Search NASA⌕ Search

SEARCH · Search NASA

Results for “cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

Effect of ATF Cr-coated-Zircaloy on BWR In-vessel Accident Progression during a Station Blackout

The deposition of protective coatings on nuclear fuel cladding has been considered as a near-term Accident Tolerant Fuel (ATF) concept that will reduce the high-temperature oxidation rate and enhance accident tolerance of the cladding while providing additional benefits during normal and transient. In this study, the performance of the proposed ATF concept of Cr-coated-Zircaloy is assessed using a generic Boiling Water Reactor MELCOR plant model considering a Short-term Station Blackout (STSBO) scenario. Simulation results indicate that the use of Cr-coated-Zircaloy as cladding and canister material mitigates the core degradation process as compared to the traditional Zircaloy cladding and canister design. The onset of fuel degradation and collapse is delayed by over thirty minutes, and the extent of fuel degradation is reduced. Specifically, the gross in-vessel hydrogen generation decreased by almost a factor of three. Although the eutectic reaction between Cr-coating and Zircaloy could cause an early failure of the coating, the improvement in the delay of fuel degradation is still notable. In addition, a thicker coating is found helpful to obtain additional coping time and to decrease hydrogen generation. In addition to the eutectic formation that may compromise Cr-coated Zr, a different failure mode is identified for the Cr-coated-Zr when compared to Zircaloy; i.e., a complete melt of base material leads to component collapse before the coating is oxidized and consumed. These findings can help the industry focus on productive areas of research and development for accident-tolerant fuel concepts and enhancement of core safety margins.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Initial demonstration of automated fuel performance modeling with 1977 EBR-II metallic fuel pins using BISON code with FIPD and IMIS databases

Using the BISON fuel performance code, simulations were conducted using an automated process to read initial and operating conditions from the Fuels Irradiation and Physics Database (FIPD) and Integral Fast Reactor materials information system (IMIS) database, which contains metallic fuel data from the Experimental Breeder Reactor-II (EBR-II). This work demonstrates use of an integrated framework to access the vast majority of EBR-II experimental fuel pin data to support rapid development of fuel performance models for next-generation metallic fuel systems. With this capability, validation for fuel qualification can be performed rapidly. Between IMIS and FIPD, there is enough information to conduct 1977 unique EBR-II metallic fuel pin histories from 24 different experiments, at varying levels of detail between the two databases. Each of these histories includes a high-resolution power history, flux history, coolant channel flow rates, and coolant channel temperatures. Fission gas release (FGR), cumulative damage fraction (CDF), fuel axial swelling, cladding profilometry, and burnup were all simulated in BISON. The results were compared to post-irradiation examination (PIE) results for the initial demonstration of automated BISON modeling. BISON simulations conducted with IMIS and FIPD were in rough agreement with PIE measurements and calculations. Cladding profilometry, FGR, and fuel axial swelling were found to be in rough agreement with PIE measurements, depending on the physics used within the BISON input files. Here, the mechanical contact solver chosen was found to significantly impact axial fuel swelling and cladding strain predictions. CDF values were assessed to see whether pin failure may have been predicted (CDF ≥ 1). This work suggests that continued development of an automated tool for BISON should focus on inclusion of the Fast Flux Test Facility (FFTF) experimental data for a larger database for metallic fuel, improved physical models to better capture fuel performance, such as fuel-cladding interactions, and a more detailed comparison with available PIE data to further the BISON model development.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Design of separate-effects In-Pile transient boiling experiments at the $\mathrm{TREAT}$ Facility

The cladding-to-coolant heat transfer during rapid power excursions, such as reactivity-initiated accidents, remains a crucial area of uncertainty in nuclear reactor safety. This uncertainty impacts the ability to accurately predict fuel performance behavior for these conditions. Improving our understanding of transient cladding-to-coolant heat transfer will enhance our ability to model design basis accidents and could increase design and improve safety margins for the current commercial fleet and advanced reactors. To address these issues, the Critical Heat Flux Static Environment Rodlet Transient Test Apparatus (CHF-SERTTA) experiment uses a novel approach with a borated stainless-steel heater rodlet that can replicate cladding temperatures experienced during a design-basis reactivity-initiated accident. The rodlet and experiment is instrumented to provide temperature and thermal-hydraulic conditions throughout the transient. The design of the rodlet allows for separate effect testing that eliminates complexities with a fuel and cladding specimen. We report the experiments have provided data that will be used to improve our understanding of boiling behavior, specifically critical heat flux, under transient conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fuel performance evaluation of two high burnup PWR core designs during normal operation, control rod withdrawal, and control rod ejection scenarios

