SEARCH · Search NASA

Results for “Control Room”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

All sources NASA NTRS DOE OSTI

DOE OSTI2019

Control of superconductivity in MgB 2 by ion bombardment

The superconducting properties of MgB 2 can be modified via controlled introduction of lattice defects by ion bombardment. Here, magnetometry and Raman spectroscopy are used to study~160 nm-thick MgB 2 films bombarded at room temperature with megaelectronvolt-energy He, Ar, or Xe ions. Ion bombardment leads to a monotonic reduction in the critical superconducting transition temperature, transition width, and critical current density. There is a clear collision cascade density effect, whereby radiation-induced changes, once normalized to the number of atomic displacements generated, are greater for heavier ions. The sharpening of the superconducting transition with increasing ion dose suggests improved homogeneity of irradiated films. The suppression of superconducting properties correlates with the growth of defect signatures revealed by Raman spectroscopy. Superconducting properties can be recovered by annealing at relatively low temperatures of 500 °C, even for films exposed to high doses of heavy ions. These results have direct implications for the performance of MgB 2 in radiation environments and understanding its defect-mediated superconductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2015

Electron-stimulated purification of platinum nanostructures grown via focused electron beam induced deposition

In this paper, platinum–carbon nanostructures deposited via electron beam induced deposition from MeCpPt(IV)Me 3 are purified during a post-deposition electron exposure treatment in a localized oxygen ambient at room temperature. Time-dependent studies demonstrate that the process occurs from the top–down. Electron beam energy and current studies demonstrate that the process is controlled by a confluence of the electron energy loss and oxygen concentration. Furthermore, the experimental results are modeled as a 2nd order reaction which is dependent on both the electron energy loss density and the oxygen concentration. Finally, in addition to purification, the post-deposition electron stimulated oxygen purification process enhances the resolution of the EBID process due to the isotropic carbon removal from the as-deposited materials which produces high-fidelity shape retention.

36 MATERIALS SCIENCE↗

NASA NTRS1975

Fractography of the high temperature hydrogen attack of a medium carbon steel

Microscopic fracture processes were studied which are associated with hydrogen attack of a medium carbon steel in a well-controlled, high-temperature, high-purity hydrogen environment. Exposure to a hydrogen pressure and temperature of 3.5 MN/m2 and 575 C was found to degrade room temperature tensile properties with increasing exposure time. After 408 hr, yield and ultimate strengths were reduced by more than 40 percent and elongation was reduced to less than 2 percent. Initial fissure formation was found to be associated with manganese rich particles, most probably manganese oxide, aligned in the microstructure during the rolling operation. Fissure growth was found to be associated with a reduction in carbide content of the microstructure and was inhibited by the depletion of carbon. The interior surfaces of sectioned fissures or bubbles exhibit both primary and secondary cracking by intergranular separation. The grain surfaces were rough and rounded, suggesting a diffusion-associated separation process. Specimens that failed at room temperature after exposure to hydrogen were found to exhibit mixed mode fracture having varying amounts of intergranular separation, dimple formation, and cleavage, depending on exposure time.

Melson, H. G.↗

NASA NTRS1981

Analysis, design, fabrication and testing of an optical tip clearance sensor

Analyses and the design, fabrication, and testing of an optical tip clearance sensor with intended application in aircraft propulsion control systems are reported. The design of a sensor test rig, evaluation of optical sensor components at elevated temperatures, sensor design principles, sensor test results at room temperature, and estimations of sensor accuracy at temperatures of an aircraft engine environment are discussed. Room temperature testing indicated possible measurement accuracies of less than 12.7 microns (0.5 mils). Ways to improve performance at engine operating temperatures are recommended. The potential of this tip clearance sensor is assessed.

