SEARCH · Search NASA

Results for “Combined loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS2003

Single Vector Calibration System for Multi-Axis Load Cells and Method for Calibrating a Multi-Axis Load Cell

A single vector calibration system is provided which facilitates the calibration of multi-axis load cells, including wind tunnel force balances. The single vector system provides the capability to calibrate a multi-axis load cell using a single directional load, for example loading solely in the gravitational direction. The system manipulates the load cell in three-dimensional space, while keeping the uni-directional calibration load aligned. The use of a single vector calibration load reduces the set-up time for the multi-axis load combinations needed to generate a complete calibration mathematical model. The system also reduces load application inaccuracies caused by the conventional requirement to generate multiple force vectors. The simplicity of the system reduces calibration time and cost, while simultaneously increasing calibration accuracy.

Parker, Peter A.↗

NASA NTRS2004

Structural Integrity of a Wind Tunnel Balance

The National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) has been designing strain-gage balances for utilization in wind tunnels since its inception. The utilization of balances span over a wide variety of aerodynamic tests. A force balance is an inherently critically stressed component due to the requirements of measurement sensitivity. Research and analyses are done in order to investigate the structural integrity of the balances as well as developing an understanding of their performance in order to enhance their capability. Maximum loading occurs when all 6 components of the loads are applied simultaneously with their maximum value allowed (limit load). This circumstance normally does not occur in the wind tunnel. However, if it occurs, is the balance capable of handling the loads with an acceptable factor of safety? LaRC Balance 1621 was modeled and meshed in PATRAN for analysis in NASTRAN. For a complete analysis, it is necessary to consider all the load cases as well as use dense mesh near all the edges. Because of computer limitations, it is not possible to have one model with the dense mesh near all edges. In the present study, a dense mesh is limited to the surface corners where the cage and axial sections meet. Four different load combinations are used for the current analysis. Linear analysis is performed for each load case. In the case where the stress value is above linear elastic region, it is necessary to perform nonlinear analysis. It is also important to investigate the variables limiting the structural integrity of the balances. In order to investigate the possibility of modifying the existing balances to enhance the structural integrity, some modifications are done on this balance. The structural integrity of the balance after modification is investigated.

Karkehabadi, R.↗

DOE OSTI2020

Multi-modular power plant with dedicated electrical grid

A multi-modular power plant includes a plurality of on-site nuclear power modules that generate a power plant output, and a number of power plant systems which operate using electricity associated with a house load of the power plant. A switchyard associated with the power plant may electrically connect the power plant to a distributed electrical grid. The distributed electrical grid may be configured to service a plurality of geographically distributed consumers. Additionally, the switchyard may electrically connect the power plant to a dedicated electrical grid. The dedicated electrical grid may provide electricity generated from the power plant output to a dedicated service load, and the power plant output may be equal to or greater than a combined load of the dedicated service load and the house load. At least a portion of the power plant output may be distributed to both the power plant systems and the dedicated electrical grid.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1981

Strength integrity of the Space Shuttle Orbiter tiles

The development of the thermal protection system (TPS) for shielding the Shuttle from high temperature aerodynamic heating during atmospheric entry is described. The TPS was required to limit structural heating to 350 F, be used for 100 flights, withstand temperature ranges from -250 to 2800 F, attach to an aluminum structure, and provide the aerodynamic moldline. More than 30,000 tiles of individual size, shape, and strength were bonded adhesively to a Nomex felt mat which coated critical areas of the craft. Densification processes for strengthening the tiles in highly loaded areas are outlined and stress sources for each mission phase are analyzed. Aerodynamic, acoustic, combined loads, and verification tests for stress levels up to 125% of nominal were performed for each tile. The one complete and 15 partial tiles lost during the initial flight were all lower strength, undensified tiles.

Moser, T. L.↗

NASA NTRS1974

Delay in fatigue crack growth

The importance of delay, or retardation in the rate of fatigue crack growth, produced by load interactions in variable amplitude loading on the accurate prediction of fatigue lives of engineering structures has been well recognized for some time. Heretofore, only a few simple loading combinations or spectra have been examined systematically. In this investigation the effects of a broad range of loading variables on delay in fatigue crack growth at room temperature are examined for a mill annealed Ti-6Al-4V alloy. The results are used to estimate crack growth behavior under programmed loads.

