Search NASA⌕ Search

SEARCH · Search NASA

Results for “BEAMS, THIN - WEBS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Properties of large area ErBa2Cu3O(7-x) thin films deposited by ionized cluster beams

ErBa2Cu3O(7-x) films have been produced by simultaneous deposition of Er, Ba, and Cu from three ionized cluster beam (ICB) sources at acceleration voltages of 0.3 to 0.5 kV. Combining ozone oxidation with ICB deposition at 650 C eliminated any need of post annealing processing. The substrates were rotated at 10 rotations per minute during the deposition which took place at a rate of about 3 to 4 nm. Films with areas up to 70 mm in diameter have been made by ICB deposition. These films, 100 nm thick, were deposited on SrTiO3 (100) substrates at 650 C in a mixture of six percent O3 in O2 at a total pressure of 4 x 10(exp -4) Torr. They had T(sub c) ranging from 84.3 K to 86.8 K over a 70 mm diameter and J(sub c) above 10(exp 6) A/sq cm at 77 K. X ray diffraction measurements of the three samples showed preferential c-axis orientation normal to the substrate surface. Scanning electron micrographs (SEM) of the three samples also show some texture dependence on sample position. For the three samples, there is a correlation between SEM texture, full width at half-maximum of rocking curves and J(sub c) versus temperature curves.

Levenson, L. L.↗
NASA NTRS1991

Properties of large area ErBa2Cu3O(7-x) thin films deposited by ionized cluster beams

Ionized cluster beam (ICB) deposition is employed to produce ErBa2Cu3O(7-x) films on different substrates without post-annealing. Films with diameters of up to 70 mm are grown on SrTiO3 100 plane and exhibit Tc values of 84-87 K, Jc of about 10 exp 6 A/sq m at 77 K. These films are epitaxial with the c-axis perpendicular to the plane of the substrate surface, and they can be routinely produced by ICB with good Jc and Tc.

Levenson, L. L.↗
NASA NTRS1996

Development of Multiobjective Optimization Techniques for Sonic Boom Minimization

A discrete, semi-analytical sensitivity analysis procedure has been developed for calculating aerodynamic design sensitivities. The sensitivities of the flow variables and the grid coordinates are numerically calculated using direct differentiation of the respective discretized governing equations. The sensitivity analysis techniques are adapted within a parabolized Navier Stokes equations solver. Aerodynamic design sensitivities for high speed wing-body configurations are calculated using the semi-analytical sensitivity analysis procedures. Representative results obtained compare well with those obtained using the finite difference approach and establish the computational efficiency and accuracy of the semi-analytical procedures. Multidisciplinary design optimization procedures have been developed for aerospace applications namely, gas turbine blades and high speed wing-body configurations. In complex applications, the coupled optimization problems are decomposed into sublevels using multilevel decomposition techniques. In cases with multiple objective functions, formal multiobjective formulation such as the Kreisselmeier-Steinhauser function approach and the modified global criteria approach have been used. Nonlinear programming techniques for continuous design variables and a hybrid optimization technique, based on a simulated annealing algorithm, for discrete design variables have been used for solving the optimization problems. The optimization procedure for gas turbine blades improves the aerodynamic and heat transfer characteristics of the blades. The two-dimensional, blade-to-blade aerodynamic analysis is performed using a panel code. The blade heat transfer analysis is performed using an in-house developed finite element procedure. The optimization procedure yields blade shapes with significantly improved velocity and temperature distributions. The multidisciplinary design optimization procedures for high speed wing-body configurations simultaneously improve the aerodynamic, the sonic boom and the structural characteristics of the aircraft. The flow solution is obtained using a comprehensive parabolized Navier Stokes solver. Sonic boom analysis is performed using an extrapolation procedure. The aircraft wing load carrying member is modeled as either an isotropic or a composite box beam. The isotropic box beam is analyzed using thin wall theory. The composite box beam is analyzed using a finite element procedure. The developed optimization procedures yield significant improvements in all the performance criteria and provide interesting design trade-offs. The semi-analytical sensitivity analysis techniques offer significant computational savings and allow the use of comprehensive analysis procedures within design optimization studies.

