Search NASA⌕ Search

SEARCH · Search NASA

Results for “CRITICAL STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1946

Critical combinations of shear and transverse direct stress for an infinitely long flat plate with edges elastically restrained against rotation

An exact solution and a closely concurring approximate energy solution are given for the buckling of an infinitely long flat plate under combined shear and transverse direct stress with edges elastically restrained against rotation. It was found that an appreciable fraction of the critical stress in pure shear may be applied to the plate without any reduction in the transverse compressive stress necessary to produce buckling. An interaction formula in general use was shown to be decidedly conservative for the range in which it is supposed to apply.

Batdorf, S B↗
NASA NTRS1991

Computed stress fields in GaAs during vertical Bridgman growth

The thermoelastic stress field of GaAs crystals grown by the vertical Bridgman method has been approximated using a linear elastic, axisymmetric stress model. The model included the effects due to the thermal field and the gravitational field, as well as the interaction with the ampoule, but did not fully account for the elastic anisotropy of the crystal. Realistic thermal fields for different furnace temperatures and insulation zone thicknesses were computed with a similar model. The difference between the Von Mises stress and the critical resolved shear stress (CRSS) was used as a measure of the number of dislocations present. Different sets of growth parameters were examined to determine which produced the lowest amount of stress in the crystal. Results show that the crystal-ampoule interaction is the most important parameter in dislocation generation. In addition, for the same sticking boundary conditions, concave interfaces have lower stress than convex interfaces.

Rosch, William↗
NASA NTRS1939

Local instability of columns with I-, Z-, channel, and rectangular-tube sections

Charts are presented for the coefficients in the formulas for the critical compressive stress at which cross-sectional distortion begins in thin-wall columns of I-, Z-, channel, and rectangular-tube sections. The energy method of Timoshenko was used in the theoretical calculations required for the construction of the charts. The deflection equations were carefully selected to give good accuracy. The calculation of the critical compressive stress at stresses above the elastic range is briefly discussed in order to demonstrate the use of the formulas and the charts in engineering calculations. Two illustrative problems are included.

STRESSED SKIN LMAL↗
NASA NTRS1966

Stress corrosion

This article recounts briefly some of the more critical stress-corrosion failures that have been experienced at Marshall Space Flight Center and the corrective action taken. Some of the recent stress corrosion studies are described and preliminary results tabulated. Specific problems described are the H-1 Engine LOX dome, the pneumatic line fitting sleeve problems and the more recent problem with wave springs used on MF-flared tube fittings. The use of nitric oxide in preventing stress-corrosion failures in titanium tanks is also discussed.

HIGH STRENGTH ALLOY↗
NASA NTRS2007

In-Plane Cracking Behavior and Ultimate Strength for 2D Woven and Braided Melt-Infiltrated SiC/SiC Composites Tensile Loaded in Off-Axis Fiber Directions

The tensile mechanical properties of ceramic matrix composites (CMC) in directions off the primary axes of the reinforcing fibers are important for architectural design of CMC components that are subjected to multi-axial stress states. In this study, 2D-woven melt-infiltrated (MI) SiC/SiC composite panels with balanced fiber content in the 0 degree and 90 degree directions were tensile loaded in-plane in the 0 degree direction and at 45 degree to this direction. In addition, a 2D triaxially-braided MI composite panel with balanced fiber content in the plus or minus 67 degree bias directions and reduced fiber content in the axial direction was tensile loaded perpendicular to the axial direction tows (i.e., 23 degrees from the bias fibers). Stress-strain behavior, acoustic emission, and optical microscopy were used to quantify stress-dependent matrix cracking and ultimate strength in the panels. It was observed that both off-axis loaded panels displayed higher composite onset stresses for through-thickness matrix cracking than the 2D-woven 0/90 panels loaded in the primary 0 degree direction. These improvements for off-axis cracking strength can in part be attributed to higher effective fiber fractions in the loading direction, which in turn reduces internal stresses on critical matrix flaws for a given composite stress. Also for the 0/90 panel loaded in the 45 degree direction, an improved distribution of matrix flaws existed due to the absence of fiber tows perpendicular to the loading direction. In addition, for the +67/0/-67 braided panel, the axial tows perpendicular to the loading direction were not only low in volume fraction, but were also were well separated from one another. Both off-axis oriented panels also showed relatively good ultimate tensile strength when compared to other off-axis oriented composites in the literature, both on an absolute strength basis as well as when normalized by the average fiber strength within the composites. Initial implications are discussed for constituent and architecture design to improve the directional cracking of SiC/SiC CMC components with MI matrices.

