Search NASA⌕ Search

SEARCH · Search NASA

Results for “Design pattern”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

Skyrmion based microwave detectors and harvesting

Magnetic skyrmions are topologically protected states that are very promising for the design of the next generation of ultra-low-power electronic devices. In this letter, we propose a magnetic tunnel junction based spin-transfer torque diode with a magnetic skyrmion as ground state and a perpendicular polarizer patterned as nano-contact for a local injection of the current. The key result is the possibility to achieve sensitivities (i.e., detection voltage over input microwave power) larger than 2000 V/W for optimized contact diameters. We also pointed out that large enough voltage controlled magnetocrystalline anisotropy could significantly improve the sensitivity. Our results can be very useful for the identification of a class of spin-torque diodes with a non-uniform ground state and to understand the fundamental physics of the skyrmion dynamical properties.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Poster - 38: On the physical and dosimetric properties of 3D printed electron bolus fabricated using polylactic acid

Purpose: 3D printing technology could simplify and improve electron bolus fabrication. The purpose of this study was to characterize the density, dimensional accuracy, uniformity, and attenuation of PLA boluses fabricated with a low-cost 3D printer. Methods: Several solid square slabs were printed with specific requested dimensions and 100% infill using different fill patterns. These pieces were imaged using an x-ray flat panel imager in order to check for uniformity of the prints. Percentage depth doses (PDDs) were measured downstream of the slabs in solid water using a parallel plate chamber and compared to measurements in water in order to characterize attenuation. The dimensions of the PLA slabs were measured using digital calipers. The slabs were also weighed to find their density. Results: The fill pattern used to create boluses can affect the attenuation of the bolus. Fill patterns should be chosen carefully and quality assurance should be done for each printed piece. PLA causes the electron PDD to shift towards shallower depths, compared to water, by 1.7 mm for each centimeter of PLA. Agreement with design dimensions was within 1 mm in the plane of the printer bed, and within 1/3 of a millimeter (roughly the thickness of a single layer), perpendicular to the printer bed. Average density was in the range 1.20 – 1.22. Conclusions: 3D printing shows great promise for use in fabricating electron bolus. This work indicates that printed PLA can be a suitable material provided the increased attenuation is properly accounted for.

60 APPLIED LIFE SCIENCES↗

Final Technical Report: Application of in situ Neutron Diffraction to Understand the Mechanism of Phase Transitions

In this research, phase transitions in the bulk electrodes for Li-ion batteries were investigated using neutron diffraction (ND) as well as neutron imaging techniques. The objectives of this research is to design of a novel in situ electrochemical cell to obtain Rietveld refinable neutron diffraction experiments using small volume electrodes of various laboratory/research-scale electrodes intended for Li-ion batteries. This cell is also to be used to investigate the complexity of phase transitions in Li(Mg) alloy electrodes, either by diffraction or by neutron imaging, which occur under electrochemical lithiation and delithiation, and to determine aspects of phase transition that enable/limit energy storage capacity. Additional objective is to investigate the phase transitions in electrodes made of etched micro-columns of silicon and investigate the effect of particle/column size on phase transitions and nonequilibrium structures. An in situ electrochemical cell was designed successfully and was used to study the phase transitions under in-situ neutron diffraction in both the electrodes (anode/cathode) simultaneously in graphite/LiCoO 2 and in graphite/LiMn 2 O 4 cells each with two cells. The diffraction patterns fully validated the working of the in situ cell. Additional experimental were performed using the Si micro-columnar electrodes. The results revealed new lithiation phenomena, as evidenced by mosaicity formation in silicon electrode. These experiments were performed in Vulcan diffractometer at SNS, Oak Ridge National Laboratory. In parallel, the spatial distribution of Li during lithiation and delithiation processes in Li-battery electrodes were investigated. For this purpose, neutron tomographic imaging technique has been used for 3D mapping of Li distribution in bulk Li(Mg) alloy electrodes. It was possible to observe the phase boundary of Li(Mg) alloy indicating phase transition from Li-rich BCC β-phase to Li-lean α-phase. These experiments have been performed at CG-1D Neutron Imaging Prototype Station at SNS.

