Search NASA⌕ Search

SEARCH · Search NASA

Results for “Adverse pressure gradient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Measurements in Separated and Transitional Boundary Layers Under Low-Pressure Turbine Airfoil Conditions

Detailed velocity measurements were made along a flat plate subject to the same dimensionless pressure gradient as the suction side of a modern low-pressure turbine airfoil. Reynolds numbers based on wetted plate length and nominal exit velocity were varied from 50,000 to 300,000, covering cruise to takeoff conditions. Low and high inlet free-stream turbulence intensities (0.2% and 7%) were set using passive grids. The location of boundary-layer separation does not depend strongly on the free-stream turbulence level or Reynolds number, as long as the boundary layer remains non-turbulent prior to separation. Strong acceleration prevents transition on the upstream part of the plate in all cases. Both free-stream turbulence and Reynolds number have strong effects on transition in the adverse pressure gradient region. Under low free-stream turbulence conditions transition is induced by instability waves in the shear layer of the separation bubble. Reattachment generally occurs at the transition start. At Re = 50,000 the separation bubble does not close before the trailing edge of the modeled airfoil. At higher Re, transition moves upstream, and the boundary layer reattaches. With high free-stream turbulence levels, transition appears to occur in a bypass mode, similar to that in attached boundary layers. Transition moves upstream, resulting in shorter separation regions. At Re above 200,000, transition begins before separation. Mean velocity, turbulence and intermittency profiles are presented.

Volino, Ralph J.↗
NASA NTRS1997

Effect of Pressure Gradients on Plate Response and Radiation in a Supersonic Turbulent Boundary Layer

Using the model developed by the author for zero-pressure gradient turbulent boundary layers, results are obtained for adverse and favorable pressure gradients. It is shown that when a flexible plate is located in an adverse pressure gradient area, it vibrates more than if it were in a favorable pressure gradient one. Therefore the noise generated by the plate in an adverse pressure gradient is much greater than that due to the plate in a favorable pressure gradient. The effects of Reynolds number and boundary layer thickness are also analyzed and found to have the same effect in both adverse and favorable pressure gradient cases. Increasing the Reynolds number is found to increase the loading on the plate and therefore acoustic radiation. An increase in boundary layer thickness is found to decrease the level of the high frequencies and therefore the response and radiation at these frequencies. The results are in good qualitative agreement with experimental measurements.

Frendi, Abdelkader↗
DOE OSTI2024

A robust spectral element implementation of the $k - τ$ RANS model in Nek5000/NekRS

The $k - ω$ Reynolds Averaged Navier Stokes (RANS) model is one of the industry standard approaches for modeling of turbulent flows. It performs better than the $k - ϵ$ model for low Reynolds number flows and is also more suitable for boundary layers with adverse pressure gradients. Major drawback of the model, however, is that the asymptotic value of $ω$ at the walls is singular, necessitating the use of a contrived “sufficiently” large value for $ω$ as the boundary condition for its transport equation. Here, this invariably leads to the solution being sensitive to near wall grid spacing. While an acceptable solution for low order (finite volume) methods, the excessive near wall gradients lead to persistent numerical stability issues in high order codes. To alleviate the problem, specifically in the context of the high order spectral element code Nek5000, a regularized $k - ω$ approach was formulated in our prior work (Tomboulides et al., 2018). The formulation, however, relies on the use of wall distance and its gradients for modeling the closure terms and can pose problems for simulations in complex geometries. This work presents a novel implementation of the $k - τ$ RANS model in Nek5000, where $τ = 1/ω$, eliminating the need for regularization, owing to the asymptotically bounded behavior of the source terms in the $τ$ transport equation, and also eliminating dependence on wall distance. Robustness and stability of the $k - τ$ model is ensured through implicit treatment of the source terms and their careful numerical implementation and demonstrated through several cases aimed at verification and validation. Studies include both canonical and engineering relevant problems, viz., turbulent channel flow, pipe flow, backward facing step, flow over NACA 0012 airfoil and flow in a T-junction. Results from the $k - τ$ model are shown to be consistent with regularized $k - ω$ model and also with the $k - ω$ SST model in OpenFOAM (for select studies). Comparison with experimental data is also shown, where available, to bolster validation efforts for the $k - τ$ model implementation through prediction of key turbulent quantities of interest.

Nek5000↗
DOE OSTI2022

Adaptive Determination of the Optimal Exchange Location in Wall-Modeled Large-Eddy Simulation

Wall-modeled large-eddy simulation introduces a modeling interface (or exchange location) separating the wall-modeled layer from the rest of the domain. The current state-of-the-art is to rely on user expertise when choosing where to place this modeling interface, whether this choice is tied to the grid or not. This paper presents a postprocessing algorithm that determines the exchange location systematically. The algorithm is based on a model for the error in the predicted wall shear stress and a model for the computational cost, and then finds the exchange location that minimizes a combination of the two. Here, the algorithm is tested both a priori and a posteriori using an equilibrium wall model for the flow over a wall-mounted hump, a boundary layer in an adverse pressure gradient, and a shock/boundary-layer interaction. The algorithm produces exchange locations that mostly agree with what an experienced user would suggest, with thinner wall-modeled layers in nonequilibrium flow regions and thicker wall-modeled layers where the boundary layer is closer to equilibrium. This suggests that the algorithm should be useful in simulations of realistic and highly complex geometries.

