Search NASA⌕ Search

SEARCH · Search NASA

Results for “subsurface flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

Pore-scale study of capillary trapping mechanism during CO2 injection in geological formations

Geological sequestration of CO{sub 2} gas emerged as a promising solution for reducing amount of green house gases in atmosphere. A number of continuum scale models are available to describe the transport phenomena of CO{sub 2} sequestration. These models rely heavily on a phenomenological description of subsurface transport phenomena and the predictions can be highly uncertain. Pore-scale models provide a better understanding of fluid displacement processes, nonetheless such models are rare. In this work we use a Smoothed Particle Hydrodynamics (SPH) model to study pore-scale displacement and capillary trapping mechanisms of super-critical CO{sub 2} in the subsurface. Simulations are carried out to investigate the effects of gravitational, viscous, and capillary forces in terms of Gravity, Capillary, and Bond numbers. Contrary to the other published continuum scale investigations, we found that not only Gravity number but also Capillary number plays an important role on the fate of injected CO{sub 2}. For large Gravity numbers (on the order of 10), most of the injected CO{sub 2} reaches the cap-rock due to gravity segregation. A significant portion of CO{sub 2} gets trapped by capillary forces when Gravity number is small (on the order of 0.1). When Gravity number is moderately high (on the order of 1), trapping patterns are heavily dependent on Capillary number. If Capillary number is very small (less than 0.001), then capillary forces dominate the buoyancy forces and a significant fraction of injected CO{sub 2} is trapped by the capillary forces. Conversely, if Capillary number is high (higher than 0.001), capillary trapping is relatively small since buoyancy dominates the capillary forces. In addition, our simulations reveal different types of capillary trapping and flow displacement mechanisms during and after injection. In gravity dominated cases leave behind was the widespread trapping mechanism. Division was the primary trapping mechanism in viscous dominated cases. In capillary dominated cases, snap-off of the CO{sub 2} plume is the most commonly observed displacement mechanism. Large CO{sub 2} blobs are created due to coalescence mechanism.

54 ENVIRONMENTAL SCIENCES↗

Thorium Enrichment within the Procellarum KREEP Terrane: The Record in Surface Deposits and Significance for Thermal Evolution

The nearside-farside structural and compositional asymmetry of the Moon was recognized during the early days of Apollo and the suggestion was made that the migration of mantle melts to the nearside would have been favored by early Earth-Moon orbital dynamics and nonuniform planetesimal bombardment. Recent global geochemical mapping by Lunar Prospector has provided additional data, particularly in the Th distribution, that strongly supports the notion of global, preferential melt migration, which led in part to the development of the Procellarum KREEP Terrane (PKT) [2-5]. The surface distribution of Th was then reshaped by basin-forming impacts into the PKT, especially the Imbrium impact, which was the last and largest to strike in that region. The Imbrium event probably excavated material from a partially molten zone deep in the crust and delivered Th-rich ejecta Moon-wide. A fundamentally important but poorly understood aspect of the global Th distribution is the concentration of Th in the subsurface rocks of the PKT crustal section. For example, depending on what assumptions are made, the PKT crustal section, which is about 12% of the crust and only about 1.2% of the whole Moon, may contain as much as 40% of the Moon's entire Th budget. Such a distribution of Th and related heat-producing elements would have had a profound effect on melting, mixing, and the thermal evolution of the PKT and the underlying mantle. In this abstract, we examine the compositions of terra formations within the PKT and relate them to some of the Th-bearing rock types known from the Apollo samples. It appears that the existence of the PKT may be a unifying concept for a number of petrologic and geochemical observations. From the initial Lunar Prospector gamma-ray spectrometer data(-about 5 deg. resolution) and from the preliminary low-orbit data, there appears to be a number of relatively hotter "spots" within the PKT in terms of Th concentration. Some of the hotter spots correspond to intermediate-sized craters that penetrated volcanic flows and excavated Th-rich, submare material, such as Aristarchus, Aristillus, and Kepler. Other spots, however, correspond to surficial formations that constitute mainly rough topography associated with Imbrium ejecta or circum-Imbrium ring mountains and do not necessarily imply the presence of exposed KREEP basalts. The Fra Mauro Formation south of Copernicus toward the Apollo 14 site and regions of the Alpes Formation southwest of Copernicus in the vicinity of Reinhold lie within the most prominent hotspot; here them concentration is consistent with that found in the Apollo 14 soils (about 12-13 ppm) when the proportions of Fra Mauro Formation and mare basalt are considered. The area between Copernicus and Kepler and northwest of Copernicus in terra extending to the Carpathians is similarly enriched in Th. The Apennines from Eratosthenes toward the Apollo 15 site contain elevated Th concentrations, as does the northwestern quadrant of circum-Imbrium terra, especially between (but not including) La Condamine and Plato, and in the region northwest of the Jura mountains extending southward past Mairan to the Gruithuisen-Domes region. Within the main topographic rim of Imbrium, the Apennine Bench formation south of Archimedes appears to have relatively elevated Th concentration. Comparing the map of Th distribution to a digital-elevation map derived from Clementine altimetry, it appears that most of the areas richest in Th occur where the surface is elevated relative to the majority of PKT volcanic plains. Not all rough topography within the PKT has such elevated Th, however. Based on an analysis of the 5 deg. data, and using the calibration of, the mean Th concentrations for mainly volcanic-resurfaced terrain and rugged terrain are similar (about 5.5 ppm). This occurs in part because craters that penetrated mare basalt excavated Th-rich material. Even so, there appear to be extensive areas of volcanic resurfacing that have no obvious extrinsic source of Th-rich material, suggesting that the basalts, themselves, may contain as much as 5-6 ppm Th. High-FeO concentrations (18 to >20 wt%) indicate that these are not KREEP basalts but mare basalts. If so, this is surprising because most of the Apollo-sampled mare basalts have very low-Th (typically <2 ppm). A variety of Th-rich materials occur in the sample collection, particularly in the samples from the Apollo 12,14, and 15 sites. The most abundant Th-rich rock types are the mafic impact-melt breccias, which although found at all sites, are most abundant at Apollo 14, where they dominate the rock samples and make up some 40% of the rock particles in the soil. These have Th concentrations ranging up to about 30 ppm and averaging about 18 ppm. The Apollo 14 soils contain about 13 ppm Th, reflecting the high abundance of this melt-breccia component. At the nearby Apollo 12 site, the rocks consist mainly of mare basalts, and these have low-Th concentrations, mostly <1 ppm. Among the nonmare rocks, however, a few such as complex breccia 12013 contain a variety of evolved lithologies and represent potential sources of Th-rich components ranging from 17 to 50 ppm. A single fragment of KREEP basalt from the Apollo 12 soil contains about 50 ppm Th. Despite the identification of highly Th-enriched lithologic components at the Apollo 12 site, the soils there vary linearly in composition so as to extrapolate to a moderate Th KREEP-basalt component or a composition like that of the Fra Mauro formation as reflected by Apollo 14 soil (14 ppm Th at 10 wt% FeO). The nearby Lansberg Crater (39-km diameter) is a likely candidate to have delivered submare material such as buried Fra Mauro or Alpes material to the Apollo 12 site. Additional information contained in the original.