There is interest among utilities to extend the current, 18-month operating cycle to 24 months. Economically, this extension would require greater than 5 % enrichment and peak rod average discharge burnup levels above 62 GWd/MTU. A notable challenge of increasing enrichment is the resulting additional excess reactivity encountered during the early stages of fuel life. To accommodate, burnable absorbers beyond soluble boron are introduced into the fuel system. In high burnup fuels, the possibilities of cladding lift-off and fuel melting increase due, in part, to increased rod internal pressures and limited fuel thermal conductivity, respectively. This work collaboratively employs PARCS, RELAP5-3D, and BISON to compare the fuel performance of two high burnup fuel candidates with higher than 5 % enrichment. Here, the fuel performance parameters were compared to current NRC guidance. The results demonstrate an annular fuel design with homogenously blended gadolinium as a burnable absorber operates with greater safety margins during normal operation, allowing for additional operational flexibility. During normal operation, the core design utilizing Integral Fuel Burnable Absorber pins contained fuel pins which reached plenum pressures above 15.5 MPa by the end of the first fuel cycle and fuel pins experienced cladding hoop strains above 1 %. In the Gd core design, only two observed pins experienced plenum pressures above 15.5 MPa and no pins exceeded 1 % cladding hoop strain. During the control rod withdrawal scenario, plenum pressures for pins in both designs marginally exceeded system pressure, however neither experienced excessive hoop strain. The Gd core design experienced a maximum fuel temperature of 2418 K, which is significantly higher than the Integral Fuel Burnable Absorber design at 2157 K, but still within regulatory guidance. We predicted that the fuel in both could return to service after the CRW event. We also predicted that cladding would not fail during the Control Rod Ejection in either core design. Generally, the Integral Fuel Burnable Absorber core design performed with greater safety margin with regards to temperature during normal operation and the transient events. However, the Gd core design performed with greater safety margin regarding plenum pressure and hoop strain limits during normal operation and both transient events.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Experimental investigations of Critical Heat Flux re-occurrence on post-CHF surfaces

Under the extreme environments of light water reactors, the cladding materials demonstrate evolutionary transformations in terms of material compositions, surface morphologies, and thermal-physical properties. This study investigates how the temperature overshooting of Critical Heat Flux (CHF) affects the re-occurrence of CHF on the post-CHF surfaces. Experimental results reveal that the CHF difference between as-received and post-CHF surfaces can be significant, which depends on materials. CHF is enhanced on post-CHF Stainless Steel (SS 316) specimens while it deteriorates on post-CHF Inconel-600 specimens. In comparison with the as-received surfaces, the post-CHF surface of SS 316 is more hydrophobic, while Inconel 600 is more hydrophilic. The scanning electron microscope micrographs of post-CHF surfaces show that surface morphologies that are structured by oxide crystals are formed on SS 316 samples but not on Inconel 600 samples. The physical rationale behind the CHF difference could be boiling heat transfer conjugated with thermal-physical proprieties of investigated surface materials and surface morphologies features. In conclusion, the results imply that it is indispensable to bookkeep the evolutionary changes of cladding surface materials, especially for cladding candidates of Accident Tolerant Fuel since operation histories can leave footprints on cladding surfaces, thus resulting in CHF re-occurrence differences.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Magnetic collimation of fast electrons in specially engineered targets irradiated by ultraintense laser pulses

The efficient magnetic collimation of fast electron flow transporting in overdense plasmas is investigated with two-dimensional collisional particle-in-cell numerical simulations. It is found that the specially engineered targets exhibiting either high-resistivity-core-low-resistivity-cladding structure or low-density-core-high-density-cladding structure can collimate fast electrons. Two main mechanisms to generate collimating magnetic fields are found. In high-resistivity-core-low-resistivity-cladding structure targets, the magnetic field at the interfaces is generated by the gradients of the resistivity and fast electron current, while in low-density-core-high-density-cladding structure targets, the magnetic field is generated by the rapid changing of the flow velocity of the background electrons in transverse direction (perpendicular to the flow velocity) caused by the density jump. The dependences of the maximal magnetic field on the incident laser intensity and plasma density, which are studied by numerical simulations, are supported by our analytical calculations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Chirped laser dispersion spectroscopy using a directly modulated quantum cascade laser

