SEARCH · Search NASA

Results for “Alloy 625”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Influence of gaseous hydrogen on metals

Tensile, fracture toughness, threshold stress intensity for sustained-load crack growth, and cyclic and sustained load crack growth rate measurements were performed on a number of alloys in high-pressure hydrogen and helium environments. The results of tensile tests performed in 34.5 MN/m2 (5000 psi) hydrogen indicated that Inconel 625 was considerable embrittled at ambient temperature but was not embrittled at 144 K (-200 F). The tensile properties of AISI 321 stainless steel were slightly reduced at ambient temperature and 144 K (-200 F). The tensile properties of Ti-5Al-2.5 Sn ELI were essentially unaffected by hydrogen at 144 K (-200 F). OFHC copper was not embrittled by hydrogen at ambient temperature or at 144 K (-200 F).

Walter, R. J.↗

NASA NTRS1991

The effect of TiB2 reinforcement on the mechanical properties of an Al-Cu-Li alloy-based metal-matrix composite

The addition of ceramic particles to aluminum based alloys can substantially improve mechanical properties, especially Young's modulus and room and elevated temperature strengths. However, these improvements typically occur at the expense of tensile ductility. The mechanical properties are evaluated to a metal matrix composite (MMC) consisting of an ultrahigh strength aluminum lithium alloy, Weldalite (tm) 049, reinforced with TiB2 particles produced by an in situ precipitation technique called the XD (tm) process. The results are compared to the behavior of a nonreinforced Weldalite 049 variant. It is shown that both 049 and 049-TiB2 show very attractive warm temperature properties e.g., 625 MPa yield strength at 150 C after 100 h at temperature. Weldalite 049 reinforced with a nominal 4 v pct. TiB2 shows an approx. 8 pct. increase in modulus and a good combination of strength (529 MPa UTS) and ductility (6.5 pct.) in the T3 temper. And the high ductility of Weldalite 049 in the naturally aged and underaged tempers makes the alloy a good, high strength matrix for ceramic reinforcement.

Source record↗

DOE OSTI2024

Strength-ductility synergy through microstructural and compositional heterogeneity in directed energy deposition additive manufacturing of face-centered cubic materials

Directed energy deposition (DED) is an additive manufacturing (AM) process based on welding technology and offers the advantages of large build volume, high deposition rate, and ability to fabricate multi-material parts. Epitaxial continuous columnar grain growth is a characteristic microstructural feature of DED processed alloys. In this study, a bamboo-like microstructure (periodic alternation of equiaxed and columnar structure) was produced by adopting an intermittent deposition strategy in 316L stainless steel and Inconel 625. The formation of a bamboo-like alternating microstructure was confirmed through electron backscattered diffraction (EBSD) analysis. Hardness mapping showed that the columnar to equiaxed transition (CET) occurred at the region right below the fusion line. A finite element (FE) model was used to investigate the relationship between the temperature gradient (G) and the solidification rate (R). The FE model showed a low G/R ratio at the region right below the interface promoting the CET. The grain size and material-dependent deformation behaviors are analyzed using digital image correlation (DIC). The lower deformation on the fine-grain regions observed in DIC analysis is attributed to a higher strain hardening rate, which is confirmed through dislocation density analysis on a tensile-interrupted specimen. The periodically alternating grain size coupled with the microstructural changes caused by intermittent deposition strategy result in a better strength-ductility synergy in both single-material and bimetallic specimens.

36 MATERIALS SCIENCE↗

DOE OSTI2023

High Temperature Ternary Chloride Molten Salt Pump

This work investigates the design criteria considering thermal, structural, and material selection of a ternary chloride (MgCl2-NaCl-KCl) molten salt pump that is capable of running at temperatures above 720 °C. In this work, preliminary testing of salt-wetted hydrodynamic bearings was done to investigate different material pairings including Colmonoy grades, Stellite grades, and a novel Nickel Tungsten Carbide alloy (HybrimetTM NiWC3b) used as a High Velocity Oxygen Fuel (HVOF) coating. The coating has shown to withstand the corrosive nature of the molten salt. The pump wetted components are made of Inconel 625 and features a carbon ring seal (CIRPAC Seal) flooded with a N2 gas flow on the overhead to keep salt vapors from interacting with the external ambient air. A comprehensive pump test program has been completed. Over 90 hours run time pumping hot chloride salts at temperatures up to 720 °C in which enough data was captured to produce performance curves at 3 different operating speeds. This research showcases a promising design for use in the Concentrated Solar Power (CSP) Gen 3 liquid-pathway and sets the ground for further development and use of the HybrimetTM NiWC3b as a competitive alternative to available superalloys.

