Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONICAL CONFIGURATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Configuration of singular optical cones in gyrotropic crystals with dichroism

Optical conic singularities in crystals with linear dichroism and natural optical activity at the point of intersection of dispersion curves for the main refractive indices are considered. The possible existence of singularities like a nodal point, tangency point, triple point, and cusps of the first and second order is demonstrated. Forty-nine different types of irreducible fourth-order optical cones obtained by sequential bifurcations of eight main singular cones are established. The classification is based on the concept of roughness of systems depending on parameters.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DSMC simulation of low Reynolds number nozzle flows

A numerical analysis of low Reynolds number nozzle flows was performed to investigate the loss mechanisms involved and to determine the nozzle wall contour that minimizes these losses. DSMC was used to simulate flows through three different nozzle configurations at two different stagnation chamber temperatures so that the heat transfer losses could be separated from the wall contour effects on performance. A trumpet-shaped nozzle had 5 percent higher efficiency than a conical nozzle and a 3 percent higher efficiency than a bell-shaped nozzle with the unheated flow. With heated flow both the trumpet and bell-shaped nozzles had a 6.5 percent higher efficiency than the conical nozzle. The conical nozzle had the highest discharge coefficient of the three configurations, 0.92, and the trumpet-shaped nozzle had the lowest, 0.82. The discharge coefficient of each nozzle was unaffected by the change in stagnation temperature; however the increase in stagnation temperature increased the heat transfer and viscous losses in the boundary layer. These results suggest that the trumpet-shaped wall contour performed most efficiently except near the throat region, where it incurred large viscous losses. However, the bell-shaped nozzle may increase its overall performance with an increase in stagnation temperature.

Zelesnik, D.↗

The Venus ionosphere as an obstacle to the solar wind

Pioneer Venus Orbiter Electron Temperature Probe measurements of hundreds of bow shock and ionopause crossings are employed in describing the configuration of these two boundaries and their variations in response to changes in solar wind pressure. The average bow shock configuration is found to be well represented by an Archimedian hyperboloid whose altitude at the subsolar point is 0.46 Venus radii, a value slightly greater than that derived from Pioneer Venus magnetometer data using a fit to a general conic section. It is noted that the average bow shock configuration exhibits a high degree of azimuthal symmetry near the terminator. The orbit to orbit variability of the shock location is unexpectedly large, the standard deviation being about 10%. A tendency is noted for the bow shock and the ionopause to expand and contract simultaneously, but the weakness of their orbit by orbit correlation suggests that the ionopause of Venus is not the only obstacle to the solar wind. It is thought that such processes as photoion pickup and charge exchange with neutrals may be important in diverting the solar wind plasma around the planet.

Theis, R. F.↗

Inlet boundary-layer shapes on four aircraft forebodies at Mach 6

Boundary-layer shape measurements at the engine inlet on four different hypersonic aircraft forebody designs (with no engine on the forebody) are reported. The measurements provide a qualitative assessment of the effectiveness of various forebody geometries as engine inlet precompression surfaces. The designs, tested in a hypersonic tunnel at Mach 6 and a nominal freestream Reynolds number of 30,500,000, included a semiconical forebody, a configuration similar to a slab delta wing, a conical nose blended into a flat surface, and a conical, complex forebody shape. Boundary layer height as a function of forebody compression is shown for each design.

Lawing, P. L.↗

Three-dimensional flow over a conical afterbody containing a centered propulsive jet - A numerical simulation

The supersonic flow field over a body of revolution incident to the free stream is simulated numerically on a large, array processor (the CDC Cyber 205). The configuration is composed of a cone-cylinder forebody followed by a conical afterbody from which emanates a centered, supersonic propulsive jet. The free-stream Mach number is 2, the jet-exit Mach number is 2.5, and the jet-to-free-stream static pressure ratio is 3. Both the external flow and the exhaust are ideal air at a common total temperature. The thin-layer approximation to the time-dependent, compressible, Reynolds-averaged Navier-Stokes equations are solved using an implicit finite-difference algorithm. The data base, of 5 million words, is structured in a 'pencil' format so that efficient use of the array processor can be realized. The computer code is completely vectorized to take advantage of the data structure. Turbulence closure is achieved using an empirical algebraic eddy-viscosity model. The configuration and flow conditions correspond to published experimental tests and the computed solutions are consistent with the experimental data.

