Search NASA⌕ Search

SEARCH · Search NASA

Results for “defect structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

Identifying native point defect configurations in α-alumina

Intimately intertwined atomic and electronic structures of point defects govern diffusion-limited corrosion and underpin the operation of optoelectronic devices. For some materials, complex energy landscapes containing metastable defect configurations challenge first-principles modeling efforts. Here, we thoroughly reevaluate native point defect geometries for the illustrative case of α-Al 2 O 3 by comparing three methods for sampling candidate geometries in density functional theory calculations: displacing atoms near a naively placed defect, initializing interstitials at high-symmetry points of a Voronoi decomposition, and Bayesian optimization. We find symmetry-breaking distortions for oxygen vacancies in some charge states, and we identify several distinct oxygen split-interstitial geometries that help explain literature discrepancies involving this defect. We also report a surprising and, to our knowledge, previously unknown trigonal geometry favored by aluminum interstitials in some charge states. Importantly, these new configurations may have transformative impacts on our understanding of defect migration pathways in aluminum-oxide scales protecting metal alloys from corrosion. Overall, the Voronoi scheme appears most effective for sampling candidate interstitial sites because it always succeeded in finding the lowest-energy geometry identified in this study, although no approach found every metastable configuration. Finally, we show that the position of defect levels within the band gap can depend strongly on the defect geometry, underscoring the need to conduct careful searches for ground-state geometries in defect calculations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Two-level structural sparsity regularization for identifying lattices and defects in noisy images

Here, this paper presents a regularized regression model with a two-level structural sparsity penalty applied to locate individual atoms in a noisy scanning transmission electron microscopy image (STEM). In crystals, the locations of atoms is symmetric, condensed into a few lattice groups. Therefore, by identifying the underlying lattice in a given image, individual atoms can be accurately located. We propose to formulate the identification of the lattice groups as a sparse group selection problem. Furthermore, real atomic scale images contain defects and vacancies, so atomic identification based solely on a lattice group may result in false positives and false negatives. To minimize error, model includes an individual sparsity regularization in addition to the group sparsity for a within-group selection, which results in a regression model with a two-level sparsity regularization. We propose a modification of the group orthogonal matching pursuit (gOMP) algorithm with a thresholding step to solve the atom finding problem. The convergence and statistical analyses of the proposed algorithm are presented. The proposed algorithm is also evaluated through numerical experiments with simulated images. The applicability of the algorithm on determination of atom structures and identification of imaging distortions and atomic defects was demonstrated using three real STEM images. In conclusion, we believe this is an important step toward automatic phase identification and assignment with the advent of genomic databases for materials.

36 MATERIALS SCIENCE↗

Procedure for the Transfer of Polymer Films Onto Porous Substrates with Minimized Defects

The fabrication of devices containing thin film structures necessitate the transfer of these films onto the surfaces of arbitrary support substrates. Accomplishing this transfer in a highly controlled, mechanized, and reproducible manner would eliminate the creation of macroscale defect structures (e.g. tears, cracks, and wrinkles) within the thin film that would otherwise have a negative impact on ultimate device performance. In this work, we describe a general protocol for the highly controlled and mechanized transfer of a polymeric thin film onto an arbitrary porous support substrate for eventual use as a water filtration membrane device. Specifically, we fabricate a block copolymer (BCP) thin film on top of a sacrificial, water-soluble poly(acrylic acid) (PAA) layer and silicon wafer substrate. We then utilize a custom-designed, 3D-printed transfer tool and drain chamber system to deposit, lift-off, and transfer the BCP thin film onto the center of a porous anodized aluminum oxide (AAO) support disc. The transferred BCP thin film is shown to be consistently placed onto the center of the support surface due to the guidance of the meniscus. Additionally, we compare our mechanized transfer-processed thin films to those that have been transferred by other commonly used techniques, such as by hand with the use of tweezers. Optical inspection and image analysis of the transferred thin films from the mechanized process confirm that little-to-no macroscale inhomogeneities or plastic deformations are produced, as compared to the multitude of tears and wrinkles produced from manual transfer by hand. Our findings indicate that the proposed strategy for thin film transfer can reduce defects when compared to other methods across many systems and applications.

