SEARCH · Search NASA

Results for “Capacity estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

DOE OSTI2018

Laboratory synthesis of C3S on the kilogram scale

An optimized process using amorphous silica for efficient C{sub 3}S synthesis in the laboratory is reported: an estimated production capacity of ~2 kg C{sub 3}S within a week is possible. Amorphous silica (fumed silica) was used as raw material and inter-ground with CaCO{sub 3} and water for C{sub 3}S synthesis, the dried raw mixture has sufficient green strength to be self-supporting, which allows large cylinders to be placed in Platinum crucibles. The mineral composition of the sintered sample was quantified with X-ray powder diffraction using Rietveld analysis. C{sub 3}S with 3 S synthesis was dramatically enhanced because of 1) increased burnability of the raw mix due to amorphous silica and very fine CaCO{sub 3} particles after grinding, 2) simplified sample preparation process avoiding pressing discs and 3) improved capacities of the crucible and furnace.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Evaluation of chromatographic resins for high efficacy separation of radium from chemical analogues

The separation of Radium (Ra) from interfering chemical analogues is of major importance for both the accurate measurement of Ra-226 in environmental samples and the preparation of radium targets destined for medical isotope production. The adsorption behavior of Ra, Barium (Ba), and Strontium (Sr) was investigated on multiple crown-ether-based proprietary extraction chromatographic resins developed by TrisKem Int. Among these, the TK101 resin, characterized by a novel room-temperature ionic liquid (RTIL) dual extractant–solvent system, demonstrated enhanced affinity and selectivity, particularly at low acid concentrations, achieving a D w of 3477 ± 73 for Ra in 0.04 M HNO₃, whereas the maximum Ra D w obtained with the traditional Sr resin in 8 M HNO 3 was only 12.33 ± 0.4. In 0.04 M HNO 3 , a Ra distribution ratio (D w ) of 776 was achieved within 1 min, indicating rapid uptake kinetics. The adsorption capacities were estimated at 19.6 ± 0.1 mg/g for Ba and 12.0 ± 0.2 mg/g for Sr. However, competing alkali metals significantly reduced alkaline earth metal uptake, indicating that the TK101 resin is best suited for radium purification following a preconcentration step to minimize matrix effects in high salinity samples. Dynamic column studies confirmed the strong chromatographic performance of the TK101 resin, with no significant Ba or Sr breakthrough in the Ra fraction and a Ra recovery of 87 ± 2.8%. These results demonstrate the potential of the TK101 resin for selective radium separation in analytical and radiochemical applications.

and nuclear chemistry↗

DOE OSTI2022

Tradeoffs in forest resilience to satellite-based estimates of water and productivity losses

Climate change is expected to intensify the global hydrological cycle via increased evapotranspiration (ET). Changes in ET have important consequences for water-related ecosystem services as well as for forest productivity. Forests play a critical role in ET: active trees sequester carbon at the expense of losing water, yet if they are not active, water remains in the trees, but productivity stalls. Here, we estimated the capacity of forests to recover (resilience) from extreme water or productivity losses based on modeled ET through remote sensing methods across the conterminous USA. Results show there is a spatial tradeoff in resilience to water or productivity losses. Forests were more resilient to water loss in the drier west, and more resilient to productivity loss in the wetter east. Still, resilience was highly heterogeneous across the continent. Projections under climate change indicate both declines and increases of up to 13% in forest resilience, with broad regional trends but high spatial heterogeneity within regions. This study brings crucial satellite-based insights on how water dynamics, and consequentially productivity and water provision in forests, might be impacted by climate change.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2018

Improved Sensitivity and Separations for Phosphopeptides using Online Liquid Chromotography Coupled with Structures for Lossless Ion Manipulations Ion Mobility–Mass Spectrometry

