Search NASA⌕ Search

SEARCH · Search NASA

Results for “Aggregative growth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Soot Formation and Growth in Toluene/Ethylene Combustion Catalyzed by Ruthenium Acetylacetonate

Ruthenium-based compounds are efficient catalysts to enhance combustion performance and suppress soot emission. However, systematic mechanism and in-situ research on reducing soot are rarely addressed. In this study, ruthenium acetylacetonate (Ru(C 5 H 7 O 2 ) 3 , Ru(acac) 3 ) was utilized as the catalyst precursor in different concentration conditions to investigate its impacts on the size, volume, and morphology of the soot particles in the ethylene flames with central toluene injection. The soot particles were detected by in-situ small-angle X-ray scattering (SAXS) and ex-situ transmission electron microscopy (TEM). This study confirms that Ru(acac) 3 can suppress the surface growth for the primary soot particles, but no significant change of the morphology has been discovered for the aggregates. Compared with the undoped flame, the volume of the soot particles in the Ru(acac) 3 -doped flames is lower and the particle size is smaller, indicating a valid inhibition effect of Ru(acac) 3 on the soot emission by affecting its surface growth and oxidation process. In conclusion, despite the remarkable distinction between the undoped and doped flames, no obvious difference is found between the flames with different catalyst concentrations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1989

Observations and numerical simulations of precipitation development is seeded clouds over the Sierra Nevada

The evolution of precipitation in seeded wintertime orographically induced convective and stratiform clouds with embedded convection were studied using in situ observations and particle growth and trajectory models. The particle growth model of Heymsfield embedded in a kinematic flow field representative of the Sierra barrier was used to study the ice particle growth by diffusion, accretion and subsequent fall trajectories. The particles observed by the aircraft were classified into habits. The growth of observed particles were compared with the model predicted evolution. Using the aggregation model of Heymsfield, the observation of formation of aggregates is less than 10 minutes was verified. The key findings of this study are presented.

Prasad, N.↗
NASA NTRS1992

Size effects in models for mechanically-stressed protein crystals and aggregates

As protein aggregates increase in size, they become easier to disrupt mechanically. Using the scaling properties of models proposed to govern protein aggregation, the effect of thermal vibrations and gravity are investigated as deforming forces. For typical protein assemblies made of 30 A proteins, the assembled diameter must remain less than 100-10,000 times the molecular radius to survive in finite thermal and gravity fields. The analysis predicts the following experimental outcomes: (1) reductions in gravitational strain should favor larger protein aggregates; (2) in comparing the aggregate stability of different proteins, the addition of peptide chains should stabilize against thermal strain, but should not affect gravitational strain; (3) critical aggregate sizes should show significant (exponential) sensitivity to cluster geometry, solution preparation and growth conditions. The analysis is extended to consider qualitative size effects in crystal damage during X-ray exposure.

Noever, David A.↗
DOE OSTI2024

Chemically Driven Multistep Crystallization in the Synthesis of Sodium Yttrium Fluoride Via a Porous, Electrochemically Active Intermediate

Two-step crystallization mechanisms based on liquid–liquid phase separations followed by crystallization are commonly observed both in the laboratory and in nature. While this pathway quite often occurs as a result of a chemical reaction, the subsequent nucleation and growth are often considered as separate, discrete events from the reaction itself. We show this mechanism in the aqueous synthesis sodium yttrium fluoride, but by using a combination of experimental techniques and computational modeling, we show an additional step of solid-state chemical diffusion that is essential to the nucleation mechanism. In this system, we observe at least four distinct steps in the crystallization process, including (1) the segregation of aqueous ions into a dense liquid phase, (2) the formation of a metastable amorphous aggregate, (3) the continuous, gradual solid-state diffusion of sodium and fluoride ions into the amorphous aggregate toward a NaYF4 stoichiometry, and (4) the crystallization of a stable cubic sodium yttrium fluoride phase. Unlike previous descriptions of nucleation and growth, we find that the stoichiometry of the final solid phase evolves throughout the crystallization process rather than being determined at the time of the initial separation from solution. Further, this emphasizes that the chemical reaction cannot be assumed to be a separate event from the phase separation and growth, especially in compounds with variable stoichiometry. We also find that the amorphous aggregate that forms prior to the ion incorporation step adopts a porous, gel-like structure, which we isolated and showed to be electrochemically active, allowing for its potential use as a battery anode in lithium and sodium ion batteries, among other potential applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Congestion Management Solutions for Enhanced Distribution System Operations with Aggregated Distribution Grid Resources Providing Grid Services and Market Participation