Chattopadhyay, Aditi↗
NASA NTRS2001

Free Vibration of Uncertain Unsymmetrically Laminated Beams

Monte Carlo Simulation and Stochastic FEA are used to predict randomness in the free vibration response of thin unsymmetrically laminated beams. For the present study, it is assumed that randomness in the response is only caused by uncertainties in the ply orientations. The ply orientations may become random or uncertain during the manufacturing process. A new 16-dof beam element, based on the first-order shear deformation beam theory, is used to study the stochastic nature of the natural frequencies. Using variational principles, the element stiffness matrix and mass matrix are obtained through analytical integration. Using a random sequence a large data set is generated, containing possible random ply-orientations. This data is assumed to be symmetric. The stochastic-based finite element model for free vibrations predicts the relation between the randomness in fundamental natural frequencies and the randomness in ply-orientation. The sensitivity derivatives are calculated numerically through an exact formulation. The squared fundamental natural frequencies are expressed in terms of deterministic and probabilistic quantities, allowing to determine how sensitive they are to variations in ply angles. The predicted mean-valued fundamental natural frequency squared and the variance of the present model are in good agreement with Monte Carlo Simulation. Results, also, show that variations between plus or minus 5 degrees in ply-angles can affect free vibration response of unsymmetrically and symmetrically laminated beams.

Kapania, Rakesh K.↗
NASA NTRS1971

Millimeter-wave generation with spiraling electron beams

The feasibility of using the interaction between a thin, solid, spiraling electron beam of 10 to 20 kV energy and a microwave cavity to generate watts of CW millimeter-wave power was investigated. Experimental results are given for several prototype devices operating at 9.4 GHz and at 94 GHz. Power outputs of 5 W, and electronic efficiencies near 3%, were obtained at X band, and moderate gain was obtained at 94 GHz. The small-signal theory gives a good fit to the X-band data, and the device behavior at 94 GHz is as expected from the given beam characteristics. The performance is limited chiefly by the velocity spread in the spiraling electron beam, and once this can be brought under control, high-power generation of millimeter waves appears quite feasible with this type of device.

Kulke, B.↗
NASA NTRS2008

Strain and Temperature Sensing Properties of Multiwalled Carbon Nanotube Yarn Composites

Strain and temperature response of Multiwalled Carbon Nanotube (MWCNT/CNT) yarns on a stainless steel test beam has been studied. The carbon nanotube yarns are spun from a multiwalled carbon nanotube forest grown on a silicon substrate to a 4-ply yarn with a diameter of about 15-20 microns. Four of the 4-ply CNT yarns are arranged in a Wheatstone bridge configuration on the stainless steel test beam using a thin layer of polyurethane resin that insulates and protects the yarns from the test beam. Strain sensitivities of the CNT yarn sensors range from 1.39 to 1.75 mV/V/1000 microstrain at room temperature, and temperature sensitivity of the CNT yarn bridge is 91 microA/degC. Resistance of the yarns range from 215 to 270 ohms for CNT yarn length of approximately 5 mm. Processes used in attaching the CNT yarns on the test beam and experimental procedures used for the measurements are described. Conventional metallic foil strain gages are attached to the test beam to compare with the CNT sensors. The study demonstrates multifunctional capability of the sensor for strain and temperature measurements and shows its applicability where engineering strain is less than 3%.

Kahng, Seun K.↗
NASA NTRS1982

Comparison of beam and shell theories for the vibrations of thin turbomachinery blades

Vibration analysis of turbomachinery blades has traditionally been carried out by means of beam theory. In recent years two-dimensional methods of blade vibration analysis have been developed, most of which utilize finite elements and tend to require considerable computation time. More recently a two-dimensional method of blade analysis has evolved which does not require finite elements and is based upon shell equations. The present investigation has the primary objective to demonstrate the accuracy and limitations of blade vibration analyses which utilize one-dimensional, beam theories. It is found that beam theory is generally inadequate to determine the free vibration frequencies and mode shapes of moderate to low aspect ratio turbomachinery blades. The shallow shell theory, by contrast, is capable of representing all the vibration modes accurately. However, the one-dimensional beam theory has an important advantage over the two-dimensional shell theory for blades and vibration modes. It uses fewer degrees of freedom, thus requiring less computer time.

