Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compressive Strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Characterization of IM7/8552 Thin-Ply and Hybrid Thin-Ply Composites

Composite materials have increasingly been used for aerospace applications due to improved performance and reduced weight compared to their metallic counterparts. Inclusion of thin-ply material, plies with cured thickness half or less than standard composites, have potential to improve performance and reduce structural weight. Limited characterization of thin-ply IM7/8552 material in 30 and 70 grams per square meter fiber areal weights has been carried out using a series of selected American Society for Testing and Materials (ASTM) tests. Tests included unnotched tension, unnotched compression, v-notched rail shear, open-hole tension, and open-hole compression. Unidirectional, cross-ply, quasiisotropic and hybrid hard laminates were included in the study, and were compared to standard-ply laminates. Properties compared include fiber volume, laminate moduli, and failure strength, with failure modes also being examined. The thin-ply specimens exhibited similar or superior performance to standard ply laminates in many of the cases compared. Improvements in strength for laminates containing thin-ply material were seen for unidirectional laminates under unnotched tension, quasi-isotropic laminates under unnotched tension and compression, and hard laminates under open hole tension. Additional investigation is required to determine appropriate ply stacking rules for hybrids of thin and standard plies to avoid undesirable failure modes such as axial splitting. However, the observed performance improvements demonstrated by the conducted ASTM tests of hybrid thin-ply hard laminates could have benefits for improved structural weight in aircraft.

Lovejoy, Andrew E.↗
DOE OSTI2022

Extraordinary Strain Hardening from Dislocation Loops in Defect-Free Al Nanocubes

The complex interaction of crystalline defects leads to strain hardening in bulk metals. Metals with high stacking fault energy (SFE), such as aluminum, tend to have low strain hardening rates due to an inability to form stacking faults and deformation twins. Here, we use in situ SEM mechanical compressions to find that colloidally synthesized defect-free 114 nm Al nanocubes combine a high linear strain hardening rate of 4.1 GPa with a high strength of 1.1 GPa. These nanocubes have a 3 nm self-passivating oxide layer that has a large influence on mechanical behavior and the accumulation of dislocation structures. Post-compression TEM imaging reveals stable prismatic dislocation loops and the absence of stacking faults. MD simulations relate the formation of dislocation loops and strain hardening to the surface oxide. These results indicate that slight modifications to surface and interfacial properties can induce enormous changes to mechanical properties in high SFE metals.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Elucidating the mechanical and thermal response of nanotwinned Ni alloys

Transformative advances in nanoscale materials synthesis, characterization and modeling are enabling the synthesis of materials with unprecedent properties and greater understanding of the nanoscale mechanisms that underpin these properties. Nanotwinned Cu alloys have received considerable attention due to their impressive balance of strength and ductility, but they have limited microstructural stability. Recent instantiation of nanotwins in sputter deposited Ni-Mo-W, and several commercial Ni-based superalloys, point to the potential development of a new class of high temperature materials with a very beneficial suite of mechanical and physical properties. The experimental study described in this report was undertaken to elucidate the nanoscale origins of the thermal and mechanical behavior of nanotwinned Ni alloys. Micropillar compression experiments have shown nanotwinned Ni 85 Mo 15-x W x alloys to possess unusually high strengths above 3.5GPa and enhanced microstructural stability. The strength of these nanotwinned alloys is determined by the abrupt formation of shear bands. This study focused on identifying the nanoscale trigger, or triggers, for shear banding in nanotwinned materials using in situ experiments and atomic-scale postmortem analysis. Contrasting and comparing the mechanical response and postmortem nanostructures of “Mo-rich” and “W-rich” nanotwinned specimens elucidated the importance of the lateral motion of easy glide defects that results in erasure of twins and local coarsening of the nanotwinned microstructure. This twin coarsening was then associated with very localized plasticity, strain softening, and shear band formation. The difference between alloys was further studied by considering the role of various material factors: stacking fault energy, coherent twin boundary spacing and flatness, grain size, and the interactions of solute atoms with twin and grain boundaries. The effect of alloy composition and sputtering power and temperature were also investigated and used to control twin spacing and geometry. Combined with atomic-scale simulations, these experiments insights should allow us to identify strategies for achieving concomitant ultrahigh strength and ductility in nanotwinned Ni alloys. In parallel but synergistic studies, our work was buoyed by collaborative state-of-the-art nanoscale orientation and strain mapping at the DOE National Center for Electron Microscopy (NCEM). For example, novel 4D-STEM techniques were used to acquire nanoscale strain maps. The extremely fine twin spacing limited our measurements of atomic-scale thermal expansion within twins, but recent results from NCEM suggest that it will soon be possible to conduct such measurements and to unravel the origins of the novel thermal expansion characteristics of nanotwinned Ni alloys.

