SEARCH · Search NASA

Results for “Additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1972

Activation energies for addition of O/3P/ to simple olefins.

Description of relative rate measurements for the addition of O(3P) to C2H4, C2F4, C3H6, and C4H8-1 in liquid argon at 87.5 K. The data strongly indicate that the activation energies for the addition of O(3P) to the double bonds of propylene and butene-1 are identical, probably to within 0.1 kcal/mole. It is very doubtful that differences in pre-exponential factors or other factors such as solvent effects, could invalidate this conclusion. A similar argument holds for the C2H4 and C2F4 reactions. Furthermore, the experiments suggest that the activation energy for addition of O(3P) to the double bond of butene-1 is about 0.1 kcal/mole.

Demore, W. B.↗

NASA NTRS1975

An investigation on the effect of second-order additional thickness distributions to the upper surface of an NACA 64 sub 1-212 airfoil

An investigation was conducted on a CDC 7600 digital computer to determine the effects of additional thickness distributions to the upper surface of an NACA 64 sub 1 - 212 airfoil. Additional thickness distributions employed were in the form of two second-order polynomial arcs which have a specified thickness at a given chordwise location. The forward arc disappears at the airfoil leading edge, the aft arc disappears at the airfoil trailing edge. At the juncture of the two arcs, x = x, continuity of slope is maintained. The effect of varying the maximum additional thickness and its chordwise location on airfoil lift coefficient, pitching moment, and pressure distribution was investigated. Results were obtained at a Mach number of 0.2 with an angle-of-attack of 6 degrees on the basic NACA 64 sub 1 - 212 airfoil, and all calculations employ the full potential flow equations for two dimensional flow. The relaxation method of Jameson was employed for solution of the potential flow equations.

Hague, D. S.↗

NASA NTRS1975

An investigation on the effect of second-order additional thickness distributions to the upper surface of an NACA 64-206 airfoil

An investigation was conducted on a CDC 7600 digital computer to determine the effects of additional thickness distributions to the upper surface of an NACA 64-206 airfoil. Additional thickness distributions employed were in the form of two second-order polynomial arcs which have a specified thickness at a given chordwise location. The forward arc disappears at the airfoil leading edge, the aft arc disappears at the airfoil trailing edge. At the juncture of the two arcs, x = x, continuity of slope is maintained. The effect of varying the maximum additional thickness and its chordwise location on airfoil lift coefficient, pitching moment, and pressure distribution was investigated. Results were obtained at a Mach number of 0.2 with an angle-of-attack of 6 degrees on the basic NACA 64-206 airfoil, and all calculations employ the full potential flow equations for two dimensional flow. The relaxation method of Jameson was employed for solution of the potential flow equations.

Merz, A. W.↗

NASA NTRS1975

Theoretical effect of modifications to the upper surface of two NACA airfoils using smooth polynomial additional thickness distributions which emphasize leading edge profile and which vary quadratically at the trailing edge

An investigation was conducted on a CDC 7600 digital computer to determine the effects of additional thickness distributions to the upper surface of the NACA 64-206 and 64 sub 1 - 212 airfoils. The additional thickness distribution had the form of a continuous mathematical function which disappears at both the leading edge and the trailing edge. The function behaves as a polynomial of order epsilon sub 1 at the leading edge, and a polynomial of order epsilon sub 2 at the trailing edge. Epsilon sub 2 is a constant and epsilon sub 1 is varied over a range of practical interest. The magnitude of the additional thickness, y, is a second input parameter, and the effect of varying epsilon sub 1 and y on the aerodynamic performance of the airfoil was investigated. Results were obtained at a Mach number of 0.2 with an angle-of-attack of 6 degrees on the basic airfoils, and all calculations employ the full potential flow equations for two dimensional flow. The relaxation method of Jameson was employed for solution of the potential flow equations.