Jolliff, B. L.↗

Crustal deformation, the earthquake cycle, and models of viscoelastic flow in the asthenosphere

The crustal deformation patterns associated with the earthquake cycle can depend strongly on the rheological properties of subcrustal material. Substantial deviations from the simple patterns for a uniformly elastic earth are expected when viscoelastic flow of subcrustal material is considered. The detailed description of the deformation pattern and in particular the surface displacements, displacement rates, strains, and strain rates depend on the structure and geometry of the material near the seismogenic zone. The origin of some of these differences are resolved by analyzing several different linear viscoelastic models with a common finite element computational technique. The models involve strike-slip faulting and include a thin channel asthenosphere model, a model with a varying thickness lithosphere, and a model with a viscoelastic inclusion below the brittle slip plane. The calculations reveal that the surface deformation pattern is most sensitive to the rheology of the material that lies below the slip plane in a volume whose extent is a few times the fault depth. If this material is viscoelastic, the surface deformation pattern resembles that of an elastic layer lying over a viscoelastic half-space. When the thickness or breath of the viscoelastic material is less than a few times the fault depth, then the surface deformation pattern is altered and geodetic measurements are potentially useful for studying the details of subsurface geometry and structure. Distinguishing among the various models is best accomplished by making geodetic measurements not only near the fault but out to distances equal to several times the fault depth. This is where the model differences are greatest; these differences will be most readily detected shortly after an earthquake when viscoelastic effects are most pronounced.

Cohen, S. C.↗

Crustal deformation, the earthquake cycle, and models of viscoelastic flow in the asthenosphere

The crustal deformation patterns associated with the earthquake cycle can depend strongly on the rheological properties of subcrustal material. Substantial deviations from the simple patterns for a uniformly elastic earth are expected when viscoelastic flow of subcrustal material is considered. The detailed description of the deformation pattern and in particular the surface displacements, displacement rates, strains, and strain rates depend on the structure and geometry of the material near the seismogenic zone. The origin of some of these differences are resolved by analyzing several different linear viscoelastic models with a common finite element computational technique. The models involve strike-slip faulting and include a thin channel asthenosphere model, a model with a varying thickness lithosphere, and a model with a viscoelastic inclusion below the brittle slip plane. The calculations reveal that the surface deformation pattern is most sensitive to the rheology of the material that lies below the slip plane in a volume whose extent is a few times the fault depth. If this material is viscoelastic, the surface deformation pattern resembles that of an elastic layer lying over a viscoelastic half-space. When the thickness or breath of the viscoelastic material is less than a few times the fault depth, then the surface deformation pattern is altered and geodetic measurements are potentially useful for studying the details of subsurface geometry and structure. Distinguishing among the various models is best accomplished by making geodetic measurements not only near the fault but out to distances equal to several times the fault depth. This is where the model differences are greatest; these differences will be most readily detected shortly after an earthquake when viscoelastic effects are most pronounced.