36 MATERIALS SCIENCE↗

Reducing the deactivation of Ni-metal during the catalytic partial oxidation of a surrogate diesel fuel mixture

Ni catalysts are active and selective for the conversion of hydrocarbon into synthesis gas. However, conventional supported Ni catalysts rapidly deactivate at the high temperatures required for partial oxidation of diesel fuel by sintering and metal vaporization, as well as by carbon deposition and sulfur poisoning. Thus, to reduce deactivation Ni (3 wt%) was substituted into the structures of Ba-hexaaluminate (BNHA) and La–Sr–Zr pyrochlore (LSZN), and their activity was compared to a supported Ni/Al 2 O 3 for the catalytic partial oxidation (CPOX) of a surrogate diesel fuel. Characterization by XRD showed a single phase β-alumina for the hexaaluminate, while LSZN had a pyrochlore structure with a defect SrZrO 3 perovskite phase. Temperature programmed reduction experiments confirmed Ni was reducible in all catalysts. XANES results confirmed that Ni atoms were substituted into the hexaaluminate and pyrochlore structures, as spectra for each catalyst showed different coordination environments for Ni compared to a NiO standard. During CPOX activity tests (T = 900 °C and WHSV = 50,000 scc/g cat /h), the LSZN pyrochlore produced stable H 2 and CO yields in the presence of 5 wt% 1-methylnaphthalene and 50 ppmw dibenzothiophene/n-tetradecane for 2 h, while both Ni/Al 2 O 3 and BNHA catalysts were irreversibly deactivated by this mixture over the same time. Finally, activity loss was strongly linked to carbon formation.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

TiO{sub 2} nanotube arrays for photocatalysis: Effects of crystallinity, local order, and electronic structure

To furnish insight into correlations of electronic and local structure and photoactivity, arrays of short and long TiO{sub 2} nanotubes were synthesized by electrochemical anodization of Ti foil, followed by thermal treatment in O{sub 2} (oxidizing), Ar (inert), and H{sub 2} (reducing) environments. The physical and electronic structures of these nanotubes were probed with x-ray diffraction, scanning electron microscopy, and synchrotron-based x-ray absorption spectroscopy, and correlated with their photocatalytic properties. The photocatalytic activity of the nanotubes was evaluated by monitoring the degradation of methyl orange under UV-VIS light irradiation. Results show that upon annealing at 350 °C all as-anodized amorphous TiO{sub 2} nanotube samples partially transform to the anatase structure, with variations in the degree of crystallinity and in the concentration of local defects near the nanotubes' surface (∼5 nm) depending on the annealing conditions. Degradation of methyl orange was not detectable for the as-anodized TiO{sub 2} nanotubes regardless of their length. However, the annealed long nanotubes demonstrated detectable catalytic activity, which was more significant with the H{sub 2}-annealed nanotubes than with the Ar- and O{sub 2}-annealed nanotube samples. This enhanced photocatalytic response of the H{sub 2}-annealed long nanotubes relative to the other samples is positively correlated with the presence of a larger concentration of lattice defects (such as Ti{sup 3+} and anticipated oxygen vacancies) and a slightly lower degree of crystallinity near the nanotube surface. These physical and electronic structural attributes impact the efficacy of visible light absorption; moreover, the increased concentration of surface defects is postulated to promote the generation of hydroxyl radicals and thus accelerate the photodegradation of the methyl orange. The information obtained from this study provides unique insight into the role of the near-surface electronic and defect structure, crystal structure, and the local chemical environment on the photocatalytic activity and may be employed for tailoring the materials' properties for photocatalysis and other energy-related applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tutorial: Defects in topological semimetals

Three-dimensional topological semimetals are a class of electronic materials in which their bulk and surface states contain linear band touching nodes near the Fermi level. Like semiconductors, their properties will be affected by point and extended defects in their crystal structures, although the extent to which defects and disorders influence topological semimetals may differ in key ways due to their unique electronic structures. In this Tutorial, we provide an overview of the defects in topological semimetals, covering both computational and experimental methods for exploring defect-property relationships. We also include a discussion on open questions that still need to be explored further.

