Search NASA⌕ Search

SEARCH · Search NASA

Results for “graphitic structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

Friction and wear of carbon-graphite materials for high energy brakes

Caliper-type brakes simulation experiments were conducted on seven different carbon-graphite material formulations against a steel disk material and against a carbon-graphite disk material. The effects of binder level, boron carbide (B4C) additions, graphite fiber additions, and graphite cloth reinforcement on friction and wear behavior were investigated. Reductions in binder level and additions of B4C each resulted in increased wear. The wear rate was not affected by the addition of graphite fibers. Transition to severe wear and high friction was observed in the case of graphite-cloth-reinforced carbon sliding against a disk of similar composition. This transition was related to the disruption of a continuous graphite shear film that must form on the sliding surfaces if low wear is to occur. The exposure of the fiber structure of the cloth constituent is believed to play a role in the shear film disruption.

Bill, R. C.↗

Study of noise reduction characteristics of double-wall panels

The noise reduction characteristics of general aviation type, flat, double-wall structures were investigated. The experimental study was carried out on 20-by-20 inch panels with an exposed area of 18 by 18 inches. A frequency range from 20 to 5000 Hz was covered. The experimental results, in general, follow the expected trends. At low frequencies the double-wall structures are no better than the single-wall structures. However, for depths normally used in the general aviation industry, the double-wall panels are very attractive. The graphite-spoxy skin panels have higher noise reduction at very low frequencies ( 100 Hz) than the Kevlar skin panels. But the aluminum panels have higher noise reduction in the high frequency region, due to their greater mass. Use of fiberglass insulation is not effective in the low frequency region, and at times it is even negative. But the insulation is effective in the high-frequency region. The theoretical model for predicting the transmission loss of these multilayered panels is also discussed.

Navaneethan, R.↗

Advanced materials for space nuclear power systems

The overall philosophy of the research was to develop and characterize new high temperature power conversion and radiator materials and to provide spacecraft designers with material selection options and design information. Research on three candidate materials (carbide strengthened niobium alloy PWC-11 for fuel cladding, graphite fiber reinforced copper matrix composites for heat rejection fins, and tungsten fiber reinforced niobium matrix composites for fuel containment and structural supports considered for space power system applications is discussed. Each of these types of materials offers unique advantages for space power applications.

Titran, Robert H.↗

Free vibrations of thin-walled semicircular graphite-epoxy composite frames

A detailed study is made of the effects of variations in lamination and material parameters of thin-walled composite frames on their vibrational characteristics. The structures considered are semicircular thin-walled frames with I and J sections. The flanges and webs of the frames are modeled by using two-dimensional shell and plate finite elements. A mixed formulation is used with the fundamental unknowns consisting of both the generalized displacements and stress resultants in the frame. The frequencies and modes predicted by the two-dimensional finite-element model are compared with those obtained from experiments, as well as with the predictions of a one-dimensional, thin-walled-beam, finite-element model. A detailed study is made of the sensitivity of the vibrational response to variations in the fiber orientation, material properties of the individual layers, and boundary conditions.

Noor, Ahmed K.↗

Advanced materials for space nuclear power systems

The overall philosophy of the research was to develop and characterize new high temperature power conversion and radiator materials and to provide spacecraft designers with material selection options and design information. Research on three candidate materials (carbide strengthened niobium alloy PWC-11 for fuel cladding, graphite fiber reinforced copper matrix composites for heat rejection fins, and tungsten fiber reinforced niobium matrix composites for fuel containment and structural supports) considered for space power system applications is discussed. Each of these types of materials offers unique advantages for space power applications.

Titran, Robert H.↗

Visualizing Individual Nitrogen Dopants in Monolayer Graphene

In monolayer graphene, substitutional doping during growth can be used to alter its electronic properties. We used scanning tunneling microscopy, Raman spectroscopy, x-ray spectroscopy, and first principles calculations to characterize individual nitrogen dopants in monolayer graphene grown on a copper substrate. Individual nitrogen atoms were incorporated as graphitic dopants, and a fraction of the extra electron on each nitrogen atom was delocalized into the graphene lattice. The electronic structure of nitrogen-doped graphene was strongly modified only within a few lattice spacings of the site of the nitrogen dopant. These findings show that chemical doping is a promising route to achieving high-quality graphene films with a large carrier concentration.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Sensitivity Analysis of an Experimental Breeder Reactor II Fuel Assembly