Poppel, G. L.↗

NASA NTRS2002

Detection of biogenic CO production above vascular cell cultures using a near-room-temperature QC-DFB laser

We report the first application of pulsed, near-room-temperature quantum cascade laser technology to the continuous detection of biogenic CO production rates above viable cultures of vascular smooth muscle cells. A computer-controlled sequence of measurements over a 9-h period was obtained, resulting in a minimum detectable CO production of 20 ppb in a 1-m optical path above a standard cell-culture flask. Data-processing procedures for real-time monitoring of both biogenic and ambient atmospheric CO concentrations are described.

NASA Discipline Life Sciences Technologies↗

DOE OSTI2023

Microstructure and Elevated Temperature Flexure Testing of Tungsten Produced by Electron Beam Additive Manufacturing

Abstract Due to their superior high-temperature thermomechanical capabilities, sputter erosion durability, and excellent resistance to hydrogen isotopes, tungsten materials have garnered significant interest in fusion nuclear applications. However, low room-temperature ductility and complex machining strategies present significant challenges for traditional fabrication. Electron beam powder bed fusion (EB-PBF) shows promise in manufacturing pure tungsten via high thermal energy input, elevated build temperature, and a tightly controlled high-vacuum environment. This work explores the process, structure, and property relationship of pure tungsten fabricated by EB-PBF, where 99.8% relative density was achieved with reduced cracking by isolating the build substrate and optimizing the print parameter suite. Optical and electron imaging revealed that the microstructure contained equiaxed grains along the build direction, with subgrains present in all inspected grains. Flexural testing at ambient and elevated temperatures demonstrated high ductility at 900°C and flexural strength of 470 MPa at room temperature of additively manufactured tungsten.

Zhang, Haozhi↗

DOE OSTI2015

A ferromagnetic compound with anti-cancer proeprties for controlled drug delivery and imaging

New anticancer agents and modalities for their use are of great interest. Recent studies have demonstrated the presence of anti-cancer properties in salen derivatives. We found that an iron salen derivative, i.e., [Fe(salen)] 2 O, displays ferromagnetic order above room temperature and shows spontaneous field-dependent magnetization and hysteresis. Understanding of this magnetic property is provided by first-principles calculations based on structures obtained by X-ray crystallography. [Fe(salen)] 2 O exhibited potent anti-cancer properties against various cancer cell types and was readily attracted by even moderate-strength permanent magnets in vitro. We demonstrated that the delivery of [Fe(salen)] 2 O to melanoma tissues transplanted into the tails of mice using a permanent magnet leads to a robust decrease in tumor size. The local accumulation of [Fe(salen)] 2 O was visualized by MRI. Thus, [Fe(salen)] 2 O acted as an anti-cancer and MRI contrast compound that has a pharmacological effect that is delivered in a controlled manner, suggesting new strategies for anti-cancer drug development.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2024

Controlling magnon-photon coupling in a planar geometry

Abstract The tunability of magnons enables their interaction with various other quantum excitations, including photons, paving the route for novel hybrid quantum systems. Here, we study magnon-photon coupling using a high-quality factor split-ring resonator and single-crystal yttrium iron garnet (YIG) sphere at room temperature. We investigate the dependence of the coupling strength on the size of the sphere and find that the coupling is stronger for spheres with a larger diameter as predicted by theory. Furthermore, we demonstrate strong magnon-photon coupling by varying the position of the YIG sphere within the resonator. Our experimental results reveal the expected correlation between the coupling strength and the rf magnetic field. These findings demonstrate the control of coherent magnon-photon coupling through the theoretically predicted square-root dependence on the spin density in the ferromagnetic medium and the magnetic dipolar interaction in a planar resonator.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Adhesion of Self-Complementary, Sinusoidal Surfaces Fabricated Using Two-Photon Polymerization