Phosphoproteomics greatly augments proteomics and holds tremendous potential for insights into the modulation of biological systems for various disease states, etc. However, numerous challenges hinder conventional methods in terms of measurement sensitivity, throughput, and capabilities for confident phosphopeptide and phosphosite identification. In this work, we report the first example of integrating structures for lossless ion manipulations ion mobility (SLIM) IM-MS with online reversed-phase liquid chromatography (LC) to evaluate its potential for addressing the aforementioned challenges. A mixture of 51 heavy-labeled phosphopeptides was analyzed with a SLIM IM module having integrated ion accumulation and long-path separation regions. The SLIM IM-MS provided improved sensitivity over an established LC-SRM method, with limits of detection as low as 50 pM (50 amol/µl) for several peptides. Conventionally problematic phosphopeptide isomers could be resolved following an 18 m SLIM IM separation. The 2-D peak capacity was estimated as ~9000 for 90 min LC separation coupled to an 18 m SLIM IM separation, considerably higher than LC alone and providing a basis for both improved identification and quantification, with additional gains projected with the future use of longer path SLIM IM separations. Thus, LC-SLIM IM-MS offers great potential for improving the sensitivity, separation, and throughput of phosphoproteomics analyses.

Chouinard, Christopher D.↗

DOE OSTI2015

Effectiveness of mineral soil to adsorb the natural occurring radioactive material (norm), uranium and thorium

A study has been performed on U-soil and Th-soil adsorption of three types of soil collected from Selangor State of Malaysia which are Saujana Putra, Bukit Changgang and Jenderam Hilir. In this study, natural radionuclide (U and Th) soil adsorption based on batch experiments with various initial concentrations of the radionuclide elements were carried out. Parameters that were set constant include pH at 5;amount of soil used was 5 g each, contact time was 24 hour and different initial concentration for each solution of U and Th which is 5 mg/L, 10 mg/L, 15 mg/L, 20 mg/L, 25 mg/L and 40 mg/L were used. The K{sub d} values for each type of soil were determined in this batch experiments which was based on US-EPA method, in order to estimate adsorption capacity of the soil.The K{sub d} values of Th found higher than Kd values of U for all of the soil samples, and the highest was found on the soil collected from Bukit Changgang. The soil clay content was one of factors to influence the adsorption of both U and Th from dilute initial solution. The U-soil and Th-soil adsorption process for all the soil samples studied are generally obeying unimolecular layer Langmuir isotherm model. From Langmuir isotherm, the maximum adsorption capacity for U was 0.393mg/g and for Th was 1.53 mg/g for the soil that was taken from Bukit Changgang. From the study, it suggested that the soil from Bukit Changgang applicable as potential enhanced barrier for site disposing waste containing U and Th.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2016

Graphene oxide and adsorption of chloroform: A density functional study

Chlorinated hydrocarbon compounds are of environmental concerns, since they are toxic to humans and other mammals, and are widespread, and exposure is hard to avoid. Understanding and improving methods to reduce the amount of the substances are important. We present an atomic-scale calculational study of the adsorption of chlorine-based substance chloroform (CHCl{sub 3}) on graphene oxide, as a step in estimating the capacity of graphene oxide for filtering out such substances, e.g., from drinking water. The calculations are based on density functional theory, and the recently developed consistent-exchange functional for the van der Waals density-functional method is employed. We obtain values of the chloroform adsorption energy varying from roughly 0.2 to 0.4 eV per molecule. This is comparable to previously found results for chloroform adsorbed directly on clean graphene, using similar calculations. In a wet environment, like filters for drinking water, the graphene will not stay clean and will likely oxidize, and thus adsorption onto graphene oxide, rather than clean graphene, is a more relevant process to study.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2017

Fast optimization algorithms and the cosmological constant

Denef and Douglas have observed that in certain landscape models the problem of finding small values of the cosmological constant is a large instance of a problem that is hard for the complexity class NP (Nondeterministic Polynomial-time). The number of elementary operations (quantum gates) needed to solve this problem by brute force search exceeds the estimated computational capacity of the observable Universe. Here in this paper, we describe a way out of this puzzling circumstance: despite being NP-hard, the problem of finding a small cosmological constant can be attacked by more sophisticated algorithms whose performance vastly exceeds brute force search. In fact, in some parameter regimes the average-case complexity is polynomial. We demonstrate this by explicitly finding a cosmological constant of order 10 -120 in a randomly generated 10 9 -dimensional Arkani-Hamed–Dimopoulos–Kachru landscape.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2023

GRAF-Plan for Vietnam

Evaluates the reserve requirements for power system balancing areas based on variability and uncertainty of load as well as wind and solar generation scenarios. The tool uses minute‐by‐minute site‐specific generation and load information, as well as information from generation and load forecasting algorithms used in the balancing areas. The Balancing‐Plan Tool can be used directly by utility planners and operators to aid in the integration of intermittent renewable resources. The tool provides reserve requirements of various kinds, such as day‐ahead, load following and regulation, as well as estimates the capacity of the generation fleet to provide the require reserves.

