Search NASA⌕ Search

SEARCH · Search NASA

Results for “Failures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

Investigation of TC-1 flight failure using power spectral analysis

During the Titan Centaur 1 test flight a failure involving at least one of the Centaur propellant boost pumps occurred. Also, neither of the boost pump speed instruments indicated pump rotation. Accelerometer data from the Titan Centaur 1 flight failure were analyzed using power spectral density methods to determine boost pump speed during attempted starts of the Centaur. The technique was demonstrated on a reference flight. The hydrogen boost pump speed transient was determined for the TC-1 flight. Other trends are seen in the data. However, these are not believed to be the oxygen boost pump. Discussion of data enhancement techniques is also presented.

Lorenzo, C. F.↗

Voltage stress effects on microcircuit accelerated life test failure rates

The applicability of Arrhenius and Eyring reaction rate models for describing microcircuit aging characteristics as a function of junction temperature and applied voltage was evaluated. The results of a matrix of accelerated life tests with a single metal oxide semiconductor microcircuit operated at six different combinations of temperature and voltage were used to evaluate the models. A total of 450 devices from two different lots were tested at ambient temperatures between 200 C and 250 C and applied voltages between 5 Vdc and 15 Vdc. A statistical analysis of the surface related failure data resulted in bimodal failure distributions comprising two lognormal distributions; a 'freak' distribution observed early in time, and a 'main' distribution observed later in time. The Arrhenius model was shown to provide a good description of device aging as a function of temperature at a fixed voltage. The Eyring model also appeared to provide a reasonable description of main distribution device aging as a function of temperature and voltage. Circuit diagrams are shown.

Johnson, G. M.↗

Stress-strain and failure properties of graphite/epoxy laminates

The results of a series of tensile tests on graphite/epoxy laminates at rates varying from 0.002 in/min to 2 in/min are reported. The loads are applied at various angles to the fiber directions in each case. The rate dependent behavior of the stress-strain response is assessed. Evidence is presented to indicate that failure first occurs on inner piles. Also, evidence is presented to indicate that, in some cases, moduli increase with increased stress or strain level. The lamination theory is used to predict moduli and comparisons with experiment are given. Also, the lamination theory is used in conjunction with three failure theories to predict ultimate strengths with varying degrees of success.

Yeow, Y. T.↗

Rate and time dependent failure of structural adhesives

Studies on two adhesives (Metlbond 1113 and 1113-2) identified as having important applications in the bonding of composite materials are presented. A testing program to ascertain stress-strain, strain-rate, time, yield, and/or failure behavior of these materials in bulk form using uniaxial tensile constant strain-rate, creep, and relaxation tests is described. The stress-strain behavior of each material is shown to be significantly rate dependent. A rate dependent stress whitening (crazing) phenomenon occurs prior to either yield or fracture. A region of linear elasticity, a region of viscoelasticity, and the onset of yielding are identified in the stress-strain behavior. The linear elastic limit and the yield point are shown to be rate dependent and agree well with an empirical equation proposed by Ludwik. A creep to failure phenomenon is shown to exist and is correlated with a delayed yield equation proposed by Crochet. Analytical predictions based on a modified Bingham model are shown to agree well with experimental stress-strain strain-rate data. Analytical predictions based on a modified Ramberg-Osgood equation are also shown for comparison purposes.

Brinson, H. F.↗

Failure and fatigue mechanisms in composite materials

A phenomenological description of microfailure under monotonic and cyclic loading is presented, emphasizing the significance of material inhomogeneity for the analysis. Failure in unnotched unidirectional laminates is reviewed for the cases of tension, compression, shear, transverse normal, and combined loads. The failure of notched composite laminates is then studied, with particular attention paid to the effect of material heterogeneity on load concentration factors in circular holes in such laminates, and a 'materials engineering' shear-lay type model is presented. The fatigue of notched composites is discussed with the application of 'mechanistic wearout' model for determining crack propagation as a function of the number of fatigue cycles.-

Rosen, B. W.↗

Rock failure analysis by combined thermal weakening and water jet impact

The influence of preheating on the initiation of fracture in rocks subjected to the impingement of a continuous water jet is studied. Preheating the rock is assumed to degrade its mechanical properties and strength in accordance with existing experimental data. The water jet is assumed to place a quasi-static loading on the surface of the rock. The loading is approximated by elementary functions which permit analytic computation of the induced stresses in a rock half-space. The resulting stresses are subsequently coupled with the Griffith criteria for tensile failure to estimate the change, due to heating, in the critical stagnation pressure and velocity of the water jet required to cause failure in the rock.