Microscale, pick-and-place assembly is a non-lithographic assembly method poised to impact diverse fields including flexible electronics, microfluidics and robotics. However, a major technological challenge is the need to deterministically control adhesion between parts. Here, switchable adhesion involving 3D-printed, self-complementary surfaces is demonstrated. Mechanical properties of metasurfaces pressed against flat, rigid substrates are modeled using finite element methods. A series of flat slabs and metastructured slabs with 2D sinusoidal surfaces are printed using two-photon polymerization (2PP) of a shape-memory resin. The surface frequency of featured slabs was varied between $3.\bar3$ mm −1 and $26.\bar6$ mm −1 with similar amplitudes. Adhesion between printed metasurfaces and glass and between printed, self-complementary metasurfaces is studied above and below the cured resin’s glass transition temperature (∼45 °C). Simple heating of adhering surfaces to above 60 °C lowers adhesion, and compression of surfaces while above the glass transition temperature followed by cooling to room temperature elevates adhesion. The nominal adhesive strength between printed, self-complementary surfaces, as determined by the maximum observable pull-off stress, exceeds 3 MPa. Further tailoring complementary surfaces for adhesion control may facilitate microscale disassembly for recovery of components or precious metals.

amorphous materials↗

DOE OSTI2014

Controllable pneumatic generator based on the catalytic decomposition of hydrogen peroxide

This paper presents a novel compact and controllable pneumatic generator that uses hydrogen peroxide decomposition. A fuel micro-injector using a piston-pump mechanism is devised and tested to control the chemical decomposition rate. By controlling the injection rate, the feedback controller maintains the pressure of the gas reservoir at a desired pressure level. Thermodynamic analysis and experiments are performed to demonstrate the feasibility of the proposed pneumatic generator. Using a prototype of the pneumatic generator, it takes 6 s to reach 3.5 bars with a reservoir volume of 200 ml at the room temperature, which is sufficiently rapid and effective to maintain the repetitive lifting of a 1 kg mass.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2017

Nonpolar InGaN/GaN core–shell single nanowire lasers

We report lasing from nonpolar p-i-n InGaN/GaN multi-quantum well core–shell single-nanowire lasers by optical pumping at room temperature. The nanowire lasers were fabricated using a hybrid approach consisting of a top-down two-step etch process followed by a bottom-up regrowth process, enabling precise geometrical control and high material gain and optical confinement. The modal gain spectra and the gain curves of the core–shell nanowire lasers were measured using micro-photoluminescence and analyzed using the Hakki-Paoli method. Significantly lower lasing thresholds due to high optical gain were measured compared to previously reported semipolar InGaN/GaN core–shell nanowires, despite significantly shorter cavity lengths and reduced active region volume. Mode simulations show that due to the core–shell architecture, annular-shaped modes have higher optical confinement than solid transverse modes. Furthermore, the results show the viability of this p-i-n nonpolar core–shell nanowire architecture, previously investigated for next-generation light-emitting diodes, as low-threshold, coherent UV–visible nanoscale light emitters, and open a route toward monolithic, integrable, electrically injected single-nanowire lasers operating at room temperature.

36 MATERIALS SCIENCE↗

DOE OSTI2017

Mechanical Analysis of the Short Model Magnets for the Nb $_{3}$Sn Low-$\beta$ Quadrupole MQXF

During the development of MQXF, the new Nb 3 Sn quadrupole to be used in the large hadron collider (LHC) inner triplets for the High Luminosity upgrade, three short models were tested: MQXFS1, MQXFS3, and MQXFS5. These models differ in the use of thin or thick laminations for the iron components, in the coil design, and in the superconductive strands, rod restack process (RRP) or powder in tube (PIT). In the MQXF design, the azimuthal prestress is provided at room temperature by means of the bladder-key technology, and it is further increased during the cooldown by the differential thermal contraction of the various components. Four aluminum rods provide the longitudinal prestress. Both systems allow for a flexible control of the amount of prestress applied. As a consequence, it was possible to test the models exploring different azimuthal and longitudinal prestress conditions, in an attempt to understand their impact on the magnet performances. Here, this paper studies the mechanical behavior of these short models, also providing the strain and stresses measured by means of strain gauges installed on the aluminum shell, on the winding poles and on the rods. Finally, the paper compares the measures with the results from finite element (FE) models.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2016

Influence of tungsten fiber’s slow drift on the measurement of G with angular acceleration method