25 ENERGY STORAGE↗

Sodium Freezing and Remelting Tests in FY 2018

In FY 2017 and FY 2018, a total of thirteen tests were successfully performed in the Sodium Freezing and Remelting test facility. Each new test was carefully designed based upon the results and findings of the previous test to investigate the effects of different factors on the sodium freezing phenomena, including dissolved Ar cover gas versus vacuum, test section cooling rate during freezing, different freezing patterns (e.g., from the free surfaces inward toward the center versus from the center toward the free surfaces), and Ar cover gas pressure. The freezing results were found to depend upon a combination of phenomena. As more tests were conducted and lessons learned, the conduct of the tests improved. In particular, the last three experiments, Tests 11 through 13, may be singled out as providing representative data under well controlled conditions. The maximum stresses arising from sodium freezing are measured to be quite mild. In the tests, a maximum strain change of 60 radial micro strains was measured, equivalent to a stress/negative pressure of 77 psi. This mild maximum stress is thought to reflect the low yield stress of solid sodium near the freezing temperature. Evidence for yielding of solid sodium is provided by the visual observation of a depression in the frozen sodium free surface inside of the sodium reservoir in one test. It is thought that contraction of sodium in the test section during freezing pulled downward on the frozen sodium at the free surface creating the depression. The authors are not aware of any data for the yield stress of solid sodium or the stress versus strain behavior of solid sodium (sodium is not a structural material). It is thus not possible to directly compare with the solid sodium yield strength. However, stress versus strain data at different temperatures up to the freezing temperature are available for solid lithium which is also a alkali metal and has a low yield strength similar to the maximum stresses determined from the Sodium Freezing and Remelting tests providing support for the interpretation of the results in terms of yielding of solid sodium. This is a good result for Sodium-Cooled Fast Reactors and sodium facilities. The maximum stress due to frozen sodium pulling inward upon a structural wall wetted by sodium and to which the sodium adheres will be limited by the low sodium yield stress. Argon has a significant solubility in sodium. Cavitation due to nucleation of dissolved argon can offset the effects of sodium thermal contraction and alleviate the formation of stress/negative pressure. This is also a good result for Sodium-Cooled Fast Reactors and sodium facilities that operate with an argon cover gas. In the tests, it was found that due to the cavitation, the maximum measured strain change during sodium freezing was limited to 10 axial micro strains, or equivalently 55 psi of negative pressure.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Understanding the Hierarchy of Dense Subgraphs in Stationary and Temporally Varying Setting

Graphs are widely used to model relationships in a wide variety of domains such as sociology, bioinformatics, infrastructure, the WWW, to name a few. One of the key observations is that while real-world graphs are often globally sparse, they are locally dense. In other words, the average degree is often quite small (say at most 10 in a million vertex graph), but vertex neighborhoods are often dense. Finding dense subgraphs is a critical aspect of graph mining It has been used for finding communities and spam link farms in web graphs, graph visualization, real-time story identification, DNA motif detection in biological networks, finding correlated genes, epilepsy prediction, finding price value motifs in financial data, graph compression, distance query indexing, and increasing the throughput of social networking site servers. However, most standard formulations of this problem (like clique, quasi-clique, k-densest subgraph) are NP-hard. Furthermore, current dense subgraph finding algorithms usually optimize some objective, and only find a few such subgraphs without providing any structural relations, whereas the goal is rarely to find the "true optimum," but to identify many (if not all) dense substructures, understand their distribution in the graph, and ideally determine relationships among them. In this project, we first aim to devise algorithms and provide 3 implementations with nice visualizations to find the hierarchy between dense subgraphs, and then understand the structure of the hierarchy to gain more insight on the hidden patterns in real-world networks. Another important aspects in graph analysis is the temporal nature of networks. Networks evolve over time and in many applications data arrives at a high velocity, and thus it is important to design algorithms that can process data efficiently. We report three main results towards identifying dense structures in large evolving graphs. First, we will show how the hierarchical connectedness structure can be maintained efficiently, where connectedness is defined by increasing levels of connectivity strength. Next, we present dense structure can be identified in bipartite graphs without building projection graphs. And finally, we present a new method for peeling algorithms This new approach avoids sequential nature of peeling algorithms and is amenable to parallelization, which is crucial for processing high velocity data.

