Search NASA⌕ Search

SEARCH · Search NASA

Results for “Additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

An Additively Manufactured Fe-3Si Stator for a High-Performance Electrical Motor

Additive manufacturing (AM) has the potential to produce novel high-performance electrical machines, enabling the direct printing of complex shapes and the simultaneous processing of multiple feedstocks in a single build. We examined the properties and functional performance of Fe-3 wt.% Si materials that were printed via selective laser melting, machined down to thin laminates, and stacked to form a stator core of a prototype brushless permanent-magnet electrical motor. Big Area Additive Manufacturing of Nd2Fe14B (NdFeB)–polyphenylene sulfide (PPS) bonded magnets was performed, with them then being magnetized and used for the rotor. The magnetic, mechanical, and electrical properties of the as-printed and various heat-treated thin laminates and the back electromotive force (EMF) of the electrical motors at different rotational speeds were measured. The thin laminates exhibit a maximum relative permeability of 7494 at an applied field of 0.8 Oe and a core loss of about 20 W/lb at 60 Hz with the maximum induction of 15 kg. In addition to the demonstration of AM printing, motor assembly, and complete characterization of printed Fe-3 wt.% Si, this report highlights the areas of improvement needed in printing technologies to achieve AM built electrical motors and the need for isotropic microstructure refinements to make the laminates appropriate for high-mechanical-strength and low-loss rotational electrical devices.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Data for "Integrated ab initio modelling of atomic order and magnetic anisotropy for rare-earth-free magnet design: effects of alloying additions in L1 0 FeNi."

We describe an integrated modelling approach to accelerate the search for novel, single-phase, multicomponent materials with high magnetocrystalline anisotropy (MCA). For a given system we predict the nature of atomic ordering, its dependence on the magnetic state, and then proceed to describe the consequent MCA, magnetisation, and magnetic critical temperature (Curie temperature). Crucially, within our modelling framework, the same ab initio description of a material’s electronic structure determines all aspects. We demonstrate this holistic method by studying the effects of alloying additions in FeNi, examining systems with the general stoichiometries Fe 4 Ni 3 X and Fe 3 Ni 4 X, for additives including X = Pt, Pd, Al, and Co. The atomic ordering behaviour predicted on adding these elements, fundamental for determining a material’s MCA, is rich and varied. Equiatomic FeNi has been reported to require ferromagnetic order to establish the tetragonal L1 0 order suited for significant MCA. Our results show that when alloying additions are included in this material, annealing in an applied magnetic field and/or below a material’s Curie temperature may also promote tetragonal order, along with an appreciable effect on the predicted hard magnetic properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of Si Content in Electrode and SiO2 Additions to the Slag during Electroslag Remelting

Evolution of Si concentration in 316 stainless steel electrodes was observed during a melting campaign consisting of recycling electroslag remelted (ESR) ingots to make new electrodes using vacuum induction melting (VIM). This campaign consisted of iterations of VIM + ESR operations to optimize melting parameters. The effect of Si content on the melt parameters and ingot quality was further evaluated and additions of SiO2 to the slag chemistry were studied using research-scale experiments, x-ray diffraction (XRF), combustion analysis, visual inspections, and computational tools. The Si concentration was found to decrease by approximately 600 ppm following ESR of 150 lb. research-scale electrodes. Eventually, this led to failure of the slag skin and direct ingot/crucible contact. Additions of SiO2 to the slag at levels matching the original calculated Si concentration in the electrode did not eliminate the slag skin failure and the current during steady state increased to maintain a constant melt rate. In this investigation, we propose a mechanism of slag skin failure consisting of local concentration of current density due to absence, or breakage, of the SiO2 layer around the molten metal drop during ESR. This theory was reinforced by additional experiments in which Nb was added to the electrode to change the structure of the oxide layer around the drops.