In the measurement of the gravitational constant G with angular acceleration method, the equilibrium position of torsion pendulum with tungsten fiber undergoes a linear slow drift, which results in a quadratic slow drift on the angular velocity of the torsion balance turntable under feedback control unit. The accurate amplitude determination of the useful angular acceleration signal with known frequency is biased by the linear slow drift and the coupling effect of the drifting equilibrium position and the room fixed gravitational background signal. We calculate the influences of the linear slow drift and the complex coupling effect on the value of G, respectively. The result shows that the bias of the linear slow drift on G is 7 ppm, and the influence of the coupling effect is less than 1 ppm.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

NASA NTRS2020

The Spaceport Command and Control System Security Assessor Project

This Summer, I worked as a National Aeronautics and Space Administration (NASA) Internships and Fellowships (NIF) intern under my mentor, Jill Giles within the Software Engineering Branch. Within this project, I worked alongside the Cyber Security branch to identify a list of Commercial Off the Shelf (COTS) software to analyze, research, and gain insight about potential vulnerabilities within the software that could become a threat of attack. After identifying the list of COTS software, my team and I used Microsoft Excel to create a worksheet to easily organize and design a questionnaire about the software. Security reports weregiven to us to identify the software used on the machines in the firing rooms. With these reports, we created a script that would populate the database with the software information to identify potential security weaknesses of COTS software.The goal of the project was to produce a final report, summarizing the most vulnerable launch control system servers and configurations and document vulnerabilities, residual risk, likelihood, and consequence. This project is important for the Cyber Security and Information Technology branches because it will identify security weaknesses and help to mitigate risk. From the Spaceport Command and Control System Security Assessor Project, I learned how to properly identify weaknesses and vulnerabilities within software and how to mitigate the risks within the software. This project also taught me how to create databases using scripts and input files.

Destani Satora Van Arsdalen↗

DOE OSTI2018

Tribological Performance of Ni{sub 3}Al Matrix Composites Synthesized by Laser Melt Deposition Under Different Scanning Velocities

In order to study the effect of scanning velocity on the microstructure and tribological properties of Ni{sub 3}Al matrix composites containing graphene nanoplatelets (NGs), a series of NG samples are successfully synthesized by laser melt deposition under the various scanning velocities from 300 to 500 mm s{sup −1}. The sliding friction tests of NG against GCr15 steel balls are carried out under 10 N and 0.2 m s{sup −1} at room temperature. The microstructures, tribological properties and wear mechanisms of the NG samples are analyzed. The results show that the scanning velocity can be optimized to effectively control the surface hardness and relative density, as well as tribological performance of NG. The NG sample synthesized under scanning velocity of 450 mm s{sup −1} has a dense and fine microstructure as well as excellent properties such as higher relative density (98.6%), lower friction coefficient (0.23) and wear rate (5.5 × 10{sup −6} mm{sup 3} N{sup −1} m{sup −1}). The lower substrate layer with dense and stable structure plays an important role in supporting the upper glaze layer with rich graphene and oxides, as well as nanocrystalline structure, which contributes to the excellent friction-reducing and wear resistance performances of NG. The research results could be used to guide the selection of suitable scanning velocity and study the wear mechanisms of NG for having excellent tribological performance.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2019

An Optimization Platform Based on Coupled Indoor Environment and HVAC Simulation and its Application in Optimal Thermostat Placement

Model-based optimization can help improve the indoor thermal comfort and energy efficiency of Heating, Ventilation and Air Conditioning (HVAC) systems. The models used in previous optimization studies either omit the dynamic interaction between indoor airflow and HVAC or are too slow for model-based optimization. To address this limitation, we propose an optimization methodology using coupled simulation of the airflow and HVAC that captures the dynamics of both systems. We implement an optimization platform using the coupled models of a coarse grid Fast Fluid Dynamics model for indoor airflow and Modelica models for HVAC which is linked to the GenOpt optimization engine. Then, we demonstrate the new optimization platform by studying the optimal thermostat placement in a typical office room with a VAV terminal box in the design phase. After validating the model, we perform an optimization study, in which the VAV terminal box is dynamically controlled, and find that our optimization platform can determine the optimal location of thermostat to achieve either best thermal comfort or least energy consumption, or the combined. Finally, the time cost for performing such optimization study is about 6.2 h, which is acceptable in the design phase.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2021