Merz, A. W.↗

NASA NTRS1975

Effect of additions of coarse grains and fibers on the densification of a sinterable SiC

This note reports the effects on densification of independent additions of coarse equiaxed SiC grains and fibrous SiC that were mixed with fine beta-SiC to develop a duplex microstructure with improved toughness. The fine-matrix SiC did not contain excess boron and carbon. The equiaxed CVD beta-SiC was introduced in the fine beta-SiC matrix material in amounts of 5 and 10 wt%. Results indicate that the CVD beta-SiC, which is quite coarse, exhibits little indication of sinterability. The effect of these coarse-grained and fibrous additions on the sinterability of fine beta-SiC may result from a geometric type of interaction. This interpretation is reinforced by X-ray diffraction of the powders and sintered pellets via monochromatic CuK-alpha radiation; the diffraction patterns of the sintered composite structures are virtually a combination of those of the components. The addition of nonsinterable SiC to the sinterable material slightly reduces sinterability, the larger particles interacting geometrically with the fine matrix material to prevent complete densification.

Abe, H.↗

NASA NTRS1976

Effect of a chromium-containing fuel additive on hot corrosion

Four superalloys were tested at 900 C in high velocity combustion gases containing synthetic sea salt and, in some cases, a chromium containing fuel additive. While the additive reduced hot corrosion of the alloys over the 100 hour test period, the attack was not eliminated nor was the mode of attack changed. Reduction of the number of thermal cycles had as large a beneficial effect as the Cr additive. Intermittent washing during testing had either small beneficial or adverse effects depending on the alloy.

Lowell, C. E.↗

NASA NTRS1977

Analysis of economics of a TV broadcasting satellite for additional nationwide TV programs

The influence of a TV broadcasting satellite, transmitting four additional TV networks was analyzed. It is assumed that the cost of the satellite systems will be financed by the cable TV system operators. The additional TV programs increase income by attracting additional subscribers. Two economic models were established: (1) each local network is regarded as an independent economic unit with individual fees (cost price model) and (2) all networks are part of one public cable TV company with uniform fees (uniform price model). Assumptions are made for penetration as a function of subscription rates. Main results of the study are: the installation of a TV broadcasting satellite improves the economics of CTV-networks in both models; the overall coverage achievable by the uniform price model is significantly higher than that achievable by the cost price model.

Becker, D.↗

NASA NTRS1977

Effectiveness of various organometallics as antiwear additives in mineral oil

Sliding friction experiments were conducted with 1045 steel contacting 302 stainless steel and lubricated with various organometallics in mineral oil. Auger emission spectroscopy was used to determine the element present in the wear contact zone. The results indicate that there are organometallics which are as effective an antiwear additives as the commonly used zinc dialkyl dithiophosphate. These include dimethyl cadmium, triphenyl lead thiomethoxide, and triphenyl tin chloride. The additives were examined in concentrations to 1 weight percent. With dimethyl cadmium at concentrations of 0.5 weight percent and above, cadmium was detected in the contact zone. Coincident with the detection of cadmium, a marked decrease in the friction coefficient was observed. All additives examined reduced friction, but only the aforementioned reduced wear to a level comparable to that observed with zinc dialkyl dithiophosphate.

Buckley, D. H.↗

NASA NTRS1972

Aerodynamic characteristics of an NASA supercritical-wing research airplane model with and without fuselage area-rule additions at Mach 0.25 to 1.00

Transonic pressure tunnel tests at Mach numbers from 0.25 to 1.00 were performed to determine the effects of area-rule additions to the sides of the fuselage on the aerodynamic characteristics of a 0.087 scale model of an NASA supercritical-wing research airplane. Presented are the longitudinal aerodynamic force and moment characteristics for horizontal-tail deflection angles of -2.5 deg and -5 deg with the side fuselage area-rule additions on and off the model. The effects of the side fuselage area-rule additions on selected wing and fuselage pressure distributions at near-cruise conditions are also presented.