Leissa, A. W.↗
DOE OSTI2023

Element-Specific Study of Magnetic Anisotropy and Hardening in SmCo 5– x Cu x Thin Films

This work investigates the effect of copper substitution on the magnetic properties of SmCo 5 thin films synthesized by molecular beam epitaxy. A series of thin films with varying concentrations of Cu were grown under otherwise identical conditions to disentangle structural and compositional effects on the magnetic behavior. The combined experimental and theoretical studies show that Cu substitution at the Co 3g sites not only stabilizes the formation of the SmCo 5 structure but also enhances magnetic anisotropy and coercivity. Density functional theory calculations indicate that Sm(Co 4 Cu 3g ) 5 possesses a higher single-ion anisotropy as compared to pure SmCo 5 . In addition, X-ray magnetic circular dichroism reveals that Cu substitution causes an increasing decoupling of the Sm 4f and Co 3d moments. Scanning transmission electron microscopy confirms predominantly SmCo 5 phase formation and reveals nanoscale inhomogeneities in the Cu and Co distribution. Our study based on thin film model systems and advanced characterization as well as modeling reveals novel aspects of the complex interplay of intrinsic and extrinsic contributions to magnetic hysteresis in rare-earth-based magnets, i.e., the combination of increased intrinsic anisotropy due to Cu substitution and the extrinsic effect of inhomogeneous elemental distribution of Cu and Co.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1989

Closure of field-aligned currents carried by super-Alfvenic auroral electrons

A linear analysis is carried out to investigate how the return current is generated for the field-aligned current carried by a super-Alfvenic auroral electron beam. If the electron beam is a thin sheet with thickness less than or equal to the electron inertia length, the negative space charge of the beam is neutralized by the ion polarization current produced by the beam. The return current in this case is generated on the two outsides of the beam connected to the polarization current to form a closed current loop. This current structure can explain the thin (a few km) current sheets in the auroral arcs observed by satellites.

Nakamura, Tadas↗
DOE OSTI2022

Molecular Beam Epitaxy (MBE) Growth of Model Cathodes to Study Interfacial Ion Diffusion

Lithium-ion batteries (LIBs) have been the focus of research for decades owing to their superior energy storage potential and wide range of applications. However, long-term stability issues still persist in LIB cathodes as the result of the formation of a solid electrolyte interface (SEI), structural transformations, or the loss of active cathode materials. In nanoscale cathodes, it is often impossible to isolate, let alone mitigate the causes of the observed capacity loss. Herein, a novel approach is presented to synthesizing LIB cathode model systems using thin-film molecular beam epitaxy (MBE). Specifically, 100 nm thick LiMn 2 O 4 (LMO) thin-film cathodes are grown on SrRuO 3 /SrTiO 3 (100) single-crystal substrates and characterized in their pristine and cycled states. The pristine thin films exhibit the electro-chemical cycling behavior and structural evolution previously seen in bulk LMO cathodes. The formation of surface-layer rocksalt MnO and spinel Mn 3 O 4 along with the mass-loss associated with the corrosion of active Mn ions is also reported. It is, therefore, demonstrated that these MBE-grown model systems can be used for detailed studies of their surface structures and the electrode/electrolyte interfacial evolution in LIB cathodes, leading to the development of materials for rechargeable batteries with higher capacity and better stability.