Cohen, S. C.↗

Riverbed Hydrologic Exchange Dynamics in a Large Regulated River Reach

Hydrologic exchange flux (HEF) is an important hydrologic component in river corridors that includes both bidirectional (hyporheic) and unidirectional (gaining/losing) surface water – groundwater exchanges. Quantifying HEF rates in a large regulated river is difficult due to the large spatial domains, complexity of geomorphologic features and subsurface properties, and the great stage variations created by dam operations at multiple time scales. In this study, we developed a method that combined numerical modeling and field measurements for estimating HEF rates across the river bed in a 7-km long reach of the highly regulated Columbia River. A high-resolution computational fluid dynamics (CFD) modeling framework was developed and validated by field measurements and other modeling results to characterize the HEF dynamics across the river bed. We found that about 85% of the time from 2008-2014 the river was losing water with an annual average net HEF rates across the river bed (Qz) of -2.3 m 3 s -1 (negative indicating downwelling). June was the only month that the river gained water, with monthly averaged Qz of 0.8 m 3 s -1 . We also found that the daily dam operations increased the hourly gross gaining and losing rate over an average year of 8% and 2%, respectively. By investigating the HEF feedbacks at various time scales, we suggest that the dam operations could reduce the HEF at seasonal time scale by decreasing the seasonal flow variations, while also enhance the HEF at sub-daily time scale by generating high frequency discharge variations. These changes could generate significant impacts on biogeochemical processes in the hyporheic zone.

54 ENVIRONMENTAL SCIENCES↗

Final report of “A Detailed Study of the Physical Mechanisms Controlling CO2-Brine Capillary Trapping in the Subsurface” (University of Arizona, DE-SC0006696)

Carbon capture and storage (CCS) of carbon dioxide emissions generated by production or combustion of fossil fuels is a technologically viable means to reduce the build-up of CO2 in the atmosphere and oceans. Using advantages of scale and location, CCS is particularly suitable for large point sources near ubiquitous deep saline aquifers, depleted gas reservoirs, or at production reservoirs for enhanced oil recovery (EOR). In the BES-funded research project, Oregon State University (OSU) carried out capillary trapping experiments with proxy fluids that mimic the properties of the scCO2/brine system under ambient temperatures and pressures, and successfully developed a unique and novel x-ray compatible, high-pressure, elevated temperature setup to study the scCO2/brine system under challenging reservoir conditions. Both methodologies were applied to a variety of porous media, including synthetic (glass bead) and geologic (Bentheimer sandstone) materials. The University of Arizona (UA) developed pore-scale lattice Boltzmann (LB) models which are able to handle the experimental conditions for proxy fluids, as well as the scCO2/brine system, that are capable of simulating permeability in volumes of tens of millions of fluid elements. We reached the following summary findings (main institute indicated): 1. (OSU/UA) To understand capillary trapping in a multiphase fluid-porous medium system, the system must be analyzed from a pore-scale force balance perspective; trapping can be enhanced by manipulating wetting and nonwetting phase fluid properties. 2. (OSU) Pore-scale fluid connectivity and topology has a clear and direct effect on nonwetting phase capillary trapping efficiency. 3. (OSU) Rock type and flow regime also have a pronounced effects on capillary trapping. 4. (OSU/UA) There is a predictable relationship between NWP connectivity and NWP saturation, which allows for development of injection strategies that optimize trapping. The commonly used Land model (Land, 1968) does not predict amount of trapped NWP accurately. 5. (UA) There are ambiguities regarding the segmentation of large-volume gray-scale CT data into pore-volumes suitable for pore-scale modeling. Simulated permeabilities vary by three orders of magnitude and do not resemble observed values very well. Small-volume synchrotron-based CT data (such as produced by OSU) does not suffer significantly from segmentation ambiguities. 6. (UA) A standard properly parameterized Shan-Chen model LB model is useful for simulating porous media with proxy fluids as well as the scCO2/brine system and produces results that are consistent with tomographic observations. 7. (UA) A LB model with fluid-interactions defined by a (modified) Peng-Robinson Equation of State is able to handle the scCO2/brine system with variable solid phase wettability. This model is numerically stable at temperatures between 0 and 250 °C and pressures between 3 and 50 MPa, and produces appropriate densities above the critical point of CO2 and exhibits three-phase separation below. Based on above findings OSU and UA have proposed continued experimentation and pore-scale modeling of the scCO2/brine system. The reported research has extensively covered capillary trapping using proxy fluids, but due to limited beam-time availability we were unable to apply our high-pressure CO2 setup to sufficient variation in fluid properties, and initial scCO2 connectivity. New data will also allow us to test, calibrate and apply our LB models to reservoir conditions beyond those that are currently feasible experimentally. Such experiments and simulations will also allow us to provide information how suitable proxy fluids are for the scCO2/brine system. We believe it would be worthwhile to pursue the following new research questions: 1. What are the fundamental differences in the physics underlying capillary trapping at ambient vs. supercritical conditions? 2. Do newly developed pore-scale trapping interactions and relationships translate to continuum scales? A motivation for these questions was elaborated in “Capillary Trapping of Super-Critical CO2: Linking Pore and Continuum Scales to Verify new Relationships” that was submitted to DOE-BES in 2015.