Bartlett, D. W.↗

NASA NTRS1980

Effects of oxide additions and temperature on sinterability of milled silicon nitride

Specimens of milled alpha-Si3N4 with 0 to 5.07 equivalent percent of oxide additions were pressureless sintered at 1650 to 1820 C for 4 hours in nitrogen while covered with powdered Si3N4 + SiO2. Densities of less than or equal to 97.5 percent resulted with approximately 2.5 equivalent percent of MgO, CeO2, Y2O3, and three mixtures involving these oxides. Densities of greater than or equal to 94 percent were obtained with approximately 0.62 equivalent percent of the same additives. At most temperatures, best sinterability (density maxima) was obtained with 1.2 to 2.5 equivalent percent additive.

Arias, A.↗

NASA NTRS1981

Development of new addition-type composite resins

The most promising of a number of new addition type polyimides and polyaromatic melamine (NCNS) resins for use in high performance composite materials. Three different cure temperature ranges were of interest: 530-560 K (500-550 F), 475-530 K (400-500 F), and 450 K (350 F). Examined were a wide variety of polyimide precursors terminated with 5 norbornene groups and addition polymerized at 560 K similar to PMR-15 and LARC-160 polyimides. In addition, a number of lower curing cinnamal end capped polyimides and a bismaleimide were investigated but were not found promising. A group of NCNS resins were investigated and some were found to be superior to current epoxy resins in moisture resistance, oxidative aging and flame and smoke properties.

Kray, R. J.↗

NASA NTRS1981

Formation of peptides from amino acids by single or multiple additions of ATP to suspensions of nucleoproteinoid microparticles

The synthesis of peptides from individual amino acids or pairs of amino acids and ATP in the presence of catalysis by nucleoproteinoid microparticles is investigated. Experiments were performed with suspensions formed from the condensation of lysine-rich and acidic proteinoids with polyadenylic acid, to which were added glycine, phenylalanine, proline, lysine or glycine-phenylalanine mixtures, and ATP either at once or serially. Peptide yields are found to be greatest for equal amounts of acidic and basic proteinoids. The addition of imidazole is found to alter the preference of glycine-phenylalanine mixtures to form mixed heteropeptides rather than homopeptides. A rapid ATP decay in the peptide synthesis reaction is observed, and a greater yield is obtained for repeated small additions than for a single addition of ATP. The experimental system has properties similar to modern cells, and represents an organizational unit ready for the evolution of associated biochemical pathways.

Nakashima, T.↗

NASA NTRS1984

Hot-pressed silicon nitride with various lanthanide oxides as sintering additives

The effects of addition of various lanthanide oxides and their mixture with Y2O3 on the sintering of Si3N4 were investigated. The addition of simple and mixed lanthanide oxides promoted the densification of Si3N4 in hot-pressing at 1800 C under 300-400kg/ centimeters squared for 60 min. The crystallization of yttrium and lanthanide-silicon oxynitrides which was observed inn the sintered body containing yttrium-lanthanide mixed oxides as additives led to the formation of a highly refractory Si3N4 ceramic having a bending strength of 82 and 84 kg/millimeters squared at room temperature and 1300 C respectively. In a Y2O3+La2O3 system, a higher molar ratio of La2O3 to Y2O3 gave a higher hardness and strength at high temperatures. It was found that 90 min was an optimum sintering time for the highest strength.

Ueno, K.↗

NASA NTRS1984

Optical and other property changes of M-50 bearing steel surfaces for different lubricants and additive prior to scuffing

An ester lubricant base oil containing one or more standard additives to protect against wear, corrosion, and oxidation was used in an experimental ball/plate elastohydrodynamic contact under load and speed conditions such as to induce scuffing failure in short times. Both the ball and the plate were of identically treated M-50 steel. After various periods of operating time the wear track on the plate was examined with an interference microscope of plus or minus 30 A depth resolution and sometimes also with a scanning ellipsometer and an Auger spectrometer. The optically deduced surface profiles varied with wavelength, indicating the presence of surface coatings, which were confirmed by the other instruments. As scuffing was approached, a thin (approximately A) oxide layer and a carbide layer formed in the wear track in particular when tricresylphosphate antiwear additive was present in the lubricant. The rates of the formation of these layers and their reactivity toward dilute alcholic HCl depended strongly on the lubricant and additives. Based on these results suggestions for improved formulations and a test method for bearing reliability could be proposed.

