Search NASA⌕ Search

SEARCH · Search NASA

Results for “Aerodynamic design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Aerodynamic design guidelines and computer program for estimation of subsonic wind tunnel performance

General guidelines are given for the design of diffusers, contractions, corners, and the inlets and exits of non-return tunnels. A system of equations, reflecting the current technology, has been compiled and assembled into a computer program (a user's manual for this program is included) for determining the total pressure losses. The formulation presented is applicable to compressible flow through most closed- or open-throat, single-, double-, or non-return wind tunnels. A comparison of estimated performance with that actually achieved by several existing facilities produced generally good agreement.

Eckert, W. T.↗
NASA NTRS1977

Reduced truck fuel consumption through aerodynamic design

Full-scale fuel consumption and drag tests were performed on a conventional cab-over-engine tractor-trailer combination and a version of the same vehicle with significant forebody modifications. The modified configuration had greatly increased radii on all front corners and edges of the tractor and a smooth fairing of the modified tractor top and sides extending to the trailer. Concurrent highway testing of the two configurations showed that the modified design used 20% to 24% less fuel than the baseline configuration at 88.5 km/hr (55 mph) with near-calm wind conditions. Coastdown test results showed that the modified configuration reduced the drag coefficient by 0.43 from the baseline value of 1.17 at 88.5 km/hr (55 mph) in calm wind conditions.

Steers, L. L.↗
NASA NTRS1980

Aerodynamic design optimization of a fuel efficient high-performance, single-engine, business airplane

A design study has been conducted to optimize a single-engine airplane for a high-performance cruise mission. The mission analyzed included a cruise speed of about 300 knots, a cruise range of about 1300 nautical miles, and a six-passenger payload (5340 N (1200 lb)). The purpose of the study is to investigate the combinations of wing design, engine, and operating altitude required for the mission. The results show that these mission performance characteristics can be achieved with fuel efficiencies competitive with present-day high-performance, single- and twin-engine, business airplanes. It is noted that relaxation of the present Federal Aviation Regulation, Part 23, stall-speed requirement for single-engine airplanes facilitates the optimization of the airplane for fuel efficiency.

Holmes, B. J.↗
NASA NTRS1980

Numerical optimization - An assessment of its role in transport aircraft aerodynamic design through a case study

An efficient transonic wing design procedure based upon numerical optimization together with three-dimensional transonic methods has been developed and used to design an advanced transport wing. The method development included an examination of the use of both full potential and extended small disturbance analysis codes and demonstrated that the former formulation was more reliable. In either case, the design procedure is economical and easy to use. Design verification in a unique semi-span test arrangement demonstrated that the design method produced a wing which satisfied the study design requirements. However, aeroelastic deformation of the wing occurred during the wind tunnel test. The computational methods used in the design procedure were employed to assess the effect of the aeroelastic deformation. The paper concludes with an evaluation of the design procedure and recommendation for its improvement.

Lores, M. E.↗
NASA NTRS1980

Computerized three-dimensional aerodynamic design of a lifting rotor blade

A three-dimensional, inviscid, full-potential lifting rotor code was used to demonstrate that pressure distributions on both advancing and retreating blades could be significantly improved by perturbing local airfoil sections. The perturbations were described by simple geometric shape functions. To illustrate the procedure, an example calculation was made at a forward flight speed of 85 m/sec (165 knots) and an advance ratio of 0.385. It was found that a minimum of three shape functions was required to improve the pressures without producing undesirable secondary effects in high-speed forward flight on a hypothetical modern rotor blade initially having an NLR-1 supercritical airfoil. Reductions in the shock strength on the advancing blade could be achieved, while simultaneously lessening leading-edge pressure gradients on the retreating blade. The major blade section modifications required were blunting of the upper surface leading edge and some reshaping of the blade's upper surface resulting in moderately thicker airfoils.

Tauber, M. E.↗
NASA NTRS1983

Aerodynamic design for improved maneuverability by the use of three-dimensional transonic theory

This study has examined the level of transonic maneuver performance that can be achieved by the use of three-dimensional transonic theory. The FLO-27 code of Jameson and Caughey (1977) was used to lower maneuver drag by the reduction of shock strength on the wing upper surface. A design procedure was used to provide a set of guidelines for the iterative application of FLO-27 during the wing design process. The fighter configuration utilized had a leading-edge sweep of 45 deg and an aspect ratio of 3.28. Tests were conducted at Mach numbers from 0.60 to 0.95 and angles of attack from -5 to 18 deg. The accurate prediction of wing shock systems required the inclusion of fuselage effects in the theory. The FLO-27 code gave a reasonable estimate of the experimental wing pressure distributions at transonic maneuver conditions in the region of the wing where the flow was attached. For Mach numbers between 0.60 and 0.95 and lift coefficients near 0.9, a wing designed by the use of FLO-27 showed substantially lower drag than an empirically developed, supercritical maneuver wing and a maneuver wing designed primarily by two-dimensional transonic theory. For some maneuver conditions, the drag of the two-dimensional design was somewhat lower.

Mann, M. J.↗
NASA NTRS1983

Computational aerodynamic design methodology

The transonic wing design process has been vastly improved at Lockheed-Georgia. The revised design procedure enhances useability and reliability by combining numerical optimization and inverse design into a single wing design code with transonic analysis provided by a modified version of FLO22. A more versatile set of geometric decision variables has been integrated into the optimization portion for geometry perturbations. An automatic restart feature permits the interchangeability of solutions between optimization and inverse design as the design progresses. In combination, these improvements enable practical utilization of a VAX 11/780 computer and significantly reduce the elapsed time required to complete a transonic wing design.

