Search NASA⌕ Search

SEARCH · Search NASA

Results for “Experimental evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Zero-Boil-Off Tank (ZBOT) Experiment: Ground-Based Validation of Self-Pressurization and Pressure Control Two-Phase CFD Model

Integral to all phases of NASA's projected space and planetary expeditions is affordable and reliable cryogenic fluid storage for use in propellant or life support systems. Cryogen vaporization due to heat leaks into the tank from its surroundings and support structure can cause self-pressurization relieved through venting. This has led to a desire to develop innovative pressure control designs based on mixing of the bulk tank fluid together with some form of active or passive cooling to allow storage of the cryogenic fluid with zero or reduced boil-off. The Zero-Boil-Off Tank (ZBOT) Experiments are a series of small scale tank pressurization and pressure control experiments aboard the International Space Station (ISS) that use a transparent volatile simulant fluid in a transparent sealed tank to delineate various fundamental fluid flow, heat and mass transport, and phase change phenomena that control storage tank pressurization and pressure control in microgravity. The hardware for ZBOT-1 flew to ISS on the OA-7 flight in April 2017 and operations are planned to begin in September 2017, encompassing more than 90 tests. This paper presents preliminary results from ZBOT's ground-based research delineating both pressurization and pressure reduction trends in the sealed test tank. Tank self-pressurization tests are conducted under three modes: VJ heating, strip heating and simultaneous VJ and strip heating in attempt to simulate heat leaks from the environment, the support structure and both. The jet mixing pressure control studies are performed either from an elevated uniform temperature condition or from thermally stratified conditions following a self-pressurization run. Jet flow rates are varied from 2-25 cm/s spanning a range of jet Re number in laminar, transitional, and turbulent regimes and a range of Weber numbers covering no ullage penetration, partial penetration and complete ullage penetration and break-up (only in microgravity). Numerical prediction of a two-phase CFD model are compared to experimental 1g results to both validate the model and also indicate the effect of the residual non-condensable gas on evolution of pressure and temperature distributions in the tank during pressurization and pressure control.

microgravity evaporation condensatio↗
DOE OSTI2020

Magnetic Field Determination for Run 1 of the Fermilab Muon $g-2$ Experiment

The muon $g-2$ experiment at Fermilab aims to measure the anomalous magnetic moment of the muon, $a_{\mu}$, to a precision of 140 parts per billion (ppb). The measurement will shed light on the current $>$3$\sigma$ deviation between Standard Model calculations and the previous measurement made at Brookhaven National Laboratory, either resolving the discrepancy or confirming it to $>$5$\sigma$. In the muon $g-2$ experiment, muons are stored in a magnetic storage ring and their decays are observed. In order to reach the precision goal, the magnetic field experienced by the muons must be known with an uncertainty of \SI{70}{ppb} or less. To this end, the magnetic field was shimmed to unprecedented homogeneity. Two measurement systems are used to track the evolution of the magnetic field. This dissertation describes the motivations for the $g-2$ experiment, gives a brief overview of the experimental principles, introduces the magnetic field measurement hardware, describes the magnetic field shimming process, and presents an analysis of the magnetic field tracking for data collected in spring 2018 during run 1 of the Fermilab muon $g-2$ experiment.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

GSAS Tools

SAND2023-06684O GSAS Tools is a web application that manages user access to modeling and simulation tools and promotional material. This software, which is a spiking neural network (SNN) simulator, represents an SNN as a graph of stochastic differential equations and simulates the time-evolution of these equations. It has the capability of reading inputs from file and writing outputs to file, and generally supports experimentation, analysis, and algorithm development using SNNs. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