Microgrids and other aggregations of distribution grid resources (DGRs) are poised to actively participate in electricity markets and provide essential grid services in the coming years. In fact, DGRs already play such a role through behind-the-meter (BTM) demand response programs and small-scale BTM dispatchable generation initiatives. At the same time, the rapid growth of artificial intelligence (AI) and cryptocurrency datacenters imposes significant, often unpredictable, demands on the power distribution system. Aggregated DGRs can serve as flexible resources that help mitigate these pressures by using available transmission and distribution capacity more efficiently, supporting resource adequacy and other reliability services, and providing bridge strategies while long-term transmission infrastructure is being developed. The impacts this activity will have on distribution networks are not fully understood and could present significant challenges for distribution utilities due to capacity constraints and the need for congestion management. Technical issues include reverse power flow, variability and possible degradation of equipment integrity, voltage violations, and customer power quality concerns. These issues will likely intensify as electricity market operators across the United States implement Federal Energy Regulatory Commission Order 2222 over the next few years.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Why Does Oriented Attachment Produce Low-Dimensional Structures?

Oriented attachment is a nonclassical crystal growth mechanism that frequently leads to the formation of low-dimensional nanocrystals, such as nanowires or nanoplates, as well as intricately branched nanocrystals. This chapter discusses several experimentally observed instances of such structures, as well as theoretical efforts to understand them. Recent molecular-dynamics simulation studies in our group aimed at understanding how oriented attachment could promote the aggregation of Ag nanoplates to produce two-dimensional sheets are highlighted. Here, the mechanism found in this study may extend to other systems for which lowdimensional crystal growth occurs.

36 MATERIALS SCIENCE↗
NASA NTRS1972

The fluid mechanics of thrombus formation

Experimental data are presented for the growth of thrombi (blood clots) in a stagnation point flow of fresh blood. Thrombus shape, size and structure are shown to depend on local flow conditions. The evolution of a thrombus is described in terms of a physical model that includes platelet diffusion, a platelet aggregation mechanism, and diffusion and convection of the chemical species responsible for aggregation. Diffusion-controlled and convection-controlled regimes are defined by flow parameters and thrombus location, and the characteristic growth pattern in each regime is explained. Quantitative comparisons with an approximate theoretical model are presented, and a more general model is formulated.

Source record↗
DOE OSTI2024

Interactions of clathrate hydrate promoters sodium dodecyl sulfate and tetrahydrofuran investigated using 1H diffusion nuclear magnetic resonance at hydrate-forming conditions

Thermodynamic hydrate promoters and kinetic hydrate promoters can be used to reduce the P–T conditions for clathrate hydrate synthesis to decrease the nucleation induction time while increasing growth rates. Two commonly used promoters for hydrate research are tetrahydrofuran (THF) and sodium dodecyl sulfate (SDS), which can increase the overall hydrate promotion when used in tandem as compared to individually. There are several molecular theories regarding how SDS promotes hydrate growth. This study explores the micellular theory, for which hydrate formation depends on surfactant aggregates (micelles) at a critical micelle concentration (CMC) to increase the interfacial surface area. The micellular theory is the most investigated and criticized surfactant hydrate promotion theory. To address questions related to micellar behavior, this study investigates the intermolecular behavior between SDS and THF for the identification of micelles at hydrate-forming conditions. The systems explored contained THF at 3 and 5 wt. % with varying concentrations of SDS below and above the CMC. Several methods including a qualitative visual method, conductivity, interfacial tensiometry, 13C Liquid-state Nuclear Magnetic Resonance (NMR) spectroscopy, and 1H diffusion NMR spectroscopy were evaluated at temperatures below the Krafft point of SDS and above 0 °C. The presence of THF at low concentrations decreased the critical temperature for the formation of SDS micelles, where SDS is solubilized in THF/water solution at hydrate-forming temperatures without precipitation. The CMC of SDS was decreased significantly even at hydrate-forming conditions. Mixed surfactant–cosolvent micellular behavior of SDS in the presence of low concentrations of THF was confirmed at hydrate-forming conditions above 0 °C.