14 SOLAR ENERGY↗

NASA NTRSDate not supplied

Advancing GRCop-based Bimetallic Additive Manufacturing to Optimize Component Design and Applications for Liquid Rocket Engines

Additive manufacturing (AM) is advancing many applications of component design for liquid rocket engines. The ability to rapidly design and manufacture components has provided significant opportunities for development and flight programs across the propulsion industry. AM has demonstrated significant advantages that include cost and schedule savings in addition to performance improvements through new design opportunities. While these performance advantages can be in the characteristics of complex design features, they can also be in the form of new materials. AM has been demonstrated in these various component applications using a variety of metal alloys, many of which are traditional alloys for extreme environments. Additional developments were completed using AM to provide new alloys and maturing these material uses for high performance applications. Almost all of the prior developments across component applications have focused on single-alloys in these AM processes. NASA and industry partners have focused in recent years to advance processing to create bimetallic and multicomponent AM processes and materials. The role of multi-alloy AM offers advantages since it can further optimize weight, optimize reliability and performance by increasing the strength to weight ratio of a component, and can optimize materials for various engineering requirements. This is particularly important in liquid rocket engine combustion devices that must reject heat in high heat flux environments yet maintain adequate structural margins under high operational pressure. NASA has been exploring several AM processes, materials, and applications for combustion devices, specifically combustion chambers, injectors, nozzles, and ignition systems. These components require fine geometric features for internal flow or cooling functionality. They experience high thermal gradients across thin-walls and must survive high pressures and temperatures from propellants and the combustion process. A copper-based alloy is normally used to provide high thermal conductivity, but at the detriment of increased weight if used as a single alloy in an AM chamber. Various AM processes were demonstrated on these components using a copper-based alloy/superalloy bimetallic solution. The AM processes being explored individually and in combination for bimetallic applications include Laser Powder Bed Fusion (L-PBF), Laser Powder Directed Energy Deposition (LP-DED), and cold spray. The combination of bimetallic material combinations explored in this research include copper-based material primarily and superalloys, Inconel 625 or NASA HR-1. The various aspects of the additive manufacturing processes and challenges, materials characterization, and the testing of bimetallic components in a relevant environment will be discussed.

Additive Manufacturing↗

NASA NTRS2018

ECLSS Universal Waste Management System (UWMS) Metal Materials Compatibility Study - Elgiloy: Electrochemical and Crevice Corrosion Evaluation

Electrochemical evaluations were conducted on samples of Elgiloy in support of the materials compatibility program for the Environmental Control and Life Support System (ECLSS). Results were compared alongside three previously tested metals: Titanium 6Al-4V, Inconel 625, and Hastelloy C276. Titanium exhibited the best results of all the metals, indicating superior corrosive nobility and galvanic protection properties. Elgiloy demonstrated anti-corrosion behavior which appeared to be superior to the two nickel-chromium alloys. For this current effort, the results have clearly shown that Elgiloy possesses excellent corrosion protection properties and is galvanically compatible with the other three metals in the subject test media.

Lee, R. E.↗

DOE OSTI2024

Radiation-Induced Defect Formation Kinetics in Inconel–Cu Multimetallic Layered Composites

This study investigates the stability of Inconel–Cu Multimetallic Layered Composites (MMLCs) in nuclear reactor applications using Molecular Dynamics simulations. The focus is on understanding the underlying mechanisms governing the properties of MMLCs for advanced nuclear reactors, specifically, the mechanochemistry of the interface between Inconel and copper alloys. The selection of Inconel–Cu MMLCs is primarily due to copper’s superior thermal conductivity, enhancing heat management within reactors by preventing hotspots and ensuring uniform temperature distribution. This research examines Incoloy 800H and two Inconel variants (718 and 625), assessing their stability at 1000 K after exposure to 10 keV collision cascades up to 0.12 dpa. Notable findings include defect clustering on the {1 2 0} family of planes of Inconel and Cu, with Stacking Faults and Lomer–Cottrell locks on the Inconel side.