97 MATHEMATICS AND COMPUTING↗

First Performance Results of the PIP2IT MEBT 200 Ohm Kicker Prototype

The PIP-II project is a program to upgrade the Fermilab accelerator complex. The PIP-II linac includes a 2.1 MeV Medium Energy Beam Transport (MEBT) section that incorporates a unique chopping system to perform arbitrary, bunch-by-bunch removal of 162.5 MHz structured beam. The MEBT chopping system will consist of two identical kickers working together and a beam absorber. One design of two having been proposed has been a 200 Ohm characteristic impedance traveling wave dual-helix kicker driven with custom designed high-speed switches. This paper reports on the first performance results of one prototype kicker built, installed and tested with beam at the PIP-II Injector Test (PIP2IT) facility. The helix deflector design details are discussed. The electrical performance of the high-speed switch driver operating at 500 V bias is presented. Tests performed were chopping beam at 81.25 MHz for microseconds as well as with a truly arbitrary pattern for 550 $\mu$s bursts having a 45 MHz average switching rate and repeating at 20 Hz.

43 PARTICLE ACCELERATORS↗

MORPHODYNAMIC MODELING OF FLOW AND SEDIMENT TRANSPORT OVER LOW-HEAD, RUN-OF-RIVER DAMS

Low-head or Run-of-River (RoR) dams exist on all types of rivers throughout the United States, yet the exact mechanisms of how sediment moves around the structures have not been well researched. Due to the increasing use of RoR dams in small hydroelectric projects, there is a need to better understand the controlling factors of how sediment passes over these dams. A one-dimensional morphodynamic model was developed to investigate the effects of RoR dams on channel morphology over long time scales. The model solves the gradually varied flow equations to compute the flow field in the vicinity of the dam, computes grain-size-specific sediment transport rates, and uses sediment mass conservation and vertical storage bookkeeping to calculate the evolution of bed elevation, the bed surface grain-size distribution, and the vertical pattern of stratigraphy. The model’s hydraulic calculations were calibrated using data collected from a series of flume experiments performed with a model RoR dam to better capture the non-hydrostatic flow over a dam. Numerical experiments designed to investigate how the grain-size distribution of the sediment supply rate, flow rate (steady and unsteady), and dam height act as controls on sediment passage over RoR dams were conducted using parameters reported in the literature for a RoR dam in northern Delaware.These one-dimensional simulations were complemented with a few simulations using, a two-dimensional morphodynamic model, Nays2DH. The 1D simulation results show that the stored sediment upstream of RoR dams does depend on the sediment supply, dam height, grain-size and flow discharge. Once sedimentation in the reservoir has reached equilibrium, high flow events will reduce or scour the sediment while lower flows will typically increase the amount of sediment behind the dam. Finally, a dam that stores more sediment will have greater downstream effects in terms of changes to grain-sizes and bed elevation due to the increased time it ii takes to pass sediment over the dam and reach an equilibrium condition on the upstream side of the dam.

