Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMPATIBILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Compatibility of Wrought Superalloys with Supercritical CO2

Supercritical CO2 (sCO2) power cycles, particularly direct-fired cycles, have the possibility of revolutionizing clean fossil energy with peak temperatures above 700 °C and wrought precipitation strengthened alloys like Haynes 282™ for structural components. At temperatures <650 °C, it would be desirable to use less expensive alloys, however, steels are known to be susceptible to carburization. Laboratory 300 bar sCO2 autoclave results were collected on a range of alloys including less expensive Ni-based alloys like 825 compared to advanced austenitic steels like alloy 709 at 600 °C. Both alloys 825 and 709 formed thin, protective Cr-rich oxides after 1,000 h. Alloy 825 also was exposed for 1,000 h in sCO2 at 800 °C and compared to a range of Ni-based alloys. Comparing alloys 625, 825, and 282, the mass gain increased with increasing alloy Ti content under these conditions. High Al superalloys did not perform significantly better under these conditions at 800 °C.

Pint, Bruce↗
DOE OSTI2023

Compatibility of mesophase pitch and linear low-density polyethylene for low-cost carbon fiber

Mesophase pitch and linear low-density polyethylene (LLDPE) were blended by shear mixing and extruded producing precursor fibers which were then converted to carbon fibers (CFs). LLDPE additives agglomerate within the isotropic spheres rather than uniformly dispersing throughout the entire matrix. The blends possess different thermal properties and precursor tensile properties evident by two-phase tensile stress nature not present in precursor fibers produced from pure pitch. The resultant CFs were oxidized at 280 °C for 4 h and carbonized at 1000 °C for 15 min. This process created pitch CFs with a tensile strength of 1.23 GPa and a Young’s modulus of 99 GPa. All CFs produced from blends of pitch and LLDPE possessed a tensile strength of 0.63 GPa and less. These CFs showed a microstructure slightly different from the pure pitch CFs with fractured CF cross sections revealing voids present in all blended CFs due to burnt off LLDPE stemming from carbonization. Further study into compatibilizers and new conversion processes is required to successfully blend LLDPE with mesophase pitch for the purpose of producing a new low-cost CF.

36 MATERIALS SCIENCE↗
DOE OSTI2020

SiC compatibility

SiC is a relatively chemically stable ceramic that has potential use in the extreme environments present in nuclear reactors. Reactions with high temperature steam, He, hydrothermal, molten salts, and liquid metals are some of the possible environments that SiC could be exposed to. While it is very stable in air, aqueous environments and very low oxygen partial pressures can lead to SiC recession. Generally, SiC does not react with the FliNaK or FliBe molten salts, or liquid metals, however contaminants in these working fluids leached from other materials can cause reaction layers to occur. Most of these systems require additional testing under neutron irradiation to determine if there are any combined effects.

Mouche, Peter↗
DOE OSTI2021

Specific molecular design of polycarboxylate polymers exhibiting optimal compatibility with clay contaminants in concrete

Highlights: • Allyl ether-based PCEs with short side chain length and low side chain density presented superior clay resistance. • PCEs with medium side chain density exhibited best clay robustness when compared at the absolute dosed quantities. • The proportion of PCE being intercalated into the layered structure of clay was quantified. It is widely recognized that the dispersing ability of polycarboxylate superplasticizers (PCEs) could be hindered due to the presence of clay contaminants in concrete. In this study, a series of allyl ether-based polycarboxylate superplasticizers possessing short polyethylene glycol side chains was successfully synthesized and probed for their clay tolerance. The resulting PCE polymers were characterized via Size Exclusion Chromatography (SEC) to obtain their molecular properties. Thereafter, their dispersing ability was probed in the absence and presence of sodium bentonite. Allyl ether-based polycarboxylate (APEG) polymers possessing short side chains were found to exhibit enhanced clay resistance as compared to that of conventional MPEG PCEs holding long pendant chains. The mode of interaction between APEG PCEs and bentonite was investigated via sorption and XRD measurements. The data revealed that APEG PCEs possessing a lower side chain density intercalate less into the interlayer space of bentonite than those exhibiting higher side chain density.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Evaluating hydrogen permeation through medium-density and high-density polyethylene pipes to enable a hydrogen-compatible infrastructure

