Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRPLANES - STRENGTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

General Theory of the Steady Motion of an Airplane

The writer points out briefly the history of the method proposed for the study of steady motion of an airplane, which is different from other methods now used. M. Paul Painleve has shown how convenient the drag-lift curve was for the study of airplane steady motion. The author later added to the drift-lift curve the curve called the "speed curve" which permits a direct checking of the speed of the airplane under all flying conditions. But the speed curve was plotted in the same quadrant as the drag-lift curve. Later, with the progressive development of aeronautical science, and with the continually increasing knowledge concerning engines and propellers, the author was brought to add the three other quadrants to the original quadrant, and thus was obtained the steady motion chart which is described in detail in this report. This charts permits one to read directly for a given airplane its horizontal speed at any altitude, its rate of climb at any altitude, its apparent inclination to the horizon at any moment, its ceiling, its propeller thrust, revolutions, efficiency, and power absorbed, that is the complete set of quantities involved in the subject, and to follow the variations of all these quantities both for variable altitude and for variable throttle. The chart also permits one to follow the variation of all of the above in flight as a function of the lift coefficient and of the speed. The author also discusses the interaction of the airplane and propeller through the slipstream and the question of the properties of the engine-propeller system and its dependence upon the properties of the engine considered alone and of the propeller considered alone. There is also a discussion of a standard atmosphere.

De Bothezat, George↗

Maneuverability Investigation of the F6C-3 Airplane with Special Flight Instruments

This investigation was made for the purpose of obtaining information on the maneuverability of the F6C-3 airplane. It is the first of a series of similar investigations to be conducted on a number of military airplanes for the purpose of comparing the abilities of these airplanes to maneuver, and also to establish a fund of quantitative data which may be used in formulating standards of comparison for rating the maneuverability of any airplane. A large part of this initial investigation was necessarily devoted to the development and trial of methods suitable for use in subsequent investigations of this nature. Air speed, angular velocity, linear acceleration, and position of the control surfaces were measured by instruments in the airplane during loops, push-downs, pull-outs from dives, pull-ups from level flight, barrel rolls, and spins. The coordinates of flight paths were deduced from the data whenever possible, and were checked in some cases by the use of a camera obscura. The results are given in curves showing the variation of the measured quantities with respect to time, and maximum values are tabulated.

Dearborn, C H↗

An analysis of the stability of an airplane with free controls

Report presents the results of an investigation made of the essentials to the stability of an airplane with free control surfaces. Calculations are based on typical airplane characteristics with certain factors varied to cover a range of current designs. Stability charts are included to show the limiting values of the aerodynamic hinge moments and the weight hinge moments of the control surfaces for various positions of the center of gravity of the airplane and for control systems with various moments of inertia. The effects of reducing the chord and of eliminating the floating tendency of the surface, of changing the wing loading, and of decreasing the radius of gyration of the airplane are also indicated. An investigation has also been made of the nature of the motion of the airplane with controls free and of the modes of instability that may occur.

Jones, Robert T↗

A theoretical analysis of the effect of time lag in an automatic stabilization system on the lateral oscillatory stability of an airplane

A method is presented for determining the effect of time lag in an automatic stabilization system on the lateral oscillatory stability of an airplane. The method is based on an analytical-graphical procedure. The critical time lag of the airplane-autopilot system is readily determined from the frequency-response analysis. The method is applied to a typical present-day airplane equipped with an automatic pilot sensitive to yawing acceleration and geared to the rudder so that rudder control is applied in proportion to the yawing acceleration. The results calculated for this airplane-autopilot system by this method are compared with the airplane motions calculated by a step-by-step procedure.