20 FOSSIL-FUELED POWER PLANTS↗

2012 Groundwater Monitoring Report Project Shoal Area Subsurface Corrective Action Unit 447

The Project Shoal Area (PSA) in Nevada was the site of a 12-kiloton underground nuclear test in 1963. Although the surface of the site has been remediated, investigation of groundwater contamination resulting from the test is still in the corrective action process. Annual sampling and hydraulic head monitoring are conducted at the site as part of the subsurface corrective action strategy. Analytical results from the 2012 monitoring are consistent with those of the previous years, with tritium detected only in well HC-4. The tritium concentration in groundwater from well HC-4 remains far below the U.S. Environmental Protection Agency-established maximum contaminant level of 20,000 picocuries per liter. Concentrations of total uranium and gross alpha were also detected during this monitoring period, with uranium accounting for nearly all the gross alpha activity. The total uranium concentrations obtained from this monitoring period were consistent with previous results and reflect a slightly elevated natural uranium concentration, consistent with the mineralized geologic terrain. Isotopic ratios of uranium also indicate a natural source of uranium in groundwater, as opposed to a nuclear-test-related source. Water level trends obtained from the 2012 water level data were consistent with those of previous years. The corrective action strategy for the PSA is currently focused on revising the site conceptual model (SCM) and evaluating the adequacy of the current monitoring well network. Some aspects of the SCM are known; however, two major concerns are the uncertainty in the groundwater flow direction and the cause of rising water levels in site wells west of the shear zone. Water levels have been rising in the site wells west of the shear zone since the first hydrologic characterization wells were installed in 1996. While water levels in wells west of the shear zone continue to rise, the rate of increase is less than in previous years. The SCM will be revised, and an evaluation of the groundwater monitoring network will be conducted when water levels at the site have stabilized.

54 ENVIRONMENTAL SCIENCES↗

Wellbore Seal Repair Using Nanocomposite Materials

Nanocomposite wellbore repair materials have been developed, tested, and modeled through an integrated program of laboratory testing and numerical modeling. Numerous polymer-cement nanocomposites were synthesized as candidate wellbore repair materials using various combinations of base polymers and nanoparticles. Based on tests of bond strength to steel and cement, ductility, stability, flowability, and penetrability in opening of 50 microns and less, we identified Novolac epoxy reinforced with multi-walled carbon nanotubes and/or alumina nanoparticles to be a superior wellbore seal material compared to conventional microfine cements. A system was developed for testing damaged and repaired wellbore specimens comprised of a cement sheath cast on a steel casing. The system allows independent application of confining pressures and casing pressures while gas flow is measured through the specimens along the wellbore axis. Repair with the nanocomposite epoxy base material was successful in dramatically reducing the flow through flaws of various sizes and types, and restoring the specimen comparable to an intact condition. In contrast, repair of damaged specimens with microfine cement was less effective, and the repair degraded with application of stress. Post-test observations confirm the complete penetration and sealing of flaws using the nanocomposite epoxy base material. A number of modeling efforts have supported the material development and testing efforts. We have modeled the steel-repair material interface behavior in detail during slant shear tests, which we used to characterize bond strength of candidate repair materials. A numerical model of the laboratory testing of damaged wellbore specimens was developed. This investigation found that microannulus permeability can satisfactorily be described by a joint model. Finally, a wellbore model has been developed that can be used to evaluate the response of the wellbore system (casing, cement, and microannulus), including the use of either cement or a nanocomposite in the microannulus to represent a repaired system. This wellbore model was successfully coupled with a field-scale model of CO 2 injection, to enable predictions of stress and strains in the wellbore subjected to subsurface changes (i.e. domal uplift) associated with fluid injection.

36 MATERIALS SCIENCE↗

Dissolution and reprecipitation of amorphous silica in silica Rich shales induces Non-Monotonic evolution of porosity in acidic reactive environments