25 ENERGY STORAGE↗
NASA NTRS1994

Optical Scattering and Microstructure of Ion Beam Deposited Metal Coatings

Thin films of gold and platinum have been deposited onto super-polished fused silica substrates using thermal evaporation, ion assisted deposition (IAD), sputtering and ion assisted sputtering. The influence of ion beam flux, coating material and deposition rate on the films microroughness have been investigated. Coatings of gold and platinum have been bombarded with low energy (10-20 eV) Ar ions from an electron cyclotron resonance (ECR) ion source during deposition. Short range surface microroughness of coated surfaces has been examined using scanning tunneling microscopy (STM) and atomic force microscopy (AFM), while long range surface microroughness has been characterized using an angle resolved optical scatterometer. Results indicate that bombardment with low energy ions causes significant reduction in microroughness of metal coatings.

metal↗
NASA NTRS1983

Accelerator simulation of astrophysical processes

Phenomena that involve accelerated ions in stellar processes that can be simulated with laboratory accelerators are described. Stellar evolutionary phases, such as the CNO cycle, have been partially explored with accelerators, up to the consumption of He by alpha particle radiative capture reactions. Further experimentation is indicated on reactions featuring N-13(p,gamma)O-14, O-15(alpha, gamma)Ne-19, and O-14(alpha,p)F-17. Accelerated beams interacting with thin foils produce reaction products that permit a determination of possible elemental abundances in stellar objects. Additionally, isotopic ratios observed in chondrites can be duplicated with accelerator beam interactions and thus constraints can be set on the conditions producing the meteorites. Data from isotopic fractionation from sputtering, i.e., blasting surface atoms from a material using a low energy ion beam, leads to possible models for processes occurring in supernova explosions. Finally, molecules can be synthesized with accelerators and compared with spectroscopic observations of stellar winds.

Tombrello, T. A.↗
NASA NTRS1988

Creep rupture analysis of a beam resting on high temperature foundation

A simplified uniaxial strain controlled creep damage law is deduced with the use of experimental observation from a more complex strain dependent law. This creep damage law correlates the creep damage, which is interpreted as the density variation in the material, directly with the accumulated creep strain. Based on the deduced uniaxial strain controlled creep damage law, a continuum mechanical creep rupture analysis is carried out for a beam resting on a high temperature elastic (Winkler) foundation. The analysis includes the determination of the nondimensional time for initial rupture, the propagation of the rupture front with the associated thinning of the beam, and the influence of creep damage on the deflection of the beam. Creep damage starts accumulating in the beam as soon as the load is applied, and a creep rupture front develops at and propagates from the point at which the creep damage first reaches its critical value. By introducing a series of fundamental assumptions within the framework of technical Euler-Bernoulli type beam theory, a governing set of integro-differential equations is derived in terms of the nondimensional bending moment and the deflection. These governing equations are subjected to a set of interface conditions at the propagating rupture front. A numerical technique is developed to solve the governing equations together with the interface equations, and the computed results are presented and discussed in detail.

Gu, Randy J.↗
DOE OSTI2022

Tuning of the electronic and vibrational properties of epitaxial MoS 2 through He-ion beam modification

Abstract Atomically thin transition metal dichalcogenides (TMDs), like MoS 2 with high carrier mobilities and tunable electron dispersions, are unique active material candidates for next generation opto-electronic devices. Previous studies on ion irradiation show great potential applications when applied to two-dimensional (2D) materials, yet have been limited to micron size exfoliated flakes or smaller. To demonstrate the scalability of this method for industrial applications, we report the application of relatively low power (50 keV) 4 He + ion irradiation towards tuning the optoelectronic properties of an epitaxially grown continuous film of MoS 2 at the wafer scale, and demonstrate that precise manipulation of atomistic defects can be achieved in TMD films using ion implanters. The effect of 4 He + ion fluence on the PL and Raman signatures of the irradiated film provides new insights into the type and concentration of defects formed in the MoS 2 lattice, which are quantified through ion beam analysis. PL and Raman spectroscopy indicate that point defects are generated without causing disruption to the underlying lattice structure of the 2D films and hence, this technique can prove to be an effective way to achieve defect-mediated control over the opto-electronic properties of MoS 2 and other 2D materials.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Atomic layer molecular beam epitaxy of kagome magnet RMn6Sn6 (R = Er, Tb) thin films