Ramesh, Rajesh↗

DOE OSTI2023

High Temperature Ternary Chloride Molten Salt Pump

A ternary chloride (MgCl2-NaCl-KCl) molten salt pump has been developed to operate up to 720°C. The design is the result of a thermal, structural and material study of critical components. The vertical overhung pump incorporates first of a kind salt-wetted hydrodynamic bearings. Several bearing material pairings were tested which include: colmonoy grades, stellite grades, and a novel NiWC-based alloy (i.e. HybrimetTM NiWC3b) used as a High Velocity Oxygen Fuel (HVOF) coating. The coating withstands the corrosion effects of the molten salt, and is also used to protect a 316L stainless steel pump reservoir. The pump bowl assembly components are made of Inconel 625. A Nitrogen flushed carbon ring seal is used to keep salt vapors from interacting with external ambient air. Preliminary testing shows a promising pump design for use in the Concentrating Solar Power Gen 3 systems and sets the ground for further development of the HybrimetTM NiWC3b as a competitive alternative to available superalloys.

Handy-Cardenas, Lewis (ORCID:0009000744006972)↗

DOE OSTI2022

High Temperature Ternary Chloride Molten Salt Pump

This work investigates the design criteria considering thermal, structural, and mate-rial selection of a ternary chloride (MgCl2-NaCl-KCl) molten salt pump that is capable of running at temperatures above 720 °C. In this work, preliminary testing of salt-wetted hydrodynamic bearings was done to investigate different material pairings including colmonoy grades, stellite grades, and a novel NiWC-based alloy (i.e. HybrimetTM NiWC3b) used as a High Velocity Ox-ygen Fuel (HVOF) coating. The coating has shown to withstand the corrosive nature of the salt, and is additionally used to protect a 316L stainless steel pump reservoir. The pump wetted components are made of Inconel 625, and it features a carbon ring seal developed by Flows-erve flooded with a N2 gas flow on the overhead to keep salt vapors from interacting with the external ambient air. This research showcases a promising design for use in the CSP Gen 3 liquid-pathway and sets the ground for further development and use of the HybrimetTM NiWC3b as a competitive alternative to available superalloys. Further work will further characterize the pump by performance & cycle testing in molten salt at higher temperatures.

14 SOLAR ENERGY↗

DOE OSTI2022

Grain size effect on corrosion behavior of Inconel 625 film against molten MgCl 2 -NaCl-KCl salt

This study evaluated the grain size effect of Inconel 625 film against molten chloride salt. It is found that larger grain size Inconel 625 exhibits better corrosion resistance by reducing Cr depletion. ~ 2 nm surface NiO layer of Inconel 625 is incapable of compensating the negative effects from more initiation corrosion sites. Mo is the least likely leached element and its enrichment occurs in Cr-depleted regions as a result of Mo diffusion. Mg and Cl are two most seen salt elements in all corroded samples, while K and Na only attack Inconel 625 with the smallest grain size.

14 SOLAR ENERGY↗

NASA NTRS1986

Reactions occurring during the sulfation of sodium chloride deposited on alumina substrates

The reaction between solid NaCl and air containing 1 pct SO2 has been studied between 500 and 700 C. The reaction product, Na2SO4, forms not only on the surface of the NaCl but also on surrounding areas of the substrate due to the volatility of the NaCl at these temperatures. At the higher temperatures, the vapor pressure of NaCl is so high that the majority of the reaction product is distributed on the substrate. Above 625 C, the reaction product is a liquid solution of NaCl and Na2SO4 that exists only so long as NaCl is supplied from the original crystal source. Eventually, the liquid solidifies by constitutional solidification as the NaCl is converted to Na2SO4. While it exists, the liquid NaCl-Na2SO4 solution is shown to be highly corrosive to Al2O3 and, on a scale of Al2O3 growing on alloy HOS 875, particularly attacks the grain boundaries of the scale at preferred sites where chromium and iron oxides and sulfides rapidly develop. This is proposed as one mechanism by which NaCl deposition contributes to the initiation of low temperature hot corrosion.

Wu, C. S.↗

DOE OSTI2024

Unveiling the nucleation and growth of Zr oxide precipitates in internally oxidized Nb3Sn superconductors