Campbell, Allison↗

DOE OSTI2024

Solar Photovoltaics and Land-Based Wind Technical Potential and Supply Curves for the Contiguous United States (2023 Edition)

Estimates of the potential of renewable energy are essential for understanding how we can decarbonize our electric grid and economy. They provide key data for policymakers, land managers, and energy modelers by defining the quantity, quality, and cost of renewable resources. However, estimating renewable energy potential is challenging and requires frequent updates because of rapid advances in technology, cost reductions, and uncertainty about developable land that are due to social, regulatory, and environmental factors. Additionally, the complex processes involved in renewable energy development require regular reviews of methods and assumptions, which can also impact our understanding of renewable potential. In this, the 2023 edition of this annual report, we present new estimates of the technical potential for land-based wind and solar photovoltaics (PV) for the contiguous United States (CONUS). We also provide cost estimates for the available resources, presenting representative supply curves that can be used in downstream modeling and analysis. Additionally, we introduce the new methodologies used to estimate wind capacity, wind energy losses, transmission cost and representation, updated technology cost and design, and scenarios of siting constraints designed to help bound the uncertainty of renewable potential.

14 SOLAR ENERGY↗

DOE OSTI2020

Experimental Warming Changes Phenology and Shortens Growing Season of the Dominant Invasive Plant Bromus tectorum (Cheatgrass)

Bromus tectorum (cheatgrass) has successfully invaded and established throughout the western United States. Bromus tectorum grows early in the season and this early growth allows B. tectorum to outcompete native species, which has led to dramatic shifts in ecosystem function and plant community composition after B. tectorum invades. If the phenology of native species is unable to track changing climate as effectively as B. tectorum’s phenology then climate change may facilitate further invasion. To better understand how B. tectorum phenology will respond to future climate, we tracked the timing of B. tectorum germination, flowering, and senescence over a decade in three in situ climate manipulation experiments with treatments that increased temperatures (2°C and 4°C above ambient), altered precipitation regimes, or applied a combination of each. Linear mixed-effects models were used to analyze treatment effects on the timing of germination, flowering, senescence, and on the length of the vegetative growing season (time from germination to flowering) in each experiment. Altered precipitation treatments were only applied in early years of the study and neither precipitation treatments nor the treatments’ legacies significantly affected B. tectorum phenology. The timing of germination did not significantly vary between any warming treatments and their respective ambient plots. However, plots that were warmed had advances in the timing of B. tectorum flowering and senescence, as well as shorter vegetative growing seasons. The phenological advances caused by warming increased with increasing degrees of experimental warming. The greatest differences between warmed and ambient plots were seen in the length of the vegetative growing season, which was shortened by approximately 12 and 7 days in the +4°C and +2°C warming levels, respectively. The effects of experimental warming were small compared to the effects of interannual climate variation, suggesting that interactive controls and the timing of multiple climatic factors are important in determining B. tectorum phenology. Taken together, these results help elucidate how B. tectorum phenology may respond to future climate, increasing our predictive capacity for estimating when to time B. tectorum control efforts and how to more effectively manage this exotic annual grass.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1987

Thermodynamic state of SO2 on Io's surface

It has been suggested that surface conditions on Io might be conducive to significant SO2 adsorption on sulfur or alkali sulfides. A number of spectroscopic arguments for and against the high abundance of a SO2 adsorbate (versus frost) on Io have been made. SO2 absorption isotherms on particulate sulfur are measured, and the question of SO2 adsorbate/ice is approached from a thermodynamic perspective. Because of formidable experimental difficulties, data were not obtained at the very low temperatures and P(SO2) characteristics of Io; however, data were obtained over a wide range of pressures and temperatures somewhat higher than Io's and extrapolated to Io surface conditions. Errors in estimating adsorptive capacity accrue through extrapolation of the adsorption isotherms; however, more significant is the addition of the solid SO2 equilibrium vapor pressure curve to the phase diagram. The formation of ice places a strict upper limit on adsorptive coverage at any temperature. The limit for Io based upon the data is calculated, and it is shown that no more than 0.014 monolayers of SO2 can adsorb on sulfur at Io temperatures. Given the assumption that sulfur forms the primary adsorbent on Io's surface, or the assumption that the adsorptive capacity of the other adsorbents is not substantially greater than that of sulfur, this explains the fact that the nu(1) + nu(3) band center position is in better agreement with that of frost than adsorbate.