Burris, C. B.↗
NASA NTRS1984

Aerodynamic design for improved manueverability by use of three-dimensional transonic theory

Improvements in transonic maneuver performance by the use of three-dimensional transonic theory and a transonic design procedure were examined. The FLO-27 code of Jameson and Caughey was used to design a new wing for a fighter configuration with lower drag at transonic maneuver conditions. The wing airfoil sections were altered to reduce the upper-surface shock strength by means of a design procedure which is based on the iterative application of the FLO-27 code. The plan form of the fighter configuration was fixed and had a leading edge sweep of 45 deg and an aspect ratio of 3.28. Wind-tunnel tests were conducted on this configuration at Mach numbers from 0.60 to 0.95 and angles of attack from -2 deg to 17 deg. The transonic maneuver performance of this configuration was evaluated by comparison with a wing designed by empirical methods and a wing designed primarily by two-dimensional transonic theory. The configuration designed by the use of FLO-27 had the same or lower drag than the empirical wing and, for some conditions, lower drag than the two-dimensional design. From some maneuver conditions, the drag of the two-dimensional design was somewhat lower.

Mann, M. J.↗
NASA NTRS1985

Optimization methods applied to the aerodynamic design of helicopter rotor blades

This paper describes a formal optimization procedure for helicopter rotor blade designs which minimizes hover horsepower while assuring satisfactory forward flight performance. The approach is to couple hover and forward flight analysis programs with a general purpose optimization procedure. The resulting optimization system provides a systematic evaluation of the rotor blade design variables and their interaction, thus reducing the time and cost of designing advanced rotor blades. The paper discusses the basis for and details of the overall procedure, describes the generation of advanced blade designs for representative Army helicopters, and compares designs and design effort with those from the conventional approach which is based on parametric studies and extensive cross-plots.

Walsh, J. L.↗
NASA NTRS1985

Aerodynamic design considerations for efficient high-lift supersonic wings

A previously developed technique for selecting a design space for efficient supersonic wings is reviewed; this design-space concept is expanded to include thickness and camber effects and is evaluated for cambered wings at high-lift conditions. The original design-space formulation was based on experimental upper-surface and lower-surface normal-force characteristics for flat, uncambered delta wings; it is shown that these general characteristics hold for various thickness distributions and for various amounts of leading-edge camber. The original design-space formulation was also based on the assumption that the combination of Mach number and leading-edge sweep which would produce an equal division of flat-wing lift between the upper and lower surface would also be the proper combination to give the best cambered-wing performance. Using drag-due-to-lift factor as a measure of performance, for high-lift conditions cambered-wing performance is shown to significantly increase as conditions approach the design space; this correlation is demonstrated for both subcritical and supercritical flows.

Miller, D. S.↗
NASA NTRS1984

Application of numerical optimization to rotor aerodynamic design

Based on initial results obtained from the performance optimization code, a number of observations can be made regarding the utility of optimization codes in supporting design of rotors for improved performance. (1) The primary objective of improving the productivity and responsiveness of current design methods can be met. (2) The use of optimization allows the designer to consider a wider range of design variables in a greatly compressed time period. (3) Optimization requires the user to carefully define his problem to avoid unproductive use of computer resources. (4) Optimization will increase the burden on the analyst to validate designs and to improve the accuracy of analysis methods. (5) Direct calculation of finite difference derivatives by the optimizer was not prohibitive for this application but was expensive. Approximate analysis in some form would be considered to improve program response time. (6) Program developement is not complete and will continue to evolve to integrate new analysis methods, design problems, and alternate optimizer options.

Pleasants, W. A., III↗
NASA NTRS1985

Nonlinear potential analysis techniques for supersonic aerodynamic design

A numerical method based on the conservation form of the full potential equation has been applied to the problem of three-dimensional supersonic flows with embedded subsonic regions. The governing equation is cast in a nonorthogonal coordinate system, and the theory of characteristics is used to accurately monitor the type-dependent flow field. A conservative switching scheme is employed to transition from the supersonic marching procedure to a subsonic relaxation algorithm and vice versa. The newly developed computer program can handle arbitrary geometries with fuselage, canard, wing, flow through nacelle, vertical tail and wake components at combined angles of attack and sideslip. Results are obtained for a variety of configurations that include a Langley advanced fighter concept with fuselage centerline nacelle, Rockwell's Advanced Tactical Fighter (ATF) with wing mounted nacelles, and the Shuttle Orbiter configuration. Comparisons with available experiments were good.

Shankar, V.↗
NASA NTRS1987

Optimization methods applied to the aerodynamic design of helicopter rotor blades

Described is a formal optimization procedure for helicopter rotor blade design which minimizes hover horsepower while assuring satisfactory forward flight performance. The approach is to couple hover and forward flight analysis programs with a general-purpose optimization procedure. The resulting optimization system provides a systematic evaluation of the rotor blade design variables and their interaction, thus reducing the time and cost of designing advanced rotor blades. The paper discusses the basis for and details of the overall procedure, describes the generation of advanced blade designs for representative Army helicopters, and compares design and design effort with those from the conventional approach which is based on parametric studies and extensive cross-plots.

Walsh, Joanne L.↗