42 ENGINEERING↗
DOE OSTI2025

Investigating the relationship between simulation parameters and flow variables in simulating atmospheric gravity waves for wind energy applications

Wind farms, particularly offshore clusters, are becoming larger than ever before. Besides influencing the surface wind flow and the inflow for downstream wind farms, large wind farms can trigger atmospheric gravity waves in the inversion layer and the free atmosphere aloft. Wind-farm-induced gravity waves can cause adverse pressure gradients upstream of the wind farm, which contribute to the global blockage effect, and can induce favorable pressure gradients above and downstream of the wind farm that enhance wake recovery. Numerical modeling is a powerful means of studying these wind-farm-induced atmospheric gravity waves, but it comes with the challenge of handling spurious reflections of these waves from domain boundaries. Typically, approaches which employ radiation boundary conditions and forcing zones are used to avoid these reflections. However, the simulation setup of these approaches relies heavily on ad hoc processes. For instance, the widely used Rayleigh damping method requires ad hoc tuning to produce a setup that may only produce satisfactory results for a particular case. To provide more systematic guidance on setting up realistic simulations of atmospheric gravity waves, we conduct a large-eddy simulation (LES) study of flow over a 2D hill and through a wind farm canopy that explores the optimum domain size and damping layer setup depending on the fundamental parameters which determine the flow characteristics. In this work, we only consider linearly stratified conditions (i.e., no inversion layer), thereby focusing on internal gravity waves in the free atmosphere and their reflections from the domain boundaries. This type of flow is governed by a single Froude number, which dictates most of the internal wave properties, such as wavelength, amplitude, and direction. This, in turn, will dictate the optimum domain size and Rayleigh damping layer setup. We find the effective horizontal and vertical wavelengths (the representative wavelengths of the entire wave spectrum) to be the appropriate length scales to size the domain and damping layer thickness, and the optimal Rayleigh damping coefficient scales with the Brunt–Väisälä frequency. Considering Froude numbers seen in wind farm applications, we propose recommendations to limit the reflections to less than 10 % of the total upward-propagating wave energy. Typically, damping is done at the top boundary, but given the non-periodic lateral boundary conditions of practical wind farm simulation domains, we find that damping the inflow–outflow boundaries is of equal importance to damping the top boundary. The Brunt–Väisälä frequency-normalized damping coefficient should be between 1 and 10. The damping layer thickness should be at least one effective vertical wavelength; damping layers exceeding 1.5 times the vertical wavelength are found to be unnecessary. The domain length and height should accommodate at least one effective horizontal and vertical wavelength, respectively. Moreover, Rayleigh damping does not damp the waves completely, and the non-damped energy might accumulate over the simulation time.

17 WIND ENERGY↗
NASA NTRS1972

Surface temperature effect on subsonic stall.

Results of an analytical and experimental study of boundary layer flow over an aerodynamic surface rejecting heat to a cool environment. This occurs following reentry of a Space Shuttle vehicle. Analytical studies revealed that a surface to freestream temperature ratio, greater than unity tended to destabilize the boundary layer, hastening transition and separation. Therefore, heat transfer accentuated the effect of an adverse pressure gradient. Wind tunnel tests of a 0012-64 NACA airfoil showed that the stall angle was significantly reduced while drag tended to increase for freestream temperature ratios up to 2.2.

Macha, J. M.↗
NASA NTRS1974

Differential analysis for the turbulent boundary layer on a compressor blade element (including boundary-layer separation)

A two-dimensional differential analysis is developed to approximate the turbulent boundary layer on a compressor blade element with strong adverse pressure gradients, including the separated region with reverse flow. The predicted turbulent boundary layer thicknesses and velocity profiles are in good agreement with experimental data for a cascade blade, even in the separated region.

Schmidt, J. F.↗
NASA NTRS1974

Evaluation of analytical procedures for prediction of turbulent boundary layers on a porous wall

An analytical study has been made to determine how well current boundary layer prediction techniques work when there is mass transfer normal to the wall. The data that were considered in this investigation were for two-dimensional, incompressible, turbulent boundary layers with suction and blowing. Some of the bleed data were taken in an adverse pressure gradient. An integral prediction method was used three different porous wall skin friction relations, in addition to a solid-surface relation for the suction cases. A numerical prediction method was also used. Comparisons were made between theoretical and experimental skin friction coefficients, displacement and momentum thicknesses, and velocity profiles. The integral method with one of the porous wall skin friction laws gave very good agreement with data for most of the cases considered. The use of the solid-surface skin friction law caused the integral to overpredict the effectiveness of the bleed. The numerical techniques also worked well for most of the cases.