Wei, R. P.↗

NASA NTRS1986

Case histories involving fatigue and fracture mechanics; Proceedings of the Symposium, Charleston, SC, Mar. 21, 22, 1985

Papers are presented on cracking at nozzle corners in the nuclear pressure vessel industry, applied fracture mechanics for assessing defect significance in a crude oil pipeline, failure analysis of a large wind-tunnel compressor blade, analysis of a compressor-wheel failure, and preventing fracture by inspection and analysis. Consideration is also given to the fatigue crack growth predictions of welded aircraft structures containing flaws in the residual stress field, the fatigue and fracture mechanics analysis of a compression loaded aircraft structure, fracture of an aircraft horizontal stabilizer, fatigue life analysis of fuel tank skins under combined loads, and aircraft structural maintenance recommendations based on fracture mechanics analysis. Additional papers discuss an analysis of two metal-forming die failures, an analysis of a failed saw arbor, and the role of fracture mechanics in assessing the effect on fatigue life of design changes in welded fabrications.

Hudson, C. Michael↗

NASA NTRSDate not supplied

3D Woven Composite End Ring Structure: Design Development and Verification Testing

The National Aeronautics and Space Administration (NASA) Space Technology and Mission Directorate (STMD) is advancing composite technologies for exploration missions. The Composite Technology for Exploration (CTE) project goal is to advance lightweight joint concepts for Space Launch System (SLS) class structures. To this end CTE is developing and demonstrating a 3D woven carbon /epoxy composite joint design co-bonded in a circumferential end ring configuration, applied to a SLS sized conceptual payload attachment structure. This joint is a lightweight alternative to heavy and costly metallic joints. The 3D woven joint development advances lightweight joint technologies through material and structural design, material and joint analyses, and fabrication, as well as demonstration through building block testing. Prior limited building block tests are mentioned. In this paper, new sub-element-scale test results are described that demonstrate the structural capability well beyond design limit load. Then, results for a sub-component test article with a 889 mm joint subjected to combined loads are presented.

Kenneth N Segal↗

NASA NTRS1976

Optimum design of composite laminates with thermal effects

An analytical approach to determine an optimum laminate for a variety of thermal and mechanical loading combinations is presented. The analysis is performed for a linear elastic material under static mechanical and uniform thermal loadings. The problem is restricted to a unit width and length laminate with angle orientations resulting in an orthotropic, symmetric, and balanced configuration. An objective function defining total strain energy, is formulated and an optimum laminate design determined subject to constraints on stiffness, average coefficient of thermal expansion, and strength. The objective function is formulated in terms of the orientation angles, number of plies, and material properties. The method presented has, in varying degrees, shown that the design of a laminate can be accomplished using strain energy minimization as the primary criteria. The results of various combinations of applied constraints in the optimized design process are presented and discussed.

Markham, L. R.↗

NASA NTRS1982

Shuttle tile environments and loads

This paper presents the Shuttle tile ascent environments and outlines the procedures used to convert these environments into tile loads. Testing which was performed to quantify or verify the loads is also discussed, along with the load combination rationale. The discussion of the ascent environment is limited to the transonic/supersonic portion of the mission since mechanical design loads occur during this time, and to specific regions of the vehicle, in particular those regions in which undensified critical (black) tiles are located.

Muraca, R. J.↗

NASA NTRS1989

Transient Pressure Test Article Test Program

The Transient Pressure Test Article (TPTA) test program is being conducted at a new test facility located in the East Test Area at the National Aeronautics and Space Administration's (NASA's) Marshall Space Flight Center (MSFC) in Huntsville, Alabama. This facility, along with the special test equipment (STE) required for facility support, was constructed specifically to test and verify the sealing capability of the Redesigned Solid Rocket Motor (RSRM) field, igniter, and nozzle joints. The test article consists of full scale RSRM hardware loaded with inert propellant and assembled in a short stack configuration. The TPTA is pressurized by igniting a propellant cartridge capable of inducing a pressure rise rate which stimulates the ignition transient that occurs during launch. Dynamic loads are applied during the pressure cycle to simulate external tank attach (ETA) strut loads present on the ETA ring. Sealing ability of the redesigned joints is evaluated under joint movement conditions produced by these combined loads since joint sealing ability depends on seal resilience velocity being greater than gap opening velocity. Also, maximum flight dynamic loads are applied to the test article which is either pressurized to 600 psia using gaseous nitrogen (GN2) or applied to the test article as the pressure decays inside the test article on the down cycle after the ignition transient cycle. This new test facility is examined with respect to its capabilities. In addition, both the topic of test effectiveness versus space vehicle flight performance and new aerospace test techniques, as well as a comparison between the old SRM design and the RSRM are presented.