Kagome lattices have garnered substantial interest because their band structure consists of topological flat bands and Dirac cones. The RMn6Sn6 (R = rare earth) compounds are particularly interesting because of the existence of the large intrinsic anomalous Hall effect (AHE), which originates from the gapped Dirac cones near the Fermi level. This makes RMn6Sn6 an outstanding candidate for realizing the high-temperature quantum AHE. The growth of RMn6Sn6 thin films is beneficial for both fundamental research and potential applications. However, most of the studies on RMn6Sn6 have focused on bulk crystals, and the synthesis of RMn6Sn6 thin films has not been reported so far. Here, we report the atomic layer molecular beam epitaxy growth, structural and magnetic characterizations, and transport properties of ErMn6Sn6 and TbMn6Sn6 thin films. It is especially noteworthy that TbMn6Sn6 thin films have out-of-plane magnetic anisotropy, which is important for realizing the quantum AHE. Our work paves the avenue toward the control of the AHE using devices patterned from RMn6Sn6 thin films.

Materials Science↗
NASA NTRS1972

Limitations on millimeter-wave power generation with spiraling electron beams.

A study is made of the suitability of the interaction between a thin, solid, spiraling electron beam of 5-15-kV energy and a microwave cavity, for the purpose of generating watts of CW millimeter-wave power. The effect of finite energy spread in the electron beam is considered both theoretically and experimentally. Measured results are given for a prototype device operating at 9.4 GHz. Power outputs of 5 W and electronic efficiencies near 2% have been obtained. The data agree well with the theory, subject to some ambiguity in the energy-distribution parameters. The performance is strongly limited by the energy spread in the beam.

Kulke, B.↗
DOE OSTI2025

Characterization of laser-accelerated proton beams from a 0.5 kJ sub-picosecond laser for radiography applications

Laser-accelerated ion beams show promise for many applications, including high-resolution flash imaging of static or dynamic objects in next-generation radiography to probe materials and plasmas in extreme environments and inertial confinement fusion. To scale up ion beam production for radiography applications, we conducted experiments using sub-picosecond lasers up to 0.5 kJ at the OMEGA-EP facility to characterize proton beams from solid targets, primarily CH/CD sub-micron thin films from which ion beams were also used for static and dynamic radiography for the first time. For standalone sub-micron thin CH films, the highest detected proton energy is in the range of 72–97 MeV. Proton beams with highest energy near or above 60 MeV at full laser energy and similar beam profiles are also measured from low-density CD foams and flat CH foil target of micrometer-scale thickness. The ~ 700–800 nm CH/CD foils achieve the highest ion yield among the targets tested. For sub-micron thin films, the laser prepulse can expand the target and lead to complex interactions, which is simulated using coupled hydrodynamic and two-step kinetic models. Simulations suggest the presence of a micrometer-scale preplasma plateau with near-critical density and further indicate that target normal sheath acceleration, electron heating from Relativistic transparency in the preplasma plateau, and background proton reflection from carbon ion front at the rear side contribute to the resulting proton spectrum from these sub-micron thin targets at various stages. These proton beams show strong potential for radiography and for production of secondary sources.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Structural Changes in YBa 2 Cu 3 O 7 Thin Films Modified with He + -Focused Ion Beam for High-Temperature Superconductive Nanoelectronics

Irradiation of high-temperature superconductor YBa 2 Cu 3 O 7 (YBCO) with high-energy He + ions is known to cause structural changes in the YBCO film, decreasing the critical temperature T C and finally leading to a superconductor-to-insulator transition. Here, this allows one to pattern narrow insulating regions with a focused ion beam (FIB) and thus fabricate nanoscale Josephson junctions on YBCO films. Moreover, such ion irradiation is known to cause structural changes in the YBCO film. However, details of how these structural changes occur in nanoscale devices produced by FIB remain unknown. Using nanofocus X-ray diffraction, we study the changes in the YBCO crystal lattice and investigate how the nature of these changes depends on the size of the irradiated regions. These data provide an important understanding of how oxide superconductors can be tailored at the nanometer scale for various applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