Deiwert, G. S.↗

Analytical and experimental investigation of stator endwall contouring in a small axial-flow turbine. 1: Stator performance

Three stator configurations were studied to determine the effect of stator outer endwall contouring on stator performance. One configuration was a cylindrical stator design. One contoured stator configuration had an S-shaped outer endwall, the other had a conical-convergent outer endwall. The experimental investigation consisted of annular surveys of stator exit total pressure and flow angle for each stator configuration over a range of stator pressure ratio. Radial variations in stator loss and aftermixed flow conditions were obtained when these data were compared with the analytical results to assess the validity of the analysis, good agreement was found.

Haas, J. E.↗

Three-dimensional flow over a conical afterbody containing a centered propulsive jet: A numerical simulation

The supersonic flow field over a body of revolution incident to the free stream is simulated numerically on a large, array processor (the CDC CYBER 205). The configuration is composed of a cone-cylinder forebody followed by a conical afterbody from which emanates a centered, supersonic propulsive jet. The free-stream Mach number is 2, the jet-exist Mach number is 2.5, and the jet-to-free-stream static pressure ratio is 3. Both the external flow and the exhaust are ideal air at a common total temperature.

Deiwert, G. S.↗

Design and analysis of soft X-ray imaging microscopes

The spherical Schwarzschild microscope for soft X-ray applications in microscopy and projection lithography consists of two concentric spherical mirrors configured such that the third-order spherical aberration and coma are zero. Since multilayers are used on the mirror substrates for X-ray applications, it is desirable to have only two reflecting surfaces in a microscope. To reduce microscope aberrations and increase the field of view, generalized mirror surface profiles are here considered. Based on incoherent and sine wave modulation transfer function calculations, the object plane resolution of a microscope has been analyzed as a function of the object height and numerical aperture (NA) of the primary for several spherical Schwarzschild, conic, and aspherical Head reflecting two-mirror microscope configurations. The Head microscope with a NA of 0.4 achieves diffraction limited performance for objects with a diameter of 40 microns. Thus, it seems possible to record images with a feature size less than 100 A with a 40x microscope when using 40 A radiation.

Shealy, David L.↗

Space shuttle: Aerodynamic characteristics of a composite booster/040A orbiter launch configuration with fin and booster body configuration effect contribution

An investigation was made of the fin configuration and booster body configuration effects on a composite booster/040A orbiter launch configuration. Aerodynamic performance and stability characteristics in pitch and yaw were obtained. Configurations tested included two stepped cylindrical bodies of different lengths with a conical nose, four fin shapes of various sizes and aspect ratios mounted in different positions around the base of the bodies, two base flare angles and three 040A orbiter configurations. The orbiter variations included a tailless configuration and two tail sizes. A tailless booster launch configuration with deflected petals (expanded flare sectors) was also tested. The model scale was 0.003366. Data were converted to coefficient form in near real time, punched on cards, and tabulated. The cards used in conjunction with a Benson-Lehner plotter were used to provide plotted data. At the end of the test, tabulated input forms were completed for the SADSAC computer program to aid in publishing the final test data report.

Ainsworth, R. W.↗

CoSSIR: A New Instrument for Exploring the Utility of Submillimeter-wave Radiometry for Earth Observation

The Conical Scanning Submillimeter-wave Imaging Radiometer (CoSSIR) has been developed to study the application of submillimeter-wave radiometry for remote sensing of cirrus clouds and humidity sounding. Measurements of the global distribution of ice cloud mass and particle size are important for understanding the Earth s energy budget and for evaluating global climate models. The spatial variability and the wide variety of cloud particle shapes and sizes make ice clouds particularly difficult to measure. Ice clouds are essentially undetectable at microwave frequencies due to the low dielectric of ice and small size of the particles relative to wavelength. However, submillimeter wavelengths demonstrate significant response to the presence of ice clouds thus this frequency regime is applicable to measuring ice clouds. Another potentially viable application for submillimeter-wave radiometry is humidity and temperature sounding. The principle of sounding at submillimeter wavelengths is similar to that at microwavelengths. Submillimeter-wave radiometry has the advantage of achieving finer spatial resolution using a smaller antenna aperture which is an important consideration for spaceborne observatories. Submillimeter-wave radiometry also offers the potential of sounding over land and as a surrogate measurement for precipitation. CoSSIR is a new instrument to explore these applications. The CoSSIR is designed to fly aboard the ER-2 aircraft and its modest size (approximately 100 kg) permits it to be configured for other aircraft. A dual-axes gimbals mechanism provides conical, across-track, and along-track scanning capability. In its present configuration CoSSIR has fifteen channels between 183 GHz and 640 GHz. Three channels are centered about the 183 GHz water vapor absorption line, four channels are centered about the 380 GHz water vapor absorption line, and three dual-polarized channels are centered about the 487 GHz oxygen absorption line. Two channels are located in atmospheric windows at 220 GHz and 640 GHz. All channels are single-linear polarized with the exception of those near 487 GHz. Calibration is achieved by periodically observing two blackbody radiators; one blackbody is heated to approximately 325 K and the other is approximately 250 K during flight. Details of the instrument design as well as measurements from the Cirrus Regional Study of Tropical Anvils and Cirrus Layers - Florida Area Cirrus Experiment will be presented.