Lauer, J. L.↗

NASA NTRS1984

Statistical tests of additional plate boundaries from plate motion inversions

The application of the F-ratio test, a standard statistical technique, to the results of relative plate motion inversions has been investigated. The method tests whether the improvement in fit of the model to the data resulting from the addition of another plate to the model is greater than that expected purely by chance. This approach appears to be useful in determining whether additional plate boundaries are justified. Previous results have been confirmed favoring separate North American and South American plates with a boundary located beween 30 N and the equator. Using Chase's global relative motion data, it is shown that in addition to separate West African and Somalian plates, separate West Indian and Australian plates, with a best-fitting boundary between 70 E and 90 E, can be resolved. These results are generally consistent with the observation that the Indian plate's internal deformation extends somewhat westward of the Ninetyeast Ridge. The relative motion pole is similar to Minster and Jordan's and predicts the NW-SE compression observed in earthquake mechanisms near the Ninetyeast Ridge.

Stein, S.↗

NASA NTRS1986

Lubricants and Additives Affect Spur-Gear Fatigue

Surface-fatigue tests conducted with AISI 9310 steel spur gears show surface-fatigue life of AISI 9310 steel spur gears increased as much as 400 percent by addition of small amount of phosphorus-type extreme-pressure (EP) additive in lubricant. Antiwear or EP additives either absorbed onto surface or react with surface to form protective coating or surface film. Boundary film provides barrier that prevents contact of metal surfaces and provides low shear strength, which reduces friction coefficient below base metal.

Scibbe, H.↗

NASA NTRS1986

Optical and other properties changes of M-50 bearing steel surfaces for different lubricants and additives prior to scuffing

An ester lubricant base oil containing one or more standard additives to protect against wear, corrosion, and oxidation was used in an experimental ball/plate elastohydrodynamic contact under load and speed conditions such as to induce scuffing failure in short times. Both the ball and the plate were of identically treated M-50 steel. After various periods of operating time the wear track on the plate was examined with an interference microscope of plus or minus 30 A depth resolution and sometimes also with a scanning ellipsometer and an Auger spectrometer. The optically deduced surface profiles varied with wavelength, indicating the presence of surface coatings, which were confirmed by the other instruments. As scuffing was approached, a thin (approximately A) oxide layer and a carbide layer formed in the wear track in particular when tricresylphosphate antiwear additive was present in the lubricant. The rates of the formation of these layers and their reactivity toward dilute alcoholic HCl depended strongly on the lubricant and additives. Based on these results suggestions for improved formulations and a test method for bearing reliability could be proposed.

Lauer, J. L.↗

NASA NTRS1988

A new synthetic route to a family of non-classical addition-type thermoplastics. I - Concept and demonstration

A synthesis scheme was developed for a host of nonclassical addition-type thermoplastics (ATT) that can be cured by an addition reaction, leading to a linear polymer structure. The synthesis involves the reaction of an acetylene-terminated prepolymer with either a bismaleimide (BMI) or a biscitraconimide. A new polymer, designated LaRC-RP80, synthesized using this scheme, was found to exhibit several significantly improved properties over the commercial BMI, Kerimid 601, including an eight-fold increase in toughness while maintaining a high Tg, a higher (by 167 C) heat stability, and a 50-percent increase in moisture resistance. In addition, LaRC-RP80 has good hot/wet lap shear strength and processes easily at 288 C without voids in the finished product.

Pater, Ruth H.↗