Jablonski, Paul↗
DOE OSTI2024

Titanium Wire Arc Additive Manufacturing Inert Enclosure and Material Handling Safety Considerations

Wire arc additive manufacturing (WAAM) via metal inert gas (MIG)/gas metal arc welding (GMAW) is a viable option for fabrication of large-scale titanium parts; however, it introduces new safety hazards associated with both the material and the additional system hardware required for the process. Localized gas shielding of the weld arc via standard GMAW torch is inadequate for titanium due to its affinity for oxygen; thereby requiring the use of an inert enclosure to protect the weld from entraining oxygen. The use of the inert enclosure presents potential safety hazards such as operator asphyxiation and brings up discussion of confined space considerations. In addition, the titanium welding process creates pyrophoric titanium soot residue around the deposit, which can undergo deflagration during part cleaning and part removal. This paper provides an overview of the titanium WAAM process along with safety considerations for the design and operation of the inert enclosure as well as functional solutions for the safe handling of the titanium soot by-product.

Walters, Alex↗
DOE OSTI2025

Volumetric Additive Manufacturing of Dormant Catalytic Chemistries to Generate Silicone Micro‐ and Millifluidic Devices and Instant Molds

Tomographic volumetric additive manufacturing (T‐VAM) rapidly prints solid objects within minutes, accessing photochemistries that are traditionally challenging for layer‐based additive manufacturing methods. This includes high‐viscosity materials, air‐free chemistries, and solid‐state systems. Catalytic chemistries are appealing as a pathway to engineering advanced materials, including tough thermosets, silicone elastomers, and complex block copolymers. However, photoactivated dormant catalytic chemistries, where the catalyst irreversibly activates upon exposure to light, are incompatible with typical tomographic VAM approaches. To address this limitation, a zero‐dose optimization strategy is devised to preserve dormant catalysts in desired regions by keeping them unexposed to light. VAM printed micro‐ and millifluidic devices and instant molds are successfully produced within minutes in silicones polymerized using photoactivated dormant platinum photohydrosilylation catalysts. The printed channels are programmed to be 500 and 2500 µm for the micro‐ and millifluidic devices, and print fidelity is assessed by X‐ray computed tomography. This work demonstrates the potential of zero‐dose optimization to expand the range of chemistries accessible for VAM, enabling the rapid fabrication of complex devices.

Additive Manufacturing↗
DOE OSTI2025

Electroslag additive manufacturing: A pathway for high throughput near net shape production

Electroslag Additive Manufacturing (ESAM), a new high-throughput additive manufacturing (AM) method that combines Electroslag Strip Cladding (ESC) and wire arc AM (WAAM) is introduced. This combination enables the high deposition rate of ESC (more than 20 kg/h with a 60 mm strip electrode) to benefit from the precise geometric control of WAAM. As a precursor to ESAM, the ESC process is investigated in an AM context independently by evaluating both direct and staggered bead-stacking strategies and analyzing the microstructural and mechanical properties of each. This is followed by an ESAM demonstration producing an annular geometry by pairing ESC with gas tungsten arc welding (GTAW), wherein GTAW is utilized to construct annular walls that are subsequently infilled via ESC. The microstructure and mechanical properties of ESC-only AM are compared with that of the ESAM method and it is shown that printed integral retaining walls do not impact the resulting mechanical properties of ESAM. Furthermore, results indicate that ESAM-produced Alloy 625 parts exhibit tensile properties on par with cast counterparts, supporting the method’s scalability to components exceeding one metric ton, and possibly making ESAM a viable future manufacturing approach for competitive production of large-scale components currently manufactured by casting and forging.