Zent, Aaron P.↗

NASA NTRS2006

An Update on the Performance of Li-Ion Rechargeable Batteries on Mars Rovers

NASA's Mars Rovers, Spirit and Opportunity have been exploring the surface of Mars for the last thirty months, far exceeding the primary mission life of three months, performing astounding geological studies to examine the habitability of Mars. Such an extended mission life may be attributed to impressive performances of several subsystems, including power subsystem components, i.e., solar array and batteries. The novelty and challenge for this mission in terms of energy storage is the use of lithium-ion batteries, for the first time in a major NASA mission, for keeping the rover electronics warm, and supporting nighttime experimentation and communications. The use of Li-ion batteries has considerably enhanced or even enabled these rovers, by providing greater mass and volume allocations for the payload and wider range of operating temperatures for the power subsystem and thus reduced thermal management. After about 800 days of exploration, there is only marginal change in the end-of discharge (EOD) voltages of the batteries or in their capacities, as estimated from in-flight voltage data and corroborated by ground testing of prototype batteries. Enabled by such impressive durability from the Li-ion batteries, both from a cycling and calendar life stand point, these rovers are poised to extend their exploration well beyond 1000 sols, though other components have started showing signs of decay. In this paper, we will update the performance characteristics of these batteries on both Spirit and Opportunity.

low temperatures↗

NASA NTRS2006

Estimation of Reduction in Airspace Capacity Due to Convective Weather

Severe convective weather routinely disrupts normal flow of air traffic in the United States' National Airspace System (NAS). Over the last decade, severe weather has been the most significant cause, accounting for over 70% of air traffic delays in the NAS. Flights incur modification in their nominal routes due to the presence of severe weather, and hence, suffer increased delays. These delays contribute to increased burden on airlines due to extra fuel costs and missed schedules for connecting flights. In this paper, the reduction in air space capacity and the associated air traffic delays due to severe convective weather will be investigated.

Sheth, Kapil↗

NASA NTRS2012

Phonon Mechanisms for Excess Heat Capacity in Membrane Isolated Superconducting Transition Edge Sensors

The mechanics of phonon transport in membrane-isolated superconducting transition edge sensors is discussed. Surveys of the literature on this type of sensor reveal a number of designs with excess heat capacity and a smaller subset that exhibit decoupling of the superconducting film from the underlying dielectric. A simple model is addressed in which the membrane, despite its thermal isolation, fails to fully thermalize to the temperature of the metal film heating it. A population of phonons exists which is emitted by the metal film, partially thermalizes the dielectric and is then reabsorbed in the metal film without escaping from the device structure to the thermal bath. The size of this population and its contribution to the heat capacity are estimated for several device scenarios.

Chervenak, James A.↗

NASA NTRS2012

Phonon Mechanisms for Excess Heat Capacity in Membrane Isolated Superconducting Transition Edge Sensors