We report on atomic-scale analyses of nucleation and growth of Zr oxide precipitates and the microstructural evolution of internally oxidized Nb3Sn wires for high-field superconducting magnet applications, utilizing atom probe tomography (APT), transmission electron microscopy (TEM), and first-principles calculations. APT analyses reveal that oxygen and zirconium are already segregated at grain boundaries (GBs) in the unreacted Nb-1Zr-4Ta (at%) alloy prior to forming Nb3Sn through reacting the Nb alloy with Sn and SnO2. After forming Nb3Sn, Zr oxide precipitates nucleate both at the Nb3Sn/Nb heterophase interfaces and in the Nb3Sn grains, driven by the small solubilities of Zr and O in Nb3Sn compared to their value in Nb. A high number density (Nv) of Zr oxide nanoprecipitates is observed in the Nb3Sn layers, ∼10 23 m −3 , with a mean diameter <10 nm for a heat treatment at 625 °C. Quantitative APT and TEM analyses of the Zr oxide precipitates in the reacted Nb3Sn layers elucidate details of the nucleation, growth, and coarsening processes of the Zr oxide precipitates in Nb3Sn. First-principles calculations and classical nucleation theory are employed to study the nucleation of Zr oxide precipitates in Nb3Sn and to estimate the maximum energy barrier and critical radius for nucleation. Our research unveils the kinetic pathways for nucleation and growth of Zr oxide precipitates and the microstructural evolution of Nb3Sn layers, which helps to understand and improve the superconducting properties of internally oxidized Nb3Sn wires for use in high-field superconducting magnets. •We investigated the nucleation and growth of Zr oxide nanoprecipitates in Nb3Sn superconductors for magnet applications.•APT and TEM analyses reveals the nucleation and growth process of Zr oxide precipitates in Nb3Sn layers.•Classical nucleation theory with DFT is employed to describe the nucleation process of Zr oxide precipitates in Nb3Sn.•We find that the interfacial reactions at Nb/Nb3Sn interface play a critical role in the nucleation of Zr oxide precipitates.•Current study provides a pathway to improve the properties of internally oxidized Nb3Sn superconducting wires.

43 PARTICLE ACCELERATORS↗

NASA NTRSDate not supplied

Advancing GRCop-based Bimetallic Additive Manufacturing to Optimize Component Design and Applications for Liquid Rocket Engines

Additive Manufacturing↗

DOE OSTI2024

Dissolution Flowsheet for Non-Aluminum Spent Nuclear Fuel Campaign 1

As part of the Accelerated Basin De-inventory (ABD) program, H Canyon plans to dissolve non-aluminum spent nuclear fuel (NASNF) in the 6.3D electrolytic dissolver. NASNF Campaign 1 plans to electrolytically dissolve 68 bundles of fuel assemblies from the Carolinas-Virginia Tube Reactor (CVTR), Heavy Water Components Test Reactor (HWCTR), and Experimental Boiling Water Reactor (EBWR). The fuel assemblies are intact Zircaloy or stainless steel (SS) clad UO 2 rods, tubes, and plates. The H Canyon electrolytic dissolver previously dissolved a variety of UO 2 core fuel types in SS, Zircaloy, Nichrome, or Incoloy cladding from 1969 to 1980. The objective of this study was to identify flowsheet conditions through literature review and laboratory experimentation to safely dissolve NASNF Campaign 1 bundles in the H Canyon electrolytic dissolver. Bench-scale electrolytic dissolution tests were performed to demonstrate a flowsheet for NASNF Campaign 1 bundles. The outer bundles are composed of SS or Al alloy, Al 6061-T6, and contain intact Zircaloy or SS clad UO 2 fuel assemblies. The key objectives of these tests were to determine bounding dissolver chemistries and the sparge requirement to ensure H 2 concentration remain less than 60 vol % of the lower flammability limit (LFL) during dissolution. The impact of HNO 3 concentration and the addition of fluoride on the dissolution efficiency of Zircaloy, 304L SS, Al 6061-T6, and Inconel 625 were examined. While SS, Al, and Inconel 625 readily dissolve utilizing electrolytic dissolution, Zircaloy disintegrated anodically; the surface of Zircaloy oxidized and the oxide layer spalled off and settled at the bottom of the dissolver as an insoluble material. The black flakes were identified as ZrO 2 and 85% of the Zr processed was converted to black ZrO 2 flakes when Zr was anodically disintegrated in 9.5 M HNO 3 .