13 HYDRO ENERGY↗

Optimization of {sup 6}LiF:ZnS(Ag) Scintillator Light Yield Using Geant4

Neutrons provide an effective tool to probe materials structure. Neutron diffraction is a method to determine the atomic and magnetic structure of a material based on neutron scattering. By this method a collimated incident beam of thermal neutrons heat the examined sample and based on the obtained diffraction pattern information on the structure of the material is provided. Research for developing a novel cold neutron detector for Chromatic Analysis Neutron Diffractometer Or Reflectometer (CANDOR) is underway at the NIST center for neutron research. The system unique design is aimed to provide over ten times fold faster analysis of materials than conventional system. In order to achieve the fast analysis a large number of neutron detectors is required. A key design constraint for this detector is the thickness of the neutron sensitive element. This is met using {sup 6}LiF:ZnS(Ag) scintillation material with embedded wavelength shifting (WLS) fibers conducting scintillation light to silicon photomultiplier photo-sensors. The detector sensitivity is determined by both the neutron capture probability ({sup 6}Li density) and the detectable light output produced by the ZnS(Ag) ionization, the latter of which is hindered by the fluorescence absorption of the scintillation light by the ZnS. Tradeoffs between the neutron capture probability, stimulated light production and light attenuation for determining the optimal stoichiometry of the {sup 6}LiF and ZnS(Ag) as well as the volume ratio of scintillator and fiber. Simulations performed using the GEANT4 Monte Carlo package were made in order to optimize the detector design. GEANT4 enables the investigation of the neutron interaction with the detector, the ionization process and the light transfer process following the nuclear process. The series of conversions required for this detector were modelled: - A cold neutron enters the sensor and is captured by {sup 6}Li in the scintillator mixture ({sup 6}Li (n,α) {sup 3}H reaction). The study of investigating the capture process probability for neutron energy of 5.1 meV to 2.27 meV (4 - 6 A) is presented. - Alpha particles and tritons travel for a few microns in the scintillation material (α ∼0.007 mm, T ∼0.04 mm) losing energy and ionizing the ZnS. The mean free path of the two particles in each of the component materials and the complete compound was investigated. - The ionization of the ZnS(Ag) scintillation material produces blue light photons with luminescence wavelength of 450 nm. The amount of light output produced for different grain sizes of ZnS is discussed. - A large portion of the scintillation photons are reabsorbed during their passage through the scintillation material. - The blue photons that reach the WLS fibers are absorbed by fluorescent dye and are re-emitted as green photons, conducted by the fiber to the SiPM photo-sensor. This work presents the CANDOR unique design and its design constrains, the results measured by the ultra-thin {sup 6}LiF:ZnS(Ag)-based neutron detector versus the simulation results for several binder concentrations. The light measurement attenuation results along with the measured stopping power were utilized to predict the sensitivity results of configuration with different ZnS grain size, weight ratios and fibers geometry (number and location). The simulations enable to optimize the final sensor design. This design successfully achieved both the high gamma rejection with a sensitive and accurate neutron event detection of 80 percent. (authors)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Open-loop correction for an eddy current dominated beam-switching magnet

A beam-switching magnet and the pulsed power supply it requires have been developed for the Japan Proton Accelerator Research Complex. To switch bunched proton beams, the dipole magnetic field must reach its maximum value within 40 ms. In addition, the field flatness should be less than 5 × 10{sup −4} to guide each bunched beam to the designed orbit. From a magnetic field measurement by using a long search coil, it was found that an eddy current in the thick endplates and laminated core disturbs the rise of the magnetic field. The eddy current also deteriorates the field flatness over the required flat-top period. The measured field flatness was 5 × 10{sup −3}. By using a double-exponential equation to approximate the measured magnetic field, a compensation pattern for the eddy current was calculated. The integrated magnetic field was measured while using the newly developed open-loop compensation system. A field flatness of less than 5 × 10{sup −4}, which is an acceptable value, was achieved.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Echo state network for coarsening dynamics of charge density waves

An echo state network (ESN) is a type of reservoir computer that uses a recurrent neural network with a sparsely connected hidden layer. Compared with other recurrent neural networks, one great advantage of ESN is the simplicity of its training process. Yet, despite the seemingly restricted learnable parameters, ESN has been shown to successfully capture the spatial-temporal dynamics of complex patterns. Here we build an ESN to model the coarsening dynamics of charge-density waves (CDWs) in a semiclassical Holstein model, which exhibits a checkerboard electron density modulation at half-filling stabilized by a commensurate lattice distortion. The inputs to the ESN are local CDW order parameters in a finite neighborhood centered around a given site, while the output is the predicted CDW order of the center site at the next time step. Special care is taken in the design of couplings between hidden layer and input nodes to ensure lattice symmetries are properly incorporated into the ESN model. Since the model predictions depend only on CDW configurations of a finite domain, the ESN is scalable and transferrable in the sense that a model trained on dataset from a small system can be directly applied to dynamical simulations on larger lattices. Furthermore, our work opens avenues for efficient dynamical modeling of pattern formations in functional electron materials.