36 MATERIALS SCIENCE↗
NASA NTRS1981

Development of experimental concepts for investigating the strength behavior of fine-grained cohesive soil in the Spacelab/space shuttle zero-g environment

Three different sets of tests are proposed for the NASA Spacelab experimental program. The first of tests, designed to measure the true cohesion of several different soils, would be carried out in space through use of a specially prepared direct shear apparatus. As part of this first series of tests, it is recommended that a set of drained unconfined compression tests be performed terrestrially on the same soils as tested in space. A form of the direct tension test is planned to measure the true tensile strength of the same types of soils used in the first series of tests. The direct tension tests could be performed terrestrially. The combined results of the direct shear tests, direct tension tests, and unconfined compression tests can be used to construct approximate failure envelopes for the soils tested in the region of the stress origin. Relationships between true cohesion and true tensile strength can also be investigated. In addition, the role of physio-chemical variables should be studied. The third set of tests involves using a multiaxial cubical or true triaxial test apparatus to investigate the influence of gravity induced fabric anisotropy and stress nonhomogeneities on the stress strain behavior of cohesive soils at low effective stress levels. These tests would involve both in space and terrestrial laboratory testing.

Bonaparte, R.↗
DOE OSTI2022

Role of α → ε → α phase transformation on the spall behavior of iron at atomic scales

Shock compression of iron microstructures above a threshold stress results in a α (BCC) → ε (HCP) transformation and the propagation of the release wave brings the metal back to the α phase following the ε→α transformation. Predicting failure behavior under shock loading conditions (spallation) relies on understanding the evolution of defects in the microstructure as it undergoes the α→ε→α phase transformation. This study uses molecular dynamics (MD) simulations to investigate the role of defect evolution during α→ε→α phase transformation on the spall strength values of single-crystal (sc) Fe microstructures. The MD simulations aim to characterize the ε phase fraction formed during shock compression and the defects during shock release for variations in loading orientations and shock stresses. The simulations are carried out for loading along the [100], [110], [111], and [112] orientations and for impact velocities ranging from 600 m/s to 1 km/s. The ε phase fractions during compression and defects (dislocations, twins) characterized during spall failure show an orientation dependence that affects the spall strength values. Here, the lowest value for spall strength is observed for the <110> loading orientation that shows a high density of twinning at the spall plane, whereas the highest value is observed for the <100> orientation and is associated with a α (BCC) → γ (FCC) transformation at the spall plane. The correlations of the spall strength values with the strain rates and with the ε phase fractions are discussed.

36 MATERIALS SCIENCE↗
NASA NTRS1998

Damage Tolerance of Sandwich Plates with Debonded Face Sheets

Axial compression tests were performed on debonded sandwich composites made of graphite/epoxy face-sheets and aramid fiber honeycomb core. The sandwich beams were manufactured using a vacuum baccrin2 process. The face-sheet and the sandwich beam were co-cured. Delamination between one of the face sheets and the core was introduced by using a Teflon layer during the curing process. Axial compression tests were performed to determine the ultimate load carrying capacity of the debonded beams. Flatwise tension tests and Double Cantilever Beam tests were performed to determine. respectively, the strength and fracture toughness of the face-sheet/core interface. From the test results semi-empirical formulas were derived for the fracture toughness and ultimate compressive load carrying capacity in terms of the core density. core thickness. face-sheet thickness and debond length. Four different failure modes and their relation to the structural properties were identified. Linear buckling analysis was found to be inadequate in predicting the compressive load carrying capacity of the debonded sandwich composites.