The Experimental Breeder Reactor II (EBR-II) was selected as a candidate for a reactor physics benchmark evaluation due to its unique features and capabilities. In connection with the benchmark evaluation, the goal of this work was to perform a sensitivity analysis. The EBR-II was a sodium cooled, pool type, metal fueled, fast spectrum reactor. EBR-II operated from 1964 through 1994. It had a maximum heat output of 62.5 MW which could produce 20 MW of electricity. The design of EBR-II consisted of 637 hexagonal shaped, removable assemblies. The assemblies were divided into three regions: the core, an inner blanket, and an outer blanket. The core region contained assemblies with 91 fuel rods in each. The fuel was enriched uranium metal and was clad within stainless steel. The core region also included two safety assemblies and eight control assemblies with the difference being that these assemblies only contained 61 fuel rods. Additional assemblies in the core region included stainless steel dummies, half worth drivers, and experimental/instrumentation assemblies. The inner blanket region initially consisted of depleted uranium for fuel breeding, but was replaced, after proving the concept of breeding, with stainless steel reflectors for the purpose of irradiation. The outer blanket region consisted of depleted uranium. Figure 1 shows a cross section view of the EBR-II core layout. Each assembly was approximately 234 cm long with the uranium fuel section being 33 cm long. Above and below the fuel were stainless steel neutron reflectors. Additionally, orifices at the bottom of the assembly allowed for sodium coolant to flow upward, with larger holes in the subassemblies at the center where the greatest heat was produced. The core of EBR-II was enclosed by a stainless steel reactor vessel which was comprised of a radial shell, a lower grid plenum structure, and an upper reactor vessel cover that served as a neutron shield. Surrounding the reactor vessel radially were layers of graphite and borated graphite shielding. The entire assembly is submerged 3 meters in a pool of sodium. The pool contained up to 337,000 liters of sodium which was forced through the core and blanket regions using two centrifugal pumps that were also submerged within the sodium pool. The design of EBR-II included many safety features. The compatibility between the sodium and stainless steel prevented corrosion and therefore the risk of a radioactive release due to corrosion. The sodium coolant was kept at near atmospheric pressure which made any leak more controllable. The metal fuel, cladding, and coolant allowed for heat to be removed easily. The large volume of sodium allowed for heat to be absorbed without problems occurring. Lastly, the reactor would expand as temperature increased which would result in greater neutron leakage. This extra leakage caused a large negative temperature reactivity feedback which automatically shut the reactor down in case of an accident. EBR-II had unique capabilities which were proven during the Integral Fast Reactor initiative. This program lasted from 1984 to 1994. The goal of this program was to solve many of the perceived problems with nuclear energy through scientific means. The safety features of EBR-II were put to the test in April 1986. The tests simulated loss of reactor coolant flow and loss of a heat sink. For both of these tests, the reactor was at 100% power and was not scrammed. During both tests, the reactor shut itself down and achieved a safe steady state temperature all due to the design of the reactor. It was because of these tests that EBR-II was chosen for a reactor physics benchmark evaluation. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Hierarchical Model for the Analysis of Scattering Data of Complex Materials

Interpreting the results of scattering data for complex materials with a hierarchical structure in which at least one phase is amorphous presents a significant challenge. Often the interpretation relies on the use of large-scale molecular dynamics (MD) simulations, in which a structure is hypothesized and from which a radial distribution function (RDF) can be extracted and directly compared against an experimental RDF. This computationally intensive approach presents a bottleneck in the efficient characterization of the atomic structure of new materials. Here, we propose and demonstrate an approach for a hierarchical decomposition of the RDF in which MD simulations are replaced by a combination of tractable models and theory at the atomic scale and the mesoscale, which when combined yield the RDF. We apply the procedure to a carbon composite, in which graphitic nanocrystallites are distributed in an amorphous domain. We compare the model with the RDF from both MD simulation and neutron scattering data. Ultimately, this procedure is applicable for understanding the fundamental processing-structure-property relationships in complex magnetic materials.

36 MATERIALS SCIENCE↗

Electrochemical carbon deposition from CO 2 in molten carbonates: substrate-dependent growth

Electrochemical carbon deposition from molten carbonate salts using inert electrodes and no additional catalyst is systematically examined. At sufficiently cathodic potentials, carbon formation occurs within 30 min and transitions from substrate-dependent nucleation to carbon-on-carbon growth. Although deposits formed on either mild-steel or graphite cathodes exhibit comparable thicknesses and salt contents, their macrostructures differ, reflecting differences in early-stage growth rates and surface chemistry. Characterization by ICP-OES, Raman spectroscopy, SEM/EDS, synchrotron powder X-ray diffraction, and C K-edge X-ray absorption near edge structure reveals that the as-deposited carbon is predominantly disordered sp 2 -bonded material. However, post-treatment reveals latent turbostratic ordering in select samples, indicating that short-range order is established during deposition but is obscured by an entrained electrolyte and kinetically formed amorphous phases. No anode-derived contamination is detected, and carbon grown on graphite cathodes shows minimal metallic impurities. These results clarify the role of cathode surface chemistry and provide pathways for controlling electrode-derived impurity incorporation and carbon structure in catalyst-free molten carbonate systems.

