenuation. The ECLSS mufflers are currently scheduled to be installed on the Artemis II Crew Module (CM) of the Orion spacecraft and will provide significant cabin comfort to crew during the mission.

Indranil Dandaroy↗

Investigation to develop a multistage forest sampling inventory system using ERTS-1 imagery

The author has identified the following significant results. The annotation system produced a RMSE of about 200 m ground distance in the MSS data system with the control data used. All the analytical MSS interpretation models tried were highly significant. However, the gains in forest sampling efficiency that can be achieved by using the models vary from zero to over 50 percent depending on the area to which they are applied and the sampling method used. Among the sampling methods tried, regression sampling yielded substantial and the most consistent gains. The single most significant variable in the interpretation model was the difference between bands 5 and 7. The contrast variable, computed by the Hadamard transform was significant but did not contribute much to the interpretation model. Forest areas containing very large timber volumes because of large tree sizes were not separable from areas of similar crown cover but containing smaller trees using ERTS image interpretation only. All correlations between space derived timber volume predictions and estimates obtained from aerial and ground sampling were relatively low but significant and stable. There was a much stronger relationship between variables derived from MSS and U2 data than between U2 and ground data.

Langley, P. G.↗

Assumed modes method and flexible multibody dynamics

The use of assumed modes in flexible multibody dynamics algorithms requires the evaluation of several domain dependent integrals that are affected by the type of modes used. The implications of these integrals - often called zeroth, first and second order terms - are investigated in this paper, for arbitrarily shaped bodies. Guidelines are developed for the use of appropriate boundary conditions while generating the component modal models. The issue of whether and which higher order terms must be retained is also addressed. Analytical results, and numerical results using the Shuttle Remote Manipulator System as the multibody system, are presented to qualitatively and quantitatively address these issues.

Tadikonda, S. S. K.↗

Performance and Dynamics of Aerospace Vehicles

This publication consists of a series of lectures prepared by personnel of the NASA Langley Research Center. Collectively, they were presented as a graduate seminar at Rensselaer Polytechnic Institute, Troy, New York, under the auspices of Professor Robert E. Duffy. The lectures summarize theoretical and experimental work in a number of areas of current interest in the design of aeronautical and space vehicles and were intended as an extension of general academic studies toward applications to solutions of practical problems. The material presented is not intended to be a comprehensive survey of the state of the art but rather a series of resumes of work in several areas, some of which represent fairly recent developments and others in which the significant contributions are distributed in various publications. The material covered reflects the specialties and viewpoints of the individual lecturers and little effort has been made to provide continuity between the different papers. The topics are, nevertheless, grouped under three general headings, as follows: 1. Aerodynamics of vehicles in various speed ranges 2. Problems involving aeroelasticity and unsteady aerodynamics 3. Methods and application of analytical techniques in dynamic stability problems The material is considered suitable for providing aeronautical engineering students with background information and working knowledge in a number of specialized fields which are usually omitted or discussed only briefly in an undergraduate curriculum.

Source record↗

Analytical and experimental study of supersonic combustion of hydrogen in a vitiated airstream

Detailed probe measurements of total temperature, pressure, and composition were taken in a two-dimensional test section 35.6 cm downstream of hydrogen injection. A high pressure gas generator supplied Mach 2.44 vitiated air or inert gas at elevated temperatures and at a static pressure equal to that of the hydrogen. Special water-cooled probes and sampling techniques were developed for the short test times required by heat-sink hardware. Independent methods of measuring stream total temperatures are compared. For the pure mixing case, the computed composition profile agreed well with the experimental profile. The analysis takes into account the wall boundary layer and the initial boundary layer in the main stream. Ignition of hydrogen, as determined from photographic exposures of the radiating gases, varied from 30 to 10 cm downstream from injection for a 45 K increase in local free-stream static temperature.

Burrows, M. C.↗

Propagation of plane waves in flow through a variable area duct

Duct geometry is an important factor that influences the transmission of sound in a duct. Nonconstant area produces variations in steady flow quantities through the duct, which can cause reflections of acoustic disturbances and the creation of standing wave patterns, and which can attenuate and disperse propagating waves. To study the problem, a second-order-accurate numerical method has been developed. The method of characteristics is used to solve the acoustic equations with the assumption of quasi-one-dimensional flow in the duct. Numerical results are presented over a broad range of frequencies. Low-frequency results are compared with approximate solutions for compact nozzles and high-frequency calculations are compared with results from the short-wave theory. The numerical results are also compared with an analytical solution of the acoustic equations for exponential horn sections with zero mean flow to further establish the validity of the numerical method.