Vibbart, Charles M.↗

NASA NTRS1998

Design and Operating Characteristics of High-Speed, Small-Bore, Angular-Contact Ball Bearings

The computer program SHABERTH was used to analyze 35-mm-bore, angular-contact ball bearings designed and manufactured for high-speed turbomachinery applications. Parametric tests of the bearings were conducted on a high-speed, high-temperature bearing tester and were compared with the computer predictions. Four bearing and cage designs were studied. The bearings were lubricated either by jet lubrication or through the split inner ring with and without outer-ring cooling. The predicted bearing life decreased with increasing speed because of increased operating contact stresses caused by changes in contact angle and centrifugal load. For thrust loads only, the difference in calculated life for the 24 deg. and 30 deg. contact-angle bearings was insignificant. However, for combined loading, the 24 deg. contact-angle bearing gave longer life. For split-inner-ring bearings, optimal operating conditions were obtained with a 24 deg. contact angle and an inner-ring, land-guided cage, using outer-ring cooling in conjunction with low lubricant flow rates. Lower temperature and power losses were obtained with a single-outer-ring, land-guided cage for the 24 deg. contact-angle bearing having a relieved inner ring and partially relieved outer ring. Inner-ring temperatures were independent of lubrication mode and cage design. In comparison with measured values, reasonably good engineering correlation was obtained using the computer program SHABERTH for predicted bearing power loss and for inner- and outer-ring temperatures. The Parker formula for XCAV (used in SHABERTH, a measure of oil volume in the bearing cavity) may need to be refined to reflect bearing lubrication mode, cage design, and location of cage-controlling land.

Pinel, Stanley I.↗

NASA NTRS1988

Structural efficiency study of graphite-epoxy aircraft rib structures

Attention is given to the structural efficiencies obtainable with optimally designed graphite/epoxy wing rib panel configurations that are potentially economically manufacturable. Some ribs are commonly used as fuel cell closeout panels, and are accordingly subjected to out-of-plane pressure loads in addition to the in-plane axial compressive and shear loads resulting from the wing loading. The present minimum-weight panel designs satisfy buckling and strength constraints for wing rib panels subjected to a wide range of combined load conditions.

Swanson, Gary D.↗

NASA NTRS2010

Biomechanical Analysis of T2 Exercise

Crewmembers regularly perform treadmill exercise on the ISS. With the implementation of T2 on ISS, there is now the capacity to obtain ground reaction force (GRF) data GRF data combined with video motion data allows biomechanical analyses to occur that generate joint torque estimates from exercise conditions. Knowledge of how speed and load influence joint torque will provide quantitative information on which exercise prescriptions can be based. The objective is to determine the joint kinematics, ground reaction forces, and joint kinetics associated with treadmill exercise on the ISS. This study will: 1) Determine if specific exercise speed and harness load combinations are superior to others in exercise benefit; and 2) Aid in the design of exercise prescriptions that will be most beneficial in maintaining crewmember health.

DeWitt, John K.↗

DOE OSTI2025

Status Update for the Bearing Test Article Design Development – FY2025

Argonne National Laboratory’s (ANL) Mechanism Engineering Test Loop (METL) team has completed the design of a new Bearing Test Article (BTA) to test mechanical bearings for sodium fast reactor (SFR) mechanism applications. Recognition of the need for further bearing testing arose due to failure of rolling element bearings during testing of components for in-vessel fuel handling machines (FHMs) conducted at ANL in the METL facility. While the initial concept of the BTA arose from a need for bearing testing for FHM applications, the BTA design is configurable to test bearings of various sizes, types, and materials submerged in liquid sodium. Requirements for loading, shaft speed, temperature, and bearing size range were chosen based on requirements for SFR fuel handling. Modular components in the test bearing housings and shaft sleeves allow the design to accommodate a wide range of bearing sizes without modification to the larger assembly. Loading will be applied with screw jacks on the air side of the test article that will be adjusted to apply radial, thrust, or combined loading conditions. Applied force will be measured by load cells in-line with the loading mechanisms. In FY25 we have completed the design of the test article that will be fabricated and undergo testing at the METL facility. Drawing packages for the fabrication of the test article have been drafted and are being reviewed to add part tolerances and we have started ordering off-the-shelf components. The report will summarize the development of the Bearing Test Article design starting with an overview of the entire test article, then a more detailed examination of the bearing test section, loading mechanisms, test article ports and seals, and support structures, including analysis that went into significant design choices.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1981