36 MATERIALS SCIENCE↗

Charged Defects in UO 2 Bulk and Surface: A First-Principles Study

Uranium dioxide (UO 2 ) is the primary fuel used in nuclear reactors. Under the extreme heat and radiation inside a reactor, this material inevitably develops defects in its crystal structure. To investigate the nature and behavior of these defects, DFT+U calculations were employed to investigate charged point defects in both bulk UO 2 and its most stable surface, the (111) plane. The formation of defects and their impact on the electronic structure were systematically examined. The results reveal that these defects introduce localized electronic states, alter magnetic behavior, and modify the structural properties. In general, such defects act as deep traps capable of capturing and retaining charge carriers. The stability of these defects depends strongly on the chemical environment and the position of the Fermi level. Surface defect calculations reveal that oxygen vacancies form more readily at the surface than in the bulk over a wide range of electron chemical potential, with subsurface oxygen vacancies being more stable than those in the top layer. Overall, the findings demonstrate how charged defects influence magnetism, transport, and stability in UO 2 , providing insights that may guide improvements in the safety and efficiency of nuclear fuel.

36 MATERIALS SCIENCE↗

Positron annihilation study of vacancy-type defects in Al single crystal foils with the tweed structures across the surface

The vacancy-type defects in the aluminum single crystal foils after a series of the cyclic tensions were studied using positron annihilation. Two components were identified in the positron lifetime spectra associated with the annihilation of free positrons and positrons trapped by dislocations. With increasing number of cycles the dislocation density firstly increases and reaches a maximum value at N = 10 000 cycles but then it gradually decreases and at N = 70 000 cycles falls down to the level typical for the virgin samples. The direct evidence on the formation of a two-phase system “defective near-surface layer/base Al crystal” in aluminum foils at cyclic tension was obtained using a positron beam with the variable energy.

36 MATERIALS SCIENCE↗

Band Structure-Driven Design of a α-CsPbI 3 Ammonia Sensor for Industrial Applications

We investigate the defect-dependent electronic structure and gas-sensing potential of cubic α-CsPbI 3 using first-principles density functional theory and nonadiabatic molecular dynamics. Among the intrinsic defects, interstitials, vacancies, antisites, and switches studied, the I Pb and Pb I antisite defects exhibit transition energy levels near the middle of the band gap, thus functioning as deep traps. Short-term adsorption of ammonia selectively modifies the electronic structure, coordinating with Pb at Pb I sites and Cs at I Pb sites, significantly altering recombination pathways. Detailed analysis reveals that NH 3 reduces anharmonicity at I Pb defects, enabling enhanced recombination at elevated temperatures, while trap-assisted recombination dominates at room temperature. Other analytes, including CH 3 NH 2 and NO 2 , show negligible impact on the band gap or recombination dynamics, highlighting the potential selectivity of NH 3 interactions. Ab initio nonadiabatic molecular dynamics simulations at 300 K and 600 K further demonstrate temperature-dependent modulation of carrier lifetimes, with NH 3 accelerating recombination at ambient conditions and suppressing certain pathways at higher temperatures. These findings suggest that α-CsPbI 3 can serve as a selective and sensitive ammonia sensor over a broad temperature range and offer insights for ammonia detection under industrially relevant conditions.

ammonia sensor↗

Periodic surface structure bifurcation induced by ultrafast laser generated point defect diffusion in GaAs

The formation of high spatial frequency laser induced periodic surface structures (HSFL) with period <0.3 λ in GaAs after irradiation with femtosecond laser pulses in air is studied. We have identified a point defect generation mechanism that operates in a specific range of fluences in semiconductors between the band-gap closure and ultrafast-melt thresholds that produces vacancy/interstitial pairs. Stress relaxation, via diffusing defects, forms the 350–400 nm tall and ∼90 nm wide structures through a bifurcation process of lower spatial frequency surface structures. The resulting HSFL are predominately epitaxial single crystals and retain the original GaAs stoichiometry.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Hydrogen embrittlement of structural steels.

