A rapid lithium-ion cathode discovery pipeline and its exemplary application
A new computational screening pipeline accelerates the process of identifying potential Li-ion cathodes, with a demonstration case upon its preliminary application.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A new computational screening pipeline accelerates the process of identifying potential Li-ion cathodes, with a demonstration case upon its preliminary application.
This report is the second part of a three-part final report of research performed under an NRA cooperative Agreement contract. The first part is NASA/CR-2012-217415. The third part is NASA/CR-2012-217417. Jets have been utilized in various turbomachinery applications in order to improve gas turbines performance. Jet pulsation is a promising technique because of the reduction in the amount of air removed from compressor. In this work two areas of pulsed jets applications were computationally investigated using the commercial code Fluent (ANSYS, Inc.); the first one is film cooling of High Pressure Turbine (HPT) blades and second one is flow separation control over Low Pressure Turbine (LPT) airfoil using Vortex Generator Jets (VGJ). Using pulsed jets for film cooling purposes can help to improve the effectiveness and thus allow higher turbine inlet temperature. Effects of the film hole geometry, blowing ratio and density ratio of the jet, pulsation frequency and duty cycle of blowing on the film cooling effectiveness were investigated. As for the low-pressure turbine (LPT) stages, the boundary layer separation on the suction side of airfoils can occur due to strong adverse pressure gradients. The problem is exacerbated as airfoil loading is increased. Active flow control could provide a means for minimizing separation under conditions where it is most severe (low Reynolds number), without causing additional losses under other conditions (high Reynolds number). The effects of the jet geometry, blowing ratio, density ratio, pulsation frequency and duty cycle on the size of the separated region were examined in this work. The results from Reynolds Averaged Navier-Stokes and Large Eddy Simulation computational approaches were compared with the experimental data.
In this paper, we focus on the fourth-order biharmonic equation which also has been appeared with fractional derivative order. Then, we generalize the fractional biharmonic equation using the concept of variable-order (V-O) fractional derivative in the type of Caputo namely V-O fractional biharmonic equation (V-OFBE). To establish a method for solving V-OFBE, we firstly derive the operational matrix of V-O fractional derivatives for the shifted second kind Chebyshev polynomials. For obtaining this operational matrix with a general procedure, we implement the analytical form of these polynomials and some properties of the V-O fractional derivatives. This approach reduces the V-OFBE to a system of algebraic equations which considerably decreases the following computations. The applicability and reliability of the proposed method are investigated by solving some test problems. The experimental results show the spectral rate of convergence.
The code COSY INFINITY uses a beamline coordinate system with a Frenet–Serret frame relative to the reference particle, and calculates differential algebra-valued transfer maps by integrating the ODEs of motion in the respective vector space over a differential algebra (DA). In our work, we described and performed computation of the DA transfer map of an electrostatic spherical deflector in a laboratory coordinate system using two conventional methods: (1) by integrating the ODEs of motion using a numerical integrator and (2) by computing analytically and in closed form the properties of the respective elliptical orbits from Kepler theory. We compared the resulting transfer maps with (3) the DA transfer map of COSY INFINITY’s built-in electrostatic spherical deflector element ESP and (4) the transfer map of the electrostatic spherical deflector computed using the program GIOS, which uses analytic formulas from a paper1 by Hermann Wollnik regarding second-order aberrations. In addition to the electrostatic spherical deflector, we studied an electrostatic cylindrical deflector, where the Kepler theory is not applicable. We computed the DA transfer map by the ODE integration method (1), and we compared it with the transfer maps by (3) COSY INFINITY’s built-in electrostatic cylindrical deflector element ECL and (4) GIOS. The transfer maps of electrostatic spherical and cylindrical deflectors obtained using the direct calculation methods (1) and (2) are in excellent agreement with those computed using (3) COSY INFINITY. On the other hand, we found a significant discrepancy with (4) the program GIOS.
H\"older-Brascamp-Lieb inequalities provide upper bounds for a class of multilinear expressions, in terms of $L^p$ norms of the functions involved. They have been extensively studied for functions defined on Euclidean spaces. Bennett-Carbery-Christ-Tao have initiated the study of these inequalities for discrete Abelian groups and, in terms of suitable data, have characterized the set of all tuples of exponents for which such an inequality holds for specified data, as the convex polyhedron defined by a particular finite set of affine inequalities. In this paper we advance the theory of such inequalities for torsion-free discrete Abelian groups in three respects. The optimal constant in any such inequality is shown to equal $1$ whenever it is finite. An algorithm that computes the admissible polyhedron of exponents is developed. It is shown that nonetheless, existence of an algorithm that computes the full list of inequalities in the Bennett-Carbery-Christ-Tao description of the admissible polyhedron for all data, is equivalent to an affirmative solution of Hilbert's Tenth Problem over the rationals. That problem remains open. Applications to computer science will be explored in a forthcoming companion paper.