Noel, Todd↗
NASA NTRS2016

Rare Earth Element Partitioning in Lunar Minerals: An Experimental Study

The partitioning behavior of rare earth elements (REE) between minerals and melts is widely used to interpret the petrogenesis and geologic context of terrestrial and extra-terrestrial samples. REE are important tools for modelling the evolution of the lunar interior. The ubiquitous negative Eu anomaly in lunar basalts is one of the main lines of evidence to support the lunar magma ocean (LMO) hypothesis, by which the plagioclase-rich lunar highlands were formed as a flotation crust during differentiation of a global-scale magma ocean. The separation of plagioclase from the mafic cumulates is thought to be the source of the Eu depletion, as Eu is very compatible in plagioclase. Lunar basalts and volcanic glasses are commonly depleted in light REEs (LREE), and more enriched in heavy REEs (HREE). However, there is very little experimental data available on REE partitioning between lunar minerals and melts. In order to interpret the source of these distinctive REE patterns, and to model lunar petrogenetic processes, REE partition coefficients (D) between lunar minerals and melts are needed at conditions relevant to lunar processes. New data on D(sub REE) for plagioclase, and pyroxenes are now available, but there is limited available data for olivine/melt D(sub REE), particularly at pressures higher than 1 bar, and in Fe-rich and reduced compositions - all conditions relevant to the lunar mantle. Based on terrestrial data, REE are highly incompatible in olivine (i.e. D much less than 1), however olivine is the predominant mineral in the lunar interior, so it is important to understand whether it is capable of storing even small amounts of REE, and how the REEs might be fractionatied, in order to understand the trace element budget of the lunar interior. This abstract presents results from high-pressure and temperature experiments investigating REE partitioning between olivine and melt in a composition relevant to lunar magmatism.

McIntosh, E. C.↗
DOE OSTI2020

Intense Pulse Light Annealing of Perovskite Photovoltaics Using Gradient Flashes

Perovskite solar cells (PSCs) have been fabricated through high-speed and low-cost depositions but often require long annealing. Intense pulse light (IPL) can anneal thin films in seconds after deposition by inducing very high temperatures lasting for milliseconds, and multiple flashes can be used to tune the temperature profile. In this study, a gradient flash annealing (GFA) approach is introduced and compared to uniform flash annealing (UFA) by investigating the crystallinity, morphology, and phase evolution of the CH 3 NH 3 PbI 3 perovskite films and their impact on PSC performance. Unlike UFA, low-intensity pulsed irradiation during the pre-annealing stage of GFA played a significant role on enhancing the PSC performance by forming pure-phase CH 3 NH 3 PbI 3 perovskite thin films with superior morphology and high crystallinity. To understand the kinetics, a transient thermal simulation using ANSYS was developed and confirmed with an experimental setup. The results combined with microscopy and spectrophotometry were used to visualize how duration, delay time, photon flux, and flash count parameters participated in crystallization, phase, and morphology evolution. The IPL annealing induced rapid surface temperature increase, reaching as high as 800 °C, while produced well-developed and bound perovskite grains without any surface defects in an uncontrolled ambient environment with high humidity (>60%). The study resulted in PSCs with maximum efficiency and fill factor of 9.27 and 69.92% for the UFA and 11.75 and 68% when annealed through the GFA approach, respectively. Lastly, this work utilized IPL as the sole thermal source for post-deposition annealing to rapidly fabricate efficient PSCs in only 10 s, which opens the pathway for high-speed, low-cost, and large-scale automated fabrication of perovskite photovoltaics and semiconductors.

14 SOLAR ENERGY↗
NASA NTRS2014

Experimental Investigations of the Physical and Optical Properties of Individual Micron/Submicron-Size Dust Grains in Astrophysical Environments

Dust grains constitute a significant component of matter in the universe, and play an important and crucial role in the formation and evolution of the stellar/planetary systems in interstellar dust clouds. Knowledge of physical and optical properties of dust grains is required for understanding of a variety of processes in astrophysical and planetary environments. The currently available and generally employed data on the properties of dust grains is based on bulk materials, with analytical models employed to deduce the corresponding values for individual small micron/submicron-size dust grains. However, it has been well-recognized over a long period, that the properties of individual smallsize dust grains may be very different from those deduced from bulk materials. This has been validated by a series of experimental investigations carried out over the last few years, on a laboratory facility based on an Electrodynamic Balance at NASA, which permits levitation of single small-size dust grains of desired composition and size, in vacuum, in simulated space environments. In this paper, we present a brief review of the results of a series of selected investigations carried out on the analogs of interstellar and planetary dust grains, as well as dust grains obtained by Apollo-l1-17 lunar missions. The selected investigations, with analytical results and discussions, include: (a) Direct measurements of radiation on individual dust grains (b) Rotation and alignments of dust grains by radiative torque (c) Charging properties of dust grains by: (i) UV Photo-electric emissions (ii) Electron Impact. The results from these experiments are examined in the light of the current theories of the processes involved.