Nayfeh, A. H.↗

Test particle propagation in magnetostatic turbulence. 1. Failure of the diffusion approximation

The equation which governs the quasi-linear approximation to the ensemble and gyro-phase averaged one-body probability distribution function is constructed from first principles. This derived equation is subjected to a thorough investigation in order to calculate the possible limitations of the quasi-linear approximation. It is shown that the reduction of this equation to a standard diffusion equation in the Markovian limit can be accomplished through the application of the adiabatic approximation. A numerical solution of the standard diffusion equation in the Markovian limit is obtained for the narrow parallel beam injection. Comparison of the diabatic and adiabatic results explicitly demonstrates the failure of the Markovian description of the probability distribution function. Through the use of a linear time-scale extension the failure of the adiabatic approximation, which leads to the Markovian limit, is shown to be due to mixing of the relaxation and interaction time scales in the presence of the strong mean field.

Klimas, A. J.↗

Failure detection and control-system reconfiguration: Past, present, and future

The history of failure detection and redundancy management in aircraft applications is reviewed. To date, techniques related to that subject have been based mainly on hardware duplication of like components with failure monitoring and switchover or averaging for redundancy management. Specific examples of these techniques are discussed as they have been applied to the NASA F-8 Digital Fly-by-Wire aircraft and are to be applied to the space shuttle vehicle in the near future.

Montgomery, R. C.↗

A survey of design methods for failure detection in dynamic systems

A number of methods for detecting abrupt changes (such as failures) in stochastic dynamical systems are surveyed. The class of linear systems is concentrated on but the basic concepts, if not the detailed analyses, carry over to other classes of systems. The methods surveyed range from the design of specific failure-sensitive filters, to the use of statistical tests on filter innovations, to the development of jump process formulations. Tradeoffs in complexity versus performance are discussed.

Willsky, A. S.↗

Failure rate analysis of Goddard Space Flight Center spacecraft performance during orbital life

The reported study presents the results of analyses conducted with the aid of both Duane and Weibull growth models. The failure rate values provided may be useful for estimating future space performance, and comparing past, present, and future space performance. Failure rate data from thermal-vacuum system tests are examined and related to the space values. Attention is given to the data base, the time distribution of space malfunctions, limitations on data, and average component reliability for three years in space.

Norris, H. P.↗

Migratory gold resistive shorts - Chemical aspects of a failure mechanism

Integrated-circuit devices using the Ti/W/Au metal system are subject to failure mechanisms based on electrolytic corrosion. The migratory gold resistive short (MGRS) failure mode is one example of this mechanism and results in the formation of filamentary or dendritic deposits of gold between adjacent stripes on the IC chip. This reaction requires the presence of a sufficient amount of water, a bias voltage between adjacent stripes, and the activation of the cathodic (-) stripe. Gold ions are transported from anode to cathode through a film of moisture adsorbed on the surface of the chip; halide ions are probably involved in the transfer. Their presence is verified experimentally by X-ray photoelectron spectroscopy. Some of the chemical and electrostatic factors involved in the MGRS mechanism are discussed in this paper, including the questions of a threshold level of moisture and contamination.

Grunthaner, F. J.↗

A Closed Network Queue Model of Underground Coal Mining Production, Failure, and Repair

Underground coal mining system production, failures, and repair cycles were mathematically modeled as a closed network of two queues in series. The model was designed to better understand the technological constraints on availability of current underground mining systems, and to develop guidelines for estimating the availability of advanced mining systems and their associated needs for spares as well as production and maintenance personnel. It was found that: mine performance is theoretically limited by the maintainability ratio, significant gains in availability appear possible by means of small improvements in the time between failures the number of crews and sections should be properly balanced for any given maintainability ratio, and main haulage systems closest to the mine mouth require the most attention to reliability.