Racette, P. E.↗

Performance of Several Method-of-Characteristics Exhaust Nozzles

Nozzle performance data were obtained with three "method-of-characteristics" nozzles and a 150 conical nozzle at pressure ratios up to 130. Each basic configuration was cut off and tested at expansion ratios of 25, 20, 15, and 10. Unheated dry air was used at nozzle inlet pressures up to 22,000 pounds per square foot absolute. Nozzle thrust data were extrapolated to infinite pressure ratio (zero discharge pressure). As much as 1-percent increase in thrust with no increase in nozzle surface area (weight), can be obtained by using a method-of-characteristics, nozzle instead of a 15 conical nozzle when operating with a nozzle expansion ratio of 25 and nozzle pressure ratios from 200 to infinity. Conversely, for the same thrust, reductions in nozzle divergent surface area in the order of 25 percent are possible. The thrust performance of the method-of-characteristics nozzle was not as good as that of the 150 conical nozzle when operating at pressure ratios considerably below design (below 100 for the expansion ratio 25 nozzles). Theoretical and measured nozzle momentum coefficients agreed within about 0.6 percent. This is the order of accuracy of both the measured and theoretical values.

Farley, John M.↗

Wind-tunnel tests of a single stage to orbit space shuttle at Mach numbers of 2.60, 3.85, and 4.64

Wind tunnel tests were conducted to determine the static aerodynamic characteristics of a single-stage-to-orbit space shuttle model at Mach numbers of 2.60, 3.85, and 4.64. Test parameters included various payloads for the launch configurations and various corner radii for the entry configurations. The test results for the launch configurations generally indicated that a decrease in payload size resulted in a marked increase in axial force. Decreasing the corner radii of the entry configuration led to large increases in axial force. The results also indicated that the presence of an engine door on the entry configuration caused a measurable positive increment in pitching moment. Changing the entry configuration afterbody geometry from a biconic shape to a conic shape increased the normal-force and stability level.

Graves, E. B.↗

Forebody vortex management for yaw control at high angles of attack

The yaw-control potential of deployable forebody strakes at angles of attack above the range of conventional rudder effectiveness has been investigated. The conformally-stored strakes when deployed force asymmetrical vortex shedding from the forebody, thereby generating a controlled yawing moment. The concept was explored through low-speed wind tunnel tests on a conical forebody in isolation and in a generic fighter configuration. Force and moment measurements on the complete model were supplemented with circumferential pressure and flow-visualization surveys on an isolated forebody, in order to gain insight into the vortex flow mechanisms resulting from forced asymmetrical separations and to quantify the obtainable yaw power at angles of attack to 80 deg. This preliminary, low-Reynolds-number study showed asymmetrically-deployed forebody strakes to have considerable yaw control potential, whose sensitivity to scale effects needs further investigation.

Rao, D. M.↗

Experimental investigation of a simulated LOX injector flow field and other nonintrusive measurement efforts

Efforts to improve the characteristics of fuel-oxidizer mixing in liquid rocket combustors have lead to a swirl element design for a liquid oxygen injector which is being considered for use on the STME. For the design which is the subject of this investigation, the oxygen enters the injector element perpendicular to the injector axis and nearly tangent to the circular injector wall. This swirl element is at one end of a tube and the injector exit is at the other. This geometric configuration creates a plume in the shape of a conical sheet. This sheet is either primarily contiguous liquid or droplets depending on the pressure drop in the injector and the distance from the injector exit. Probe-based devices such as two-dimensional grid patternators have been used to investigate simulated LOX injector flow fields (Hulka). The primary work described herein is an effort to use optical techniques to investigate the plume of a swirl injector element. For this investigation, a high pressure (500 psig) cold flow test facility was constructed. Water was used as the LOX simulate and air pressure was used to drive the injector flow field. Laser-induced fluorescence (LIF) from dye seeded into the water was used to obtain quantitative measurements of the time-averaged water concentration distribution in the plume. Scattered laser light and LIF were used for time averaged plume visualization and scattered light from a strobe with a 1 microsecond pulse was used for time-resolved plume visualization. During the Summer Faculty Fellowship for which this report was developed, an additional effort, unrelated to the swirl injector investigation, was made to resolve fluctuations in the combustion product composition in the exhaust of a hybrid rocket motor. A brief description of this effort is included herein.

