Adaptively Switching Gradient Descent for Reliable PINN Training with Guarantees
Explore the source record for details and available documents.
Accelerator Design, Technology, and Operations↗
SEARCH · Search NASA
Results for “Accelerator Design”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Preliminary Look at the LBEG & MPEG Beam Transmissions between HPSim and Operation Data
This report summarizes recent work on estimating the transmission of LANSCE H- beams from the end of the present DTL to both the PSR stripper foil (LBEG) and WNR target 4 (MPEG). The LBEG beam might be considered a more typical LINAC beam and lends itself to continuous monitoring of transmission through the various stages of the accelerator. For the MPEG, however, the widely-spaced micropulses and lack of the requisite sensitivity current monitors throughout the accelerator make these measurements extremely difficult and more uncertain. Therefore, to assist in estimating the MPEG beam transmission, beam-dynamics simulations using HPSim were employed. These beam transmission estimates from the end of the Drift Tube Linac (DTL) to Target 4 (MPEG) and the PSR stripper foil (LBEG) are vital to determine the charge requirements for LAMP’s front end. In this technote, we demonstrate three major efforts in determining the transmission: (1) Convert the WNR beamline lattice from TRANSPORT to HPSim for use in the simulation; (2) Simulate the optimization process in the Central Control Room (CCR) that brings down the losses by up to a factor of 4000 between the end of the initial physics-based tuneup phase and production beam operation; (3) Analyze operational data to deduce measured transmissions. Table 1 shows the estimated losses with HPSim and operational analysis. Finally, a better measurement and other improvements to refine the results are also proposed.
43 PARTICLE ACCELERATORS↗
Post-DTL Beam Delivery
Ensuring that the beam delivered from the upgraded Front-End (FE) meets the Key Performance Parameters (KPPs) at each user facility is critical to the success of the LANSCE Accelerator Modernization Project (LAMP). For a high-intensity, multi-user facility like LANSCE, compliance with beam loss and radiation thresholds is as important as the charge delivered to each target. While early LAMPF/LANSCE operations relied on iterative tuning to minimize losses from beam halo and tail particles, the new FE may introduce different beam distributions and loss modes—making predictive modeling essential. To manage this, the F2E (Front-End to End) effort is developing detailed particle-tracking models that reflect realistic beamline conditions, including halo formation and expected diagnostic readings. These "snapshot" simulations aim to benchmark live machine performance at a given moment. This will help quantify how beam quality from the new FE will propagate downstream through the facility. Only by validating these models can we confidently assess and mitigate the potential impacts of the LAMP FE on beam delivery. Post-DTL, the beam splits to serve five major user facilities. Historically, low-energy beam transport has been modeled using TRACE, and higher-energy sections with TRANSPORT. These have now been unified into MAD-X format and validated with codes such as Elegant, pyOrbit, XSuite, Impact-Z, and HPSim. The primary focus now is on accurate modeling of full particle distributions (including beam halo) as they traverse the accelerator and beamlines to each experimental station. All models are at various stages of validation with empirical data.
43 PARTICLE ACCELERATORS↗
Microtron Data Log
The Microtron at Los Alamos National Laboratory (LANL) is a versatile electron accelerator originally designed for medical therapy. Since 2001, it has been used for non-destructive radiographic imaging and research and development applications. Operating at four different energy levels—6, 10, 15, and 20 MeV—the Microtron produces dose rates of approximately 780, 1800, 2700, and 2800 R/min at a distance of one meter from the source, respectively. This high-energy X-ray source enables detailed internal examination of dense and thick objects without causing damage, making it invaluable for various scientific and industrial applications. For instance, LANL’s Microtron has been utilized to study the performance of large-panel cerium-doped lutetium yttrium silicon oxide (LYSO) scintillators, which are essential components in advanced imaging systems.
62 RADIOLOGY AND NUCLEAR MEDICINE↗
Unveiling the Hidden Evolution of Crystal Defects and Disorder in Energy Materials
Control of point defects and disorder in functional thin films and 2D materials is critical to realizing their full potential in applications ranging from energy storage to advanced electronics. However, these phenomena are often poorly understood, difficult to characterize, and challenging to direct with precision. This presentation explores emerging multi-modal computer vision to decipher and predict order in materials across multiple length scales in the electron microscope, from the atomic to the nanoscale. By fusing data from diverse sources, these powerful models provide unprecedented insights into materials' lifecycles, enabling the control of defects and their associated properties at a fundamental level. This capability promises to transform materials design and accelerate the development of next-generation technologies.