Morscher, Gregory N.↗
NASA NTRS1939

Local instability of centrally loaded columns of channel section and Z-section

Charts are presented for the coefficients in formulas for the critical compressive stress at which cross-sectional distortion begins in a thin-wall member with either a channel section or a Z-section with identical flanges. The energy method of Timoshenko was used in the theoretical calculations required for the construction of the charts. The deflection equations were carefully selected to give good accuracy. The calculation of the critical compressive stress at stresses beyond the elastic range is briefly discussed. In order to demonstrate the use of the formulas and the charts in engineering calculations, two illustrative problems are included.

ELASTICITY↗
NASA NTRS1939

Local instability of symmetrical rectangular tubes under axial compression

A chart is presented for the coefficient in the formula for the critical compressive stress at which cross sectional distortion begins in a thin-wall tube of rectangular section symmetrical about its two principal axes. The energy method of Timoshenko was used in the theoretical calculations required for the construction of the chart. The deflection equation used in this method was selected to give good accuracy. The exact values given by solution of the differential equation were calculated for a number of cases and it was found that the energy solution was correct to within a fraction of 1 percent. The calculation of the critical compressive stress at stresses above the elastic range is also discussed. In order to demonstrate the use of the formulas and the chart in engineering calculations, several illustrative problems are included.

TUBING, RECTANGULAR - STRESSES, COMPRESSIVE↗
NASA NTRS1992

Critical assessment of Reynolds stress turbulence models using homogeneous flows

In modeling the rapid part of the pressure correlation term in the Reynolds stress transport equations, extensive use has been made of its exact properties which were first suggested by Rotta. These, for example, have been employed in obtaining the widely used Launder, Reece and Rodi (LRR) model. Some recent proposals have dropped one of these properties to obtain new models. We demonstrate, by computing some simple homogeneous flows, that doing so does not lead to any significant improvements over the LRR model and it is not the right direction in improving the performance of existing models. The reason for this, in our opinion, is that violation of one of the exact properties can not bring in any new physics into the model. We compute thirteen homogeneous flows using LRR (with a recalibrated rapid term constant), IP and SSG models. The flows computed include the flow through axisymmetric contraction; axisymmetric expansion; distortion by plane strain; and homogeneous shear flows with and without rotation. Results show that for most general representation for a model linear in the anisotropic tensor, performs either better or as good as the other two models of the same level.

Shabbir, Aamir↗
NASA NTRS1993

Critical assessment of Reynolds stress turbulence models using homogeneous flows

In modeling the rapid part of the pressure correlation term in the Reynolds stress transport equations, extensive use has been made of its exact properties. These, for example, have been employed in obtaining the widely used LRR model. Some recent proposals have dropped one of these properties to obtain new models. We demonstrate, by computing some simple homogeneous flows, that doing so does not lead to any significant improvements over the LRR model and it is not the right direction in improving the performance of existing models.

Shabbir, Aamir↗
NASA NTRS1977

An experimental study of the fracture behavior of laminated graphite/epoxy composites

The results of an experimental investigation on the fracture behavior of unidirectional and multidirectional laminated graphite/epoxy composites is reported. Critical tensile fracture stresses for constant head rate uniaxial specimens containing single-edge notches, double-edge notches, and centrally located circular holes are presented. Results are reported for loads and notches at various angles to the fiber direction. Evidence of notch sensitivity and stable crack growth is presented. Self-similar crack growth is shown to occur for only a limited set of circumstances. Critical stresses are compared to the theories of Waddoups et al and Whitney et al. These comparisons are presented using isotropic and orthotropic stress concentration factors together with a finite width correction factor. The results tend to show that use of only isotropic correction factors allow good correlation between theory and experiment.

Brinson, H. F.↗
NASA NTRS1980

Mode I fracture behavior of nonlinear materials

A finite element analysis is presented for the Mode I fracture behavior of cracked plates (stationary crack) made of different nonlinear materials (elastoplastic or elastic locking). The assumed stress-strain behavior of the nonlinear materials was piecewise linear. For each given 'stationary' crack size, the corresponding critical remote tensile stress was calculated based on the maximum crack-tip stress failure criterion. It was found that in the log-log plots of the critical remote stress versus critical crack length, the fracture data of the piecewise linear materials obey a 'stepwise-linear-inverse-square-root' fracture law. It is also shown how the fracture data of the piecewise linear materials can be fitted by proper piecewise graphical shifting of the classical 'inverse-square-root' fracture curve for the linearly elastic materials.