Advances in sustainable subsurface energy technologies are crucial for meeting our energy and resource needs for a climate-resilient future. Novel strategies to harness subsurface shale reservoirs for recovering valuable metals and for enabling CO 2 storage are influenced by the morphological and mineralogical heterogeneities of these materials. In this context, delineating the interactions of highly acidic solutions such as wet supercritical CO 2 on shales with varying mineralogy is crucial to inform the stability of caprock seal for CO 2 storage and enhancements in permeability for fluid transport, reactivity, and storage. The feedback chemical effects associated with the interactions of acidic solutions on the morphologies and mineralogies of shales have not been extensively investigated. These insights are crucial for assessing temporal changes in the reactivity and the fate of the fluids in subsurface environments. In this study, we investigate the effect of 1M HCl solution on the chemistry and morphology of three different shale samples with varying carbonate, clay and silica contents. An increase in the amorphous content, from 37% to 41.3%, of silica-rich and carbonate/clay lean shale is noted due to reactions with an acidic solution which is attributed to the dissolution of Si-bearing phases such as clays, accompanied by SiO 2 precipitation. In shales bearing high content of clays and carbonates, significant increase in the pore volumes and surface areas are noted. Non-monotonic changes in the micron-scale porosity of silica rich–carbonate/clay lean (e.g., Mowry shale) are noted using in-situ X-ray microtomography experiments. Due to the initial mobilization of silica and dissolution of carbonate/clay phases, the total porosity slightly increases from 6.7% to 10.7% followed by a decrease to similar to 4% caused by SiO 2 reprecipitation. In conclusion, these findings suggest that even though silica is less reactive in acidic environments, the changes in the amorphous and crystalline content due to dissolution and reprecipitation alter the porosity and fluid flow paths.

04 OIL SHALES AND TAR SANDS↗

Multi-Scale Mass Transfer Processes Controlling Natural Attenuation and Engineered Remediation: An IFRC Focused on Hanford’s 300 Area Uranium Plume

The Integrated Field Research Challenge (IFRC) at the Hanford Site 300 Area uranium (U) plume addresses multi-scale mass transfer processes in a complex subsurface biogeochemical setting where groundwater and riverwater interact. A series of forefront science questions on reactive mass transfer motivates research. These questions relate to the effect of spatial heterogeneities; the importance of scale; coupled interactions between biogeochemical, hydrologic, and mass transfer processes; and measurements and approaches needed to characterize and model a mass-transfer dominated biogeochemical system. The project was initiated in February 2007, with CY 2007, CY 2008, CY 2009, and CY 2010 progress summarized in preceding reports. A project peer review was held in March 2010, and the IFRC project acted upon all suggestions and recommendations made in consequence by reviewers and SBR/DOE. These responses have included the development of 'Modeling' and 'Well-Field Mitigation' plans that are now posted on the Hanford IFRC web-site, and modifications to the IFRC well-field completed in CY 2011. The site has 35 instrumented wells, and an extensive monitoring system. It includes a deep borehole for microbiologic and biogeochemical research that sampled the entire thickness of the unconfined 300 A aquifer. Significant, impactful progress has been made in CY 2011 including: (i) well modifications to eliminate well-bore flows, (ii) hydrologic testing of the modified well-field and upper aquifer, (iii) geophysical monitoring of winter precipitation infiltration through the U-contaminated vadose zone and spring river water intrusion to the IFRC, (iv) injection experimentation to probe the lower vadose zone and to evaluate the transport behavior of high U concentrations, (v) extended passive monitoring during the period of water table rise and fall, and (vi) collaborative down-hole experimentation with the PNNL SFA on the biogeochemistry of the 300 A Hanford-Ringold contact and the underlying redox transition zone. The modified well-field has functioned superbly without any evidence for well-bore flows. Beyond these experimental efforts, our site-wide reactive transport models (PFLOTRAN and eSTOMP) have been updated to include site geostatistical models of both hydrologic properties and adsorbed U distribution; and new hydrologic characterization measurements of the upper aquifer. These increasingly robust models are being used to simulate past and recent U desorption-adsorption experiments performed under different hydrologic conditions, and heuristic modeling to understand the complex functioning of the smear zone. We continued efforts to assimilate geophysical logging and 3D ERT characterization data into our site wide geophysical model, with significant and positive progress in 2011 that will enable publication in 2012. Our increasingly comprehensive field experimental results and robust reactive transport simulators, along with the field and laboratory characterization, are leading to a new conceptual model of U(VI) flow and transport in the IFRC footprint and the 300 Area in general, and insights on the microbiological community and associated biogeochemical processes influencing N, S, C, Mn, and Fe. Collectively these findings and higher scale models are providing a unique and unparalleled system-scale understanding of the biogeochemical function of the groundwater-river interaction zone.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

2012 Groundwater Monitoring Report Central Nevada Test Area, Subsurface Corrective Action Unit 443

The Central Nevada Test Area was the site of a 0.2- to 1-megaton underground nuclear test in 1968. The surface of the site has been closed, but the subsurface is still in the corrective action process. The corrective action alternative selected for the site was monitoring with institutional controls. Annual sampling and hydraulic head monitoring are conducted as part of the subsurface corrective action strategy. The site is currently in the fourth year of the 5-year proof-of-concept period that is intended to validate the compliance boundary. Analytical results from the 2012 monitoring are consistent with those of previous years. Tritium remains at levels below the laboratory minimum detectable concentration in all wells in the monitoring network. Samples collected from reentry well UC-1-P-2SR, which is not in the monitoring network but was sampled as part of supplemental activities conducted during the 2012 monitoring, indicate concentrations of tritium that are consistent with previous sampling results. This well was drilled into the chimney shortly after the detonation, and water levels continue to rise, demonstrating the very low permeability of the volcanic rocks. Water level data from new wells MV-4 and MV-5 and recompleted well HTH-1RC indicate that hydraulic heads are still recovering from installation and testing. Data from wells MV-4 and MV-5 also indicate that head levels have not yet recovered from the 2011 sampling event during which several thousand gallons of water were purged. It has been recommended that a low-flow sampling method be adopted for these wells to allow head levels to recover to steady-state conditions. Despite the lack of steady-state groundwater conditions, hydraulic head data collected from alluvial wells installed in 2009 continue to support the conceptual model that the southeast-bounding graben fault acts as a barrier to groundwater flow at the site.