Additive manufacturing↗
DOE OSTI2024

Development of Solid Synchronous Reluctance Rotors With Multi-Material Additive Manufacturing

Synchronous reluctance (SynR) machines are promising rare-earth material-free alternatives to permanent magnet machines. However, structural challenges limit their operating speed and power density. This paper proposes and investigates multi-material additive manufacturing (MMAM) as a key-enabler to realize power-dense and high-speed SynR machines. It does so by proposing designs that guide magnetic flux through solid rotors realized by selective placement of magnetic and non-magnetic materials. To explore this concept, first, material samples are additively manufactured and experimentally characterized to assess the structural and magnetic properties that can be expected for the proposed rotors. Second, the design space of each rotor type is explored using these measured properties within finite element analysis. The results reveal that MMAM can enable fabrication of SynR motors with power density levels that are at the leading edge of all conventional electric machine topologies. It is shown that tip speeds in excess of 300 m/s can be achieved, resulting in 3-4x improvement in power density over conventional SynR motors. A solid SynR rotor is printed in an experimental MMAM laser powder bed fusion system. The rotor is paired with an existing stator to create a functional SynR motor with a saliency ratio of 2.59 and torque rating of 4.15 Nm. This is the first publication of a SynR rotor prototype constructed via MMAM.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Machining of Thin-Walled Structures From Stiffness-Driven Additively Manufactured Preform Geometry

Additive manufacturing provides the means to build component preforms with reduced excess material to create functional parts. In the case of aero-structural and aero-engine components, additive manufacturing technologies offer the possibility to substantially reduce the volume of material to be removed by machining operations. To achieve this objective, the preform must be built with the minimum material necessary to contain the final geometry and simultaneously provide enough stiffness to withstand the magnitude of the machining forces. This work describes a computationally efficient method to calculate the geometry required from the preform to reliably manufacture typical thin-walled structures via finish machining processes. This is achieved by defining the preform with near constant static stiffness across the width of the preform, in combination with a prescribed magnitude of stiffness at the top edge of the preform. The prescribed static stiffness is the function of the machining force magnitude, a direct consequence of the preselected cutting conditions. In conclusion, this article illustrates the application of the method to a straight single boundary thin-walled structure as an introduction case and for ease of description.

Additive manufacturing↗
DOE OSTI2025

Unravelling Microstructure Selection in an Additively Manufactured Eutectic High‐Entropy Alloy

High-entropy alloys (HEAs) are promising candidates for advanced structural applications due to their excellent mechanical properties. Additive manufacturing (AM), with its rapid solidification conditions, enables the creation of unique nonequilibrium microstructures. To fully leverage the synergy between AM and HEAs, understanding how processing affects structure and properties is essential. Here, how solidification rate influences microstructure evolution and phase transformation pathway in laser additively manufactured AlCrFe2Ni2 eutectic HEAs is investigated. By increasing the laser scan speed and hence the solidification rate, distinct solidification modes evolving from coupled eutectic to anomalous eutectic and eventually to single-phase solidification are revealed. These transitions result in distinct microstructures and a wide range of mechanical properties. Thermodynamic modeling and molecular dynamics simulations reveal that low cooling rates allow for sufficient atomic diffusion and phase separation, facilitating coupled eutectic growth. In contrast, rapid cooling suppresses diffusion and destabilizes the solid–liquid interface, promoting anomalous or single-phase solidification. This integrated experimental and computational approach provides a multiscale understanding of solidification mechanisms in HEAs and underscores how kinetic effects can over-ride thermodynamic predictions under nonequilibrium conditions. Furthermore, these results demonstrate that AM can serve as a powerful tool to design HEAs with tailored microstructures and properties.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Hybrid Additive Manufacturing and Electric Field-Assisted Sintering of High-temperature Heat Exchangers via Sacrificial Channel Molds