Abbas, M. M.↗
DOE OSTI2022

Sample Preparation and Experimental Design for In Situ Multi-Beam Transmission Electron Microscopy Irradiation Experiments

We discuss the need to understand materials exposed to overlapping extreme environments such as high temperature, radiation, or mechanical stress. When these stressors are combined there may be synergistic effects that enable unique microstructural evolution mechanisms to activate. Understanding of these mechanisms is necessary for the input and refinement of predictive models and critical for engineering of next generation materials. The basic physics and underlying mechanisms require advanced tools to be investigated. The in situ ion irradiation transmission electron microscope (I 3 TEM) is designed to explore these principles. To quantitatively probe the complex dynamic interactions in materials, careful preparation of samples and consideration of experimental design is required. Particular handling or preparation of samples can easily introduce damage or features that obfuscate the measurements. There is no one correct way to prepare a sample; however, many mistakes can be made. The most common errors and things to consider are highlighted within. The I 3 TEM has many adjustable variables and a large potential experimental space, therefore it is best to design experiments with a specific scientific question or questions in mind. Experiments have been performed on large number of sample geometries, material classes, and with many irradiation conditions. The following are a subset of examples that demonstrate unique in situ capabilities utilizing the I 3 TEM. Au nanoparticles prepared by drop casting have been used to investigate the effects of single ion strikes. Au thin films have been used in studies on the effects of multibeam irradiation on microstructure evolution. Zr films have been exposed to irradiation and mechanical tension to examine creep. Ag nanopillars were subjected to simultaneous high temperature, mechanical compression, and ion irradiation to study irradiation induced creep as well. These results impact fields including: structural materials, nuclear energy, energy storage, catalysis, and microelectronics in space environments.

47 OTHER INSTRUMENTATION↗
DOE OSTI2019

In-Situ Grain Resolved Stress Characterization During Damage Initiation in Cu-10%W Alloy

The evolution of stress during damage initiation and accumulation in a two-phase alloy consisting of a ductile copper (Cu) matrix with a randomly dispersed brittle tungsten (W) phase was studied using multiple non-destructive experimental probes. Neutron diffraction measurements were performed to examine the macroscopic strain partitioning between the two phases during a uniaxial tension test. The same material was then examined with high-energy x-ray diffraction microscopy (HEDM) and micro-computed tomography (μ-CT) measurements to monitor micromechanical field evolution. The neutron diffraction data indicated a redistribution of load between the Cu and W phases as deformation proceeds. Therefore, using HEDM to monitor individual grain micromechanical behavior, an increase followed by decrease in hydrostatic stress and a similar stress triaxiality behavior were found to occur in a subset of W grains. These same W grains were found to be in close proximity to voids observed via tomography at later stages of deformation. From these observations, we conclude that high stress triaxiality development in the W particles leads to decohesion of the interface between the Cu and W phases. The debonded regions eventually grew and coalesced with neighboring voids leading to material failure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Engineering grain boundary anisotropy to elucidate grain growth behavior in alumina

Current grain growth models have evolved to account for the relationship between grain boundary energy/mobility anisotropy and the five degrees of grain boundary character. However, the role of grain boundary networks on overall growth kinetics remains poorly understood. To experimentally investigate this problem, a highly textured Al 2 O 3 was fabricated by colloidal casting in a strong magnetic field to engineer a unique spatial distribution of grain boundary character. Microstructural evolution was quantified and compared to an untextured sample. From this comparison, a prevalence of (0001)/(0001) terminated grain boundaries with anisotropic networks were identified in the textured sample. These boundaries and their networks were found to be driving grain growth at a faster rate than predicted by models. These findings will allow better modelling of grain growth in real systems by experimentally exploring the impact thereon of grain boundary plane anisotropy and relative energy/mobility differences between neighboring boundaries.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure Evolution and Mechanical Property of Low-Alloy Steel Used for Armor Layer of Flexible Pipe During Thermomechanical Process and Hot Rolling Process