Sternfield, Leonard↗

Airplane takeoff and landing performance monitoring system

The invention is a real-time takeoff and landing performance monitoring system for an aircraft which provides a pilot with graphic and metric information to assist in decisions related to achieving rotation speed (VR) within the safe zone of a runway, or stopping the aircraft on the runway after landing or take-off abort. The system processes information in two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data. The real-time segment uses the scheduled performance data, runway length data and transducer measured parameters to monitor the performance of the airplane throughout the takeoff roll. Airplane acceleration and engine-performance anomalies are detected and annunciated. A novel and important feature of this segment is that it updates the estimated runway rolling friction coefficient. Airplane performance predictions also reflect changes in head wind occurring as the takeoff roll progresses. The system provides a head-down display and a head-up display. The head-up display is projected onto a partially reflective transparent surface through which the pilot views the runway. By comparing the present performance of the airplane with a continually predicted nominal performance based upon given conditions, performance deficiencies are detected by the system and conveyed to pilot in form of both elemental information and integrated information.

Middleton, David B.↗

Generic Airplane Model Concept and Four Specific Models Developed for Use in Piloted Simulation Studies

A generic airplane model concept was developed to allow configurations with various agility, performance, handling qualities, and pilot vehicle interface to be generated rapidly for piloted simulation studies. The simple concept allows stick shaping and various stick command types or modes to drive an airplane with both linear and nonlinear components. Output from the stick shaping goes to linear models or a series of linear models that can represent an entire flight envelope. The generic model also has provisions for control power limitations, a nonlinear feature. Therefore, departures from controlled flight are possible. Note that only loss of control is modeled, the generic airplane does not accurately model post departure phenomenon. The model concept is presented herein, along with four example airplanes. Agility was varied across the four example airplanes without altering specific excess energy or significantly altering handling qualities. A new feedback scheme to provide angle-of-attack cueing to the pilot, while using a pitch rate command system, was implemented and tested.

Hoffler, Keith D.↗

A Method for Integrating Thrust-Vectoring and Actuated Forebody Strakes with Conventional Aerodynamic Controls on a High-Performance Fighter Airplane

A method, called pseudo controls, of integrating several airplane controls to achieve cooperative operation is presented. The method eliminates conflicting control motions, minimizes the number of feedback control gains, and reduces the complication of feedback gain schedules. The method is applied to the lateral/directional controls of a modified high-performance airplane. The airplane has a conventional set of aerodynamic controls, an experimental set of thrust-vectoring controls, and an experimental set of actuated forebody strakes. The experimental controls give the airplane additional control power for enhanced stability and maneuvering capabilities while flying over an expanded envelope, especially at high angles of attack. The flight controls are scheduled to generate independent body-axis control moments. These control moments are coordinated to produce stability-axis angular accelerations. Inertial coupling moments are compensated. Thrust-vectoring controls are engaged according to their effectiveness relative to that of the aerodynamic controls. Vane-relief logic removes steady and slowly varying commands from the thrust-vectoring controls to alleviate heating of the thrust turning devices. The actuated forebody strakes are engaged at high angles of attack. This report presents the forward-loop elements of a flight control system that positions the flight controls according to the desired stability-axis accelerations. This report does not include the generation of the required angular acceleration commands by means of pilot controls or the feedback of sensed airplane motions.

Lallman, Frederick J.↗

A Parametric Study of Accelerations of an Airplane Due to a Wake Vortex System

A study was conducted using strip theory to systematically investigate the effects of progressively more complete descriptions of the interaction of an airplane with a wake vortex system. The emphasis was in roll-dominant, parallel, vortex encounters. That is, the simulated airplane's longitudinal axis was nearly parallel to the rotation axis of the vortex system for most of the results presented. The study began with a drag-less rectangular wing in the flow field of a single vortex and progressed to a complete airplane with aerodynamic surfaces possessing taper, sweep, dihedral, and stalling and immersed in the flow field of a vortex pair in ground effect. The effects of the pitch, roll, and yaw attitudes of the airplane on the calculated accelerations were also investigated. The airplane had the nominal characteristics of a Boeing 757, and the vortex flow field had the nominal characteristics of the wake of a Boeing 767. The Bumham-Hallock model of a vortex flow field was used throughout the study. The data are presented mainly in terms of contours of equal acceleration in a two-dimensional area centered on the vortex pair and having dimensions of 300 feet by 300 feet.