Chirped laser dispersion spectroscopy (CLaDS) utilizing direct modulation of a quantum cascade laser (QCL) is presented. By controlling the laser bias nearly single- and dual-sideband CLaDS operation can be realized in an extremely simplified optical setup with no external optical modulators. Capability of direct single-sideband modulation is a unique feature of QCLs that exhibit a low linewidth enhancement factor. The developed analytical model shows excellent agreement with the experimental, directly modulated CLaDS spectra. This method overcomes major technical limitations of mid-infrared CLaDS systems by allowing significantly higher modulation frequencies and eliminating optical fringes introduced by external modulators.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Dynamic PRA-Based Estimation of PWR Coping Time Using a Surrogate Model for Accident Tolerant Fuel

In this study, we propose an interpolation-based response surface surrogate methodology to manage a large number of scenarios in dynamic probabilistic risk assessment. It adopts the shape Dynamic Time Warping algorithm to cluster the interpolation neighborhood from time series sample data. The interpolation method was adapted from Taylor Kriging to allow a reduced-order model of the Taylor series. In order to demonstrate its applicability to complex issues in risk assessment for nuclear engineering, an example risk response surface to estimate emergency core cooling system (ECCS) criteria for triplex silicon carbide (SiC) accident-tolerant fuel was constructed. The response surface was exploited to estimate the cumulative failure probability of the fuel cladding structure due to the uncertainties in operator actions and safety systems. The functional failures were assessed based on a combination of individual layer failures computed by coupling Risk Analysis Virtual Environment software with a pressurized water reactor 1000-MW(electric) RELAP5 model and the in-house fuel performance assessment module. Results showed that SiC cladding failure probability spiked less than 1 min after a large-break loss-of- coolant accident whenever the current ECCS criteria for Zircaloy-4 (Zr-4) cladding was used. However, it still provides an increased safety margin of three orders of magnitude compared to Zr-4. This positive margin could be utilized to relax active ECCS requirements by allowing deviations of up to 450 s in its actuation time. The proposed surrogate methodology generated a response surface of SiC cladding failure probability reasonably well, with a significant savings of computation time. This methodology is expected to be useful in the analysis of system response with complex uncertainty sources.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Modal reduction in single crystal sapphire optical fiber

A new type of single crystal sapphire optical fiber (SCSF) design is proposed to reduce the number of guided modes via a highly dispersive cladding with a periodic array of high and low index regions in the azimuthal direction. The structure retains a “core” region of pure single crystal (SC) sapphire in the center of the fiber and a “cladding” region of alternating layers of air and SC sapphire in the azimuthal direction that is uniform in the radial direction. The modal characteristics and confinement losses of the fundamental mode were analyzed via the finite element method by varying the effective core diameter and the dimensions of the “windmill” shaped cladding. The simulation results showed that the number of guided modes were significantly reduced in the “windmill” fiber design, as the radial dimension of the air and SC sapphire cladding regions increase with corresponding decrease in the azimuthal dimension. It is anticipated that the “windmill” SCSF will readily improve the performance of current fiber optic sensors in the harsh environment and potentially enable those that were limited by the extremely large modal volume of unclad SCSF.

36 MATERIALS SCIENCE↗

Steady-State Thermal-Hydraulic Analysis of the LEU-Fueled Dalat Nuclear Research Reactor

This paper presents results of steady-state thermal-hydraulic analysis for the designed working core of the Dalat Nuclear Research Reactor (DNRR) using the PLTEMP/ANL code. The core was designed to be loaded with 92 low-enriched uranium (LEU) VVR-M2 fuel bundles (FBs) and 12 beryllium rods surrounding a neutron trap at the core center, for replacement of the previous core with 104 high-enriched uranium (HEU) VVR-M2 FBs. Before using this code for thermohydraulic analysis of the designed LEU working core, it was validated by comparing calculation results with experimental data collected from the HEU working core of the DNRR. The discrepancy between calculated results and measured data was at the maximum about 0.8°C and 1.5°C of fuel cladding and outlet coolant temperatures, respectively. In the design calculation, thermohydraulic safety was confirmed through evaluation of the fuel cladding and coolant temperatures, as well as of other safety parameters such as Departure from Nucleate Boiling Ratio (DNBR) and Onset of Nucleate Boiling Ratio (ONBR). The calculation results showed that, in normal operation conditions at full nominal thermal power of 500 kW without uncertainty parameters, the maximum fuel cladding temperature of the hottest FB was about 90.4°C, which is lower than its limit value of 103°C, the minimum DNBR was 32.0, which is much higher than the recommended value of 1.5, and the minimum ONBR was 1.43, which is higher than the recommended value of 1.4 for VVR-M2 LEU fuel type. When the global and local hot channel factors were taken into account, the maximum temperature of fuel cladding at the hottest FB was about 98.4 °C, for global only, and 114.3°C, for global together with local hot channel factors. The calculation results confirm the safety operation of the designed LEU core loaded with 92 fresh VVR-M2 FBs.