54 ENVIRONMENTAL SCIENCES↗

The ParFlow Sandtank: An interactive educational tool making invisible groundwater visible

Physical aquifer models are a highly effective teaching tool for hydrology education, however they come with inherent limitations that include the high cost to purchase, the static configuration of the model materials, the time required to visualize hydrogeological phenomena, and the effort to reset and clean them over time. To address these and other limitations, we have developed an interactive computer simulation of a physical aquifer model called the ParFlow Sandtank. In this gamified interface, users run the simulation using a familiar web-app like interface with sliders and buttons while learning real hydrologic concepts. Our user interface allows participants to dive into the world of hydrology, understanding assumptions about model parameters such as hydraulic conductivity, making decisions about inputs to groundwater aquifer systems such as pumping rates, visualizing outputs such as stream flow, transport, and saturation, and exploring various factors that impact real environmental systems such as climate change. The ParFlow Sandtank has already been used in a variety of educational settings with more than 9,000 users per year, and we feel this emerging educational tool can be used broadly in educational environments and can be scaled-up to provide greater accessibility for students and educators. Here we present the capabilities and workflow of the ParFlow Sandtank, two use cases, and additional tools and custom templates that have been developed to support and enhance the reach of the ParFlow Sandtank.

54 ENVIRONMENTAL SCIENCES↗

Flexible Geothermal Power Generation utilizing Geologic Thermal Energy Storage (Final Seedling Project Report)

This report concludes that there is a cost-effective strategy for seasonal storage of heat that will provide firm, but dispatchable, electrical generating capacity in times when other renewable energy is not available to meet demand. Deployment of the technology appears to require no new technology, but instead combines solar, geothermal, and conventional oil and gas drilling technologies in a novel way. The study basis is the use of sedimentary geologic formations as a medium for thermal energy storage (TES), specifically for heat collected in concentrating solar collectors. The study identifies methodologies that could be used to transport this heat into and out of the subsurface in order to produce dispatchable electrical power, and reports on initial optimization results. The GeoTES system (heat input, storage, heat recovery, and heat to electric conversion) described in this analysis has the potential to provide a unique pathway for increasing the grid penetration of renewable energy in large blocks of power and across many states and regions. Further, the system can be used both to meet the nation’s flexible energy needs while also improving grid stability and reliability. The present study evaluated the use of a large number of dedicated wells to store and recover the heat, essentially creating a synthetic geothermal reservoir. The use of sedimentary geology allows the wells to be drilled at low cost. Dedicated hot and cold wells are used, arranged in a five-spot well pattern with each hot or cold well surrounded at an appropriate distance by the opposite type of well. In large numbers this becomes alternating rows of hot and cold wells. Each hot and cold well is operated using a push-pull strategy. This configuration provides the ability to immediately recover stored hot fluid from a GeoTES reservoir, or to store the heat over many months for recovery at low loss when needed. This is a practical approach for managing the system’s fluid inventory and reducing parasitic load. The production and injection power requirements are reduced because the rows of wells operating in “push” mode provide help to the wells operating in “pull” mode, and vice-versa. Initial charging of a GeoTES system increases the heat recovery temperature. Increasing the duration of the charging period decreases the magnitude of the temperature fluctuations that occur following prolonged system operation. Because of direct contact of the heated water with the reservoir formation, the production of both hot water and steam from the TES, and the temperature ranges of the recovered fluid (190 – 230°C or 375 – 445°F), conventional geothermal power cycles were used to convert the stored heat to electricity. A power cycle configuration for the GeoTES system was selected following a screening study of a number of flash, and flash/binary hybrid options. This analysis concluded that, of the configurations evaluated, a dual-stage flash steam cycle provides the lowest capital costs per unit net power generation with an acceptable hot brine inlet fluid flow rate. The evaluation included the power plant cost estimate, the cost and number of wells and the associated parasitic loads. Annual power generation performance was simulated to evaluate capacity factor and LCOE. The LCOE calculated for the inherently high capacity GeoTES system was $\$$0.13/kWhe. This value was calculated for the case where the solar thermal collector was sized in such a way that the solar collectors permitted an annual power plant capacity factor of up to 97%. The power cycle was able to provide power to the grid every night of the year, and flexible base-load power during the winter, if needed. This LCOE value compares favorably with reported values for solar photovoltaic plus battery energy storage (PV+BES) systems in the open literature, i.e. $\$$0.148/kWhe for a PV+BES system with 4 hours of electrochemical battery energy storage capacity. Addition of battery energy storage with more hours of storage would further increase PV+BES system LCOE and increase the separation between GeoTES and PV+BES. A GeoTES system would therefore provide superior economics for high capacity and long duration solar energy storage.