Avery, John L., III↗
DOE OSTI2019

Effect of Vertical Strut Arrangements on Compression Characteristics of 3D Printed Polymer Lattice Structures: Experimental and Computational Study

This paper discusses the behavior of the three-dimensional (3D) printed polymer lattice core structures during compressive deformation, by both physical testing and computer modeling. Four lattice configurations based on the body-centered cubic (BCC) unit cell were selected to investigate the effect of vertical strut arrangements on stiffness, failure load, and energy absorption per unit mass or the specific energy absorption (SEA). The basic BCC unit cell consists of struts connecting the body center to the corners of the cube. Three variations in the BCC configuration considered in this study are (1) BCCV, with vertical members connecting all nodes of the lattice, (2) BCCA, with vertical members in alternating layers of the lattice, and (3) BCCG, with a gradient in the number of vertical members increasing from none at the top layer to all vertical members at the bottom layer. The unit cell dimensions were 5 mm × 5 mm × 5 mm with strut diameter of 1 mm. The lattice was assembled with 5 cells in the x and y directions and 4 cells in the z direction. Specimens were first made by 3D printing by using a fused deposition modeling printer with acrylonitrile–butadiene–styrene thermoplastic. Specimens were then tested under compression in the z direction under quasi-static conditions. Finite element analysis was used to model the compressive behavior of the different lattice structures. Results from both experiments and finite element models show that the strength of the lattice structures is greater when vertical members are present, and the SEA depends on the lattice geometry and not its mass.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Manufacturing of Ultra-Fine Particle Coal Fly Ash–A380 Aluminum Matrix Composites with Improved Mechanical Properties by Improved Ring Milling and Oscillating Microgrid Mixing

An experimental study is presented of ultra-fine coal fly ash (CFA) aluminum matrix composites produced by successive high-power ring milling of CFA, oscillating microgrid mixing of the CFA–aluminum melt, gravity casting and rapid cooling. Samples corresponding to different CFA concentrations and particle size distributions (1 μm average, or less) are produced and subjected to microstructural and mechanical characterization, including tensile, compressive, impact, hardness and wear testing. While the usual trade-off between increased strength and hardness and reduced ductility and toughness is observed, the obtained ultra-fine particle composites are confirmed to have overall improved mechanical properties compared to composites with larger size particles previously produced by ball milling.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Current activated reactive ultrafast joining (CARUJ) of silicon carbide

In this work we propose and demonstrate a novel approach for rapid fabrication of ceramic-ceramic joint assemblies, using sintered Silicon Carbide (SiC) as an initial example. Current Activated Reactive Ultrafast Joining (CARUJ) utilizes resistive heating of carbon-based materials to apply localized heat at or around the joint zone at heating rates of 101– 103 °C/min. CARUJ is used to fabricate SiC-SiC joints with a Si-SiC interface using minimal pressure (1–2 MPa) at time scales considerably shorter (several minutes opposed to hours) than conventional approaches for similar systems. The reaction of an interfacial precursor based on elemental silicon and carbon leads to in-situ SiC formation to produce a continuous and dense bond in a single step. Measured average joint strengths of roughly 15 MPa are achieved when tested in single lap offset (SLO) compressive shear. Optional additions of refractory metals such as molybdenum can be utilized to introduce secondary inclusions such as MoSi 2 within the joint interface. We further demonstrate SiC-SiC joining using Active Brazing Alloys (ABA) and proof of concept joining of tubular geometries. The localized and rapid heat application realizes a versatile material joining technique that could be extended for joining components at the plant site.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Modeling shockwaves and impact phenomena with Eulerian peridynamics

Most previous development of the peridynamic theory has assumed a Lagrangian formulation, in which the material model refers to an undeformed reference configuration. Here, an Eulerian form of material modeling is developed, in which bond forces depend only on the positions of material points in the deformed configuration. The formulation is consistent with the thermodynamic form of the peridynamic model and is derivable from a suitable expression for the free energy of a material. We show that the resulting formulation of peridynamic material models can be used to simulate strong shock waves and fluid response in which very large deformations make the Lagrangian form unsuitable. The Eulerian capability is demonstrated in numerical simulations of ejecta from a wavy free surface on a metal subjected to strong shock wave loading. The Eulerian and Lagrangian contributions to bond force can be combined in a single material model, allowing strength and fracture under tensile or shear loading to be modeled consistently with high compressive stresses. Furthermore, we demonstrate this capability in numerical simulation of bird strike against an aircraft, in which both tensile fracture and high pressure response are important.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Additively manufactured β-Ti5553 with laser powder bed fusion: Microstructures and mechanical properties of bulk and lattice parts