36 MATERIALS SCIENCE↗

Multilayer graphane synthesized under high hydrogen pressure

A new hydrocarbon – hydrographite – with the composition close to CH is shown to form from graphite and gaseous hydrogen at pressures above 2 GPa and temperatures from 450 to 700 °C. Hydrographite is a black solid thermally stable under ambient conditions. When heated in vacuum, it decomposes into graphite and molecular hydrogen at temperatures from 500 to 650 °C. Powder X-ray diffraction characterizes hydrographite as a multilayer “graphane II” phase predicted by ab initio calculations [Wen X-D et al. PNAS 2011; 108:6833] and consisting of graphane sheets in the chair conformation stacked along the hexagonal c axis in the -ABAB- sequence. The crystal structure of the synthesized phase belongs to the P63mc space group. Moreover, the unit cell parameters are a = 2.53(1) Å and c = 9.54(1) Å and therefore exceed the corresponding parameters of graphite by 2.4(2)% and 42.0(3)%. Stretching vibrations of C–H groups on the surface of the hydrographite particles are examined by infrared spectroscopy.

36 MATERIALS SCIENCE↗

Graphite oxide-mediated synthesis of porous CeO{sub 2} quadrangular prisms and their high-efficiency adsorptive performance

Graphical abstract: - Highlights: • Porous CeO{sub 2} quadrangular prisms have been prepared via graphite oxide-mediated synthesis. • Dual-pore hierarchical systems are formed with the pore distributions around 4 nm and 30 nm. • Porous CeO{sub 2} exhibits a rapid adsorption to Rhodamine B with a removal efficiency of ∼99%. • Porous CeO{sub 2} retains the same performances in different pH solutions. - Abstract: We report a graphite oxide-mediated approach for synthesizing porous CeO{sub 2} through a facile hydrothermal process followed by thermal annealing in air. The phase structure, morphology, microstructure and porosity of the products have been revealed by a combination of X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and N{sub 2} adsorption. The as-prepared CeO{sub 2} products show well-defined quadrangular prism morphology, and they are composed of interconnected nanoparticles with diameters around 30–100 nm. In particular, the dual-pore hierarchical systems are created in the CeO{sub 2} quadrangular prisms with the pore distributions around 4 nm and 30 nm. The dye sorption capacity of the porous CeO{sub 2} is investigated, which exhibits a rapid adsorption to rhodamine B with a high removal efficiency of ∼99%. Moreover, the CeO{sub 2} absorbent retains the same performances in different pH solutions.

36 MATERIALS SCIENCE↗

Thermal control structure and garment

A flexible thermally conductive structure. The structure generally includes a plurality of thermally conductive yarns, at least some of which are at least partially disposed adjacent to an elastomeric material. Typically, at least a portion of the plurality of thermally conductive yarns is configured as a sheet. The yarns may be constructed from graphite, metal, or similar materials. The elastomeric material may be formed from urethane or silicone foam that is at least partially collapsed, or from a similar material. A thermal management garment is provided, the garment incorporating a flexible thermally conductive structure.

36 MATERIALS SCIENCE↗

Advanced Low-Flammable Electrolytes for Stable Operation of High-Voltage Lithium-Ion Batteries

Despite being an effective flame retardant, trimethyl phosphate (TMP a ) is generally considered as an unqualified solvent for fabricating electrolytes used in graphite (Gr) based lithium ion batteries as it readily leads to Gr exfoliation and cell failure. In this work, by adopting the unique solvation structure of localized high-concentration electrolyte (LHCE) to TMP a and tuning the composition of the solvation sheath via electrolyte additive, excellent electrochemical performance can be achieved with TMPa based electrolytes in Gr||LiNi 0.8 Mn 0.1 Co 0.1 O 2 cells. After 500 charge/discharge cycles within the voltage range of 2.5-4.4 V, the batteries containing TMPa based LHCEs with proper additive can achieve a capacity retention of 85.4%, being significantly higher than cells using a LiPF 6 -organocarbonates baseline electrolyte (75.2%). Meanwhile, due to the flame retarding effect of TMP a , TMP a based LHCEs exhibit significantly reduced flammability compared with the conventional LiPF 6 -organocarbonates electrolyte.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimization of structural and energy characteristics of adsorbents for methane storage

Using numerical and analytical methods, a model for microporous carbon adsorbents with slit-shaped pores of different widths was developed. Such pores are formed during activation procedure by the removal of the hexagonal carbon layers burnt out in a graphite-like crystallites. Dubinin’s theory of volume filling of micropores was used to calculate methane adsorption equilibria on these model adsorbents. Isobaric dependences of methane adsorption on pore width, specific micropore volumes, and the specific surface were plotted in the range of pressures from 1 to 10 MPa. It was found that the isobaric adsorption curves had a maximum the position of which depends on both the structural-energy characteristics of the adsorbent and thermodynamic conditions chosen to operate the adsorption system. As pressure increased, the maximum of adsorption shifts to the porous systems with wider pores and larger micropore volume.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Assembling Si 2 BN nanoribbons into a 3D porous structure as a universal anode material for both Li- and Na-ion batteries with high performance