Chemistry↗
NASA NTRS2007

Observed Enhancement of Reflectivity and Electric Field in Long-Lived Florida Anvils

A study of two long-lived Florida anvils showed that reflectivity greater than 20 dBZ increased in area, thickness and sometimes magnitude at mid-level well downstream of the convective cores. In these same regions electric fields maintained strengths greater than 10 kV m(sup -1) for many tens of minutes and became quite uniform over tens of kilometers. Millimetric aggregates persisted at 9 to 10 km for extended times and distances. Aggregation of ice particles enhanced by strong electric fields might have contributed to reflectivity growth in the early anvil, but is unlikely to explain observations further out in the anvil. The enhanced reflectivity and existence of small, medium and large ice particles far out into the anvil suggest that an updraft was acting, perhaps in weak convective cells formed by instability generated from the evaporation and melting of falling ice particles. We conclude that charge separation must have occurred in these anvils, perhaps at the melting level but also at higher altitudes, in order to maintain fields greater than 10 kV m(sup -1) at 9 to 10 km for extended periods of time over large distances. We speculate that charge separation occurred as a result of ice-ice particle collisions (without supercooled water being present) via either a noninductive or perhaps even an inductive mechanism, given the observed broad ice particle spectra, the strong pre-existing electric fields and the many tens of minutes available for particle interactions. The observations, particularly in the early anvil, show that the charge structure in these anvils was quite complex.

Dye, James E.↗
NASA NTRS2007

Observed Enhancement of Reflectivity and Electric Field in Long-Lived Florida Anvils

A study of two long-lived Florida anvils showed that reflectivity >20 dBZ increased in area, thickness and sometimes magnitude at mid-level well downstream of the convective cores. In these same regions electric fields maintained strengths >10 kV m1 for many tens of minutes and became quite uniform over tens of kilometers. Millimetric aggregates persisted at 9 to 10 km for extended times and distances. Aggregation of ice particles enhanced by strong electric fields might have contributed to reflectivity growth in the early anvil, but is unlikely to explain observations further out in the anvil. The enhanced reflectivity and existence of small, medium and large ice particles far out into the anvil suggest that an updraft was acting, perhaps in weak convective cells formed by instability generated from the evaporation and melting of falling ice particles. We conclude that charge separation must have occurred in these anvils, perhaps at the melting level but also at higher altitudes, in order to maintain fields >10 kV m 1 at 9 to 10 km for extended periods of time over large distances. We speculate that charge separation occurred as a result of ice-ice particle collisions (without supercooled water being present) via either a non-inductive or perhaps even an inductive mechanism, given the observed broad ice particle spectra, the strong pre-existing electric fields and the many tens of minutes available for particle interactions. The observations, particularly in the early anvil, show that the charge structure in these anvils was quite complex.

Dye, James E.↗
NASA NTRS2020

A Composite Analysis of Snowfall Modes from Four Winter Seasons in Marquette, Michigan

Presented are four winter seasons of data from an enhanced precipitation instrument suite based at the National Weather Service (NWS) Office in Marquette (MQT), Michigan (250–500 cm of annual snow accumulation). In 2014 the site was augmented with a Micro Rain Radar (MRR) and a Precipitation Imaging Package (PIP). MRR observations are utilized to partition large-scale synoptically driven (deep)and surface-forced (shallow) snow events. Coincident PIP and NWS MQT meteorological surface observations illustrate different characteristics with respect to snow event category. Shallow snow events are often extremely shallow, with MRR-indicated precipitation heights of less than 1500 m above ground level. Large vertical reflectivity gradients indicate efficient particle growth, and increased boundary layer turbulence inferred from observations of spectral width implies increased aggregation in shallow snow events. Shallow snow events occur 2 times as often as deep events; however, both categories contribute approximately equally to estimated annual accumulation. PIP measurements reveal distinct regime-dependent snow microphysical differences, with shallow snow events having broader particle size distributions and comparatively fewer small particles and deep snow events having narrower particle size distributions and comparatively more small particles. In addition, coincident surface meteorological measurements indicate that most shallow snow events are associated with surface winds originating from the northwest (over Lake Superior), cold temperatures, and relatively high surface pressures, which are characteristics that are consistent with cold-air outbreaks. Deep snow events have meteorologically distinct conditions that are accordant with midlatitude cyclones and frontal structures, with mostly southwest surface winds, warmer temperatures approaching freezing, and lower surface pressures.