Ti5553 (Ti-5Al-5Mo-5V-3Cr wt%) is a titanium alloy widely used for its high strength-to-weight ratio and good formability at elevated temperatures. Unlike Ti-6Al-4V, Ti5553 does not undergo martensitic transformation, preventing cracking of brittle martensite upon rapid cooling. This makes it a strong candidate for additive manufacturing (AM), particularly laser powder bed fusion (L-PBF). L-PBF offers the unique opportunity to make fine lattice structures to reduce component weight. Despite the growing field of AM, there have been limited studies on L-PBF Ti5553 lattices and how their properties differ from the bulk. Here the present work addresses this knowledge gap by investigating microstructures and properties of L-PBF bulk and lattice parts and the effect of post L-PBF heat treatments. Electron microscopy and mechanical testing show that the high dislocation density formed during L-PBF increases bulk part’s yield strength by approximately 100 MPa compared to the conventional alloy. Digital image correlation during compression testing of octet truss lattices reveals a layer-by-layer failure mode. Compared to the bulk, the lattice contains copious ω nanoprecipitation, weaker <001> texture, smaller average grain sizes, and larger content of high-angle grain boundaries. These features elicit differences in Taylor factor distributions for the lattice depending on load direction, underlining challenges in predicting lattice mechanical response based on bulk properties. By examining the processing-structure-property relationships in the bulk and lattice, the present results delineate their microstructural and mechanical differences and establish a benchmark for the future design applications of L-PBF Ti5553.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Correlating viscosity and die swell in 3D printing of polyphenylsulfone: A thermo-mechanical optimization modus operandi

Additive manufacturing (AM) of polyphenylsulfone (PPSU), an amorphous high-performance polymer (HPP), has shown promise in exhibiting structural integrity for many applications. With thermoplastic material extrusion 3D printing, parts consisting of layered melts exhibited voids, where the adhesion quality and void size depend on the processing parameters implemented during printing. However, the structure-process-property (SPP) relationships between the thermal properties and rheological and mechanical behavior of AM PPSU are poorly understood. Here, in this study, a comprehensive analysis of the thermal, thermo-mechanical, and layer-by-layer build-up of PPSU is investigated and correlated with viscosity and extrudate die swell behavior with void fraction volume as confirmed by high-resolution x-ray computed tomography (XCT). Gas chromatography–mass spectrometry (GC–MS) pyrolysis confirmed PPSU composition and degradation at 480 °C, consistent with thermo-gravimetric analysis TGA. A 141% difference in viscosity was observed when processing temperatures increased from 350 °C to 400 °C. Likewise, extrudate die swell decreased with increasing temperatures, resulting in a 17% difference. Tensile and compressive properties confirmed that higher extruding temperatures resulted in lower porosity and higher mechanical strength. In general, higher extruding temperatures lower the viscosity to allow for stronger cohesion between layers; however, increasing the temperature too high results in a below unity extrudate die swell, reducing mechanical properties. Therefore, to optimize the mechanical integrity of 3D printed amorphous PPSU parts, an increase in the viscosity, near unity of the extrudate die swell, and tempered extrusion temperature are needed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Damage to Polystyrene Polymer Film by Shock Wave Induced Bubble Collapse

Metallic surfaces that are in contact with solutions are commonly used in numerous applications where these surfaces can be damaged by shock wave induced bubble collapse. Use of polymer films that coat such surfaces to prevent them from damage requires a better understanding of how much harm collapsing bubbles produce in the films. In this study, we report the results from coarse-grained molecular dynamics simulations to study the damage to polystyrene (PS) films coating a hard surface. The damage was caused by a collapsing nanobubble located in the proximity of the film and interacting with an impinging shock wave. This collapse produces a high-speed water jet that impacts the PS film with a greater force than the shock front and creates cavities/pits in the PS film. We observed that polymer molecules located in the jet vicinity undergo conformational extension in the direction perpendicular to the jet motion, while chain molecules in the rest of the film undergo compression. Furthermore, we also observed that damage to the film is sensitive to the strength of the shock wave.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Efficiency-optimized relativistic plasma harmonics for extreme fields