Here this paper presents an overview on the application of CALPHAD (CALculation of Phase Diagrams) methodology in the design and development of advanced lightweight metallic materials including magnesium, aluminum, titanium, aluminum-based metal matrix composites, and high entropy alloys. In this work, CALPHAD methodology has been established and summarized from the construction of databases describing thermodynamics, atomic mobility, kinetics, thermo-physical properties (such as viscosity) to the application of computational design of lightweight materials. The examples in this paper have demonstrated the effectiveness and capability of CALPHAD methodology in accelerating the design of advanced lightweight materials by optimizing the compositions and various heat-treatment conditions, modifying the evolution of microstructures during processing, and finally predicting the mechanical properties (e.g., yield strength and hardness) of the lightweight components. Although the examples are given in lightweight alloys for structural applications, the fundamental methodology and modeling principles are applicable to all materials and engineering applications. Thus, the future of the advanced material design will be strongly based on development of CALPHAD methodology such as the construction of reliable databases coupled with CALPHAD-based models for various applications.
Research in computer animation and simulation of human task performance requires sophisticated geometric modeling and user interface tools. The software for a research environment should present the programmer with a powerful but flexible substrate of facilities for displaying and manipulating geometric objects, yet insure that future tools have a consistent and friendly user interface. Jack is a system which provides a flexible and extensible programmer and user interface for displaying and manipulating complex geometric figures, particularly human figures in a 3D working environment. It is a basic software framework for high-performance Silicon Graphics IRIS workstations for modeling and manipulating geometric objects in a general but powerful way. It provides a consistent and user-friendly interface across various applications in computer animation and simulation of human task performance. Currently, Jack provides input and control for applications including lighting specification and image rendering, anthropometric modeling, figure positioning, inverse kinematics, dynamic simulation, and keyframe animation.
Recent years have seen significant advancements in exploring novel light-matter interactions such as hyperbolic dispersion within natural crystals. However, current studies have predominantly concentrated on local optical response of materials characterized by a dielectric tensor without spatial dispersion. Here, we investigate the nonlocal response in optically-active crystals with screw symmetries, revealing their lossless, super-dispersive properties compared to traditional optical response functions. We leverage this universal nonlocal dispersion, i.e. the dispersion of optical rotatory power, to explore a novel spectral de-multiplexing scheme compared to conventional gratings, prisms and metasurfaces. We design and demonstrate an ‘Nonlocal-Cam’ - a camera that exploits nonlocal dispersion through sampling of polarized spectral states and the application of computational spectral reconstruction algorithms. The Nonlocal-Cam captures information in both laboratory and outdoor field experiments which is unavailable to traditional intensity cameras - the spectral texture of polarization. Merging the fields of nonlocal electrodynamics and computational imaging, our work paves the way for exploiting nonlocal optics of optically active materials in a variety of applications, from biological microscopy to physics-driven machine vision and remote sensing.
The role of Ames Research Center in conducting basic aerodynamics research through computer simulations is described. The computer facilities, including supercomputers and peripheral equipment that represent the state of the art, are described. The methodology of computational fluid dynamics is explained briefly. Fundamental studies of turbulence and transition are being pursued to understand these phenomena and to develop models that can be used in the solution of the Reynolds-averaged Navier-Stokes equations. Four applications of computer simulations for aerodynamics problems are described: subsonic flow around a fuselage at high angle of attack, subsonic flow through a turbine stator-rotor stage, transonic flow around a flexible swept wing, and transonic flow around a wing-body configuration that includes an inlet and a tail.
A general method for parallel and vector numerical solutions of stochastic dynamic programming problems is described for optimal control of general nonlinear, continuous time, multibody dynamical systems, perturbed by Poisson as well as Gaussian random white noise. Possible applications include lumped flight dynamics models for uncertain environments, such as large scale and background random atmospheric fluctuations. The numerical formulation is highly suitable for a vector multiprocessor or vectorizing supercomputer, and results exhibit high processor efficiency and numerical stability. Advanced computing techniques, data structures, and hardware help alleviate Bellman's curse of dimensionality in dynamic programming computations.