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS2021

Benchmarking Surface Tension Measurement Method using two Oscillation Modes in Levitated Liquid Metals

The Faraday forcing method in levitated liquid droplets has recently been introduced as a method for measuring surface tension using resonance. By subjecting an electrostatically-levitated liquid metal droplet to a continuous, oscillatory, electric field, at a frequency nearing that of the droplet’s first principal mode of oscillation (known as mode 2), the method was previously shown to determine surface tension of materials that would be particularly difficult to process by other means, e.g. liquid metals and alloys. It also offers distinct advantages in future work involving high viscosity samples because of the continuous forcing approach. This work presents 1) a benchmarking experimental method to measure surface tension by excitation of the second principal mode of oscillation (known as mode 3) in a levitated liquid droplet and 2) a more rigorous quantification of droplet excitation using a projection method. Surface tension measurements compare favorably to literature values for Zirconium, Inconel 625, and Rhodium, using both modes 2 and 3. Thus, this new method serves as a credible, self-consistent benchmarking technique for the measurement of surface tension

Levitation↗

DOE OSTI2026

Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application

Cold spray deposition of Inconel nickel alloys has emerged as a promising strategy for mitigating cavitation erosion in hydropower facilities. Most prior developments employ helium (He) as the carrier gas because it enables high particle velocities and the formation of dense coatings. However, He is nearly two orders of magnitude more expensive than nitrogen (N2), which limits its widespread adoption in the hydropower sector. Although He-based cold spray can be justified for high value repairs, the lower cost and broad availability of N2 make it an attractive alternative. This study assesses the feasibility of N2-based cold spray of Inconel 625 powders for hydropower applications. Cavitation erosion testing shows that He-based coating exhibits cavitation resistance of ~398% relative to the 304L stainless steel (SS304L) substrate. In contrast, N2-based coating shows substantially lower cavitation resistance, reaching only ~69% of the SS304L substrate, even when higher carrier gas temperature and pressure are applied. When the Inconel 625 powder size is reduced from 44 to 22 µm under N2-based cold spray conditions, cavitation resistance increases significantly to ~148% of the SS304L substrate. Additional improvement can be obtained by incorporating fine chromium carbide powders into the feedstock, resulting in cavitation resistance of ~172% of the SS304L substrate. Overall, with optimized feedstock design, N2-based cold spray offers a practical and cost-effective approach for producing cavitation resistant coatings on hydropower components, although He-based cold spray continues to deliver higher cavitation resistance.

Wang, Tianhao↗

DOE OSTI2023

Combining synchrotron X-ray diffraction, mechanistic modeling and machine learning for in situ subsurface temperature quantification during laser melting

Laser melting, such as that encountered during additive manufacturing, produces extreme gradients of temperature in both space and time, which in turn influence microstructural development in the material. Qualification and model validation of the process itself and the resulting material necessitate the ability to characterize these temperature fields. However, well established means to directly probe the material temperature below the surface of an alloy while it is being processed are limited. To address this gap in characterization capabilities, a novel means is presented to extract subsurface temperature-distribution metrics, with uncertainty, from in situ synchrotron X-ray diffraction measurements to provide quantitative temperature evolution data during laser melting. Temperature-distribution metrics are determined using Gaussian process regression supervised machine-learning surrogate models trained with a combination of mechanistic modeling (heat transfer and fluid flow) and X-ray diffraction simulation. The trained surrogate model uncertainties are found to range from 5 to 15% depending on the metric and current temperature. The surrogate models are then applied to experimental data to extract temperature metrics from an Inconel 625 nickel superalloy wall specimen during laser melting. The maximum temperatures of the solid phase in the diffraction volume through melting and cooling are found to reach the solidus temperature as expected, with the mean and minimum temperatures found to be several hundred degrees less. The extracted temperature metrics near melting are determined to be more accurate because of the lower relative levels of mechanical elastic strains. However, uncertainties for temperature metrics during cooling are increased due to the effects of thermomechanical stress.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Predicting Sintering Window of Binder Jet Additively Manufactured Parts Using a Coupled Data Analytics and CALPHAD Approach

Batch-to-batch variation in powder compositions for binder jet additive manufacturing (BJAM) can significantly deter defining an “ideal” sintering window for a given alloy. One way to overcome the problem is by running sintering experiments at various temperatures for each batch of the powder. However, such an approach increases the time required to achieve large-scale production of parts. The predictive capabilities of computational thermodynamic tools like CALPHAD can be leveraged to overcome the challenge, especially for binder jet additive manufacturing, since the process occurs under near-equilibrium conditions. However, calculating the sintering window using CALPHAD can be computationally expensive, considering many possible feedstock compositions within “specification”. Here, we generate high throughput CALPHAD data for nickel-based superalloys to develop machine learning models to predict the sintering window rapidly. The predictive capability of the models has been validated using published results on BJAM of Inconel 718 and 625. Further, validated models are lightweight and can be deployed in an industrial setting to get sintering window in an accelerated manner.

36 MATERIALS SCIENCE↗