Nguyen, Kien-Cuong↗

The Mechanical Response of High Burnup 17x17 PWR Fuel Rods Under Bending

As a part of the US Department of Energy Office of Nuclear Energy High Burnup Spent Fuel Data Project, Oak Ridge National Laboratory has performed 4pt-bend tests on a series of 17x17 PWR fuel rods that were discharged with rod average burnups between 50 and 60 GWd/MTU. The rods include four different kinds of fuel cladding: standard Zircaloy-4 (Zirc-4), low-tin (LT) Zirc-4, ZIRLO, and M5. Six rods of each type (combining Zirc-4 and LT Zirc-4 as one type) were tested to failure at room temperature and 200 oC. Three of each type experienced a full-length heat treatment cycle from RT to 400 oC to RT with an 8 hr soak at 400 oC to simulate the expected limiting vacuum drying condition, which potentially induces hydride reorientation and causes some annealing of irradiation damage in the cladding. Overall, the fuel rods show significant capacity to deflect in bending and exhibit non-linear deformation before failing. The calculated failure strains range from 1.5% to 3.8%. The simulated vacuum drying heat treatment had the largest effect on fuel rods with ZIRLO and M5 cladding. In both cases the heat treatment caused increases in the plastic strain at failure, suggesting some annealing of irradiation damage is occurring. The finite element modeling of the 4pt bending test assume the pellet is a collection of pellet wedge pieces. The results for the Zircaloy-4 rods suggest that the pellets are bonded to the cladding and friction controls the relative motion of the pellet wedge pieces.

Cantonwine, Paul↗

Scalable waveguide design for three-level operation in Neodymium doped fiber laser

We have constructed a double clad neodymium doped fiber laser operating on the three-level 4 F 3/2 → 4 I 9/2 transition. The laser has produced 11.5 W at 925 nm with 55% slope efficiency when pumped at 808 nm, comparable to the best previous results for a double-clad fiber configuration on this transition. Higher power pumping with both 808 nm and 880 nm sources resulted in an output of 27 W, albeit at lower slope efficiency. In both cases, output power was limited by available pump, indicating the potential for further power scaling. To suppress the stronger four-level 4 F 3/2 → 4 I 11/2 transition we developed a waveguide that provides spectral filtering distributed along the length of the fiber, based on an all-solid micro-structured optical fiber design, with resonant inclusions creating a leakage path to the cladding. Furthermore, the waveguide supports large mode areas and provides strong suppression at selectable wavelength bands, thus easing the restrictions on core and cladding sizes that limited power scaling of previous approaches.

42 ENGINEERING↗

High-temperature stable FBGs fabricated by a point-by-point femtosecond laser inscription for multi-parameter sensing

A high-temperature resistant fiber Bragg grating (FBG) with pronounced cladding modes is fabricated using a simple, fast, and flexible point-by-point femtosecond laser inscription. Cladding modes of different orders exhibit various sensitivities to changes in refractive index of the surrounding medium and temperature, while the Bragg wavelength is only dependent on the ambient temperature. By combining the resonance of cladding modes and the Bragg resonance, measurement of variations of temperature and surrounding refractive index can be achieved. Survivability of the cladding modes and the core mode in the fabricated FBG at elevated temperatures up to 1000°C is demonstrated.