Carbon-manganese steels are candidates for the structural materials in hydrogen gas pipelines, however it is well known that these steels are susceptible to hydrogen embrittlement. Decades of research and industrial experience have established that hydrogen embrittlement compromises the structural integrity of steel components. This experience has also helped identify the failure modes that can operate in hydrogen containment structures. As a result, there are tangible ideas for managing hydrogen embrittement in steels and quantifying safety margins for steel hydrogen containment structures. For example, fatigue crack growth aided by hydrogen embrittlement is a key failure mode for steel hydrogen containment structures subjected to pressure cycling. Applying appropriate structural integrity models coupled with measurement of relevant material properties allows quantification of safety margins against fatigue crack growth in hydrogen containment structures. Furthermore, application of these structural integrity models is aided by the development of micromechanics models, which provide important insights such as the hydrogen distribution near defects in steel structures. The principal objective of this project is to enable application of structural integrity models to steel hydrogen pipelines. The new American Society of Mechanical Engineers (ASME) B31.12 design code for hydrogen pipelines includes a fracture mechanics-based design option, which requires material property inputs such as the threshold for rapid cracking and fatigue crack growth rate under cyclic loading. Thus, one focus of this project is to measure the rapid-cracking thresholds and fatigue crack growth rates of line pipe steels in high-pressure hydrogen gas. These properties must be measured for the base materials but more importantly for the welds, which are likely to be most vulnerable to hydrogen embrittlement. The measured properties can be evaluated by predicting the performance of the pipeline using a relevant structural integrity model, such as that in ASME B31.12. A second objective of this project is to enable development of micromechanics models of hydrogen embrittlement in pipeline steels. The focus of this effort is to establish physical models of hydrogen embrittlement in line pipe steels using evidence from analytical techniques such as electron microscopy. These physical models then serve as the framework for developing sophisticated finite-element models, which can provide quantitative insight into the micromechanical state near defects. Understanding the micromechanics of defects can ensure that structural integrity models are applied accurately and conservatively.

08 HYDROGEN↗

A deep learning interatomic potential developed for atomistic simulation of carbon materials

Interatomic potentials based on neural-network machine learning method have attracted considerable attention in recent years owing to their outstanding ability to balance the accuracy and efficiency in atomistic simulations. In this work, a neural-network potential (NNP) for carbon is generated to simulate the structural properties of various carbon structures. The potential is trained using a database consisting of crystalline and liquid structures obtained by the first-principles density functional theory (DFT) calculations. The developed potential accurately predicts the energies and forces in crystalline and liquid carbon structures, the energetic stability of defected graphene, and the structures of amorphous carbon as the function of density. As a result, the excellent accuracy and transferability of the NNP provide a promising tool for accurate atomistic simulations of various carbon materials with faster speed and much lower cost.

36 MATERIALS SCIENCE↗

Intergrowth structure of α-phase in β-type TmAlB{sub 4} compound studied by high-angle annular detector dark-field scanning transmission electron microscopy