Stewart, Eric C.↗

Calculated Drag of an Aerial Refueling Assembly Through Airplane Performance Analysis

The aerodynamic drag of an aerial refueling assembly was calculated during the Automated Aerial Refueling project at the NASA Dryden Flight Research Center. An F/A-18A airplane was specially instrumented to obtain accurate fuel flow measurements and to determine engine thrust. A standard Navy air refueling store with a retractable refueling hose and paradrogue was mounted to the centerline pylon of the F/A-18A airplane. As the paradrogue assembly was deployed and stowed, changes in the calculated thrust of the airplane occurred and were equated to changes in vehicle drag. These drag changes were attributable to the drag of the paradrogue assembly. The drag of the paradrogue assembly was determined to range from 200 to 450 lbf at airspeeds from 170 to 250 KIAS. Analysis of the drag data resulted in a single drag coefficient of 0.0056 for the paradrogue assembly that adequately matched the calculated drag for all flight conditions. The drag relief provided to the tanker airplane when a receiver airplane engaged the paradrogue is also documented from 35 to 270 lbf at the various flight conditions tested. The results support the development of accurate aerodynamic models to be used in refueling simulations and control laws for fully autonomous refueling.

Vachon, Michael Jacob↗

Application of Monte Carlo Technique for Determining Maneuvering Loads from Statistical Information on Airplane Motions

Results of a statistical analysis of horizontal-tail loads on a fighter airplane are presented. The data were obtained from a number of operational training missions with flight at altitudes up to about 50,000 feet and at Mach numbers up to 1.22. The analysis was performed to determine the feasibility of calculating horizontal-tail load from data on the flight conditions and airplane motions. In the analysis the calculated loads are compared with the measured loads for the different types of missions performed. The loads were calculated by two methods: a direct approach and a Monte Carlo technique. The procedures used and some of the problems associated with the data analysis are discussed. frequencies of occurrence of tail loads of given magnitudes are derived from statistical information on the flight quantities. In the direct method, a time history of tail load is calculated from time-history measurements of the flight quantities. The Monte Carlo method could be useful for extending loads information for design of prospective airplanes . For the Monte Carlo method, the The results indicate that the accuracy of loads, regardless of the method used for calculation, is largely dependent on the knowledge of the pertinent airplane aerodynamic characteristics and center-of-gravity location. In addition, reliable Monte Carlo results require an adequate sample of statistical data and a knowledge of the more important statistical dependencies between the various flight conditions and airplane motions.

Hamer, Harold A.↗

Ditching Tests with a 1/16-Size Model of the Navy XP2V-1 Airplane at the Langley Tank No. 2 Monorail

Tests were made with a 1/16 size dynamically similar model of the Navy XP2V-1 airplane to study its performance when ditched. The model was ditched in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds, and conditions of damage were simulated. The performance of the node1 was determined and recorded from visual observations, by recording time histories of the longitudinal decelerations, and by taking motion pictures of the ditchings From the results of the tests with the model the following conclusions were drawn: 1. The airplane should be ditched at the normal landing attitude. The flaps should be fully extended to obtain the lowest possible landing speed; 2. Extensive damage will occur in a ditching and the airplane probably will dive violently after a run of about 2 fuselage lengths. Maximum longitudinal decelerations up to about 4g will be encountered; and 3. If a trapezoidal hydroflap 4 feet by 2 feet by 1 foot is attached to the airplane at station 192.4, diving will be prevented and the airplane will probably porpoise in a run of about 4 fuselage lengths with a maximum longitudinal deceleration of less than 3.5g.