2-dimensional systems↗

Nanoscale Ferroelectric Control of Novel Electronic States in Layered Two-Dimensional Materials (Final Report)

In this DOE Early Career project “Nanoscale Ferroelectric Control of Novel Electronic States in Layered Two-Dimensional Materials,” the PI’s group has combined ferroelectric field effect with nanoscale domain imaging and writing to design the electronic and optical properties of two-dimensional (2D) van der Waals materials, including graphene and transition metal dichalcogenides MoS2 and ReS2. The van der Waals materials have been prepared into field effect transistor (FET) devices with ferroelectric gates. Through domain patterning in a ferroelectric polymer PVDF-TrEF top-gate via conductive atomic force microscopy, the team has created programmable Schottky junctions in monolayer MoS 2 , where both barrier height and I-V rectifying polarity can be reconfigured. The transport anisotropy of monolayer to few-layer ReS 2 has been mapped out by defining the entire channel into an insulating state and creating nanoscale conducting paths along different directions through domain writing in the ferroelectric top-gate. The result shows that the conductivity along and perpendicular to the Re-chain can differ by >5.5x10 4 . Theoretical modeling points to the band origin of the transport anomaly and reveals the emergence of a flat band in few-layer ReS 2 . The interfacial epitaxial relation between ReS 2 and PVDF-TrFE further promotes the formation of close-packed, highly ordered PVDF-TrFE nanowires with width of 35 nm and 10 nm. Nonvolatile modulation of quantum Hall effect has been achieved in graphene FETs with a ferroelectric oxide Ba 0.4 Sr 0.6 TiO 3 back-gate. Scattering from the remote surface optical phonon in Ba 0.4 Sr 0.6 TiO 3 limits the room temperature mobility of graphene to be about 3x10 4 cm 2 /Vs. Steep-slope switching has been achieved in MoS 2 FETs back-gated by polycrystalline Pb(Zr,Ti)O 3 , which signals a static-state negative capacitance mode without involving an additional dielectric layer. Piezoresponse force microscopy studies show that the sub-threshold swing can be well correlated with the domain wall density in Pb(Zr,Ti)O 3 . The team also observes an unconventional filtering effect of the second harmonic generation response at the MoS 2 /Pb(Zr,Ti)O 3 heterointerface, which can be accounted for by the alignment between one of the polar axes of MoS 2 and the chiral dipole rotation at the surface of domain wall in Pb(Zr,Ti)O 3 . The research supported by this DOE grant has significantly advanced the fundamental understanding and functional design of ferroelectric/2D van der Waals heterostructures for their implementation towards energy applications.

36 MATERIALS SCIENCE↗

Hierarchical assemblies of polypeptoids for rational design of advanced functional nanomaterials

Polypeptoids (poly-N-substituent glycines) are a class of highly tailorable peptidomimetic polymers. Polypeptoids have identical backbones as polypeptides (poly-C-substituent glycines), but sidechains of polypeptoids are appended to backbone nitrogen rather than α-carbon of polypeptides. As a result, peptoid backbone lacks of chirality and hydrogen bond donors. This unique structure gives polypeptoids a combined merit of both high stability as synthetic polymers and biocompatibility as biopolymers. In addition, peptoid sequences can be engineered precisely to assemble specific crystalline patterns such as spheres, fibers, ribbons, tubes, and sheets, which shows promising potentials of polypeptoids for different applications such as antimicrobials, catalysts, drug delivery, and templating inorganic materials. In this review, we summarize recent investigations into hierarchical self-assembly pathways and molecular structures of peptoid crystals that are of interest as templates for fabricating functional materials for potential biomedical, biochemical, and bioengineering applications. Furthermore, this review provides a summary of recent experimental and computational studies of polypeptoid assembly in solution and solid-liquid interfaces, current achievements in the field, and discusses future challenges and opportunities for the rational design of self-assembled polypeptoid nanomaterials.