Claire Pettersen↗
DOE OSTI2021

Decreased growth of wild soil microbes after 15 years of transplant‐induced warming in a montane meadow

Abstract The carbon stored in soil exceeds that of plant biomass and atmospheric carbon and its stability can impact global climate. Growth of decomposer microorganisms mediates both the accrual and loss of soil carbon. Growth is sensitive to temperature and given the vast biological diversity of soil microorganisms, the response of decomposer growth rates to warming may be strongly idiosyncratic, varying among taxa, making ecosystem predictions difficult. Here, we show that 15 years of warming by transplanting plant–soil mesocosms down in elevation, strongly reduced the growth rates of soil microorganisms, measured in the field using undisturbed soil. The magnitude of the response to warming varied among microbial taxa. However, the direction of the response—reduced growth—was universal and warming explained twofold more variation than did the sum of taxonomic identity and its interaction with warming. For this ecosystem, most of the growth responses to warming could be explained without taxon‐specific information, suggesting that in some cases microbial responses measured in aggregate may be adequate for climate modeling. Long‐term experimental warming also reduced soil carbon content, likely a consequence of a warming‐induced increase in decomposition, as warming‐induced changes in plant productivity were negligible. The loss of soil carbon and decreased microbial biomass with warming may explain the reduced growth of the microbial community, more than the direct effects of temperature on growth. These findings show that direct and indirect effects of long‐term warming can reduce growth rates of soil microbes, which may have important feedbacks to global warming.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Tracking nanoparticle growth in pulsed carbon arc discharge

The dynamics of nanoparticle growth in pulsed anodic arc discharge has been studied in time-resolved mode. To this end, a fast moving probe was employed to extract the material generated in a pulsed arc plasma held between two graphite electrodes. The probe motion was synchronized with the pulse phase and the exposure time to the plasma was set to 10 ms. The graphite anode was eroded in a helium atmosphere (300 Torr) by an arc plasma pulsed at 1 Hz with a 10% duty cycle and showing 250 A of peak current. The structure and morphology of the probe depositions were characterized by Raman spectroscopy, scanning electron microscopy, and focused ion beam. A maximal deposition rate of 260 μm/s was measured 5 mm away from the arc core during the active 0.1 s of the pulse. Such a rate yields a growth flux of 1.3 × 10 21 cm –2 s –1 , rich in carbon nanostructures (graphene platelets, nanotubes) with a characteristic aggregate size within 1–10 μm. The deposition during the inactive 0.9 s of the pulse was several orders of magnitude slower and consisted of amorphous carbon traces. Furthermore, the nanoparticle distribution along the collecting probe is correlated with the pulse phase, thereby providing information on particle transport. Pulsed nanosynthesis can be modeled as a periodical growth process, where the volume and propagation velocity of the growth region can be adjusted through modulation of the pulse signal waveform. The proposed model constitutes a suitable framework to investigate the pulsed arc synthesis of nanomaterials with tailored physical and chemical properties.

42 ENGINEERING↗
DOE OSTI2021

Kinetically Controlled Formation of Semi-crystalline Conjugated Polymer Nanostructures

Conjugated polymer (CP) materials that are considered as an attractive choice for various electronic and optoelectronic applications possess highly heterogeneous complex structures that can span several orders of magnitude in length scale. This is due to the intricate coupling effects of weak secondary interactions and entropic forces that determine molecular organization in bulk polymer materials. Understanding the influence of molecular interactions on the emergence and evolution of nano- and microscale structures is of paramount importance to the guided design and development of condensed CP materials. Such understanding is even more critical for the rational design of hierarchical systems away from equilibrium, where weak molecular interactions can guide the system along competing kinetic pathways toward local energy minima and metastable architectures. In this work, we studied a promising concept for accessing various kinetically stabilized semi-crystalline CP nanostructures that are formed in the process of controlled chain-growth Kumada catalyst-transfer polymerization initiated by a small-molecule catalytic species which can exist in equilibrium between free and aggregated states. Specifically, we chose a small-molecule perylenedicarboximide (PDCI) polymerization catalytic initiator which has a strong tendency toward reversible supramolecular assembly–disassembly that can be controlled by temperature. Addition of a thiophene monomer to a solution of the PDCI initiator starts the chain-growth polymerization process, which produces distinct nanoscale semi-crystalline polythiophene structures formed under predominant kinetic control. Furthermore, we demonstrated that, depending on the reaction temperature (which affects the fine balance between the position of PDCI assembly–disassembly equilibrium, rate of polymerization, and solvent–solute interactions for the growing polythiophene chains), a range of kinetically trapped hierarchically organized semi-crystalline CP systems with substantially varying optoelectronic properties could be obtained. In addition to spectroscopic and electron microscopic studies, in order to better reveal the structural aspects of the generated polymer nanoscale systems, we carried out a series of X-ray diffraction and neutron scattering experiments which indicated complex hierarchical organization in these kinetically stabilized CP assembled materials. We expect that this in situ polymerization-based approach can lead to a general way to expand access to various semi-crystalline CP nanostructured materials with broadly tunable electronic and optical properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1991

Sintering of two phase lamellar microstructures

The effect of an inert phase on neck growth rates during sintering of lamellar structures is described. Sintering diagrams are constructed for an aggregate of two-phase Cu spheres with lamellar microstructure containing an inert phase. It is shown that the regions corresponding to lattice diffusion domination shrink due to the inert phase presence. As the dispersion becomes finer, the alterations in the map become substantial.