Chervenak, James A.↗

NASA NTRS2018

Tactical Surface Metering Procedures for Charlotte Douglas International Airport

NASA has been collaborating with the Federal Aviation Administration (FAA) and aviation industry partners to develop and demonstrate new concepts and technologies for the Integrated Arrival, Departure, and Surface (IADS) traffic management capabilities under the Airspace Technology Demonstration 2 (ATD-2) project. The primary goal of the ATD-2 project is to improve the predictability and the operational efficiency of the air traffic system in metroplex environments while maintaining or improving throughput by enhancing and integrating arrival, departure and surface prediction, scheduling, and management systems. In the Phase 1 Baseline IADS Demonstration, the tactical surface scheduling capability and the user interfaces for ramp controllers and ramp traffic managers were implemented for ramp operations. The purpose of the tactical surface scheduling capability is to provide the airline ramp controller with aircraft pushback advisories that prevent surface congestion and to respond to surface and airspace constraints that become known over relatively short time horizons. For this purpose, the tactical surface metering tool first estimates the capacity of current and near-future runway resources from flight schedule and surveillance data. With demand forecasts and predicted taxi trajectories, this tool computes an efficient runway schedule of aircraft in the planning horizon based on their readiness, Earliest Off-Block Times (EOBTs), and a ration by schedule (RBS) rule. Details on the implementation of the Tactical Surface Metering tool will be provided in the full paper. Both pushback and recommended hold times advisories provided by this surface metering tool are shown on the user interfaces for the ramp controller and the ramp traffic manager, called Ramp Traffic Console (RTC) and Ramp Manager Traffic Console (RMTC), respectively. There is excess queue time in the system due to demand capacity imbalance, this time can be taken as a hold on the runway queue or at the gate and was referred to as the Metering Value. This metering value can be adjusted by the Ramp Manager in collaboration with Air Traffic Controller-Tower Traffic Management Coordinator (TMC). They selected a set of metering values as default values for the tool during human-in-the-loop simulation. As the metering value increases, there is a decrease in the gate hold and increase in the queue time at the runway. Procedures and Information needs related to managing the surface metering procedures were researched in the simulated environment. These procedures will be compared to the procedures adopted at Charlotte Douglas International Airport when the tools were deployed and adopted in November 2017 for one departure push bank per day. Feedback regarding initial issues, information needs such as the need to see EOBTs on the flight data tags and how they compare to scheduled times will also be discussed in the full paper. Initial results will be provided regarding the choice of the metering value and how it was adjusted on a daily basis and what procedures evolved will also be presented in the paper.

surface metering↗

DOE OSTI2016

Parameterizing the Variability and Uncertainty of Wind and Solar in CEMs

We present current and improved methods for estimating the capacity value and curtailment impacts from variable generation (VG) in capacity expansion models (CEMs). The ideal calculation of these variability metrics is through an explicit co-optimized investment-dispatch model using multiple years of VG and load data. Because of data and computational limitations, existing CEMs typically approximate these metrics using a subset of all hours from a single year and/or using statistical methods, which often do not capture the tail-event impacts or the broader set of interactions between VG, storage, and conventional generators. In our proposed new methods, we use hourly generation and load values across all hours of the year to characterize the (1) contribution of VG to system capacity during high load hours, (2) the curtailment level of VG, and (3) the reduction in VG curtailment due to storage and shutdown of select thermal generators. Using CEM model outputs from a preceding model solve period, we apply these methods to exogenously calculate capacity value and curtailment metrics for the subsequent model solve period. Preliminary results suggest that these hourly methods offer improved capacity value and curtailment representations of VG in the CEM from existing approximation methods without additional computational burdens.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2017

Update on Geothermal Direct-Use Installations in the United States

Direct-use of geothermal energy currently has limited penetration in the United States, with an estimated installed capacity of about 500 MWth, supplying on the order of 0.01% of the total annual U.S. heat demand (about 30 EJ). We see higher penetration levels in other countries such as Iceland (about 90%) and Hungary (2.5%). An updated database of geothermal direct-use systems in the U.S. has been compiled and analyzed, building upon the Oregon Institute of Technology (OIT) Geo-Heat Center direct-use database. Types of directuse applications examined include hot springs resorts and pools, aquaculture farms, greenhouses, and district heating systems, among others; power-generating facilities and ground-source heat pumps were excluded. Where possible, the current operation status, open and close dates, well data, and other technical data were obtained for each entry. The database contains 545 installations, of which 407 are open, 108 are closed, and 30 have an unknown status. Spas are the most common type of installation, accounting for 50% of installations by number. Aquaculture installations (46 out of 407 open installations) account for the largest percentage (26%) of installed capacity in operation (129 MWth out of 501 MWth). Historical deployment curves show the installed capacity significantly increased in the 1970s and 1980s mainly due to development of geothermal district heating, aquaculture, and greenhouse systems. Since the 2000s, geothermal direct-use development appears to have slowed, and the number of sites in operation decreased due to closures. Case studies reveal multiple barriers to geothermal direct-use implementation and operation, including 1) existence of an information gap among stakeholders, developers, and the general public, 2) competition from cheap natural gas, and 3) the family-owned, small-scale nature of businesses might result in discontinuation among generations.

15 GEOTHERMAL ENERGY↗