36 MATERIALS SCIENCE↗

Apparatus for real-time acoustic imaging of Rayleigh-Bénard convection

We have successfully designed, built and tested an experimental apparatus which is capable of providing the first real-time ultrasound images of Rayleigh-B\'{e}nard convection in optically opaque fluids confined to large aspect ratio experimental cells. The apparatus employs a modified version of a commercially available ultrasound camera to capture images (30 frames per second) of flow patterns in a fluid undergoing Rayleigh Bénard convection. The apparatus was validated by observing convection rolls in 5cSt polydimethylsiloxane (PDMS) polymer fluid. Our first objective, after having built the apparatus, was to use it to study the sequence of transitions from diffusive to time--dependent heat transport in liquid mercury. The aim was to provide important information on pattern formation in the largely unexplored regime of very low Prandtl number fluids. Based on the theoretical stability diagram for liquid mercury, we anticipated that straight rolls should be stable over a range of Rayleigh numbers, between 1708 and approximately 1900. Though some of our power spectral densities were suggestive of the existence of weak convection, we have been unable to unambiguously visualize stable convection rolls above the theoretical onset of convection in liquid mercury. Currently, we are seeking ways to increase the sensitivity of our apparatus, such as (i) improving the acoustic impedance matching between our materials in the ultrasound path and (ii) reducing the noise level in our acoustic images due to turbulence and cavitation in the cooling fluids circulating above and below our experimental cell. If we are able to convincingly improve the sensitivity of our apparatus, and we still do not observe stable convection rolls in liquid mercury, then it may be the case that the theoretical stability diagram requires revision. In that case, either (i) straight rolls are not stable in a large aspect ratio cell at the Prandtl numbers associated with liquid mercury, or (ii) they are stable, but not in the region of the stability diagram which has been studied by this experimenter. Our second objective was to use the apparatus to study other optically opaque fluids. To this end, we have obtained the first ultrasound images of Rayleigh-Bénard convection in a ferrofluid (EFH1). This project has provided a vehicle for the scientific training of five undergraduate research assistants during the past four years. It allowed students at Wisconsin Lutheran College, a small undergraduate liberal arts college in Milwaukee, to become directly involved in a significant scientific project from its inception through publication of scientific results. The funding of this project has also strengthened the research and teaching infrastructure at the Wisconsin Lutheran College in three major ways. The project has funded the PI and his students in the design and construction of a major piece of scientific apparatus which is capable of performing novel studies of Rayleigh-Bénard convection in opaque fluids. With the acquisition of this apparatus, we are able to embark on a broad research program to study problems in pattern formation in alloys, ferro-fluids, opaque gels, and liquid metals under thermal or magnetic stresses. This project has allowed the PI to purchase auxiliary equipment necessary for establishing a fluid dynamics research laboratory at the College. And this project has served as an impetus for the College to invest in a new machine shop in the basement of the Science Building at the College in order to support this, and other, scientific projects at the College. The PI has presented work funded by this grant at physics and engineering colloquia at a nearby university and at the keynote presentation at an undergraduate research symposium at Wisconsin Lutheran College. Also, the work was featured in local magazine and newspaper articles, and is described on the PI's research webpage. Such scientific outreach serves to advance the cause of science by making it interesting and accessible to a wider audience, and to bring attention to the work done by the Office of Basic Energy Sciences of the Department of Energy.