97 MATHEMATICS AND COMPUTING↗
TCF Base Commercialization Enabling Final Report: Lab Making Advanced Technology Commercialization Harmonized (MATCH) Prize
The Lab MATCH prize, funded by the Office of Technology Commercialization through the Technology Commercialization Fund, was designed to accelerate the commercialization of national laboratory intellectual property (IP) by incentivizing for-profit companies and startups to license lab IP aiming to enable more affordable, available, reliable and secure energy solutions. The Lab MATCH prize program offers both technical and commercial benefits, aligning with the Department of Energy's (DOE) mission to advance energy solutions through innovation, commercialization, and market-ready deployment. In summary, the Lab MATCH Prize promotes DOE's objectives by marrying technical innovation with commercialization expertise, resulting in scalable, market-ready solutions that strengthen the U.S. economy, advance energy technologies, and reaffirm U.S. leadership in energy innovation.
29 ENERGY PLANNING, POLICY, AND ECONOMY↗
Advances in genetic tools for metabolic engineering of non-conventional yeasts
Non-conventional yeasts are emerging as powerful alternatives to Saccharomyces cerevisiae for metabolic engineering, owing to their innate stress tolerance, broad substrate utilization, and distinctive metabolic capabilities. These attributes position them as promising chassis for producing biofuels, pharmaceuticals, and specialty chemicals. This review synthesizes recent advances in genetic toolkits for four such species—Pichia kudriavzevii (Issatchenkia orientalis), Starmerella bombicola, Debaryomyces hansenii, and Pachysolen tannophilus—highlighting progress across plasmid architectures (episomal and integrative), identification of autonomously replicating sequences and centromeric elements, and the development of safe-harbor genomic loci. We summarize promoter and terminator libraries enabling tunable expression, the expansion of auxotrophic and antifungal selection markers with recycling strategies, and the rapid adaptation of CRISPR-based systems (Cas9 and Cas12a) with optimized guide RNA expression, multiplex editing, and approaches that enhance homologous recombination (e.g., KU70/80 disruption). We also review landing-pad platforms for modular, repeated integrations and transposon-based tools (e.g., piggyBac) that facilitate multigene pathway assembly. Collectively, these innovations are accelerating design-build-test-learn cycles and enabling precise, scalable engineering of non-conventional yeasts. Remaining challenges—including limited species-specific episomal systems, variable transformation efficiencies, genome-stability concerns, and alternative codon usage—define clear priorities for future toolkit development. Together, these advances and open needs chart a path toward robust, sustainable biomanufacturing using diverse non-conventional yeast chassis.
59 BASIC BIOLOGICAL SCIENCES↗
New Concepts for a High Power 805 MHz RF Amplifier for LANSCE using Gallium Nitride Semiconductors
Explore the source record for details and available documents.
Accelerator Design, Technology, and Operations↗
Investigation of Unstructured Mesh Utilization in MCNP at LANSCE
Explore the source record for details and available documents.
Accelerator Design, Technology, and Operations↗
FENIX: An Open-Source Multiphysics Integrated Framework Enabling Collaborative Development of Plasma Facing Component Modeling Capabilities
Advanced modeling and simulation tools have a crucial role to play in accelerating fusion energy deployment as a sustainable power source. Multiphysics, high-fidelity computational tools can help understand, model, and quantify the complex interactions between materials performance, plasma and neutron exposure, and engineering processes. As a result, they accelerate the design, safety analysis, and performance evaluation of fusion systems. This webinar introduces the Fusion ENergy Integrated multiphys-X (FENIX) framework, an open-source multiphysics tool for plasma facing component modeling. FENIX leverages the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework, which has been developed by the United States Department of Energy Nuclear Energy Advanced Modeling and Simulation (NEAMS) program. FENIX couples various MOOSE capabilities such as heat transfer, thermomechanics, thermal hydraulics, electromagnetics, and plasma kinetics with the MOOSE-based applications Cardinal (neutronics) and TMAP8 (tritium transport). During the webinar, we will present FENIX and discuss how its modularity, openness, software quality assurance processes, and licensing approach supports effective collaborations, including public-private partnerships.