Hartfield, Roy J., Jr.↗

Free-jet acoustic investigation of high-radius-ratio coannular plug nozzles. Comprehensive data report, volume 1

Six coannular plug nozzle configurations having inverted velocity and temperature profiles, and a baseline convergent conical nozzle were tested for simulated flight acoustic evaluation in General Electric's Anechoic Free-Jet Acoustic Facility. The nozzles were tested over a range of test conditions that are typical of a Variable Cycle Engine for application to advanced high speed aircraft. The outer stream radius ratio for most of the configurations was 0.853, and the inner-stream-outer-stream area ratio was tested in the range of 0.54. Other variables investigated were the influence of bypass struts, a simple noncontoured convergent-divergent outer stream nozzle for forward quadrant shock noise control, and the effects of varying outer stream radius and inner-stream-to-outer-stream velocity ratios on the flight noise signatures of the nozzles. It was found that in simulated flight, the high-radius-ratio coannular plug nozzles maintain their jet noise and shock noise reduction features previously observed in static testing. The presence of nozzle bypass structs will not significantly effect the acoustic noise reduction features of a General Electric-type nozzle design. A unique coannular plug nozzle flight acoustic spectral prediction method was identified and found to predict the measured results quite well. Special laser velocimeter and acoustic measurements were performed which have given new insight into the jet and shock noise reduction mechanisms of coannular plug nozzles with regard to identifying further beneficial research efforts.

Knott, P. R.↗

Hybrid X-pinches

Results from experimental studies of a hybrid X-pinch with an initial configuration in the form of a high-current diode with conical tungsten electrodes spaced by 1-2 mm and connected to one another with 20- to 100-{mu}m-diameter wires are presented. The experiments were carried out at four facilities with a current amplitude from 200 to 1000 kA and front duration from 45 to 200 ns. It is shown that, in spite of their simpler configuration, hybrid X-pinches with a short rise time of the current pulse (50-100 ns) are highly competitive with standard X-pinches in the generated soft X-ray power and the formation of a single hot spot in them is much more stable, while hard X-ray emission is almost absent. The possibility of using hybrid X-pinches as soft X-ray sources for point projection X-ray imaging of plasma objects is considered.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Dynamics of hybrid X-pinches

The dynamics of a new type of pinches—hybrid X-pinches (HXPs)—has been studied experimentally and numerically. The initial configuration of an HXP consists of a high-current diode with conical tungsten electrodes separated by a 1- to 3-mm-long gap and shunted with a 20- to 100-μm diameter wire. It was shown earlier that a hot spot (HS) with high plasma parameters also formed in the HXP, although its initial configuration is simpler than that of a standard X-pinch. Although details of the HXP dynamics still remain insufficiently studied, the main factors governing the HXP formation were investigated both experimentally and using magnetohydrodynamic simulations. The formation of a specific pressure profile in the electrode plasma after the wire explosion was investigated both experimentally and theoretically. It is shown that the effect of the pressure profile on the expanding wire plasma is similar for both standard X-pinches and HXPs, which allows one to assign them to the same class of loads of pulsed facilities. It is also established that the final stages of HS formation and the parameters of the HS plasma in standard X-pinches and HXPs are practically identical.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Stabilizing Effectiveness of Conical Flares on Bodies with Conical Noses

An analysis is presented of published results of force tests on 80 cone-cylinder-flare configurations at Mach numbers of 2.18, 2.81, and 4.04. The contributions, excluding interference effects, of the cone-cylinder bodies to the over-all normal force derivatives have been removed by means of the second-order shock-expansion method, and the normal force derivatives at zero angle of attack due to the flares alone are shown. The results from a wide variety of configurations are correlated by plotting ratios of the normal force derivatives of the flares to the normal force derivatives of cones having the same included angle. Comparisons are made of the experimental normal force results with the normal force derivatives obtained by assuming conical flow over the flares and with those obtained by use of the second-order shock-expansion method. The comparisons show that use of the second-order shock-expansion method is generally the superior of the two, and in most cases gives values of the normal force derivatives of the flares which agree very well with the experimental results. Centers of pressure of the flares are presented and comparisons are made with results obtained from the theories mentioned. In general, the comparisons show that the assumption of conical flow over the flares is comparable to use of the second-order shock-expansion method in determining the centers of pressure, and in many cases both methods give values which agree closely with the experimental results.

Kirk, Donn B.↗