King, L. S.↗

Prediction of in-depth oxidation distribution of reinforced carbon-carbon materials for Space Shuttle leading edges

A method was developed for predicting oxidation distribution through the thickness of reinforced carbon-carbon material in an earth atmospheric entry environment. A mathematical model was developed which describes oxygen diffusion and reaction rates within material pores. Pertinent rate constants were derived, and material mass loss was computed for a range of temperatures and pressures. Results indicate that both temperature and pressure have an important effect on mass loss distribution. Analytical results were quite consistent with results of ground oxidation tests.

Medford, J. E.↗

Development of a drift-correction procedure for a photoelectric spectrometer

A technique has been developed to automatically correct for drifts in the radiometric sensitivity of the detector channels in a direct-reading emission spectrometer. The method utilizes a 1000 W tungsten-halogen reference lamp to illuminate the detectors through the same optical path as that traversed during the analysis of the sample. Detector channel responses to the light are compared to those for the same light intensity at the time of analytical calibration. This corrects for the drift. It is noted that with the exception of positioning the lamp, the procedure is fully automatic.

Chapman, G. B., II↗

The response of turbine engine rotors to interference rubs

A method was developed for the direct integration of a rotor dynamics system experiencing a blade loss induced rotor rub. Both blade loss and rotor rub were simulated on a rotor typical of a small gas turbine. A small change in the coefficient of friction (from 0.1 to 0.2) caused the rotor to change from forward to backward whirl and to theoretically destroy itself in a few rotations. This method provides an analytical capability to study the susceptibility of rotors to rub induced backward whirl problems.

Kascak, A. F.↗

HPOTP low-speed flexible rotor balancing, phase 1

A method was developed that shows promise in overcoming many balancing limitations. This method establishes one or more windows for low speed, out-of-housing balancing of flexible rotors. These windows are regions of speed and support flexibility where two conditions are simultaneously fulfilled. First, the rotor system behaves flexibly; therefore, there is separation among balance planes. Second, the response due to balance weights is large enough to reliably measure. The analytic formulation of the low-speed flexible rotor balancing method is described. The results of proof-of-principle tests conducted under the program are presented. Based on this effort, it is concluded that low speed flexible rotor balancing is a viable technology. In particular, the method can be used to balance a rotor bearing system at low speed which results in smooth operation above more than one bending critical speed. Furthermore, this balancing methodology is applicable to SSME turbopump rotors.

Giordano, J.↗

The kinematics and dynamics of space manipulators - The virtual manipulator approach

Future robotic manipulator systems will be required to perform complex tasks in space such as satellite repair. These robotic manipulators will encounter a number of kinematic, dynamic, and control problems caused by the dynamic coupling between the manipulators and its spacecraft. This dynamic coupling also makes it difficult to analyze these systems. This paper introduces a new analytical modeling method for space manipulators called the Virtual Manipulator (VM), which has a fixed based in inertial space at a point called a Virtual Ground. The kinematics and dynamics of the manipulator, spacecraft, and payload can be described relatively easily in terms of the VM. With its fixed base, the Virtual Manipulator is shown to have the potential to be an effective aid for the analysis, design, and development of future space manipulator systems.

Vafa, Z.↗

Unsteady three-dimensional thermal field prediction in turbine blades using nonlinear BEM

A time-and-space accurate and computationally efficient fully three dimensional unsteady temperature field analysis computer code has been developed for truly arbitrary configurations. It uses boundary element method (BEM) formulation based on an unsteady Green's function approach, multi-point Gaussian quadrature spatial integration on each panel, and a highly clustered time-step integration. The code accepts either temperatures or heat fluxes as boundary conditions that can vary in time on a point-by-point basis. Comparisons of the BEM numerical results and known analytical unsteady results for simple shapes demonstrate very high accuracy and reliability of the algorithm. An example of computed three dimensional temperature and heat flux fields in a realistically shaped internally cooled turbine blade is also discussed.

Martin, Thomas J.↗