Zhu, Chen (ORCID:0000000232567330)↗

Microbeam X-Ray Absorption Near-Edge Spectroscopy of Alloying Elements in the Oxide Layers of Irradiated Zircaloy-2

Hydrogen pickup of zirconium-based fuel cladding and structural materials during in-reactor corrosion can degrade fuel components because the ingress of hydrogen can lead to the formation of brittle hydrides. In the boiling water reactor (BWR) environment, Zircaloy-2 fuel cladding and structural components such as water rods and channels can experience accelerated hydrogen pickup, whereas Zircaloy-4 components exposed to similar conditions do not. Because the principal difference between the two alloys is that Zircaloy-2 contains nickel, accelerated hydrogen pickup has been hypothesized to result from the presence of nickel. However, an understanding of the mechanism by which this acceleration occurs is still lacking. We investigated the link between hydrogen pickup and the oxidation behavior of alloying elements when incorporated into the oxide layers formed on zirconium alloys when corroded in the reactor. Synchrotron radiation microbeam X-ray absorption near-edge spectroscopy (XANES) at the Advanced Photon Source was performed on carefully selected BWR-corroded Zircaloy-2 water rods at an assembly-averaged burnup ranging from 32.8 to 74.6 GWd/MTU to determine the oxidation states of alloying elements, such as iron and nickel, within the oxide layers as a function of distance from the oxide-metal interface at high burnup. Samples were chosen for comparison based on having similar oxide thicknesses, processing, elevation, reactors, and fluences but different hydrogen pickup fractions. Examinations of the oxide layers formed on these samples showed that (1) the oxidation states of these alloying elements changed with distance from the oxide-metal interface, (2) these elements exhibited delayed oxidation relative to the host zirconium, and (3) nickel in Zircaloy-2 remained metallic in the oxide layer at a longer distance from the oxide-metal interface than iron. An analysis of these results showed an apparent correlation between the delayed oxidation of nickel and higher hydrogen pickup of Zircaloy-2 at high burnup.

alloying elements↗

Estimation of steady-state and transcient power distributions for the RELAP analyses of the 1963 loss-of-flow and loss-of-pressure tests at BR2.

To support the safety analyses required for the conversion of the Belgian Reactor 2 (BR2) from highly-enriched uranium (HEU) to low-enriched uranium (LEU) fuel, the simulation of a number of loss-of-flow tests, with or without loss of pressure, has been undertaken. These tests were performed at BR2 in 1963 and used instrumented fuel assemblies (FAs) with thermocouples (TC) imbedded in the cladding as well as probes to measure the FAs power on the basis of their coolant temperature rise. The availability of experimental data for these tests offers an opportunity to better establish the credibility of the RELAP5-3D model and methodology used in the conversion analysis. In order to support the HEU to LEU conversion safety analyses of the BR2 reactor, RELAP simulations of a number of loss-of-flow/loss-of-pressure tests have been undertaken. Preliminary analyses showed that the conservative power distributions used historically in the BR2 RELAP model resulted in a significant overestimation of the peak cladding temperature during the transient. Therefore, it was concluded that better estimates of the steady-state and decay power distributions were needed to accurately predict the cladding temperatures measured during the tests and establish the credibility of the RELAP model and methodology. The new approach ('best estimate' methodology) uses the MCNP5, ORIGEN-2 and BERYL codes to obtain steady-state and decay power distributions for the BR2 core during the tests A/400/1, C/600/3 and F/400/1. This methodology can be easily extended to simulate any BR2 core configuration. Comparisons with measured peak cladding temperatures showed a much better agreement when power distributions obtained with the new methodology are used.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Neutron Diffraction Measurement of Residual Stresses in “OSU Plate”

Aluminum-clad U10Mo (including zirconium diffusion layer) fuel assembly plates are bound to be in a state of residual stress due to the mismatch of thermal expansion of the constituent phases. Due to the geometry of the plates, i.e. thin beams, it is expected that the stress will predominantly be in-plane. The thermal expansion of the aluminum cladding, zirconium diffusion layer and U10Mo foil are roughly α Al =22x10 -6 /K, α Zr =5x10 -6 /K, and α U10Mo =10x10 -6 /K. Note that the coefficient of thermal expansion of the zirconium is quoted as that in the a direction in the hexagonal close packed crystal structure because of the strong texture in the rolled zirconium foil, in which the a-axis are strongly preferred in the in-plane direction. During cooling from the hot isostatic pressing (HIP’ing) temperature, the zirconium contracts considerably less than the U10Mo, which in turn, contracts less than the aluminum. Because the aluminum dominates in terms of volume fraction, it is expected that the U10Mo foil and zirconium bonding layer will be in a residual stress state of in-plane compression at room temperature after bonding. This has been verified for the U10Mo foil in a mini fuel plate using x-ray diffraction at the Advanced Photon Source, but measurements of the stress state of the aluminum and zirconium were not possible at the APS. Also, the APS measurements were limited to mini size fuel plates Neutron diffraction experiments of residual stress on the “OSU plate” were completed on the Spectrometer for Materials Research at Temperature and Stress (SMARTS) at the Lujan Center at LANSCE between 2/19-21/2013. Longitudinal and transverse residual strain profiles were measured on an Al-clad U10-Mo OSU plate. Residual strains from the aluminum cladding, the zirconium bonding layer and the U10Mo fuel foil were recorded.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Anisotropic Azimuthal Power and Temperature distribution on FuelRod: Impact on Hydride Distribution