36 MATERIALS SCIENCE↗

Recent Progress of the Series-Connected Hybrid Magnet Projects

The National High Magnetic Field Laboratory (NHMFL) in Tallahassee, Florida has designed and is now constructing two Series Connected Hybrid (SCH) magnets, each connecting a superconducting outsert coil and a resistive Florida Bitter insert coil electrically in series. The SCH to be installed at the NHMFL will produce 36 T and provide 1 ppm maximum field inhomogeneity over a 1 cm diameter spherical volume. The SCH to be installed at the Helmholtz Center Berlin (HZB) in combination with a neutron source will produce 25 T to 30 T depending on the resistive insert. The two magnets have a common design for their cable-in-conduit conductor (CICC) and superconducting outsert coils. The CICC outsert coil winding packs have an inner diameter of 0.6 m and contribute 13.1 T to the central field using three grades of CICC conductors. Each conductor grade carries 20 kA and employs the same type of Nb{sub 3}Sn superconducting wire, but each grade contains different quantities of superconducting wires, different cabling patterns and different aspect ratios. The cryostats and resistive insert coils for the two magnets are different. This paper discusses the progress in CIC conductor and coil fabrication over the last year including specification, qualification and production activities for wire, cable, conductor and coil processing.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Pattern ANalytics To Support High-performance Exploitation and Reasoning (PANTHER)

Sandia researchers are developing analytic techniques that efficiently detect patterns in high-volume, noisy, remote sensing and other geospatial data, improving an analysts’ ability to detect possibly off-normal events in complex homeland security, nuclear weapons, and emerging threat environments. High-consequence, national security decisions rely on timely, comprehensive answers to complex questions, yet critical gaps in our approach to these questions remain. PANTHER addresses these gaps through fundamental research on: geospatial-temporal feature extraction via image segmentation and classification; geospatial-temporal graph algorithms and computational geometry; and domain-relevant models of human perception and cognition informing the design of analytic systems. PANTHER’s cross-disciplinary R&D approach uses fundamental science and mathematics to understand how to maximize decision systems through rethinking key aspects of geospatial data analysis. New methods in motion and trajectory analysis support both rapid search for known trajectories as well as rapid clustering and anomaly detection. Thus, the perceptual and visual load on users is reduced by providing pattern analytics with elegant visual cues to spatial and temporal characteristics.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Creating a spatial multi-criteria decision support system for energy related integrated environmental impact assessment

By their spatially very distributed nature, profitability and impacts of renewable energy resources are highly correlated with the geographic locations of power plant deployments. A web-based Spatial Decision Support System (SDSS) based on a Multi-Criteria Decision Analysis (MCDA) approach has been implemented for identifying preferable locations for solar power plants based on user preferences. The designated areas found serve for the input scenario development for a subsequent integrated Environmental Impact Assessment. The capabilities of the SDSS service get showcased for Concentrated Solar Power (CSP) plants in the region of Andalusia, Spain. The resulting spatial patterns of possible power plant sites are an important input to the procedural chain of assessing impacts of renewable energies in an integrated effort. The applied methodology and the implemented SDSS are applicable for other renewable technologies as well. - Highlights: • The proposed tool facilitates well-founded CSP plant siting decisions. • Spatial MCDA methods are implemented in a WebGIS environment. • GIS-based SDSS can contribute to a modern integrated impact assessment workflow. • The conducted case study proves the suitability of the methodology.

14 SOLAR ENERGY↗

A primer on artificial intelligence in plant digital phenomics: embarking on the data to insights journey

Artificial intelligence (AI) has emerged as a fundamental component of global agricultural research that is poised to impact on many aspects of plant science. In digital phenomics, AI is capable of learning intricate structure and patterns in large datasets. We provide a perspective and primer on AI applications to phenome research. We propose a novel human-centric explainable AI (X-AI) system architecture consisting of data architecture, technology infrastructure, and AI architecture design. We clarify the difference between post hoc models and 'interpretable by design' models. We include guidance for effectively using an interpretable by design model in phenomic analysis. We also provide directions to sources of tools and resources for making data analytics increasingly accessible. In conclusion, this primer is accompanied by an interactive online tutorial.

60 APPLIED LIFE SCIENCES↗