Fisher, Lloyd J.↗

Gust-Tunnel Investigation to Determine the Load at the Joint of a Coupled Airplane Configuration Encountering a Gust

An investigation has been made in the Langley gust tunnel with two identical airplane models approximating 1/40-scale models of the B-29, coupled in tandem with a boom so that the individual centers of gravity were equidistant from the single coupling joint at the tail of the lead airplane. Time histories of the boom joint load were obtained as the models were flown through a gust. The results indicate that on a similar configuration involving airplanes the size of B-29 airplanes a load on the boom joint of 10,000 to 14,000 pounds could be induced by encountering a gust of 50 feet per second and having a gradient distance of 17 chords, at a forward speed of 380 feet per second and that the total load is extremely sensitive to the steadiness of flight that can be maintained with or without a gust. It is felt that the results are probably satisfactory to show order of magnitude, but it does not appear possible that a precise determination of the joint load that would be applicable to the full-scale airplanes can be obtained by gust-tunnel tests.

Cahen, George L.↗

Directional Stability of Towed Airplanes

So far, very careful investigations have been made regarding the flight properties, in particular the static and dynamic stability, of engine-propelled aircraft and of untowed gliders. In contrast, almost no investigations exist regarding the stability of airplanes towed by a towline. Thus, the following report will aim at investigating the directional stability of the towed airplane and, particularly, at determining what parameters of the flight attitude and what configuration properties affect the stability. The most important parameters of the flight attitude are the dynamic pressure, the aerodynamic coefficients of the flight attitude, and the climbing angle. Among the configuration properties, the following exert the greatest influence on the stability: the tow-cable length, the tow-cable attachment point, the ratio of the wing loadings of the towing and the towed airplanes, the moments of inertia, and the wing dihedral of the towed airplane. In addition, the size and shape of the towed airplane vertical tail, the vertical tail length, and the fuselage configuration are decisive factors in determining the yawing moment and side force due to sideslip, respectively.

Soehne, W.↗

Aerodynamic Characteristics of a 0.04956-Scale Model of the Convair TF-102A Airplane at Transonic Speeds, Coord. No. AF-120

The basic aerodynamic characteristics of a 0.04956-scale model of the Convair TF-102A airplane with controls undeflected have been determined at Mach numbers from 0.60 to 1.135 for angles of attack up to approximately 22 deg in the Langley 8-foot transonic tunnel. In addition, comparisons have been made with data obtained from a previous investigation of a 0.04956-scale model of the Convair F-102A airplane. The results indicated the TF-102A airplane was longitudinally stable for all conditions tested. An increase in lift-curve slope from 0.045 to 0.059 and an 11-percent rearward shift in aerodynamic-center location occurred with increases in Mach number from 0.60 to approximately 1.05. The zero-lift drag coefficient for the TF-102A airplane increased 145 percent between the Mach numbers of 0.85 and 1.075; the maximum lift-drag ratio decreased from 9.5 at a Mach number of 0.60 to 5.0 at Mach numbers above 1.025. There was little difference in the lift and pitching-moment characteristics and drag due to life between the TF-102A and F-102A configurations. However, as compared with the F-102A airplane, the zero-lift drag-rise Mach number for the TF-102A was reduced by at least 0.06, the zero-lift peak wave drag was increased 50 percent, and the maximum lift-drag ratio was reduced as much as 20 percent.

Osborne, Robert S.↗

Concluding Report on Free-Spinning and Recovery Characteristics of a 1/24-Scale Model of the Grumman F11F-1 Airplane, TED No. NACA AD 395

An investigation has been completed in the Langley 20-foot free-spinning tunnel on a l/24-scale model of the Grumman F11F-1 airplane to determine its spin and recovery characteristics. An interim report, Research Memorandum SL55G20, was published earlier and the present report concludes the presentation of results of the investigation. Primarily, the present report presents results obtained with engine gyroscopic moments simulated on the model. Also, the current results were obtained with a revised larger vertical tail recently incorporated on the airplane. It was difficult to obtain developed spins on the model when the spin direction was in the same sense as that of the engine rotation (right spin on the airplane). The developed spins obtained were very oscillatory and the recoveries were unsatisfactory. These results were similar to those previously reported for which engine rotation was not simulated. When the spin direction was in the opposite sense (left spin on the airplane), however, developed spins were readily obtainable. Recoveries from these spins also were unsatisfactory. Satisfactory recoveries were obtained on the model, however, when rudder reversal was accompanied by extension of small canards near the nose of the airplane or by deflection of the horizontal tail differentially with the spin.