14 SOLAR ENERGY↗

Changes in the pore network structure of Hanford sediment after reaction with caustic tank wastes

At the former nuclear weapon production site in Hanford, WA, caustic radioactive tank waste leaks into subsurface sediments and causes dissolution of quartz and aluminosilicate minerals, and precipitation of sodalite and cancrinite. This work examines changes in pore structure due to these reactions in a previously-conducted column experiment. The column was sectioned and 2D images of the pore space were generated using backscattered electron microscopy and energy dispersive X-ray spectroscopy. A pre-precipitation scenario was created by digitally removing mineral matter identified as secondary precipitates. Porosity, determined by segmenting the images to distinguish pore space from mineral matter, was up to 0.11 less after reaction. Erosion-dilation analysis was used to compute pore and throat size distributions. Images with precipitation had more small and fewer large pores. Precipitation decreased throat sizes and the abundance of large throats. These findings agree with previous findings based on 3D X-ray CMT imaging, observing decreased porosity, clogging of small throats, and little change in large throats. However, 2D imaging found an increase in small pores, mainly in intragranular regions or below the resolution of the 3D images. Also, an increase in large pores observed via 3D imaging was not observed in the 2D analysis. Changes in flow conducting throats that are the key permeability-controlling features were observed in both methods.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Progress in Simulated Water Well Performance on Mars

Recent studies of human Mars missions considered the impacts of an abundant supply of in-situ, accessible water on these mission scenarios. Discovery of exposed water ice scarps in Martian mid-latitudes has bolstered the evidence for massive amounts of almost pure water in buried deposits in regions considered candidates for these future human missions. This paper describes progress towards adapting a long-standing terrestrial technique for accessing and extracting water from these mid-latitude sources of ice. This approach relies on mechanical drills to access the ice through overlying debris. Once the ice layer has been reached, a technique known as a Rodriguez Well, or Rodwell, is used to melt the ice, store the resulting water in a subsurface cavity until needed, and then pump the water to the surface for use. Previous work by the authors utilized a computer simulation to predict the performance of a Martian Rodwell. This simulation was originally developed to predict performance in terrestrial Polar Regions. Whereas the basic approach is appropriate for a similar well on Mars, several parameters had been empirically derived and required experiments simulating the Martian environment to determine the values appropriate for a Martian Rodwell simulation. These experiments have now been completed and preliminary values have been determined for the empirical parameters. Test results are consistent with a dimensionless Sh(Ra) correlation developed by Bower and Saylor (2009) and based on lab tests of water evaporating from a pool into a large air chamber. They are also consistent with correlations derived by Ingersoll (1970) and by Hecht (2002), based on natural-convection heat transfer. Each of these earlier correlations found Sh~Ra1/3, with the 1/3rd power characteristic of large Ra where the boundary layer over the pool surface is turbulent. A somewhat surprising result was that this power-law was found to extend into a range of Ra where laminar flow would be expected. Another surprising result was found in that instead of following established correlations for natural-convection heat transfer over flat plates, the dimensionless heat-transfer rates (Nu) were much larger and approximately independent of Ra. This suggests that mass transfer from the pool enhances convective heat transfer, possibly by enhanced mixing in the boundary layer. Although this possibility has been suggested in the literature, if it is proven to be true under these conditions it could play an important role in the use of a Rodwell on Mars, where evaporative mass transfer is enhanced relative to terrestrial wells.

Human Mars Mission↗

Multiscale Characterization of Structural Compositional and Textural Heterogeneity of Nano-porous Geomaterials

The purpose of the project was to perform multiscale characterization of low permeability rocks to determine the effect of physical and chemical heterogeneity on the poromechanical and flow responses of shales and carbonate rocks with a broad range of physical and chemical heterogeneity . An integrated multiscale imaging of shale and carbonate rocks from nanometer to centimeter scales include s dual focused ion beam - scanning electron microscopy (FIB - SEM) , micro computed tomography (micro - CT) , optical and confocal microscopy, and 2D and 3D energy dispersive spectroscopy (EDS). In addition, mineralogical mapping and backscattered imaging with nanoindentation testing advanced the quantitative evaluat ion of the relationship between material heterogeneity and mechanical behavior. T he spatial distribution of compositional heterogeneity, anisotropic bedding patterns, and mechanical anisotropy were employed as inputs for brittle fracture simulations using a phase field model . Comparison of experimental and numerical simulations reveal ed that proper incorporation of additional material information, such as bedding layer thickness and other geometrical attributes of the microstructures, can yield improvements on the numerical prediction of the mesoscale fracture patterns and hence the macroscopic effective toughness. Overall, a comprehensive framework to evaluate the relationship between mechanical response and micro-lithofacial features can allow us to make more accurate prediction of reservoir performance by developing a multi - scale understanding of poromechanical response to coupled chemical and mechanical interactions for subsurface energy related activities.