A hybrid manufacturing approach, integrating additive manufacturing (AM) with powder methodology via electric field-assisted sintering (EFAS), was developed for the fabrication of high-temperature compact heat exchangers (CHX) from refractory metals. The methodology employed additively manufactured sacrificial channel molds (SCMs) as shapeholders for CHX channels, which were embedded in metal powders using EFAS. Following embedding, the SCMs were chemically dissolved to form the internal channel network. SCMs were fabricated using both digital light processing (DLP) and direct ink writing (DIW) from chemically reactive, calcium-based ceramic feedstocks with varying ratios of Al2O3 reinforcement. The microstructure, phase composition, and dissolution behavior of both as-printed and embedded SCMs were investigated. The shrinkage behavior of the SCMs embedded in refractory metals, as well as the interfacial characteristics between the SCMs and metal matrix, were studied. The results showed that the SCMs containing sufficient chemical reactive ceramics dissolved effectively before and after embedding. The as-printed SCMs retained the phase composition of their feedstocks, but the embedded SCMs containing calcium-based ceramics and Al2O3 exhibited the formation of calcium aluminates due to high temperature exposure during embedding. Most SCMs exhibited a cellular Al2O3 network filled with Ca-rich ceramics. Shrinkage after embedding was strongly dependent on SCM density, with lower density SCMs exhibiting greater shrinkage. A thin SCM-affected zone was observed at the metal matrix surface, characterized by increased porosity compared to the bulk matrix. This effect was attributed to infiltration of the SCM materials into powder particle boundaries under pressure, followed by their removal during dissolution. This study demonstrates the feasibility of manufacturing CHXs from hard-to-process refractory metals for use in harsh environments.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Microscale Metal Additive Manufacturing by Solid‐State Impact Bonding of Shaped Thin Films

The deposition of device-grade inorganic materials is one key challenge toward the implementation of additive manufacturing (AM) in microfabrication, and to that end, a broad range of physico-chemical principles has been explored for 3D fabrication with micro- and nanoscale resolution. Yet, for metals, a process that achieves material quality rivalling that of established thin-film deposition methods, and at the same time, has the potential to combine high throughput production with a broad palette of processable materials, is still lacking. Here, the kinetic, solid-state bonding of metal thin films for the additive assembly of high-purity, high-density metals with micrometer-scale precision is introduced. Indirect laser ablation accelerates micrometer-thick gold films to hundreds of meters per second without their heating or ablation. Their subsequent impact on the substrate above a critical velocity forms a permanent, metallic bond in the solid state. Stacked layers are of high density (>99%). By defining thin-film layers with established lithographic methods prior to launch, a variable feature size (2–50 µm), arbitrary shape of bonded layers, and parallel transfer of up to 36 independent film units in a single shot, is demonstrated. Thus, the solid-state kinetic bonding principle as a viable and potentially versatile route for micro-scale AM of metals is established.

3D printing↗
DOE OSTI2026

Computationally inexpensive part-scale thermal history of additive friction-stir deposition

This study presents an analytical model for steady-state power generation and tool heat loss in additive friction-stir deposition (AFSD), developed to enable part-scale thermal simulation while remaining computationally inexpensive. The model predicts total generated power, yielding 3.7–4.7 kW across deposition temperature setpoints of 400–460 °C for the deposition of AA6061 with a Be-Cu tool. This corresponds to 90–95% of the reported spindle power. Tool heat loss is experimentally determined by calibrating a steady-state energy balance between the generated power, the substrate-deposition thermal gradient, and a temperature dependent tool heat loss term: q tool (T) = a + b (T - 400°C) with a = 2.7 x 10 6 Wm -2 and b = 9.5 x 10 3 Wm -2 K -1 . The calibration indicates that about 69% of the generated heat is conducted into the tool for this configuration, which is much higher than previously reported. The calibrated heat-source is implemented in finite element software (Adamantine) to simulate the transient thermal history of a 100 cm 3 representative build in 8 min on a standard desktop (at 0.635 mm build-height resolution). For the first three layers, the substrate temperatures between simulation and experiment are within 10% mean absolute percentage error. Sensitivity analysis indicates that uncertainties in average deposition temperature and deformation localization (stir-zone geometry, depth, and spatial dependance of strain-rate and flow stress) dominate model variance, motivating additional experimental verification.