Ko, W. L.↗
NASA NTRS1996

(abstract) Ekman Pumping/Suction and Wind-Driven Ocean Circulation from ERS-1 Scatterometer Measurements Over the Arabian Sea During October 1994-October 1995

Spatial variations of the east-west and north-south components of surface wind stress are critical in studies of ocean circulation and biological-physical interactions because surface wind stress curl produces a vertical velocity in the upper ocean at the bottom of the Ekman Layer.The ERS-1 scatterometer provides reasonable coverage and direct measurements of vector of winds. Three schemes are evaluated relative to high-quality moored-bouy wind observations recorded in the central Arabian Sea, where high surface waves and high atmospheric water content during the southeast monsoon adversely affect the estimation of satellite-derived winds.

scatterometer↗
NASA NTRS1993

Determination of fiber-matrix interface failure parameters from off-axis tests

Critical fiber-matrix (FM) interface strength parameters were determined using a micromechanics-based approach together with failure data from off-axis tension (OAT) tests. The ply stresses at failure for a range of off-axis angles were used as input to a micromechanics analysis that was performed using the personal computer-based MICSTRAN code. FM interface stresses at the failure loads were calculated for both the square and the diamond array models. A simple procedure was developed to determine which array had the more severe FM interface stresses and the location of these critical stresses on the interface. For the cases analyzed, critical FM interface stresses were found to occur with the square array model and were located at a point where adjacent fibers were closest together. The critical FM interface stresses were used together with the Tsai-Wu failure theory to determine a failure criterion for the FM interface. This criterion was then used to predict the onset of ply cracking in angle-ply laminates for a range of laminate angles. Predictions for the onset of ply cracking in angle-ply laminates agreed with the test data trends.

Naik, Rajiv A.↗
NASA NTRS1975

Effect of hydrogen on the mechanical properties of titanium and its alloys

Occluded hydrogen resulting from cathodic charging of commercially pure titanium and titanium alloys, Ti-8Al-1Mo-1V and Ti-6Al-4V, was shown to cause embrittlement of the alloys. Embrittlement was a function of the interstitial hydrogen content rather than the amount of precipitated titanium hydride. The effects of hydrogen concentration on the critical strain for plastic instability along pure shear directions was determined for alloys Ti-8Al-1Mo-1V and Ti-5Al-2.5Sn. Hydrogen, in concentrations below that necessary for spontaneous hydride precipitation, increased the strain necessary for instability formation or instability failure. The strain rate sensitivity also increased with increasing hydrogen concentration. The effect of hydrogen on slip and twinning was determined for titanium single crystals. The critical resolved shear stress for prism slip was increased and the critical resolved shear stress for twinning was decreased with increasing hydrogen concentration.

Beck, F. H.↗
NASA NTRS1995

Active vibration control of structures undergoing bending vibrations

An active vibration control subassembly for a structure (such as a jet engine duct or a washing machine panel) undergoing bending vibrations caused by a source (such as the clothes agitator of the washing machine) independent of the subassembly. A piezoceramic actuator plate is vibratable by an applied electric AC signal. The plate is connected to the structure such that vibrations in the plate induced by the AC signal cause canceling bending vibrations in the structure and such that the plate is compressively pre-stressed along the structure when the structure is free of any bending vibrations. The compressive prestressing increases the amplitude of the canceling bending vibrations before the critical tensile stress level of the plate is reached. Preferably, a positive electric DC bias is also applied to the plate in its poling direction.

Pla, Frederic G.↗
NASA NTRS2000

A Study of Influencing Factors on the Tensile Response of a Titanium Matrix Composite With Weak Interfacial Bonding

The generalized method of cells micromechanics model is utilized to analyze the tensile stress-strain response of a representative titanium matrix composite with weak interfacial bonding. The fiber/matrix interface is modeled through application of a displacement discontinuity between the fiber and matrix once a critical debonding stress has been exceeded. Unidirectional composites with loading parallel and perpendicular to the fibers are examined, as well as a cross-ply laminate. For each of the laminates studied, analytically obtained results are compared to experimental data. The application of residual stresses through a cool-down process was found to have a significant effect on the tensile response. For the unidirectional laminate with loading applied perpendicular to the fibers, fiber packing and fiber shape were shown to have a significant effect on the predicted tensile response. Furthermore, the interface was characterized through the use of semi-emperical parameters including an interfacial compliance and a "debond stress;" defined as the stress level across the interface which activates fiber/matrix debonding. The results in this paper demonstrate that if architectural factors are correctly accounted for and the interface is appropriately characterized, the macro-level composite behavior can be correctly predicted without modifying any of the fiber or matrix constituent properties.

Goldberg, Robert K.↗