In this paper, the thermomechanical process and hot rolling process were carried out to study the microstructure evolution and mechanical property of low-alloy steel used for armor layer of flexible pipes by analyzing continuous cooling transformation curve, microstructure morphology, grain characteristics, and strength. The experimental results indicate that deformation process promotes phase transformation process of both ferrite and bainite and induces the formation of fine grain. The density of low-angle grain boundary rises with increasing cooling rate. The dislocation concentration in grain becomes larger with the extended cooling rate. The microstructure of hot-rolled specimen consists of polygonal ferrite and granular bainite, which is consistent with one of the deformed specimens with similar cooling rate in dilatometer. The microstructure evolution provides effective data fundament for hot rolling process.

36 MATERIALS SCIENCE↗
NASA NTRS2005

Comparative Planetary Mineralogy: Co, Ni Systematics in Chromite from Planetary Basalts

Spinel is a minor but important phase in planetary basalts because its variable composition often reflects basalt petrogenesis. For example, complicated zoning trends in spinel can give clues to melt evolution [1], and V concentrations in chromite lend insight into magma oxygen fugacity (fO2) conditions [2]. Nickel and Co are two elements that are commonly used as a measure of melt fractionation, and their partitioning between olivine and melt is fairly well understood. Less clear is their partitioning into spinel, although [3] has explored Ni and Co systematics in experimental charges. This study documents Ni and Co behavior in early crystallizing spinel (chromite) from several planetary basalts in an attempt to compare our results with [3], and also gain insight into basalt evolution on the three planets.

Karner, J. M.↗
DOE OSTI2018

Effect of Deformation Temperature on Dynamic Recrystallization and CSL Grain Boundary Distribution of Fe-36%Ni Invar Alloy

This paper investigated the effect of deformation temperatures on microstructure evolution and grain boundary character distribution (GBCD) of Fe-36%Ni Invar alloy during hot compression tests. The isothermal hot deformation tests were carried out in a temperature range of 850-1100 °C and a strain rate of 0.01 s{sup −1}. The grain boundary character distribution was based on the Σ3{sup n} (n = 1, 2, 3,…) coincidence site lattice (CSL) boundaries. The experimental results show that the extent of dynamic recrystallization significantly expanded at the strain rate of 0.01 s{sup −1} with the increase in temperature and this phenomenon was consistent with the evolution tendency of Σ3{sup n} boundaries. To some degree, the increasing proportion of typical low-ΣCSL boundaries, especially the increasing trend of Σ3, positively promoted the wider process of dynamic recrystallization.

36 MATERIALS SCIENCE↗
NASA NTRS2001

Carbon Nanostructure: Its Evolution During its Impact Upon Soot Growth and Oxidation

The proposed work is a ground-based study to define and quantify soot nanostructural changes in response to growth conditions, thermal and oxidative treatments and to quantify their impact upon further oxidation and growth of highly ordered carbon materials. Experimental data relating soot oxidation rates to multiple oxidizing species concentrations will directly test for additive or synergistic soot oxidation rates. Such validation is central for assessing the applicability of individual soot oxidation rates and designing oxidative strategies for controlling soot loadings in and emissions from turbulent combustion processes. Through these experiments, new insights into soot nanostructure evolution during and its impact upon oxidation by O2 and OH will be realized. It is expected that the results of this effort will spawn new research directions in future microgravity and 1g environments. Issues raised by positive or even negative demonstration of the hypotheses of this proposal have direct bearing on modelling and controlling soot formation and its destruction in nearly every combustion process producing soot.