The flowfield induced by a single, subsonic jet exhausting perpendicularly from a flat plate into a subsonic crossflow has been numerically investigated. The test case was chosen to match available experimental data where the jet Mach number was 0.78, and the freestream Mach number was 0.13. Time-averaged solutions were obtained using the thin-layer Navier-Stokes equations and two overlapping grids. The solutions were sensitive to the radial grid clustering near the edge of the jet and to the far-field boundary conditions. Experimental data comparisons were required to determine the most appropriate jet grid and satisfactory boundary conditions. Globally, the solutions converged in about 6000 iterations. The computational results accurately showed the deflected jet and associated contrarotating vortices. The fine clustered grid in the region upstream of the jet exit allowed the horseshoe vortex in the boundary layer near the jet exit to be captured. Most importantly for aircraft applications, the computed plate pressure distributions compared favorably with the experimental data over most of the surface. However, in the wake region immediately downstream of the jet exit, where there is extensive flow separation, some discrepancies with experimental data were observed. Two turbulence models were used in this study: (1) the zero-equation, two layer Baldwin-Lomax turbulence model; and (2) one-equation Baldwin-Barth turbulence model. The turbulence models gave results which generally compared no better with experimental data than the laminar computation results.
Mercury (Hg) is a global environmental contaminant. Major anthropogenic sources of Hg emission include gold mining and the burning of fossil fuels. Once deposited in aquatic environments, Hg can undergo redox reactions, form complexes with ligands, and adsorb onto particles. It can also be methylated by microorganisms. Mercury, especially its methylated form methylmercury, can be taken up by organisms, where it bioaccumulates and biomagnifies in the food chain, leading to detrimental effects on ecosystem and human health. In support of the recently enforced Minamata Convention on Mercury, a legally binding international convention aimed at reducing the anthropogenic emission of—and human exposure to—Hg, its global biogeochemical cycle must be understood. Thus, a detailed understanding of the molecular-level interactions of Hg is crucial.The ongoing rapid development of hardware and methods has brought computational chemistry to a point that it can usefully inform environmental science. This is particularly true for Hg, which is difficult to handle experimentally due to its ultratrace concentrations in the environment and its toxicity. The current account provides a synopsis of the application of computational chemistry to filling several major knowledge gaps in environmental Hg chemistry that have not been adequately addressed experimentally.Environmental Hg chemistry requires defining the factors that determine the relative affinities of different ligands for Hg species, as they are critical for understanding its speciation, transformation and bioaccumulation in the environment. Formation constants and the nature of bonding have been determined computationally for environmentally relevant Hg(II) complexes such as chlorides, hydroxides, sulfides and selenides, in various physical phases. Quantum chemistry has been used to determine the driving forces behind the speciation of Hg with hydrochalcogenide and halide ligands. Of particular importance is the detailed characterization of solvation effects. Indeed, the aqueous phase reverses trends in affinities found computationally in the gas phase. Computation has also been used to investigate complexes of methylmercury with (seleno)amino acids, providing a molecular-level understanding of the toxicological antagonism between Hg and selenium (Se). Furthermore, evidence is emerging that ice surfaces play an important role in Hg transport and transformation in polar and alpine regions. Therefore, the diffusion of Hg and its ions through an idealized ice surface has been characterized.Microorganisms are major players in environmental mercury cycling. Some methylate inorganic Hg species, whereas others demethylate methylmercury. Quantum chemistry has been used to investigate catalytic mechanisms of enzymatic Hg methylation and demethylation. The complex interplay between the myriad chemical reactions and transport properties both in and outside microbial cells determines net biogeochemical cycling. In conclusion, prospects for scaling up molecular work to obtain a mechanistic understanding of Hg cycling with comprehensive multiscale biogeochemical modeling are also discussed.
User facility upgrades, new measurement techniques, advances in data analysis algorithms as well as advances in detector capabilities result in an increasing amount of data collected at X-ray beamlines. Some of these data must be analyzed and reconstructed on demand to help execute experiments dynamically and modify them in real time. In turn, this requires a computing framework for real-time processing capable of moving data quickly from the detector to local or remote computing resources, processing data, and returning results to users. In this paper, we discuss the streaming framework built on top of PvaPy, a Python API for the EPICS pvAccess protocol. We describe the framework architecture and capabilities, and discuss scientific use cases and applications that benefit from streaming workflows implemented on top of this framework. We also illustrate the framework's performance in terms of achievable data-processing rates for various detector image sizes.