Additive Friction-Stir Deposition↗
DOE OSTI2025

Mechanical and Thermal Characterization of Additively Manufactured Carbon/Nylon 12 and Carbon/PEEK Composites

This study explores additive manufacturing of carbon fiber-reinforced thermoplastic composites using the Composite-Based Additive Manufacturing (CBAM) process. Carbon/Nylon 12 and Carbon/PEEK composites were fabricated and evaluated through mechanical (compression, tensile, flexural, and impact) and thermal (DSC and TGA) tests. Carbon/PEEK exhibited superior mechanical performance, with 97.5% higher tensile strength, 79.8% higher elastic modulus, and 59.6% higher flexural strength compared to Carbon/Nylon 12. Thermal testing showed that Carbon/PEEK had higher thermal stability, beginning degradation at 350 °C versus 298 °C for Carbon/Nylon. These results indicate that CBAM-fabricated Carbon/PEEK composites are suitable for applications requiring high strength and temperature resistance.

Additive manufacturing↗
DOE OSTI2024

Uncovering grain and subgrain microstructure at the scale of additive manufacturing melt tracks with a scalable cellular automaton solidification model

Metal additive manufacturing, characterized by rapid solidification, yields refined grains with a distinctive cellular subgrain microstructure that plays a pivotal role in determining material properties. Due to the significant computational expense demanded to simulate the required physics with submicron spatial resolution, their numerical simulations have been limited to proof-of-concept studies to either 2D or small subregions of a melt pool. In this study, an open-source, scalable, solidification code, muMatScale, based on the cellular automaton method, has been developed to predict the grain and the underlying subgrain microstructure over an entire melt pool. The model incorporates flexible parallelization schemes, utilizing MPI and OpenMP GPU Offloading, in addition to appropriate multi-physics specific to non-equilibrium rapid solidification in AM. The impact of nucleation parameters on grain microstructures was investigated with a focus on grain size variations and morphology transitions. With selected nucleation parameters, the simulation predicted the grain size, subgrain morphology, crystallographic orientation, and microsegregation aligned with experimental measurements. The model demonstrates that epitaxial grain growth is a dominant factor at the melt pool boundary, influencing grain size variation under different grain sizes in the build plate while maintaining consistent primary dendrite arm spacing under identical thermal conditions. Here, the highly efficient numerical model enables large-scale simulations with a spatial resolution of 100 nm or less, unveiling unprecedented insights into thermal and solutal diffusion driven grain growth, and the subgrains with microsegregation within grains in 3D across scales. muMatScale will enable the linking of submicron length-scale microstructure to part-level material behavior by investigating fundamental solidification problems at the intercellular scale in many-track and many-layer builds.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A dynamic volumetric heat source model for laser additive manufacturing

Melt pool scale models of laser powder bed fusion (LPBF) offer insights into the process-structure-property relationships in additive manufacturing (AM). These models often neglect physical phenomena such as vapor cavity formation and fluid mechanics to reduce computational demands. Instead, volumetric heat source models are used to represent the effects that these phenomena have on the predicted melt pool dimensions. Generally, the dimensions and effective absorption of the volumetric heat source are calibrated to reproduce melt pool dimensions observed in metallographic cross sections taken from single-track experiments on bare plate. However, the transient nature of LPBF often deviates the melt pool dimensions from the assumed steady-state conditions of single-track experiments, motivating the need for a volumetric heat source model that more generally considers the dynamic relationship between melt pool shape and laser-material interactions. Here, we introduce a two-parameter volumetric heat source model that integrates several existing models into a generalized mathematical expression, providing independent control over the radial heat distribution via the parameter k and the volumetric shape of the heat source via the parameter m. This parameterization enables the calibration of melt pool shape predictions through simultaneous adjustment of these parameters, while keeping the radial heat source dimensions consistent with the experimental spot size (D4σ) and constraining the heat source depth and absorption to physically derived expressions for cavities. Consequently, the proposed volumetric heat source model adapts to changes in the local melt pool conditions due to scanning strategy and part geometry by dynamically adjusting the heat source depth and absorption. We demonstrate the capabilities of the proposed model through comparisons with a collection of experiments from the Additive Manufacturing Benchmark (AMBench).