11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Forced RF generation of CW magnetrons for superconducting accelerators
CW magnetrons, designed and optimized for industrial RF heaters, were suggested to power Superconducting RF cavities due to their higher efficiency and lower cost than traditional klystrons, IOT’s, or solid-state amplifiers. RF amplifiers driven by a master-oscillator serve as coherent RF sources. CW magnetrons are regenerative RF generators with a huge regenerative gain. Very large regenerative gain causes instability with intense noise when a magnetron operates with the anode voltage higher than the threshold of self-excitation. Traditionally for stabilization of magnetrons is used injection-locking by a quite small signal. In this case the CW magnetrons do not provide correlation of the magnetron startup with the injection-locking signal. Thus, the magnetron except the injection locked oscillations may generate large noise. This may increase emittance of the beam in SRF accelerators. Recently we have developed mode for forced RF generation of CW magnetrons when the magnetron startup is provided by the injected forcing signal and the regenerative noise is suppressed. The mode is most suitable for SRF accelerators. The mode is briefly described below.
43 PARTICLE ACCELERATORS↗
Explainable physics-based constraints on reinforcement learning for accelerator optimization
We present a reinforcement learning (RL) framework for optimizing particle accelerator experiments that builds explainable physics-based constraints on agent behavior. The goal is to increase transparency and trust by letting users verify that the agent’s decision-making process incorporates suitable physics. Our algorithm uses a learnable surrogate function for physical observables, such as energy, and uses them to fine-tune how actions are chosen. This surrogate can be represented by a neural network or by an interpretable sparse dictionary model. We test our algorithm on a range of particle accelerator optimization environments designed to emulate the Continuous Electron Beam Accelerator Facility at Jefferson Lab. By examining the mathematical form of the learned constraint function, we are able to confirm the agent has learned to use the established physics of each environment. In addition, we find that the introduction of a physics-based surrogate enables our RL algorithms to reliably converge for difficult high-dimensional accelerator optimization environments.
explainability↗
Expediting field-effect transistor chemical sensor design with neuromorphic spiking graph neural networks
Improving the sensitive and selective detection of analytes in a variety of applications requires accelerating the rational design of field-effect transistor (FET) chemical sensors. Achieving high-performance detection relies on identifying optimal probe materials that can effectively interact with target analytes, a process traditionally driven by chemical intuition and time-consuming trial-and-error methods. To address the difficulties in probe screening for FET sensor development, this work presents a methodology that combines neuromorphic machine learning (ML) architectures, specifically a hybrid spiking graph neural network (SGNN), with an enriched dataset of physicochemical properties through semi-automated data extraction using large language models. Achieving a classification accuracy of 0.89 in predicting sensor sensitivity categories, the SGNN model outperformed traditional ML techniques by leveraging its ability to capture both global physicochemical properties and sparse topological features through a hybrid modeling framework. Next-generation sensor design was informed by the actionable insights into the connections between material properties and sensing performance offered by the SGNN framework. Through virtual screening for the detection of per- and polyfluoroalkyl substances (PFAS) as a use case, the effectiveness of the SGNN model was further validated. Density functional theory simulations confirmed graphene as a promising active material for PFAS detection as suggested by the SGNN framework. By bridging gaps in predictive modeling and data availability, this integrated approach provides a strong foundation for accelerating advancements in FET sensor design and innovation.
Ferreira, Rodrigo Pires [Univ. of Chicago, IL (Uni↗
Exploring Causes of Beam Loss at CEBAF
At Jefferson Lab, the Continuous Electron Beam Accelerator (CEBAF) features a unique design with two linear accelerators and two arc sections allowing for multiple turns of the electron beam, as well as four experimental end stations. This topology leads to increased beam losses, especially in the spreader and recombiner regions connecting the arcs to the linacs and in the extraction regions connecting the experimental end stations to the accelerator. These losses result in equipment activation and operational interruptions. Recent upgrades to the facility’s diagnostic systems, including the addition of xenon ion chambers, have provided higher-resolution data regarding these loss events. Building on this improved observational capability, we are developing a simulation framework using optics codes and the Geant4-based BDSIM to model beam extinction and halo formation in these regions. This work aims to correlate simulation results with experimental data to isolate the causes of beam loss and inform future machine tuning strategies. We present a summary of conclusions drawn from recent operational studies and outline a plan to model the beam loss and validate the simulations.