The degradation of the zirconium cladding may limit nuclear fuel performance. In the high temperature environment of a reactor, the zirconium in the cladding corrodes, releasing hydrogen in the process. Some of this hydrogen is absorbed by the cladding in a highly inhomogeneous manner. The distribution of the absorbed hydrogen is extremely sensitive to temperature and stress concentration gradients. The absorbed hydrogen tends to concentrate near lower temperatures. This hydrogen absorption and hydride formation can cause cladding failure. This project set out to improve the hydrogen distribution prediction capabilities of the BISON fuel performance code. The project was split into two primary sections, first was the use of a high fidelity multi-physics coupling to accurately predict temperature gradients as a function of r, θ , and z, and the second was to use experimental data to create an analytical hydrogen precipitation model. The Penn State version of thermal hydraulics code COBRA-TF (CTF) was successfully coupled to the DeCART neutronics code. This coupled system was verified by testing and validated by comparison to FRAPCON data. The hydrogen diffusion and precipitation experiments successfully calculated the heat of transport and precipitation rate constant values to be used within the hydrogen model in BISON. These values can only be determined experimentally. These values were successfully implemented in precipitation, diffusion and dissolution kernels that were implemented in the BISON code. The coupled output was fed into BISON models and the hydrogen and hydride distributions behaved as expected. Simulations were conducted in the radial, axial and azimuthal directions to showcase the full capabilities of the hydrogen model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of Molybdenum as a Surrogate for Iridium in the GPHS Weld Development

The welding equipment used for welding iridium containers (clads) at Los Alamos National Laboratory is twenty five years old and is undergoing an upgrade. With the upgrade, there is a requirement for requalification of the welding process, and the opportunity for process improvement. Testing of the new system and requalification will require several welds on iridium test parts and clads, and any efforts to improve the process will add to the need for iridium parts. The extreme high cost of iridium imposes a severe limitation on the extent of test welding that can be done. The 2 inch diameter, 0.027 inch thick, iridium blank disc that the clad cup is formed from, is useful for initial weld trials, but it costs $5000. The development clad sets needed for final tests and requalification cost $15,000 per set. A solution to iridium cost issue would be to do the majority of the weld development on a less expensive surrogate metal with similar weld characteristics. One such metal is molybdenum. Since its melting index (melting temperature x thermal conductivity) is closest to iridium, welds on molybdenum should be similar in size for a given weld power level. Molybdenum is inexpensive; a single 2 inch molybdenum disc costs only $9. In order to evaluate molybdenum as a surrogate for iridium, GTA welds were first developed to provide full penetration on 0.030 inch thick molybdenum discs at speeds of 20, 25, and 30 inches per minute (ipm). These weld parameters were then repeated on the standard 0.027 inch thick iridium blanks. The top surface and bottom surface (root) width and grain structure of the molybdenum and iridium welds were compared, and similarities were evident between the two metals. Due to material and thickness differences, the iridium welds were approximately 35% wider than the molybdenum welds. A reduction in iridium weld current of 35% produce welds slightly smaller than the molybdenum welds yet showed that current could be scaled according to molybdenum/iridium weld width ratio to achieve similar welds. Further weld trials using various thicknesses of molybdenum determined that 0.024 inch thick molybdenum material would best match the 0.027 inch thick iridium in achieving comparable welds when using the same welding parameters. Across the range of welding speeds, the characteristic weld pool shape and solidification grain structure in the two materials was also similar. With the similarity of welding characteristics confirmed, and the appropriate thickness of molybdenum determined, it has been concluded that the use of molybdenum discs and tube sections will greatly expand the weld testing opportunities prior to iridium weld qualification

Engineering(42)↗