36 MATERIALS SCIENCE↗
DOE OSTI2025

Online thermal profile prediction for large format additive manufacturing: A hybrid CNN-LSTM based approach

Large format additive manufacturing (LFAM) is an advanced 3D printing technique that efficiently fabricates large-scale components through a layer-by-layer extrusion and deposition process. Accurate surface layer temperature monitoring is essential to prevent manufacturing failures and ensure final product quality. Traditional physics-based offline approaches for simulating thermal behavior are often inefficient and complex, posing challenges on real-time, in-situ monitoring. Here, to address this, we propose a data-driven hybrid CNN-LSTM model to predict sequential thermal images of arbitrary length using real-time infrared thermal imaging. In this approach, a Convolutional Neural Networks (CNN) is trained offline to capture spatial features, reduce dimensional complexity, and enhance time efficiency, while a stacked Long Short-Term Memory (LSTM) is applied online to capture temporal information for improved prediction of future thermal behavior in subsequent printing layers. Model performance is evaluated using MSE, SSIM, and PSNR metrics and is benchmarked against stacked LSTM and convolutional LSTM models, demonstrating superior accuracy and applicability. Additionally, to mitigate noise from moving extruders and gantry backgrounds in thermal images, a fine-tuned semantic segmentation model is implemented offline to extract printing geometry, enabling precise temperature tracking along the tool path for further thermal analysis. The frameworks developed in this study significantly advance temperature monitoring, thermal analysis, and in-situ manufacturing control for LFAM, bridging the gap between theoretical modeling and practical application.

Geometry extraction↗
DOE OSTI2025

Additive manufacturing of mullite ceramic by digital light processing

Mullite material was successfully additively manufactured using digital light processing (DLP). The printed geometry involves a one-step process of pyrolysis, de-binding, and sintering under a plain atmosphere to achieve an average of 76 % ceramic yield and linear shrinkage of 12 %. Furthermore, the thermal profile was carefully controlled to obtain consistent phases in which the XRD shows a mullite phase. Here, in addition, the Weibull analysis was conducted on the sintered flexural specimens, showing a Weibull modulus (m) of 13.05 with a characteristic strength (σ 0 ) of 94.96 MPa. Synchrotron microtomography was performed on the sintered specimens, which showed two distinct porosity distributions (small and large). Large porosity (non-spherical elongated) is the primary cause of decreased material strength, while small porosity (spherical) is the sintering product. The measured thermal conductivity of the specimens was in the range of 2.7–3.1 W/m∙k and decreased with an increase in temperature. Lastly, large-scale prototypes were printed concurrently with a fine resolution of 25 μm without any compromise on the predetermined design and structure.

Additive manufacturing↗
DOE OSTI2025

ExaCA v2.0: A versatile, scalable, and performance portable cellular automata application for additive manufacturing solidification

The previously established ExaCA software for performance portable alloy grain structure simulation has been updated to better represent the solidification behavior during complex alloy processing conditions, such as those encountered during metal additive manufacturing (AM), and for improved performance and scalability. Here, an extension to the time–temperature history input data format and the core ExaCA algorithm to include an arbitrary number of melting and solidification events yielded improved prediction of texture for various melt pool geometries, expanding the range of AM-relevant conditions that can be accurately simulated. Improved heat transport process simulation coupling, including the creation of large raster datasets from single track time–temperature history data and in-memory coupling with the new, performance portable finite difference code Finch, were also demonstrated in example studies on the effect of multilayer AM microstructure predictions on hatch spacing and cell size, respectively. Additional new features are detailed and demonstrated, including the ability to perform simulations using various interfacial response function forms, execute simulations on state-of-the-art hardware, improved usability through post-processing versatility, and improved strong and weak scaling performance. The performance, physics, and versatility improvements demonstrated here will further enable large-scale studies on AM process–microstructure relationships that were not previously possible. Furthermore, the usability improvements and ability to run coupled AM process–microstructure simulations using the Finch-ExaCA workflow will facilitate broader use of this open-source software by the computational materials community.

36 MATERIALS SCIENCE↗