Towne, C. E.↗
NASA NTRS1974

Analytical study of subsonic turbulent boundary layer separation including viscous-inviscid interaction

The prediction of boundary layer deceleration and separation in regions of adverse pressure gradients are discussed as an unsolved problem of fundamental practical importance in aerodynamics. A three layered theoretical flow model of boundary layer separation including viscous-inviscid interaction was conceived for the case of subsonic two dimensional steady laminar flow.

Inger, G. R.↗
NASA NTRS1975

Application of numerical optimization to the design of low speed airfoils

A practical procedure for the optimum design of low-speed airfoils is demonstrated. The procedure uses an optimization program based on the method of feasible directions coupled with an aerodynamic analysis program that uses a relaxation solution of the inviscid, full potential equation. Results are presented for airfoils designed to have small adverse pressure gradients, high maximum lift, and low pitching moment.

Hicks, R. M.↗
NASA NTRS1975

Asymptotic theory of two-dimensional trailing-edge flows

Problems of laminar and turbulent viscous interaction near trailing edges of streamlined bodies are considered. Asymptotic expansions of the Navier-Stokes equations in the limit of large Reynolds numbers are used to describe the local solution near the trailing edge of cusped or nearly cusped airfoils at small angles of attack in compressible flow. A complicated inverse iterative procedure, involving finite-difference solutions of the triple-deck equations coupled with asymptotic solutions of the boundary values, is used to accurately solve the viscous interaction problem. Results are given for the correction to the boundary-layer solution for drag of a finite flat plate at zero angle of attack and for the viscous correction to the lift of an airfoil at incidence. A rational asymptotic theory is developed for treating turbulent interactions near trailing edges and is shown to lead to a multilayer structure of turbulent boundary layers. The flow over most of the boundary layer is described by a Lighthill model of inviscid rotational flow. The main features of the model are discussed and a sample solution for the skin friction is obtained and compared with the data of Schubauer and Klebanoff for a turbulent flow in a moderately large adverse pressure gradient.

Melnik, R. E.↗
NASA NTRS1976

Heat-Transfer Characteristics of Partially Film Cooled Plug Nozzle on a J-85 Afterburning Turbojet Engine

Plug nozzle film cooling data were obtained downstream of a slot located at 42 percent of the total plug length on a J-85 engine. Film cooling reduced the aft end wall temperature as much as 150 K, reduced total pressure loss in the upstream convection cooling passages by 50 percent, and reduced estimated compressor bleed flow requirement by 14 percent compared to an all convectively cooled nozzle. Shock waves along the plug surface strongly influenced temperature distributions on both convection and film cooled portions. The effect was most severe at nozzle pressure ratios below 10 where adverse pressure gradients were most severe.

Nosek, S. M.↗
NASA NTRS1976

Comparison of solutions to boundary-layer and Navier-Stokes equations for the case of mass removal from a turbulent boundary layer

Comparisons are made over a range of Mach numbers from 1.5 to 7.5 at a fixed Reynolds number for various amounts of mass removal (boundary-layer bleed). Results indicate that boundary-layer theory can be used for design purposes in the range of bleed rates required to eliminate separation in an isolated, strong, adverse pressure gradient. Only about 5% to 10% of the boundary-layer mass flow must be removed to prevent such separations. Direct comparisons of bleed rates required to eliminate separation predicted by boundary-layer and Navier-Stokes equations for an M = 3.5-engine inlet centerbody show comparable results.

Rose, W. C.↗
NASA NTRS1976

Turbulence model predictions for the inhomogeneous mixing layer

The plane mixing layer between two streams of different densities and velocities is studied using a complete, phenomenological model of turbulence. The model is an extension of that described by Saffman (1974). The properties of similarity solutions are computed, and compared with experimental data. The qualitative dependence on velocity ratio, density ratio, compressibility and adverse pressure gradient is predicted correctly. The quantitative agreement is satisfactory.

Milinazzo, F.↗
NASA NTRS1976

Inlets for high angles of attack

Different inlet designs for high angle of attack STOL and VTOL applications were tested in a subsonic wind tunnel. Three removable entry lips having contraction ratios of 1.30, 1.34 and 1.38 were tested with a single diffuser. The internal contour of each entry lip was an ellipse with a major to minor axis of 2.0. Each lip and diffuser assembly was tested to determine its tolerance to angle of attack, first with a conventional centerbody and then with an extended centerbody. Results indicate that a large improvement in separation angle (determined as a function of lip contraction ratio and inlet flow) was obtained for the extended centerbody for all contraction ratios. Improved inlet tolerance to angle of attack was obtained by reducing the adverse pressure gradient downstream of the throat.

Miller, B. A.↗