36 MATERIALS SCIENCE↗

Entropic Control of HD Exchange Rates over Dilute Pd-in-Au Alloy Nanoparticle Catalysts

Dilute Pd-in-Au alloy catalysts are promising materials for selective hydrogenation catalysis. Extensive surface science studies have contributed mechanistic insight on the energetic aspect of hydrogen dissociation, migration and recombination on dilute alloy systems. Yet, translating these fundamental concepts to the kinetics and free energy of hydrogen dissociation on nanoparticle catalysts operating at ambient pressures and temperatures remains challenging. Here, the effect of the Pd concentration and Pd ensemble size on the catalytic activity, apparent activation energy and rate limiting process is addressed by combining experiment and theory. Experiments in a flow reactor show that a compositional change from 4 to 8 atm% Pd of the Pd-in-Au alloy catalyst leads to strong increase in activity, even exceeding the activity per Pd atom of monometallic Pd under the same conditions, albeit with an increase in apparent activation energy. First-principles calculations show that the rate and apparent activation enthalpy for HD exchange increase when increasing the Pd ensemble size from single Pd atoms to Pd trimers in a Au surface, suggesting that the ensemble size distribution shifts from mainly single Pd atoms on the 4 atm% Pd alloy to larger Pd ensembles of at least three atoms for the 8 atm% Pd/Au catalyst. The DFT studies also indicated that the rate-controlling process is different: H 2 (D 2 ) dissociation determines the rate for single atoms whereas recombination of adsorbed H and D determines the rate on Pd trimers. Both experiment and theory suggest that the increased reaction rate with increasing Pd content and ensemble size stems from an entropic driving force. Lastly, our results support hydrogen migration between Pd sites via Au and indicate that the dilute alloy design prevents the formation of subsurface hydrogen, which is crucial in achieving high selectivity in hydrogenation catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multi-Scale Mass Transfer Processes Controlling Natural Attenuation and Engineered Remediation: An IFRC Focused on Hanford’s 300 Area Uranium Plume

The Integrated Field-Scale Subsurface Research Challenge (IFRC) at the Hanford Site 300 Area uranium (U) plume addresses multi-scale mass transfer processes in a complex hydrogeologic setting where groundwater and riverwater interact. A series of forefront science questions on mass transfer are posed for research which relate to the effect of spatial heterogeneities; the importance of scale; coupled interactions between biogeochemical, hydrologic, and mass transfer processes; and measurements and approaches needed to characterize and model a mass-transfer dominated system. The project was initiated in February 2007, with CY 2007 and CY 2008 progress summarized in preceding reports. The site has 35 instrumented wells, and an extensive monitoring system. It includes a deep borehole for microbiologic and biogeochemical research that sampled the entire thickness of the unconfined 300 A aquifer. Significant, impactful progress has been made in CY 2009 with completion of extensive laboratory measurements on field sediments, field hydrologic and geophysical characterization, four field experiments, and modeling. The laboratory characterization results are being subjected to geostatistical analyses to develop spatial heterogeneity models of U concentration and chemical, physical, and hydrologic properties needed for reactive transport modeling. The field experiments focused on: (1) physical characterization of the groundwater flow field during a period of stable hydrologic conditions in early spring, (2) comprehensive groundwater monitoring during spring to characterize the release of U(VI) from the lower vadose zone to the aquifer during water table rise and fall, (3) dynamic geophysical monitoring of salt-plume migration during summer, and (4) a U reactive tracer experiment (desorption) during the fall. Geophysical characterization of the well field was completed using the down-well Electrical Resistance Tomography (ERT) array, with results subjected to robust, geostatistically constrained inversion analyses. These measurements along with hydrologic characterization have yielded 3D distributions of hydraulic properties that have been incorporated into an updated and increasingly robust hydrologic model. Based on significant findings from the microbiologic characterization of deep borehole sediments in CY 2008, down-hole biogeochemistry studies were initiated where colonization substrates and spatially discrete water and gas samplers were deployed to select wells. The increasingly comprehensive field experimental results, along with the field and laboratory characterization, are leading to a new conceptual model of U(VI) flow and transport in the IFRC footprint and the 300 Area in general, and insights on the microbiological community and associated biogeochemical processes. A significant issue related to vertical flow in the IFRC wells was identified and evaluated during the spring and fall field experimental campaigns. Both upward and downward flows were observed in response to dynamic Columbia River stage. The vertical flows are caused by the interaction of pressure gradients with our heterogeneous hydraulic conductivity field. These impacts are being evaluated with additional modeling and field activities to facilitate interpretation and mitigation. The project moves into CY 2010 with ambitious plans for a drilling additional wells for the IFRC well field, additional experiments, and modeling. This research is part of the ERSP Hanford IFRC at Pacific Northwest National Laboratory.

54 ENVIRONMENTAL SCIENCES↗