As the United States and the global community pursue energy abundance and resilience, hydrogen is becoming a critical energy carrier. The future of hydrogen transport depends on one thing: verifying that today’s pipelines are hydrogen ready. This study investigates the permeation behavior of medium-density polyethylene (MDPE) and high-density polyethylene (HDPE) pipelines under pure hydrogen gas environment at various pressures and temperatures. Using thermal desorption analysis (TDA) and direct pipe permeability measurements, hydrogen loss rates are quantified, revealing minimal permeation losses (< 10.5 g/km/day) under realistic operating conditions. Effects of temperature and pressure with Standard Dimension Ratios (SDR), were evaluated to determine their influence on permeation rates of MDPE and HDPE pipelines. In addition, ex-situ density and degree of crystallinity (DOC) of MDPE and HDPEs after hydrogen exposure were also investigated to understand pressure-dependency of polymer properties. The findings provide essential data for assessing polymer-based pipeline materials for safe and reliable hydrogen transport.

08 HYDROGEN↗
DOE OSTI2022

Compatibility of Fe-Cr-Al and Fe-Cr-Al-Mo oxide dispersion strengthened steels with static liquid sodium at 700 °C

We report the corrosion behavior and tensile properties of oxide dispersion strengthened (ODS) FeCr, FeCrAl, FeCrAlMo steels and 316H stainless steel were evaluated after 1000 h at 700 °C in static sodium with and without an oxygen getter (Zr foil). Without Zr foil to getter the dissolved oxygen in the liquid sodium, combined oxidation (formation of Cr, Fe-rich or Al-rich oxides) and dissolution of the studied materials was observed. For the ODS FeCr, Cr- and Fe-rich oxide formation and dissolution induced Cr depletion in the underlying alloy and led to the formation of laves phases that were observed to be detrimental to the room temperature tensile properties. For ODS FeCrAlMo and FeCrAl Al-rich oxide formation and dissolution resulted in Al depletion in the underlying alloys but did not impact tensile properties at room temperature. For 316H temperature induced sensitization combined with oxidation decreased room temperature tensile properties. With Zr foil added as oxygen getter, roughened surfaces and Al depletion profiles suggested the dissolution of ODS FeCr and FeCrAl into the liquid sodium while limited dissolution was observed for ODS FeCrAlMo and 316H. For the 316H and ODS FeCrAlMo steels, precipitates were formed at the grain boundaries after exposure. Tensile properties of ODS FeCr, FeCrAl and FeCrAlMo were not affected by the 1000 h corrosion exposure with Zr foil added to the sodium but for 316H temperature-induced grain boundary sensitization negatively affected the tensile properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Varied enhancements in mechanical properties and sodium compatibility of Grade 92 by thermomechanical treatments

As a candidate material for advanced nuclear reactors, a ferritic-martensitic (FM) steel Grade 92 in the standard normalized and tempered (NT) condition was subjected to two types of thermomechanical treatments (TMTs) with one having a lower level of deformation (T5A) and the other having a higher level of deformation (T5B). The testing results of the three conditions indicated that the TMTs significantly improved yield strength, creep resistance, fracture toughness, and sodium corrosion resistance compared with the NT condition. T5A excelled at creep resistance while T5B at sodium corrosion resistance. Microstructural characterization of the three conditions supports the varied enhancements in the properties. This study suggests that an appropriate TMT can be developed and applied to FM steels to better meet specific application requirements.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Active wall conditioning through boron powder injection compatible $\mathrm{ELM}$ control in $\mathrm{EAST}$

Real-time wall conditioning and edge-localized mode (ELM) suppression through real-time boron powder injection into high-confinement mode discharges of the Experimental Advanced Superconducting Tokamak (EAST) have been investigated. The boron powder injection effectively conditioned the plasma-facing components, as shown by the reductions in low-Z and high-Z impurities and the global recycling level in the whole inner vessel, and suppressed the strong magnetohydrodynamic (MHD) activity in the plasma core. The improved wall conditions also resulted in an earlier transition from L- to H-mode. Boron powder injection also effectively suppressed ELM in the lower single null configuration with BT in the favorable direction while leaving the plasma density and stored energy largely unaffected.

36 MATERIALS SCIENCE↗