Bowman, James S., Jr.↗

Free-Spinning-Tunnel Tests of a 1/27-Scale Model of the Douglas XF3D-1 Airplane, TED No. NACA DE 312

Free-spinning-tunnel tests have been made on a 1/27-scale model of the Douglas XF3D-1 airplane to confirm a preliminary evaluation made of the airplane spin and recovery characteristics and previously reported. Recovery characteristics were satisfactory for erect and inverted spins when the model was in the clean condition. When the slow-down brakes were open, recoveries were slow. The pedal force necessary to reverse the airplane rudder during a spin will be within the physical capabilities of the pilot. A 10-foot-diameter parachute attached to the tail of the airplane (laid-out-flat diameter, drag coefficient 0.7) or a 4.5-foot-diameter parachute attached to the outboard wing tip will be satisfactory for emergency spin recovery from demonstration spins. If it becomes necessary for the crew to abandon the airplane during a spin, they should leave from the outboard side of the cockpit. The test results indicated spin and recovery characteristics generally similar to those indicated in the preliminary evaluation.

Scher, Stanley H.↗

Ditching Tests of a 1/20-Scale Model of the Northrop B-35 Airplane

Tests of a 1/20-scale dynamically similar model of the Northrop B-35 airplane were made to study its ditching characteristics. The model was ditched in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds,and conditions of damage were simulated during the investigation. The ditching characteristics were determined by visual observation and from motion-picture records and time-history acceleration records. Both longitudinal and lateral accelerations were measured. Results are given in tabular form and time-history acceleration curves and sequence photographs are presented. Conclusions based on the model investigation are as follows: 1. The best ditching of the B-35 airplane probably can be made by contacting the water in a near normal landing attitude of about 9 deg with the landing flaps full down so as to have a low horizontal speed. 2. The airplane usually will turn or yaw but the motion will not be violent. The maximum lateral acceleration will be about 2g. 3. If the airplane does not turn or yaw immediately after landing, it probably will trim up and then make a smooth run or porpoise slightly. The maximum longitudinal decelerations that will be encountered are about 6g or 7g. 4. Although the decelerations are not indicated to be especially large, the construction of the airplane is such that extensive damage is to be expected, and it probably will be difficult to find ditching stations where crew members can adequately brace themselves and be reasonably sure of avoiding a large inrush of water.

Fisher, Lloyd J.↗

Spin Tests of 1/20-Scale Models of the Chance Vought Revised XF6U-1 and F6U-1 Airplanes, TED No. NACA 2390

An investigation has been conducted in the Langley 20-foot free-spinning tunnel on the 1/20-scale model of the Chance Vought XF6U-1 airplane altered to represent the XF6U-1 airplane as it will be spin-tested in flight, and also altered to represent the F6U-1 airplane as it will be produced for service use. Spin tests were made to determine the effects of control settings and movements at the normal loading. The results show that the spins obtained on the revised XF6U-1 airplane will be oscillatory in roll and yaw and that recoveries by rudder reversal will be rapid. Model test results indicate that the F6U-1 airplane will probably not spin. Inasmuch as the results of this investigation show that the new designs are as good as or better than the original XF6U-1 design in regard to spin recovery, it is felt that the conclusions and recommendations reached for the original design can be applied to the new designs for all loading conditions.

Klinar, Walter J.↗