Shuttle tile environments and loads

This paper will discuss the Shuttle tile ascent environments and outline the procedures used to convert these environments into tile loads. Testing which was performed to quantify or verify the loads will also be discussed, along with the load combination rationale which was used. The discussion of the ascent environment will be limited to the transonic/supersonic portion of the mission since mechanical design loads occur during this time, and to specific regions of the vehicle, in particular those regions in which undensified critical (black) tiles are located. The induced environments can be broken down into three categories. The first of these are aerodynamic environments. These, in turn, are broken down into two categories-- (I) quasi-steady, which includes spatial surface pressure gradients, pressure differentials due to vent lag, and skin friction, and (2) the unsteady aerodynamics (aero-buffet). The second induced environment is defined as the vibration of the skin-stringer aluminum panels (hereafter referred to as the substrate) due to the acoustic environment. The third environment is defined as a quasi-steady substrate deflection, which results from in-plane and out-of-plane substrate loads.

Ralph J. Muraca↗

NASA NTRS1997

Buckling Behavior of Long Symmetrically Laminated Plates Subjected to Shear and Linearly Varying Axial Edge Loads

A parametric study of the buckling behavior of infinitely long symmetrically laminated anisotropic plates that are subjected to linearly varying edge loads, uniform shear loads, or combinations of these loads is presented. The study focuses on the effects of the shape of linearly varying edge load distribution, plate orthotropy, and plate flexural anisotropy on plate buckling behavior. In addition, the study exmines the interaction of linearly varying edge loads and uniform shear loads with plate flexural anisotropy and orthotropy. Results obtained by using a special purpose nondimensional analysis that is well suited for parametric studies of clamped and simply supported plates are presented for [+/- theta](sub s), thin graphite-epoxy laminates that are representative of spacecraft structural components. Also, numerous generic buckling-design charts are presented for a wide range of nondimensional parameters that are applicable to a broad class of laminate constructions. These charts show explicitly the effects of flexural orthotropy and flexural anisotropy on plate buckling behavior for linearly varying edge loads, uniform shear loads, or combinations of these loads. The most important finding of the present study is that specially orthotropic and flexurally anisotropic plates that are subjected to an axial edge load distribution that is tension dominated can support shear loads that are larger in magnitude than the shear buckling load.

Nemeth, Michael P.↗

DOE OSTI2020

Combined Heat and Power Technology Fact Sheet Series: District Energy

This fact sheet provides an overview of district energy systems, which are characterized by one or more central plants producing hot water, steam, and/or chilled water, which then flows through a network of insulated pipes to provide hot water, space heating, and/or air conditioning for nearby buildings. District energy systems serve a variety of end-use markets, including downtowns (central business districts), college and university campuses, hospitals and healthcare facilities, airports, military bases, and industrial complexes. By combining loads for multiple buildings, district energy systems create economies of scale that help reduce energy costs and enable the use of high-efficiency technologies such as combined heat and power (CHP).

Combined Heat and Power, CHP, District Energy, Tec↗

NASA NTRS2012

Aerospace Threaded Fastener Strength in Combined Shear and Tension Loading

A test program was initiated by Marshall Space Flight Center and sponsored by the NASA Engineering and Safety Center to characterize the failure behavior of a typical high-strength aerospace threaded fastener under a range of shear to tension loading ratios for both a nut and an insert configuration where the shear plane passes through the body and threads, respectively. The testing was performed with a customized test fixture designed to test a bolt with a single shear plane at a discrete range of loading angles. The results provide data to compare against existing combined loading failure criteria and to quantify the bolt strength when the shear plane passes through the threads.

Threaded fastener↗