One of the objectives of these notes is to provide a basic introduction to spectral methods with a particular emphasis on applications to computational fluid dynamics. Another objective is to summarize some of the most important developments in spectral methods in the last two years. The fundamentals of spectral methods for simple problems will be covered in depth, and the essential elements of several fluid dynamical applications will be sketched.
The rapid growth of internet-based applications and the proliferation of networking technologies have been transforming traditional commercial application areas as well as computer and computational sciences and engineering. This growth stimulates the exploration of new, internet-oriented software technologies that can open new research and application opportunities not only for the commercial world, but also for the scientific and high -performance computing applications community. The general goal of this research project is to contribute to better understanding of the transition to internet-based high -performance computing and to develop solutions for some of the difficulties of this transition. More specifically, our goal is to design an architecture for generic divide and conquer internet-based computing, to develop a portable implementation of this architecture, to create an example library of high-performance divide-and-conquer computing agents that run on top of this architecture, and to evaluate the performance of these agents. We have been designing an architecture that incorporates a master task-pool server and utilizes satellite computational servers that operate on the Internet in a dynamically changing large configuration of lower-end nodes provided by volunteer contributors. Our designed architecture is intended to be complementary to and accessible from computational grids such as Globus, Legion, and Condor. Grids provide remote access to existing high-end computing resources; in contrast, our goal is to utilize idle processor time of lower-end internet nodes. Our project is focused on a generic divide-and-conquer paradigm and its applications that operate on a loose and ever changing pool of lower-end internet nodes.
Computational techniques applicable to turbulent boundary layers are classified into solutions of Reynolds-averaged equations, in which all the effects of the turbulence are modelled, and solutions of three-dimensional, time dependent Navier-Stokes equations, in which the large eddies are calculated and only the turbulence at scales smaller than the computational mesh spacings has to be modelled. Current computation costs place engineering computations in the first of these categories; large eddy simulations are appropriate currently for special studies of the dynamical processes of turbulence in idealized flow fields. It is shown that the two methods are interrelated and that each can gain from advances in the other. The degree of success of a pair of increasingly complex Reynolds stress models to broaden their range of applicability is examined through comparisons with experimental data for a variety of flow conditions. An example of a large-eddy simulation is presented, compared with experimental results, and used to evaluate the models for pressure rate-of-strain correlations and dissipation in the Reynolds-averaged equations.
We present a new software, HYPPO, that enables the automatic tuning of hyperparameters of various deep learning (DL) models. Unlike other hyperparameter optimization (HPO) methods, HYPPO uses adaptive surrogate models and directly accounts for uncertainty in model predictions to find accurate and reliable models that make robust predictions. Using asynchronous nested parallelism, we are able to significantly alleviate the computational burden of training complex architectures and quantifying the uncertainty. HYPPO is implemented in Python and can be used with both TensorFlow and PyTorch libraries. We demonstrate various software features on time-series prediction and image classification problems as well as a scientific application in computed tomography image reconstruction. Finally, we show that (1) we can reduce by an order of magnitude the number of evaluations necessary to find the most optimal region in the hyperparameter space and (2) we can reduce by two orders of magnitude the throughput for such HPO process to complete.
As high-end computing systems continue to grow in scale, recent advances in multi- and many-core architectures have pushed such growth toward more dense architectures, that is, more processing elements per physical node, rather than more physical nodes themselves. Although a large number of scientific applications have relied so far on an MPI-everywhere model for programming high-end parallel systems; this model may not be sufficient for future machines, given their physical constraints such as decreasing amounts of memory per processing element and shared caches. As a result, application and computer scientists are exploring alternative programming models that involve using MPI between address spaces and some other threaded model, such as OpenMP, Pthreads, or Intel TBB, within an address space. Such hybrid models require efficient support from an MPI implementation for MPI messages sent from multiple threads simultaneously. In this paper, we explore the issues involved in designing such an implementation. We present four approaches to building a fully thread-safe MPI implementation, with decreasing levels of critical-section granularity (from coarse-grain locks to fine-grain locks to lock-free operations) and correspondingly increasing levels of complexity. We present performance results that demonstrate the performance implications of the different approaches.