Matthews, C. [Old Dominion Univ., Norfolk, VA (Uni↗
Bayesian optimization algorithms for accelerator physics
Accelerator physics relies on numerical algorithms to solve optimization problems in online accelerator control and tasks such as experimental design and model calibration in simulations. The effectiveness of optimization algorithms in discovering ideal solutions for complex challenges with limited resources often determines the problem complexity these methods can address. The accelerator physics community has recognized the advantages of Bayesian optimization algorithms, which leverage statistical surrogate models of objective functions to effectively address complex optimization challenges, especially in the presence of noise during accelerator operation and in resource-intensive physics simulations. In this review article, we offer a conceptual overview of applying Bayesian optimization techniques toward solving optimization problems in accelerator physics. We begin by providing a straightforward explanation of the essential components that make up Bayesian optimization techniques. We then give an overview of current and previous work applying and modifying these techniques to solve accelerator physics challenges. Finally, we explore practical implementation strategies for Bayesian optimization algorithms to maximize their performance, enabling users to effectively address complex optimization challenges in real-time beam control and accelerator design. Published by the American Physical Society 2024
43 PARTICLE ACCELERATORS↗
Effects of Surface Treatments on the Outgassing of 3D-Printed 316L Stainless Steel.
Fermi National Accelerator Laboratory (Fermilab) is a world leader in designing and operating particle accelerators for nuclear and particle physics research. These accelerators rely on electric fields to propel particle beams, which are then directed and focused using magnetic fields. To ensure these beams travel without interference, they must move through an ultra-high vacuum environment, typically around 10⁻⁹ torr. Maintaining such a vacuum requires materials with exceptionally low outgassing rates. 316L stainless steel is a common material choice for vacuum systems due to its low outgassing rates, excellent corrosion resistance, non-magnetic properties, and high mechanical strength. When manufactured using traditional methods like machining, extrusion, and casting, the vacuum properties of 316L stainless steel are well understood. However, the behavior of 316L stainless steel produced through additive manufacturing, such as Direct Metal Laser Sintering (DMLS), is not as well documented. This study aims to determine the outgassing rate of 316L stainless steel fabricated using DMLS. The investigation focuses on measuring the outgassing rates of 1.5 2 vacuum reducers and evaluating the effects of surface preparation techniques, such as mechanical polishing and electropolishing, on the outgassing performance. Understanding the outgassing performance of 3D-printed 316L stainless steel could enable Fermilab engineers to adopt this fabrication method for producing complex parts designed for ultra-high vacuum environments. These advancements have the potential to benefit projects, such as the Long-Baseline Neutrino Facility (LBNF) and the Proton Improvement Plan-II (PIP-II), by improving design flexibility and fostering innovation in accelerator development.
Cloud, Jaiden [Central State University]↗
Progress in the development of the community Particle Accelerator Lattice Standard (PALS)
The Particle Accelerator Lattice Standard (PALS) is a community effort to create an open standard to promote lattice information exchange for particle accelerators. PALS development is a community-wide international effort involving accelerator physicists from multiple institutions. While it started as a lattice standard for beam dynamics simulations, it is now being extended to support other particle accelerator activities, in particular accelerator operation. With new accelerators that are becoming more complex, larger collaborations and the increasing imprint of artificial intelligence in all accelerator activities (from design to operation to workforce development), the imperative for a common, standardized accelerator ontology has been transitioning from “nice-to-have” to “must-have”. We will present the status of the project, its relations to other projects, including to two of the particle accelerator projects of the newly announced US DOE Genesis Mission: the Multi-Office Accelerator Team (MOAT) project and the Nuclear physics AI-Ready Accelerator Data (NARAD) project.
Brynes, A. [Science and Technology Facilities Coun↗