Bright harmonic radiation from relativistically oscillating laser plasmas offers a direct route for generating extreme electromagnetic fields. Theory predicts that under optimized conditions, the plasma medium can support strong spatiotemporal compression of laser energy in a coherent harmonic focus (CHF), delivering intensity boosts many orders of magnitude greater than the incident driving laser pulse. Although diffraction-limited performance (spatial compression) and attosecond phase locking (temporal compression) have been demonstrated experimentally, efficient coupling of relativistically intense laser pulse energy into the emitted harmonic cone has not been realized so far. Here we demonstrate that this highly nonlinear interaction can be tailored to deliver the maximum conversion efficiencies predicted from simulations. By fine-tuning the temporal profile of the driving laser on sub-picosecond (<10 −12 s) timescales, energies >9 mJ between the 12th and 47th harmonics are observed. These results are in agreement with the theoretically expected efficiency dependence on harmonic order, verifying that optimal conditions have been achieved in the generation process. This is the important final element required to achieve the expected intensity boosts from a CHF in experiments. Although obtaining spatiotemporal compression and optimal efficiency simultaneously remains challenging, the path to realizing extreme optical field strengths approaching the critical field of quantum electrodynamics (the Schwinger limit at >10 16 V cm −1 or >10 29 W cm −2 ) is now open, permitting all-optical studies of the quantum vacuum and new frontiers for intense attosecond science.

High-harmonic generation↗
DOE OSTI2019

Contaminant Cation Effect on Oxygen Transport through the Ionomers of Polymer Electrolyte Membrane Fuel Cells

We characterized the effects of cobalt (Co 2+ ) and other cation contaminants on the oxygen (O 2 ) transport properties of the PFSA ionomer used in polymer electrolyte membrane fuel cells (PEMFCs) and gained insight into the mechanisms by which contaminant cations inhibit O 2 transport. Such cations can be released by alloy catalysts and environmental conditions and pose a significant challenge to maintaining high current density performance with low platinum (Pt) loadings. We used a test cell capable of isolating the ionomer from the membrane electrode assembly (MEA), allowing for O 2 transport resistance (R O2 ) measurements using a limiting current technique. We contaminated ionomer membranes with Li + , Na + , Ni 2+ , Co 2+ , and Ce 3+ and found a general increase in R O2 for increased contamination levels and decreased water activity. In addition, our Co 2+ results indicated distinct concentration-dependent regimes. The other cation-form ionomers allowed us to separate the impacts of ion pair strength, multivalency, and reduced water uptake. We believe that these factors cause a more compressed hydrophilic domain and tortuous O 2 diffusion path, and a commensurate increase in R O2 . Lastly, we studied the impact of Co 2+ on an operating PEMFC and found an increase in R O2 consistent with the results of our isolated membrane tests.

25 ENERGY STORAGE↗
NASA NTRS1973

Shockwave-boundary layer interference heating analysis.

Interference heating correlations have been developed based on existing wind tunnel test data taken with simple configurations such as wedge/flat plate and compression corner models. For turbulent flow, peak interference heating was first correlated with shock strength (pressure ratio across shock wave) and then as a function of Reynolds number. The peak interference Stanton number was found to exhibit the same Reynolds number and Prandtl number characteristics as the Stanton number variation for undisturbed flow over a flat plate. Similar correlations were developed for laminar flow. Results indicated that for laminar flow at higher Reynolds number, the impinging shockwave may act as a boundary layer trip and cause boundary layer transition resulting in high interference heating. The correlations derived in this study can be used to scale wind tunnel model test data to a full-scale space vehicle at supersonic or hypersonic flight conditions.

Hung, F. T.↗
NASA NTRS1974

Advanced beaded and tubular structural panels. Volume 1: Design and analysis

A study was conducted to exploit the efficiency of curved elements in the design of lightweight structural panels under combined loads of axial compression, inplane shear, and bending. Data cover analytical procedures for optimum panel design, static strength analyses, results of panel design studies, and correlation of theory with test results.

Greene, B. E.↗