Vapor Pressures of RDX and HMX Explosives Measured at and Near Room Temperature: 1,3,5-Trinitro-1,3,5-triazinane and 1,3,5,7-Tetranitro-1,3,5,7-tetrazocane

Knowing accurate saturated vapor pressures of explosives at ambient conditions is imperative to provide realistic boundaries on available vapor for ultra-trace detection. In quantifying vapor content emanating from low-volatility explosives, we observed discrepancies between the quantity of explosive expected based on literature vapor pressure values and the amount detected near ambient temperatures. Most vapor pressure measurements for low-volatility explosives, such as RDX (1,3,5-trinitro-1,3,5-triazinane) and HMX (1,3,5,7-tetranitro-1,3,5,7-tetrazocane), have been made at temperatures far exceeding 25 °C and linear extrapolation of these higher temperature trends appears to underestimate vapor pressures near room temperature. Our goal was to measure vapor pressures as a function of temperature closer to ambient conditions. We used saturated RDX and HMX vapor sources at controlled temperatures to produce vapors that were then collected and analyzed via atmospheric flow tube-mass spectrometry (AFT-MS). The parts-per-quadrillion (ppqv) sensitivity of AFT-MS enabled measurement of RDX vapor pressures at temperatures as low as 7 °C and HMX vapor pressures at temperatures as low as 40 °C for the first time. Furthermore, these vapor pressures were corroborated with analysis of vapor generated by nebulizing low concentration solutions of RDX and HMX. We report updated vapor pressure values for both RDX and HMX. Based on our measurements, the vapor pressure of RDX at 25 °C is 3 ± 1 x 10-11 atm (i.e. 30 parts per trillion by volume, pptv), the vapor pressure of HMX is 1.0 ± 0.6 x 10-14 atm (10 ppqv) at 40 °C and, with extrapolation, HMX has a vapor pressure of 1.0 ± 0.6 x 10-15 atm (1.0 ppqv) at 25 °C.

RDX, HMX, explosives, vapor pressure, vapor detect↗

DOE OSTI2014

Integrated Nano-Domains of Disordered and Ordered Spinel Phases in LiNi 0.5 Mn 1.5 O 4 for Li-Ion Batteries

Recent calculations and experimental data suggest that understanding the local ordering behavior of Ni/Mn will be critical to optimize the electrochemical properties of LiNi 0.5 Mn 1.5 O 4 (LNMO) high voltage spinel. In this study, we systematically controlled the evolution of Ni and Mn ordering in LNMO samples by annealing them at 700 °C in air for different dwelling times, followed by quenching to room temperature. The long- and short-range ordering behavior of Ni and Mn were analyzed by combining neutron powder diffraction, X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and Fourier transform infrared spectroscopy (FT-IR) data. The results show that the fraction of ordered phase increases rapidly during initial annealing at 700 °C for 6 h, and accompanied by decreasing amounts of secondary phases. Annealing longer than 6 h led to the growth in size of ordered domains (i.e., increased segregation of ordered and disordered domains) along with a slow increase in the fraction of ordered phase. The dependence of open circuit voltages (OCVs) of the LNMO on the degree of ordering agrees well with recent calculations using the density functional theory. The increase in the degree of ordering increases the open circuit voltage (OCV) and the initial capacity but reduces cycle life and rate capability. The LNMO delivered optimal battery performances (capacity, cycle life, and rate capability) after annealing at 700 °C for 2 h. This partially ordered sample showed the respective advantages from both disordered and ordered spinels: better spinel-phase purity (thus, higher initial capacity) from the ordered LNMO and better cycle life and rate capability from the disordered LNMO.

25 ENERGY STORAGE↗