Lohman, G. M.↗

Lubrication and failure mechanisms of molybdenum disulfide films. 1: Effect of atmosphere

Friction, wear, and wear lives of rubbed molybdenum disulfide (MoS2 films applied to sanded 440C HT steel surfaces were evaluated in moist air, dry air, and dry argon. Optical microscope observations were made as a function of sliding distance to determine the effect of moisture and oxygen on the lubricating and failure mechanisms of MoS2 films. In general, the lubrication process consisted of the formation of a thin, metallic colored, coalesced film of MoS2 that flowed between the surfaces in relative motion. In air, failure was due to the transformation of the metallic colored, coalesced films to a black, powdery material. Water in the air appeared to accelerate the transformation rate. In argon, no transformation of MoS2 was observed with the microscope, but cracking and spalling of the coalesced film occurred and resulted in the gradual depletion of the film.

Fusaro, R. L.↗

The effects of participatory mode and task workload on the detection of dynamic system failures

The ability of operators to detect step changes in the dynamics of control systems is investigated as a joint function of, (1) participatory mode: whether subjects are actively controlling those dynamics or are monitoring an autopilot controlling them, and (2) concurrent task workload. A theoretical analysis of detection in the two modes identifies factors that will favor detection in either mode. Three subjects detected system failures in either an autopilot or manual controlling mode, under single-task conditions and concurrently with a subcritical tracking task. Latency and accuracy of detection were assessed and related through a speed accuracy tradeoff representation. It was concluded that failure detection performance was better during manual control than during autopilot control, and that the extent of this superiority was enhanced as dual-task load increased. Ensemble averaging and multiple regression techniques were then employed to investigate the cues utilized by the subjects in making their detection decisions.

Wickens, C. D.↗

Operational loopwheel suspension systems for Mars Rover demonstration model: Loopwheel failure report

The results are presented from the analysis of a failure which occurred in the fiberglass loop of one of the Loopwheel traction elements delivered to the Jet Propulsion Laboratory (JPL) for use on the JPL Mars Rover demonstration model. The loop failed in compression in the outer fibers forming a hinge which, through cycling, caused the inner fibers to break. The probable cause of this failure was the load being introduced as point loads at the center of the loop causing high compressive stresses and early buckling. To decrease the stress level and delay buckling, the tread lugs can be reshaped so that the entire lug contacts the ground when the loop is loaded. This can be accomplished through removal of lug material, starting with zero removal at the outer edge and linearly increasing to one-half of the lug thickness at the center.

West, E. J. M.↗

Surveys for sensitivity to fibers and potential impacts from fiber induced failures

The surveys for sensitivities to fibers and potential impacts from fiber induced failures begins with a review of the survey work completed to date and then describes an impact study involving four industrial installations located in Virginia. The observations and results from both the surveys and the study provide guidelines for future efforts. The survey work was done with three broad objectives: (1) identify the pieces of potentially vulnerable equipment as candidates for test; (2) support the transfer function work by gaining an understanding of how fibers could get into a building; and (3) support the economic analysis by understanding what would happen if fibers precipitated a failure in an item of equipment.

Butterfield, A. J.↗

Scanning microscopy in microcircuit failure analysis

A three-phase microcircuit failure analysis procedure is presented. In the first phase, the device is nondestructively tested and the data obtained is correlated with the circumstances surrounding the failure event. The device is then subjected to a limited nondestructive analysis dominated by optical and scanning electron microscopy (SEM). Knowing that microcircuits usually fail from manufacturing defects or misuse, the analyst looks for one of the probable mechanisms. The SEM has two special operating modes that provide unique data for nondestructive analysis: voltage contrast and conductive current. These are used with other SEM modes and surface analysis techniques to analyze complicated microcircuits. The last phase includes the destructive procedures. The end product of these analyses is a corrective action that will yield a highly reliable system.

Nicolas, D. P.↗

Some failure modes and analysis techniques for terrestrial solar cell modules

Analysis data are presented on failed/defective silicon solar cell modules of various types and produced by different manufacturers. The failure mode (e.g., internal short and open circuits, output power degradation, isolation resistance degradation, etc.) are discussed in detail and in many cases related to the type of technology used in the manufacture of the modules; wherever applicable, appropriate corrective actions are recommended. Consideration is also given to some failure analysis techniques that are applicable to such modules, including X-ray radiography, capacitance measurement, cell shunt resistance measurement by the shadowing technique, steady-state illumination test station for module performance illumination, laser scanning techniques, and the SEM.

Shumka, A.↗