The development of anode materials is critical to the success of sodium ion batteries (SIBs). Because of the size difference between Li and Na, the commercial anode material graphite in Li-ion batteries does not work for Na-ion batteries. Thus, it will be ideal if some universal anode materials could work for both Li- and Na-ion batteries with high performance. Inspired by a recent study on the high performance of a 2D-Si 2 BN sheet as an anode material for Li-ion batteries, we design a three dimensional (3D) porous structure by using the nanoribbons of a Si 2 BN sheet as building blocks. Based on the state-of-the-art ab initio calculations, we find that the resulting 3D porous Si 2 BN structure is stable chemically, dynamically and thermally, exhibiting a high specific capacity of 512.42 (341.61 mA h g -1 ), a low voltage of 0.27 V (0.15 V), a small volume expansion of 2.5% (2.7%), and a low migration energy barrier of 0.44 eV (0.19 eV) for Li- (Na-) ion batteries. Finally, these intriguing features, together with the light mass and rich abundance of Si, B and N, suggest that the 3D porous Si2BN structure is a promising candidate for the anode material of both Li- and Na-ion batteries.

36 MATERIALS SCIENCE↗

Formation of TiC-core, Graphitic-mantle Grains from CO Gas

We demonstrate a new formation route for TiC-core, graphitic-mantle spherules that does not require c-atom addition and the very long timescales associated with such growth (Bernatowicz et al. 1996). Carbonaceous materials can also be formed from C2H2 and its derivatives, as well as from CO gas. In this paper, we will demonstrate that large cage structure carbon particles can be produced from CO gas by the Boudouard reaction. Since the sublimation temperature for such fullerenes is low, the large cages can be deposited onto previously-nucleated TiC and produce TiC-core, graphitic-mantle spherules. New constraints for the formation conditions and the timescale for the formation of TiC-core, graphitic-mantle spherules are suggested by the results of this study. In particular, TiC-core, graphitic-mantle grains found in primitive meteorites that have never experienced hydration could be mantled by fullerenes or carbon nanotubes rather than by graphite. In situ observations of these grains in primitive anhydrous meteoritic matrix could confirm or refute this prediction and would demonstrate that the graphitic mantle on such grains is a metamorphic feature due to interaction of the pre-solar fullerenes with water within the meteorite matrix.

Kimura, Yuki↗

Do Ag{sub n} (up to n = 8) clusters retain their identity on graphite? Insights from first-principles calculations including dispersion interactions

Adsorption of pre-formed Ag{sub n} clusters for n = 1 − 8 on a graphite substrate is studied within the density functional theory employing the vdW-DF2 functional to treat dispersion interactions. Top sites above surface layer carbon atoms turn out to be most favorable for a Ag adatom, in agreement with experimental observations. The same feature is observed for clusters of almost all sizes which have the lowest energies when the Ag atoms are positioned over top sites. Most gas phase isomers retain their structures over the substrate, though a couple of them undergo significant distortions. Energetics of the adsorption can be understood in terms of a competition between energy cost of disturbing Ag–Ag bonds in the cluster and energy gain from Ag–C interactions at the surface. Ag{sub 3} turns out to be an exceptional candidate in this regard that undergoes significant structural distortion and has only two of the Ag atoms close to surface C atoms in its lowest energy structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electronic Structures, Bonding Configurations, and Band-Gap-Opening Properties of Graphene Binding with Low-Concentration Fluorine

To better understand the effects of low-level fluorine in graphene-based sensors, first-principles density functional theory (DFT) with van der Waals dispersion interactions has been employed to investigate the structure and impact of fluorine defects on the electrical properties of single-layer graphene films. The results show that both graphite-2H and graphene have zero band gaps. When fluorine bonds to a carbon atom, the carbon atom is pulled slightly above the graphene plane, creating what is referred to as a CF defect. The lowest-binding energy state is found to correspond to two CF defects on nearest neighbor sites, with one fluorine above the carbon plane and the other below the plane. Overall this has the effect of buckling the graphene. The results further show that the addition of fluorine to graphene leads to the formation of an energy band (BF) near the Fermi level, contributed mainly from the 2p orbitals of fluorine with a small contribution from the porbitals of the carbon. Among the 11 binding configurations studied, our results show that only in two cases does the BF serve as a conduction band and open a band gap of 0.37 eV and 0.24 eV respectively. The binding energy decreases with decreasing fluorine concentration due to the interaction between neighboring fluorine atoms. The obtained results are useful for sensor development and nanoelectronics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