Nanostructure of a ThMoB{sub 4}-type (β-type) TmAlB{sub 4} compound, in which YCrB{sub 4}-type (α-type) domains are locally intergrown, is studied by high-angle annular detector dark-field scanning transmission electron microscopy (HAADF-STEM). Z-contrast images by HAADF-STEM directly represent the arrangements of Tm atoms located at centers of heptagonal atomic columns of B atoms as bright dots, and give us detailed information of intergrowth of type domains in the matrix of the β-type phase, which coherently occurs. Structural and bonding analyses for β-TmAlB{sub 4} point out the closeness in atomic interactions and energy of the α- and β-type structures which support the easy formation of such nanostructure intergrowths. From combination between HAADF-STEM and electronic structure calculation, a detailed local crystal structure with intrinsic building defects is effectively revealed. - Graphical abstract: Nanostructure of a ThMoB{sub 4}-type (β-type) TmAlB{sub 4} compound, in which YCrB{sub 4}-type (α-type) domains are locally intergrown, is studied by high-angle annular detector dark-field scanning transmission electron microscopy (HAADF-STEM). Z-contrast images by HAADF-STEM directly represent arrangements of Tm atoms located at centers of heptagonal atomic columns of B atoms as bright dots, and give us detailed information of the characteristic intergrowth structure of type domains in the matrix of the β-type phase. - Highlights: • HAADF-STEM images directly represent arrangements of Tm atoms as bright dots. • The α-type planar domains coherently intergrown in the β-type matrix. • Bright strips appear at overlapped regions of Tm hexagons along interfaces between α- and β-type domains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural Tolerance Factor Approach to Defect-Resistant I 2 -II-IV-X 4 Semiconductor Design

Recent work on quaternary semiconductors Cu 2 BaSn(S,Se) 4 and Ag 2 BaSnSe 4 for photovoltaic and thermoelectric applications, respectively, has shown the promise of exploring the broader family of defect-resistant I 2 -II-IV-X 4 materials (where I, II, and IV refer to the formal oxidation state of the metal cations and X is a chalcogen anion) with tetrahedrally coordinated I/IV cations and larger II cations (i.e., Sr, Ba, Pb, and Eu) for optoelectronic and energy-related applications. Chemical dissimilarity among the II and I/IV atoms represents an important design motivation because it presents a barrier to antisite formation, which otherwise may act as electronically harmful defects. We herein show how all 31 experimentally reported I 2 -II-IV-X 4 examples (with large II cations and tetrahedrally coordinated smaller I/IV cations), which form within five crystal structure types, are structurally linked. Based on these structural similarities, we derive a set of tolerance factors that serve as descriptors for phase stability within this family. Despite common usage in the well-studied perovskite system, Shannon ionic radii are found to be insufficient for predicting metal–chalcogen bond lengths, pointing to the need for experimentally derived correction factors as part of an empirically driven learning approach to structure prediction. Here, we use the tolerance factors as a predictive tool and demonstrate that four new I 2 -II-IV-X 4 compounds, Ag 2 BaSiS 4 , Ag 2 PbSiS 4 , Cu 2 PbGeS 4 , and Cu 2 SrSiS 4 , can be synthesized in correctly predicted phases. One of these compounds, Ag 2 PbSiS 4 , shows potentially promising optoelectronic properties for photovoltaic applications.

36 MATERIALS SCIENCE↗

Self-generated magnetic fields in direct-drive implosion experiments

Electric and self-generated magnetic fields in direct-drive implosion experiments on the OMEGA Laser Facility were investigated employing radiography with ∼10- to 60-MeV protons. The experiment used plastic-shell targets with imposed surface defects (glue spots, wires, and mount stalks), which enhance self-generated fields. The fields were measured during the 1-ns laser drive with an on-target intensity ∼10{sup 15} W/cm{sup 2}. Proton radiographs show multiple ring-like structures produced by electric fields ∼10{sup 7} V/cm and fine structures from surface defects, indicating self-generated fields up to ∼3 MG. These electric and magnetic fields show good agreement with two-dimensional magnetohydrodynamic simulations when the latter include the ∇T{sub e} × ∇n{sub e} source, Nernst convection, and anisotropic resistivity. The simulations predict that self-generated fields affect heat fluxes in the conduction zone and, through this, affect the growth of local perturbations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