Courtney, T. H.↗
NASA NTRS1996

Nucleation and Crystallization of Globular Proteins: What we Know and What is Missing

Recently. much progress has been made in understanding the nucleation and crystallization of globular proteins, including the formation of compositional and structural crystal defects, Insight into the interactions of (screened) protein macro-ions in solution, obtained from light scattering, small angle X-ray scattering and osmotic pressure studies. can guide the search for crystallization conditions. These studies show that the nucleation of globular proteins is governed by the same principles as that of small molecules. However, failure to account for direct and indirect (hydrodynamic) protein interactions in the solutions results in unrealistic aggregation scenarios. Microscopic studies of numerous proteins reveal that crystals grow by the attachment of growth units through the same layer-spreading mechanisms as inorganic crystals. Investigations of the growth kinetics of hen-egg-white lysozyme (HEWL) reveal non-steady behavior under steady external conditions. Long-term variations in growth rates are due to changes in step-originating dislocation groups. Fluctuations on a shorter timescale reflect the non-linear dynamics of layer growth that results from the interplay between interfacial kinetics and bulk transport. Systematic gel electrophoretic analyses suggest that most HEWL crystallization studies have been performed with material containing other proteins at percent levels. Yet, sub-percent levels of protein impurities impede growth step propagation and play a role in the formation of structural/compositional inhomogeneities. In crystal growth from highly purified HEWL solutions, however, such inhomogeneities are much weaker and form only in response to unusually large changes in growth conditions. Equally important for connecting growth conditions to crystal perfection and diffraction resolution are recent advances in structural characterization through high-resolution Bragg reflection profiling and X-ray topography.

Rosenberger, F.↗
NASA NTRS1999

Soot Aerosol Properties in Laminar Soot-Emitting Microgravity Nonpremixed Flames

The spatial distributions and morphological properties of the soot aerosol are examined experimentally in a series of 0-g laminar gas-jet nonpremixed flames. The methodology deploys round jet diffusion flames of nitrogen-diluted acetylene fuel burning in quiescent air at atmospheric pressure. Full-field laser-light extinction is utilized to determine transient soot spatial distributions within the flames. Thermophoretic sampling is employed in conjunction with transmission electron microscopy to define soot microstructure within the soot-emitting 0-g flames. The microgravity tests indicate that the 0-g flames attain a quasi-steady state roughly 0.7 s after ignition, and sustain their annular structure even beyond their luminous flame tip. The measured peak soot volume fractions show a complex dependence on burner exit conditions, and decrease in a nonlinear fashion with decreasing characteristic flow residence times. Fuel preheat by approximately 140 K appears to accelerate the formation of soot near the flame axis via enhanced fuel pyrolysis rates. The increased soot presence caused by the elevated fuel injection temperatures triggers higher flame radiative losses, which may account for the premature suppression of soot growth observed along the annular region of preheated-fuel flames. Electron micrographs of soot aggregates collected in 0-g reveal the presence of soot precursor particles near the symmetry axis at midflame height, The observations also verify that soot primary particle sizes are nearly uniform among aggregates present at the same flame location, but vary considerably with radius at a fixed distance from the burner. The maximum primary size in 0-g is found to be by 40% larger than in 1-g, under the same burner exit conditions. Estimates of the number concentration of primary particles and surface area of soot particulate phase per unit volume of the combustion gases are also made for selected in-flame locations.

Konsur, Bogdan↗
NASA NTRS2011

Monitoring Crop Yield in USA Using a Satellite-Based Climate-Variability Impact Index

A quantitative index is applied to monitor crop growth and predict agricultural yield in continental USA. The Climate-Variability Impact Index (CVII), defined as the monthly contribution to overall anomalies in growth during a given year, is derived from 1-km MODIS Leaf Area Index. The growing-season integrated CVII can provide an estimate of the fractional change in overall growth during a given year. In turn these estimates can provide fine-scale and aggregated information on yield for various crops. Trained from historical records of crop production, a statistical model is used to produce crop yield during the growing season based upon the strong positive relationship between crop yield and the CVII. By examining the model prediction as a function of time, it is possible to determine when the in-season predictive capability plateaus and which months provide the greatest predictive capacity.

Zhang, Ping↗