Source record↗
DOE OSTI2025

Time correlations from steady-state expectation values

Recovering properties of correlation functions is typically challenging. On one hand, experimentally, it requires measurements with a temporal resolution finer than the system's dynamics. On the other hand, analytical or numerical analysis requires solving the system evolution. Here, we use recent results of quantum metrology with continuous measurements to derive general lower bounds on the relaxation and second-order correlation times that are both easy to calculate and measure. These bounds are based solely on steady-state expectation values and their derivatives with respect to a control parameter, and can be readily extended to the autocorrelation of arbitrary observables. We validate our method on two examples of critical quantum systems: a critical driven-dissipative resonator, where the bound matches analytical results for the dynamics, and the infinite-range Ising model, where only the steady state is solvable and thus the bound provides information beyond the reach of existing analytical approaches. Our results can be applied to experimentally characterize ultrafast systems, and to theoretically analyze many-body models with dynamics that are analytically or numerically hard.

Górecki, Wojciech [INFN, Pavia]↗
DOE OSTI2025

Time correlations from steady-state expectation values

Recovering properties of correlation functions is typically challenging. On one hand, experimentally, it requires measurements with a temporal resolution finer than the system's dynamics. On the other hand, analytical or numerical analysis requires solving the system evolution. Here, we use recent results of quantum metrology with continuous measurements to derive general lower bounds on the relaxation and second-order correlation times that are both easy to calculate and measure. These bounds are based solely on steady-state expectation values and their derivatives with respect to a control parameter, and can be readily extended to the autocorrelation of arbitrary observables. We validate our method on two examples of critical quantum systems: a critical driven-dissipative resonator, where the bound matches analytical results for the dynamics, and the infinite-range Ising model, where only the steady state is solvable and thus the bound provides information beyond the reach of existing analytical approaches. Our results can be applied to experimentally characterize ultrafast systems, and to theoretically analyze many-body models with dynamics that are analytically or numerically hard.

Górecki, Wojciech [INFN, Pavia]↗
DOE OSTI2025

A Route to Design Novel Functional Peptides by Applying a Denoising Diffusional Model to mRNA Display Libraries

In vitro directed evolution techniques, such as mRNA display, enable peptide ligand discovery and optimization. However, physical libraries that rely on a genetic code can only search a small fraction of sequence space due to inherent biases in the genetic code and experimental limitations. To address this challenge, denoising diffusion implicit models (DDIMs) are applied to generate novel peptide ligands against B‐cell lymphoma extra‐large (Bcl‐x L ), a key cancer target. Starting with high‐throughput sequencing data from previous selections, a DDIM is trained to produce novel sequences with high affinity binding. Experimental validation confirms that most generated sequences are functionally equivalent to the original library members for Bcl‐x L binding and demonstrated comparable binding kinetics and affinity relative to the wildtype and nearest original neighbors. Importantly, this approach generated rare sequences not easily accessible via mutation and directed evolution. These results indicate that DDIMs can complement and expand directed evolution data, efficiently exploring underrepresented regions of sequence space. This approach provides a broadly applicable framework for accelerating ligand discovery and optimizing molecular properties across diverse targets.

Qi, Pearl [Mork Family Department of Chemical Engi↗
NASA NTRS1985

Clustered impacts - Experiments and implications

The characteristics of impact by clusters of projectiles are experimentally studied by launching grouped projectiles of aluminum shot, steel shot, iron filings, and sand. Cratering efficiency is considered as a function of a dimensionless parameter related to projectile size and impact velocity. The effects of different target and projectile densities on cratering efficiency are examined. Crater morphology is addressed by considering a typical example, reviewing the systematics between cluster dispersion and crater morphology for vertical impacts, and examining oblique angle impacts which have relevance for planetary secondary cratering processes. These results are compared with impacts by single bodies with different strengths. The evolution of the ejecta plume for clustered impacts is compared to that for single-body impacts for vertical and oblique impacts from 1.3 to 1.8 km/s. The experimental results are discussed in the context of planetary surface processes, emphasizing processes in an atmosphere-free environment and secondary impact cratering.

Schultz, P. H.↗